English dropdown-ico

Manual GE DBI.333

24 pages 0.62 mb
Download

Go to site of 24

Summary
  • GE DBI.333 - page 1

    GEAppliances.com DBL333 DCL333 DVL223 Dr y ers 134098700 175D1807P367 49-90105 08-01 JR Safety Instr uctions . . . . . . . . . 2–5 Operating Instr uctions Control Panels . . . . . . . . . . . . . . . .6 Control Settings . . . . . . . . . . . . . . .7 Loading and Using the Dryer . . .8, 9 Installation Instr uctions Electrical Requirements . . . . ...

  • GE DBI.333 - page 2

    IMPORT ANT SAFETY INFORMA TION. READ ALL INSTRUCTIONS BEFORE USING. 2 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions W ARNING! For your safety , the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, perso ...

  • GE DBI.333 - page 3

    ■ Properly ground dryer to conform with all governing codes and ordinances. Follow details in the Installation Instructions section. ■ Install or store where it will not be exposed to temperatures below freezing or exposed to the weather . ■ Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload. ? ...

  • GE DBI.333 - page 4

    4 WHEN USING YOUR DRYER ■ Never reach into the dryer while the drum is moving. Before loading, unloading or adding clothes, wait until the drum has completely stopped. ■ Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room. DO NOT OPERA TE THE DR YER WITHOUT THE LINT FIL TER IN PLACE, UNLESS THE DR ...

  • GE DBI.333 - page 5

    WHEN NOT USING YOUR DRYER ■ Grasp the plug firmly when disconnecting this appliance to avoid damage to the cord while pulling. Place the cord away from traffic areas so it will not be stepped on, tripped over or subjected to damage. ■ Do not attempt to repair or replace any part of this appliance or attempt any servicing unless specifically rec ...

  • GE DBI.333 - page 6

    6 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions About the control panel. Y ou can locate your model number on the label on the front of the left side of the door opening. Model DCL333 Model DBL333 2 3 1 Model DVL 223 2 3 2 3 ...

  • GE DBI.333 - page 7

    IMPORT ANT : Clean the lint filter each time you use the dryer . T emperature REGULAR For regular to heavy cottons. MEDIUM For synthetics, blends, delicates and items labeled permanent press. FLUFF For fluffing items without heat. Use the TIMED DRY cycle. NO HEA T Automatic cycles automatically determine fabric dryness. Select LESS DRY if you want ...

  • GE DBI.333 - page 8

    8 The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer . The fabric may then be washed and dried normally . Damage to your dryer caused by these products is not covered by yo ...

  • GE DBI.333 - page 9

    9 Machine wash cycle Normal Permanent Press/ wrinkle resistant Gentle/ delicate Hand wash Do not wash Do not wring Water temperature Hot (50 ° C/120 ° F) Warm (40 ° C/105 ° F) Cold/cool (30 ° C/85 ° F) Tumble dry Dry Normal Permanent Press/ wrinkle resistant Gentle/ delicate Do not tumble dry Do not dry (used with do not wash) Heat setting Hi ...

  • GE DBI.333 - page 10

    Using the four shipping carton corner posts as padding (two on each side), carefully lay the dryer on its left side and remove foam shipping pad. CAUTION: T o prevent damage, do not use the control panel as a means to pick up or move the dryer . Return the dryer to an upright position. Adjust the leveling legs to match the washer height. The dryer ...

  • GE DBI.333 - page 11

    11 Electrical Connection Information for Gas Dryers WARNING— T o reduce the risk of fire, electric shock, or personal injury: • DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE. • DO NOT , UNDER ANY CIRCUMST ANCES, CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD. This dryer must be electrically grounded in accor ...

  • GE DBI.333 - page 12

    If all rigid metal duct cannot be used, then flexible all-metal venting can be used, but it will reduce the maximum recommended duct length. In special installations when it is impossible to make a connection with the above recommendations, then UL-listed clothes dryer transition duct may be used as transition venting between the dryer and wall con ...

  • GE DBI.333 - page 13

    Replace brass connecting pipe that is not plastic-coated. Stainless steel or plastic-coated brass MUST be used. WARNING: Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal injury . Always use NEW flexible connectors when installing a gas appliance. Installation MUST conform with local codes, or ...

  • GE DBI.333 - page 14

    14 Do Not Install the Dryer: Do not install the dryer in an area exposed to dripping water or outside weather conditions. Do not install the dryer in an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and ventilation air . Do not install the dryer on carpet. Floor MUST be solid with a ...

  • GE DBI.333 - page 15

    15 Rough-In Dimensions Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 ″ (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. If dryer is exhausted through the floor , the exhaust system MUST NOT terminate beneath the mobil ...

  • GE DBI.333 - page 16

    16 DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. Grounding must be in accordance with local codes and ordinances, or in the absence of local codes, in accordance with the National Electri ...

  • GE DBI.333 - page 17

    Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner . Install a UL-approved strain relief into the power cord entry hole of the mounting bracket. Use a strain relief which attaches to the mounting bracket with a nut. Finger -tighten the nut only at this time ...

  • GE DBI.333 - page 18

    18 Remove the shipping cap from gas pipe at the rear of the dryer . NOTE: DO NOT connect the dryer to LP gas ser vice without converting the gas valve. An LP conversion kit (Pub. No. 14-A038) MUST be installed by a qualified gas technician. Connect a 1/2 ″ (1.27 cm) I.D. semi-rigid or approved pipe from gas supply line to the 3/8 ″ (0.96 cm) pi ...

  • GE DBI.333 - page 19

    19 Reversing the Dryer Door Swing Open the dryer door . Remove the 4 hinge hole plugs or screws from the left side of door opening. Place nearby for future installation. NOTE: Y ou may need a plastic knife to help pull out the plugs. Be careful not to scratch the paint. Remove the four screws that secure the door hinges to the dryer front panel. NO ...

  • GE DBI.333 - page 20

    Problem Possible Causes What T o Do Dryer doesn’t start Dr yer is unplugged • Make sure the dryer plug is pushed completely into the outlet. Fuse is blown/circuit breaker • Check the household Distribution Panel fuse/circuit is tripped breaker box in your home, and replace fuse or reset breaker . NOTE: Electric dryers use two fuses or breaker ...

  • GE DBI.333 - page 21

    21 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions GEAppliances.com Problem Possible Causes What T o Do Inconsistent T ype of heat • Automatic drying times will var y according to the type drying times of heat used (electric, natural or LP gas), size of load, types of fabrics, wetness o ...

  • GE DBI.333 - page 22

    22 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions Notes. ...

  • GE DBI.333 - page 23

    23 For The Period Of: GE Will Replace: One Y ear Any part of the dryer which fails due to a defect in materials or workmanship. During this From the date of the full one-year warranty , GE will also provide, free of charge, all labor and in-home ser vice to original purchase replace the defective part. ■ Ser vice trips to your home to teach you h ...

  • GE DBI.333 - page 24

    Printed in the United States Consumer Support. GE Appliances W ebsite GEAppliances.com Have a question or need assistance with your appliance? T r y the GE Appliances W ebsite 24 hours a day , any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals, order parts, catalogs, or even schedule service on-l ...

Manufacturer GE Category Clothes Dryer

Documents that we receive from a manufacturer of a GE DBI.333 can be divided into several groups. They are, among others:
- GE technical drawings
- DBI.333 manuals
- GE product data sheets
- information booklets
- or energy labels GE DBI.333
All of them are important, but the most important information from the point of view of use of the device are in the user manual GE DBI.333.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals GE DBI.333, service manual, brief instructions and user manuals GE DBI.333. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product GE DBI.333.

Similar manuals

A complete manual for the device GE DBI.333, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use GE DBI.333 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of GE DBI.333.

A complete GE manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual GE DBI.333 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the GE DBI.333, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the GE DBI.333, that we can find in the current document
3. Tips how to use the basic functions of the device GE DBI.333 - which should help us in our first steps of using GE DBI.333
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with GE DBI.333
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of GE DBI.333 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning GE DBI.333?

Use the form below

If you did not solve your problem by using a manual GE DBI.333, ask a question using the form below. If a user had a similar problem with GE DBI.333 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)