English dropdown-ico

Manual D-Link TM DES-6500

334 pages 8.88 mb
Download

Go to site of 334

Summary
  • D-Link TM DES-6500 - page 1

    Product Model : TM DES-6500 Modular Layer 3 Chassis Ethernet Switch Release 3 CLI Manual ...

  • D-Link TM DES-6500 - page 2

    Table of Contents Introductio n ............................................................................................................................................ 1 Using the Con sole CLI .......................................................................................................... ................... 4 Command Syntax ........ ...

  • D-Link TM DES-6500 - page 3

    DVMRP Command s ................................................................................................................. ............ 290 PIM Comma nds ................................................................................................................................... 295 IP Multicasti ng Command s .......................... ...

  • D-Link TM DES-6500 - page 4

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 1 I NTRODUCTION The xStack DES-6500 layer 3 modular chassis Ethernet switch is a m ember of the D-Link xStack fam ily. Ranging from 10/100Mbps edge switches to core gigabi t switches, the xStack switch family has been future-proof designed to provide a stacking architecture with fau ...

  • D-Link TM DES-6500 - page 5

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual There is no initial username or passwo rd. Just press the Enter key twice to display the CLI input cursor − DE S-6500:4# . This is the comm and line where all comm ands are input. Setting the Switch’s IP Address Each switch must be assigned its own IP Address, which is us ed for ...

  • D-Link TM DES-6500 - page 6

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Figure 1-3. Assigning an IP Address In the above example, t he Switch was assigned an IP address of 10.53.13.144 with a subnet m ask of 255.0.0.0. The system message Success indicates t hat the command was execut ed successfully. The Switch can now be configured and m anaged via Tel ...

  • D-Link TM DES-6500 - page 7

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 2 U SING THE C ONSOLE CLI The XStack DES-6500 supports a console management interface that allows the user to connect to the Switch’s m anagement agent via a serial port and a term inal or a comput er running a terminal em ulation program. The consol e can also be used over th e n ...

  • D-Link TM DES-6500 - page 8

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Figure 2-1. Initial Console Screen Comm ands are entered at the comm and prompts, DE S-6500:4# . There are a number of helpful features included in the CLI. Entering the ? command will display a list of all of the top-level co mmand s. Figure 2-2. The ? Command When entering a comma ...

  • D-Link TM DES-6500 - page 9

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Figure 2-3. Example Command Parameter Help In this case, the comma nd config account was entered with the parameter <username> . The CLI will then prompt to enter the <username> with th e message, Next possible completions: . Every comm and in the CLI has this feature, a ...

  • D-Link TM DES-6500 - page 10

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual If a comma nd is entered that is unrecognized by the CL I, the top-level commands will be displayed under the Available commands: prompt. Figure 2-5. The Available Commands Prompt The top-level com mands consist of com mands such as show or config . Most of t hese commands requi re ...

  • D-Link TM DES-6500 - page 11

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 3 C OMM AND S YNT AX The following sy mbols are used to describe how com mand entries are m ade and values and arguments are specified in this manual. The online help contained in the CLI and available through the console interface uses the sam e syntax. Note : All commands are case ...

  • D-Link TM DES-6500 - page 12

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual {braces} Purpose Encloses an optional value or set of optional arguments. Syntax reset {[config | system]} Description In the above syntax exampl e, you have the option to specify config or sy stem . It is not necessary to specify either optional value, however the effect of the sys ...

  • D-Link TM DES-6500 - page 13

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 4 B ASIC S WITCH C OMM ANDS The basic switch comma nds in the Command Line Interface (CLI) are listed (along with the appropriate param eters) in the following table. Command Parameters create account [admin | user] <username 15> config account <username 15> show account ...

  • D-Link TM DES-6500 - page 14

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create account Purpose Used to create user accounts. Syntax create [admin | user] <username 15> Description The create account command is used to create user accounts that consist of a username of 1 to 15 characters and a password of 0 to 15 characters. Up to 8 user accounts c ...

  • D-Link TM DES-6500 - page 15

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config account dlink Command: config account dlink Enter a old passw ord:**** Enter a case-sensitive new passw ord:**** Enter the new passw ord again for confirmation:**** Success. DES-6500:4# show account Purpose Used to display user accounts. Syntax show account Descrip ...

  • D-Link TM DES-6500 - page 16

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#delete account System Command: delete account System Are you sure to delete the last administrator account?(y /n)y Success. DES-6500:4# Example usage: To delete the user account “System 2”: DES-6500:4#delete account System2 Command: delete account System2 Success. DES ...

  • D-Link TM DES-6500 - page 17

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command: show config config_in_NVRAM #------------------------------------------------------------------------------------------------------ # DES-6500 Configuration # # Firmw are: Build 3.00-B29 # Copyright(C) 2004- 2007 D-Link Corporation. All rights reserved. #------------------- ...

  • D-Link TM DES-6500 - page 18

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show switch Purpose Used to display information about the Switch. Syntax show sw itch Description This command displays information about the Switch. Parameters None. Restrictions None. Example usage: To display the Switch information: DES-6500:4#show sw itch Command: show sw itch D ...

  • D-Link TM DES-6500 - page 19

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show device_status Purpose Used to display the current st atus of the hardware of the Switch. Syntax show device_status Description This command displays the curr ent status of the Switch’s physical elements. Parameters None. Restrictions None. Example usage: To show the current h ...

  • D-Link TM DES-6500 - page 20

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config serial_port Purpose Used to configure the serial port. Syntax config serial_port {auto_logout [never | 2_minutes | 5_minutes | 10_minutes | 15_minutes]} Description This command is used to configure the serial port’s baud rate and auto logout settings. Parameters auto_logou ...

  • D-Link TM DES-6500 - page 21

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#enable clipaging Command: enable clipaging Success. DES-6500:4# disable clipaging Purpose Used to disable the pausing of the console screen scrolling at the end of each page when the show command displays more than one screen of information. Syntax disable clipaging Descr ...

  • D-Link TM DES-6500 - page 22

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual disable telnet Purpose Used to disable the Telnet protocol on the Switch. Syntax disable telnet Description This command is used to disable the Telnet protocol on the Switch. Parameters None. Restrictions Only administrator-lev el users can issue this command. Example usage: To disa ...

  • D-Link TM DES-6500 - page 23

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual disable web Purpose Used to disable the HTTP-based management software on the Switch. Syntax disable w eb Description This command disables the Web-based management software on the Switch. Parameters None. Restrictions Only administrator-lev el users can issue this command. Example ...

  • D-Link TM DES-6500 - page 24

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual reboot Purpose Used to restart the Switch. Syntax reboot Description This command is used to restart the Switch. Parameters None. Restrictions None. Example usage: To restart the Switch: DES-6500:4#reboot Command: reboot Are you sure want to proceed w ith the system reboot? (y/n) Pl ...

  • D-Link TM DES-6500 - page 25

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual login Purpose Used to log in a user to the Switch’s console. Syntax login Description This command is used to initiate the login procedure. The user will be prompted for his Username and Password. Parameters None. Restrictions None. Example usage: To initiate the login p rocedure: ...

  • D-Link TM DES-6500 - page 26

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config command_prompt Switch. default – Entering this parameter will return the command prompt to its original factory default setting. Restrictions The reset command will not alter the configured command prompt, yet the reset system command will return the command prompt to its o ...

  • D-Link TM DES-6500 - page 27

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config greeting_message Command: config greeting_message Greeting Messages Editor =============================================================================== DES-6500 Chassis Ethernet Sw itch Command Line Interface Firmw are: Build 3.00-B29 Copyright(C) 2004-2007 D-Li ...

  • D-Link TM DES-6500 - page 28

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 5 S WITCH P OR T C OMM ANDS The switch port commands in the Com mand Line Interface (CLI) ar e listed (along with the appropriate parameters) in the following table. Command Parameters config ports [<portlist> | all] {speed [auto | 10_half | 10_full | 100_half | 100_full | 100 ...

  • D-Link TM DES-6500 - page 29

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ports from the maste r . If one connection is set for 1000 master , the other side of the connection must be set for 1000 slave . Any other configuration will result in a link down status for both ports. None denotes the Switch will serve no role for stacking. flow_control [e ...

  • D-Link TM DES-6500 - page 30

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show ports Command: show ports Port Port Settings Connection Address State Sp eed/Duplex/Flow Ctrl Speed/Duplex/Flow Ctrl Learning ------ -------- --------------------- --------------------- -------- 1:1 Enabled Auto/Enabled Link Dow n Enabled 1:2 Enabled Auto/Enabled Lin ...

  • D-Link TM DES-6500 - page 31

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 6 P ORT S ECURITY C OM MANDS The port security comma nds in the Command Line Interface (CLI) are listed (along with the appropriate param eters) in the following table. Command Parameters config port_security ports [<portlist> | all] {admin_s tate [enabled | disabled] | max_le ...

  • D-Link TM DES-6500 - page 32

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To configur e the port security: DES-6500:4#config port_security ports 5:1-5:5 admin_state enabled max_learning_addr 5 lock_address_mode DeleteOnReset Command: config port_security ports 5:1-5:5 admin_state enabled max_learning_addr 5 lock_address_mode DeleteOnReset S ...

  • D-Link TM DES-6500 - page 33

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual delete port_security_entry _vlan_name Purpose Used to delete an entry from the Switch’s port secu rity settings. Syntax delete port_security_entry _vlan_name <v lan_name 32> port <port> mac_address <macaddr> Description This command is used to remove an entry fro ...

  • D-Link TM DES-6500 - page 34

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 7 N ETWORK M ANAGEMENT (SNMP) C OM MANDS The network managem ent commands in the Com mand Line Interface (CLI) are listed (along with the appropriate param eters) in the following table. The xStack DES-6500 support the Sim ple Network Manageme nt Protoc ol (SNMP) versions 1, 2c, and ...

  • D-Link TM DES-6500 - page 35

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command Parameters <view_name 32> | notify_view <view_name 32>} delete snmp group <groupname 32> show snmp groups create snmp host <ipaddr> {v1 |v2c | v3 [noauth_nopriv | auth_nopriv | auth_priv]} <auth_string 32> delete snmp host <ipaddr> <aut ...

  • D-Link TM DES-6500 - page 36

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create snmp user Encryption − Scrambles the contents of messages to prevent it from being viewed by an unauthorized source. Parameters <username 32> − An alphanumeric name of up to 32 characters that will identify the new SNMP user. <groupname 32> − An alphanumeric ...

  • D-Link TM DES-6500 - page 37

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create snmp user the agent.  • <priv_key 32-32> - Enter an alphanumeric key string of exactly 32 characters, in hex form, that will be used to encrypt the cont ents of messages the host sends to the agent. none – Adding this parameter will add no encryption. Restriction ...

  • D-Link TM DES-6500 - page 38

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show snmp user Purpose Used to display information about each SNMP username in the SNMP group username table. Syntax show snmp user Description The show snmp user command displays information about each SNMP username in the SNMP group username table. Parameters None. Restrictions On ...

  • D-Link TM DES-6500 - page 39

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#create snmp view dlinkview 1.3.6 view _type included Command: create snmp view dlinkview 1.3.6 view _type included Success. DES-6500:4# delete snmp view Purpose Used to remove an SNMP vi ew entry previously created on the Switch. Syntax delete snmp view <view _name 32& ...

  • D-Link TM DES-6500 - page 40

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command: show snmp view Vacm View Table Settings View Name Subtree View Type -------------------- ------------------------- ---------- ReadView 1 Included WriteView 1 Included NotifyView 1.3.6 Included restricted 1.3.6.1.2.1.1 Included restricted 1.3.6.1.2.1.11 Included restricted 1 ...

  • D-Link TM DES-6500 - page 41

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To create the SNMP community string “dlink:” DES-6500:4#create snmp community dlink v iew ReadView read_w rite Command: create snmp community dlink v iew ReadView read_w rite Success. DES-6500:4# delete snmp community Purpose Used to remove a specific SNMP communi ...

  • D-Link TM DES-6500 - page 42

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To display the currently entered SNMP community strings: DES-6500:4#show snmp community Command: show snmp community SNMP Community Table Community Name View Name Access Right ------------------------------ ------------------------------ ------------ dlink ReadView re ...

  • D-Link TM DES-6500 - page 43

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To display the current nam e of the SNMP engine on the Switc h: DES-6500:4#show snmp engineID Command: show snmp engineID SNMP Engine ID : 0035636666 DES-6500:4# create snmp group Purpose Used to create a new SNMP gr oup, or a table that maps SNMP users to SNMP views. Syntax create ...

  • D-Link TM DES-6500 - page 44

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create snmp group be encrypted. read_view – Specifies that the SNMP group being created can request SNMP messages. write_view – Specifies that the SNMP group being created has write privileges. <view_name 32> − An alphanumeric string of up to 32 characters that is used t ...

  • D-Link TM DES-6500 - page 45

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show snmp groups Purpose Used to display the group- names of SNMP groups currently configured on the Switch. The securi ty model, level, and status of each group are also displayed. Syntax show snmp groups Description The show snmp groups command displays the group-names of SNMP gro ...

  • D-Link TM DES-6500 - page 46

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual ReadView Name : restricted WriteView Name : Notify View Name : restricted Security Model : SNMPv 3 Security Lev el : NoAuthNoPriv Group Name : ReadGroup ReadView Name : CommunityView WriteView Name : Notify View Name : CommunityView Security Model : SNMPv 1 Security Lev el : NoAuthN ...

  • D-Link TM DES-6500 - page 47

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create snmp host of Management Information (SMI) and adds some security features. v3 – Specifies that the SNMP ve rsion 3 will be used. SNMP v3 provides secure access to devices through a combination of authentication and encrypting packe ts over the network. SNMP v3 adds:   ...

  • D-Link TM DES-6500 - page 48

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To delete an SNMP host entry: DES-6500:4#delete snmp host 10.48.74.100 public Command: delete snmp host 10.48.74.100 public Success. DES-6500:4# show snmp host Purpose Used to display the recipi ent of SNMP traps generated by the Switch’s SNMP agent. Syntax show snm ...

  • D-Link TM DES-6500 - page 49

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create trusted_host Parameters <ipaddr> − The IP address of the trusted host. Restrictions Only administrator-lev el users can issue this command. Example usage: To create the trusted host: DES-6500:4#create trusted_host 10.48.74.121 Command: create trusted_host 10.48.74.121 ...

  • D-Link TM DES-6500 - page 50

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example Usage: To delete a trusted host with an IP address 10.48.74.121: DES-6500:4#delete trusted_host 10.48.74.121 Command: delete trusted_host 10.48.74.121 Success. DES-6500:4# enable snmp traps Purpose Used to enable SNMP trap support. Syntax enable snmp traps Description The en ...

  • D-Link TM DES-6500 - page 51

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show snmp traps Purpose Used to show SNMP trap support on the Switch . Syntax show snmp traps Description This command is used to view the SNMP trap support status currently configured on the Switch. Parameters None. Restrictions Only administrator-lev el users can issue this comman ...

  • D-Link TM DES-6500 - page 52

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example Usage: To disable the SNMP authenticat ion trap support: DES-6500:4#disable snmp authenticate_traps Command: disable snmp authenticate_traps Success. DES-6500:4# config snmp system_contact Purpose Used to enter the name of a c ontact person who is responsible for the Switch. ...

  • D-Link TM DES-6500 - page 53

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To configure the Switch locati on for “ HQ 5F ”: DES-6500:4#config snmp system_location HQ 5F Command: config snmp system_location HQ 5F Success. DES-6500:4# config snmp system_name Purpose Used to configure the name for the Switch. Syntax config snmp system_name {<sw_name> ...

  • D-Link TM DES-6500 - page 54

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#enable rmon Command: enable rmon Success. DES-6500:4# disable rmon Purpose Used to disable RMON on the Switch. Syntax disable rmon Description This command is used, in conjunction with the enable rmon command above, to enable and disable remote monitoring (RMON) on the Sw ...

  • D-Link TM DES-6500 - page 55

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 8 S WITCH U TILITY C OMM ANDS The switch utility commands in the Com mand Li ne Interface (CLI) are listed (along with the appropriate param eters) in the following table. Parameters [firmware_fromTFTP <ipaddr> <path_filename 64> unit [all_line_card | cpu | <unitid 1- ...

  • D-Link TM DES-6500 - page 56

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual download  increment − Allows the download of a partial switch configuration file. This allows a file to be downloaded that will change only the Switch parameter s explicitly stated in the configuration file. All other switch parameters will remain unchanged. Restrictions The TF ...

  • D-Link TM DES-6500 - page 57

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#upload cfg_toTFTP 10.48.74.121 c:cfglog.txt Command: upload cfg_to TFTP 10.48.74.121 c:cfglog.txt Connecting to server................... Done. Upload confi guration...................Done. DES-6500:4# ping Purpose Used to test the connec tivity between network device ...

  • D-Link TM DES-6500 - page 58

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual traceroute Parameters <ipaddr> - Specifies the IP address of the host. ttl <value 1-60> - The time to live value of the trace route request. This is the maximum number of routers the traceroute command will cross while seeking the network path between two devices. port & ...

  • D-Link TM DES-6500 - page 59

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual NOTE: Dual-purpose (DHCP/TFTP) server utilit y software may require entry of the configuration file name and path within the user interface. Alternatively, the DHCP software may require creating a separate ext file with the configuration file name and path in a specific directory on ...

  • D-Link TM DES-6500 - page 60

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual disable autoconfig Purpose Use this to deactivate autoconfiguration from DHCP. Syntax disable autoconfig Description This instructs the Switch not to accept autoconfiguration instruction from the DHCP server. This does not change t he IP settings of the Switch. The ipif settings wil ...

  • D-Link TM DES-6500 - page 61

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 9 N ETWORK M ONIT ORING C OMMANDS The network monitoring commands in the Command Line Interface (C LI) are listed (along with the appropriate parameters) in the following table. Command Parameters show packet ports <portlist> show error ports <portlist> show utilization ...

  • D-Link TM DES-6500 - page 62

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show packet ports Parameters <portlist> − Specifies a range of ports to be displayed. The port list is specified by listing the lo west slot number and the beginning port number on that slot, separated by a colon. Then the highest slot number, and the highest port number of ...

  • D-Link TM DES-6500 - page 63

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To display the errors of the port 3 of module 1: DES-6500:4#show errors ports 1:3 Command: show errors ports 1:3 RX Frames TX Frames --------------- ---------------- CRC Error 19 Excessive Deferral 0 Undersize 0 CRC Error 0 Oversize 0 Late Collision 0 Fragment 0 Exces ...

  • D-Link TM DES-6500 - page 64

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show utilization ports Command: show utilization ports Port TX/sec RX/sec Util Port TX/sec RX/sec Util ---- ---------- ---------- ---- ---- ---------- ---------- ---- 1:1 0 0 0 2:10 0 0 0 1:2 0 0 0 2:11 0 0 0 1:3 0 0 0 2:12 0 0 0 1:4 0 0 0 3:1 0 0 0 1:5 0 0 0 3:2 0 0 0 1: ...

  • D-Link TM DES-6500 - page 65

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show stack_information Command: show stack_information Box Prio- Prom Runtime H/W ID Type Exist rity version version version --- ----------- ----- ----- -------- -------- -------- 1 DES-6507 exist 16 2.00-B20 3.00-B29 1A1 2 USR-NOT-CFG no 3 USR-NOT-CFG no 4 USR-NOT-CFG no ...

  • D-Link TM DES-6500 - page 66

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual clear log Purpose Used to clear the Switch’s history log. Syntax clear log Description This command will clear the Switch’s history log. Parameters None. Restrictions Only administrator-lev el users can issue this command. Example usage: To clear the log information: DES-6500:4# ...

  • D-Link TM DES-6500 - page 67

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual enable syslog Purpose Used to enable the system log to be sent to a remote host. Syntax enable syslog Description The enable syslog command enables the system log to be sent to a remote host. Parameters None. Restrictions Only administrator-lev el users can issue this command. Examp ...

  • D-Link TM DES-6500 - page 68

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show syslog Purpose Used to display the syslog protocol status as enabled or disabled. Syntax show syslog Description The show syslog command displays the syslog status as enabled or disabled. Parameters None. Restrictions None. Example usage: To display the current stat us of the s ...

  • D-Link TM DES-6500 - page 69

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create syslog host facility − Some of the operating syst em daemons and processes have been assigned Facility values. Processes and daemons that have not been explicitly assigned a Facility ma y use any of the "local use" facilities or they may use the "user-l evel& ...

  • D-Link TM DES-6500 - page 70

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create syslog host where syslog messages will be sent. state [enabled | disabled] − Allows the sending of syslog messages to the remote host, specified above, to be enabled and disabled. Restrictions Only administrator-lev el users can issue this command. Example usage: To create ...

  • D-Link TM DES-6500 - page 71

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config syslog host warning − Specifies that warning messages will be sent to the remote host. This corresponds to number 4 from the list above. all − Specifies that all of the cu rrently supported syslog messages that are generated by the Switch will be sent to the remote host. ...

  • D-Link TM DES-6500 - page 72

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config syslog host remote host. This corresponds to number 23 from the list above. udp_port <udp_port_number> − Specifies the UDP port number that the syslog protocol will use to send messages to the remote host. ipaddress <ipaddr> − Specifies the IP address of the r ...

  • D-Link TM DES-6500 - page 73

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config syslog host all severity − Severity level indicator, as described below: Bold font indicates that the corresponding severity level is currently supported on the Switch. Numerical Severity Code 0 Emergency: system is unusable 1 Alert: action must be taken immediately 2 Criti ...

  • D-Link TM DES-6500 - page 74

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config syslog host all local0 − Specifies that local use 0 messages will be sent to the remote host. This corresponds to number 16 from the list above. local1 − Specifies that local use 1 messages will be sent to the remote host. This corresponds to number 17 from the list above ...

  • D-Link TM DES-6500 - page 75

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual delete syslog host Purpose Used to remove a sysl og host, that has been previously configured, from the Switch. Syntax delete syslog host [<index 1-4> | all] Description The delete syslog host command is used to remove a syslog host that has been previously configured from the ...

  • D-Link TM DES-6500 - page 76

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config system_severity Purpose To configure when and wher e severity messages are to be recorded. Syntax config system_sev erity [trap | log | all] [critical | warning | information] Description This command is used to confi gure the system severity levels on the Switch. When an eve ...

  • D-Link TM DES-6500 - page 77

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config system_sev erity trap critical Command: config system_sev erity trap critical Success. DES-6500:4# show system_severity Purpose To display the current severity settings set on the Switch. Syntax show system_severity Description This command is used to view the seve ...

  • D-Link TM DES-6500 - page 78

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 10 M UL TIPLE S P ANNING T REE P ROT OCOL (MSTP) C OM MANDS This switch supports three versions of the Spanning Tree Pr otocol; 802.1d STP, 802.1w Rapid STP and 802.1s MSTP. Multiple Spanning Tree Protocol, or MSTP, is a sta ndard defined by the IEEE comm unity that allows multiple ...

  • D-Link TM DES-6500 - page 79

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command Parameters config stp priority <value 0-61440> instance_id <value 0-15> config stp mst_config_id {revision_level <int 0-65535> | name <string>} config stp mst_ports <portlis t> instance_id <value 0-15> {i nternalCost [auto | value 1- 20000 ...

  • D-Link TM DES-6500 - page 80

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#disable stp Command: disable stp Success. DES-6500:4# config stp version Purpose Used to globally set the version of STP on the Switch. Syntax config stp version [mstp | rstp | stp] Description This command allows the us er to choose the version of the spanning tree to be ...

  • D-Link TM DES-6500 - page 81

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config stp values consistent with other devices on the bridged LAN. If the value ages out and a BPDU has still not been received from the Root Bridge, the Switch will start sending its own BPDU to all other switches for permission to become the Root Bridge. If it turns out that your ...

  • D-Link TM DES-6500 - page 82

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config stp maxage 18 maxhops 15 Command: config stp maxage 18 maxhops 15 Success. DES-6500:4# config stp ports Purpose Used to setup STP on the port level. Syntax config stp ports <portlist> {externalCost [auto | <value 1- 200000000>] | hellotime <value 1-1 ...

  • D-Link TM DES-6500 - page 83

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config stp ports stations or segments that are capable of being upgraded to 802.1w RSTP or 802.1s MSTP on all or some portion of the segment. edge [true | false] – true designates the port as an edge port. Edge ports cannot create loops, however an edge port can lose edge port sta ...

  • D-Link TM DES-6500 - page 84

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To create a spanning tree instance 2: DES-6500:4#create stp instance_id 2 Command: create stp instance_id 2 Success. DES-6500:4# config stp instance_id Purpose Used to add or delete an STP instance ID. Syntax config stp instance_id <value 1-15> [add_vlan | remov ...

  • D-Link TM DES-6500 - page 85

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config stp instance_id 2 remove_vlan 10 Command : config stp instance_id 2 remove_vlan 10 Success. DES-6500:4# delete stp instance_id Purpose Used to delete a STP in stance ID from the Switch. Syntax delete stp instance_id <value 1-15> Description This command allow ...

  • D-Link TM DES-6500 - page 86

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To set the priority value fo r instance_id 2 as 4096: DES-6500:4#config stp priority 4096 instance_id 2 Command : config stp priority 4096 instance_id 2 Success. DES-6500:4# config stp mst_config_id Purpose Used to update the MSTP configuration identification. Syntax ...

  • D-Link TM DES-6500 - page 87

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config stp mst_ports higher priority value for interfaces to be selected for forwarding first. In instances where the priori ty value is identical, the MSTP function will implement the lowest port number into the forwarding state and other interfaces will be blocked. Remember that l ...

  • D-Link TM DES-6500 - page 88

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show stp Purpose Used to display the Switch ’s current STP configuration. Syntax show stp Description This command displays the Sw itch’s current STP configuration. Parameters None. Restrictions None. Example usage: To display the status of STP on t he Switch: Status 1: STP enab ...

  • D-Link TM DES-6500 - page 89

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Max Age : 20 TX Hold Count : 3 Forw arding BPDU : Enabled Loopback Detection : Enabled LBD Recover Time : 60 DES-6500:4# show stp ports Purpose Used to display the Switch’s current instance_id configuration. Syntax show stp ports <portlist> Description This command displays ...

  • D-Link TM DES-6500 - page 90

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show stp instance_id configuration for the CIST internally set on the Switch. Restrictions None. Example usage: To display the STP instance con figuration for in stance 0 (the internal CIST) on the Switch: DES-6500:4#show stp instance_id 0 Command: show stp instance_id 0 STP Instanc ...

  • D-Link TM DES-6500 - page 91

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show stp mst_config_id Command: show stp mst_config_id Current MST Configuration Identification ---------------------------------------- Configuration Name : 00:53:13:1A:33:24 Revision Level :0 MSTI ID Vid list ------- ----------- CIST 2-4094 1 1 DES-6500:4# 88 ...

  • D-Link TM DES-6500 - page 92

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 11 F ORW ARDING D A T ABASE C OMM ANDS The forwarding database comma nds in the Command Line Interface (CLI) are listed (along with the appropriate param eters) in the following table. Command Parameters create fdb <vlan_name 32> <macaddr> port <port> create multic ...

  • D-Link TM DES-6500 - page 93

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#create fdb default 00-00-00-00-01-02 port 2:5 Command: create fdb default 00-00-00-00-01-02 port 2:5 Success. DES-6500:4# create multicast_fdb Purpose Used to create a static ent ry to the multicast MAC address forwarding table (database) Syntax create multicast_fdb <v ...

  • D-Link TM DES-6500 - page 94

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config multicast_fdb  <portlist> − Specifies a range of ports to be displayed the beginning port number on that slot, separated by a colon. Then the highest slot number, and the highest port number of the range (also separated by a colon) are specified. The beginning and ...

  • D-Link TM DES-6500 - page 95

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config fdb aging_time Purpose Used to set the aging time of the forwarding database. Syntax config fdb aging_time <sec 10-1000000> Description The aging time affects the learning process of the Switch. Dynamic forwarding table entries, which are made up of the source MAC addre ...

  • D-Link TM DES-6500 - page 96

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#delete fdb default 00-00-00-00-01-02 Command: delete fdb default 00-00-00-00-01-02 Success. DES-6500:4# Example usage: To delete a multicast fdb entry: DES-6500:4#delete fdb default 01-00-00-00-01-02 Command: delete fdb default 01-00-00-00-01-02 Success. DES-6500:4# clear ...

  • D-Link TM DES-6500 - page 97

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show multicast_fdb Purpose Used to display the contents of the Switch’s multicast forwarding database. Syntax show mulitcast_fdb [vlan <vlan_name 32> | mac_address <macaddr>] Description This command is used to display the current contents of the Switch’s multicast M ...

  • D-Link TM DES-6500 - page 98

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To display unicast M AC address table: DES-6500:4#show fdb Command: show fdb Unicast MAC Address Aging Time = 300 VID VLAN Name MAC Address Port Type ---- ---------------- ----------------- ------ ---------------- 1 default 00-00-39- 34-66-9A 1:12 Dynamic 1 default 00 ...

  • D-Link TM DES-6500 - page 99

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show ipfdb Command: show ipfdb Interface IP Address Port Learned ------------ --------------- ------ ------------ System 10.0.0.1 1:13 Dy namic System 10.0.0.2 1:13 Dy namic System 10.0.0.3 1:13 Dy namic System 10.0.0.4 1:13 Dy namic System 10.0.0.7 1:13 Dy namic System 1 ...

  • D-Link TM DES-6500 - page 100

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 12 B ROADCAST S TOR M C ONTROL C OMM ANDS On a computer network, packets such as Multicast packets and B roadcast packets continually flood the net work as normal procedure. At times, t his traffic may i ncrease do to a malicious endsta tion on the network or a malfunctioning device ...

  • D-Link TM DES-6500 - page 101

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config traffic control latter of which will now provide shutdown, recovery and trap notification functions for the Switch. Parameters <portlist> − Used to specify a range of ports to be configured for traffic control. This is specified by listing the lowest switch number and ...

  • D-Link TM DES-6500 - page 102

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config traffic control and the port is still experienci ng packet storms, the port will be placed in shutdown forever mode and can only be manually recovered using the config traffic control_recover command. time_interval - The Interval will set the time between Multicast and Broadc ...

  • D-Link TM DES-6500 - page 103

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4# config traffic control_recover 1:1-1:5 Command: config traffic control_recover 1:1-1:5 Success. DES-6500:4# config traffic control_trap Purpose Used to configure the trap se ttings for the packet storm control mechanism. Syntax config traffic control_trap [none | storm_o ...

  • D-Link TM DES-6500 - page 104

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show traffic control traffic control settings. This is s pec ified by listing the lowest switch number and the beginning port number on that switch, separated by a colon. Then the highest switch number, and the highest port number of the range (also separated by a colon) are specifi ...

  • D-Link TM DES-6500 - page 105

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 13 Q O S C OMM ANDS The xStack DES-6500 supports 802.1p priority queuing. This switc h has eight classes of service for each port on the Switch, one of which is internal and not configurable to the user. Th ese hardware classes of service are num bered from 6 (Class 6) — the highe ...

  • D-Link TM DES-6500 - page 106

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command Parameters config bandwidth_control [<por tlist> | all] {rx_rate [no_limit | <value 1-9999>] | tx_rate [no_limit <value 1-9999>]} show bandwidth_control {<portlist>} config scheduling <class_id 0-6> {max_packet <value 0-15>} show schedulin ...

  • D-Link TM DES-6500 - page 107

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config bandwidth_control  <value 1-9999> − Specifies the packet limit, in Mbps, that the above ports will be allowed to transmit. Restrictions Only administrator-lev el users can issue this command. Example usage: To configure bandwidth control: DES-6500:4#config bandw id ...

  • D-Link TM DES-6500 - page 108

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show bandw idth_control 1:1-1:10 Command: show bandw idth_control 1:1-1:10 Bandw idth Control Table Port RX Rate (Mbit/sec) TX_RATE (Mbit/sec) ---- ------------------------ ---------------------- 1:1 no_limit 10 1:2 no_limit 10 1:3 no_limit 10 1:4 no_limit 10 1:5 no_limit ...

  • D-Link TM DES-6500 - page 109

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config scheduling combination of strict and we ight-fair (weighted round-robin “ WRR ” ) scheduling. Priority classes that have a 0 in the max_packet field will forward packets with strict priority scheduling. The remaining classes, that do not have a 0 in their max_packet field ...

  • D-Link TM DES-6500 - page 110

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show scheduling Purpose Used to display the currently configured traffic scheduling on the Switch. Syntax show scheduling Description The show scheduling command displays the current configuration for the maximum number of packets ( max_packets ) assigned to the seven hardware prior ...

  • D-Link TM DES-6500 - page 111

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config 802.1p user_priority 4 4 5 5 6 6 7 6 Parameters <priority 0-7> − Specifies which of the ei ght 802.1p priority tags (0 through 7) to map to one of the Switch’s hardware priority classes of service ( <class_id> , 0 through 6). <class_id 0-6> − Specifies ...

  • D-Link TM DES-6500 - page 112

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config 802.1p default_priority Purpose Used to specify default prio rity settings on the Switch. Untagged packets that are received by the Sw itch will be assigned a priority tag in its priority field using this command. Syntax config 802.1p default_priority [< portlist> | all ...

  • D-Link TM DES-6500 - page 113

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To display the current 802.1p defaul t priority configurati on on the Switch: DES-6500:4# show 802.1p default_priority Command: show 802.1p default_priority Port Priority ------- ----------- 1:1 0 1:2 0 1:3 0 1:4 0 1:5 0 1:6 0 1:7 0 1:8 0 1:9 0 1:10 0 1:11 0 1:12 0 1: ...

  • D-Link TM DES-6500 - page 114

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config scheduling_mechanism Parameters strict – Entering the strict parameter indicates that the highest class of service is the first to be processed. That is, the highest class of service should finish emptying before the others begin. weight_fair – Entering the weight fair pa ...

  • D-Link TM DES-6500 - page 115

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual enable hol_prevention Purpose Used to enable HOL prevention. Syntax enable hol_prevention Description The enable hol_prevention command enables Head of Line prevention. Parameters None. Restrictions You must hav e administrator privileges. Example Usage: To enable HOL prevention: DE ...

  • D-Link TM DES-6500 - page 116

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show hol_prevention Purpose Used to show HOL prevention. Syntax show hol_prevention Description The show hol_prevention command displays the Head of Line prevention state. Parameters None. Restrictions None. Example Usage: To view the HOL prevention status: DES-6500:4#show hol_preve ...

  • D-Link TM DES-6500 - page 117

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 14 P ORT M IRRORING C OMMANDS The port mi rroring comma nds in the Command Line Interface (CLI) are listed (along with the appropriate param eters) in the following table. Command Parameters config mirror port <port> [add | delete] s ource ports <portlist> [rx | tx | bot ...

  • D-Link TM DES-6500 - page 118

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To add the mirrori ng ports: DES-6500:4# config mirror port 1:10 add source ports 1:1-1:5 both Command: config mirror port 1:10 add source ports 1:1-1:5 both Success. DES-6500:4# config mirror port delete Purpose Used to delete a port mirroring configuration. Syntax c ...

  • D-Link TM DES-6500 - page 119

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual enable mirror Purpose Used to enable a previously entered port mirroring configuration. Syntax enable mirror Description This command, combined with the disable mirror command below, allows you to enter a port mirroring configuration into the Switch, and then turn the port mirroring ...

  • D-Link TM DES-6500 - page 120

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show mirror Purpose Used to show the current port mirroring configuration on the Switch. Syntax show mirror Description This command displays the current port mirroring configuration on the Switch. Parameters None. Restrictions None. Example usage: To display m irroring configuratio ...

  • D-Link TM DES-6500 - page 121

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 15 VLAN C OMM ANDS The xStack DES-6500 incorporates protocol -based VLANs. This standard, defined by the IEEE 802.1v standard maps packets to protocol-defin ed VLANs by examining the type o ctet within th e packet header to discover the type of protocol associated with it. After ass ...

  • D-Link TM DES-6500 - page 122

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create vlan tag <vlanid 2-4094> − The VLAN ID of the VLAN to be created. Allowed values = 2-4094 type – This parameter uses the type field of the packet header to determine the packet protocol and destination VLAN. There are two main choices of types for VLANs created on t ...

  • D-Link TM DES-6500 - page 123

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create vlan information is defined by the Systems Network Architecture (SNA) 802.2 Protocol.          protocol–snaEthernet2 - Using this parameter will instruct the Switch to forward packets to this VLAN if the tag in the packet header is concurrent with ...

  • D-Link TM DES-6500 - page 124

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual NOTE: A specific protocol VLAN and a user defined protocol VLAN with the same encapsulation protocol c annot coexist and will result in a Fail! Message. (For example, if a user creates an Ethernet2 protocol VLAN, the user can not create a userDefined protocol VLAN with an Ethernet e ...

  • D-Link TM DES-6500 - page 125

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config vlan add Description This command allows the user to add ports to the port list of a previously configured VLAN. Addi tional ports may be specified as tagging, untagging, or forbidden. The default is to assign the ports as untagging. Parameters <vlan_name 32> − The na ...

  • D-Link TM DES-6500 - page 126

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config vlan delete specifies all of the ports between slot 1, port 3 and slot 2, port 4 − in numerical order. Restrictions Only administrator-lev el users can issue this command. Example usage: To delete ports 5-7 of m odule 2 of the VLAN v1: DES-6500:4#config vlan v 1 delete 2:5- ...

  • D-Link TM DES-6500 - page 127

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config gvrp 1:1-1:4 state enabled ingress_checking enabled acceptable_frame tagged_only pv id 2 Command: config gvrp 1:1-1:4 state enabled ingress_checking enabled acceptable_frame tagged_only pv id 2 Success. DES-6500:4# enable gvrp Purpose Used to enable GVRP on the Swi ...

  • D-Link TM DES-6500 - page 128

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show vlan Purpose Used to display the current VLAN configuration on the Switch. Syntax show vlan {<vlan_name 32>} Description This command displays summary information about each VLAN including the VLAN ID, VLAN name, the Tagging/Untagging status, and the Member/Non-member/For ...

  • D-Link TM DES-6500 - page 129

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show gvrp Purpose Used to display the GVRP st atus for a port list on the Switch. Syntax show gvrp {<portlist>} Description This command displays the GVRP status for a port list on the Switch. Parameters <portlist> − Specifies a range of ports for which the GVRP status ...

  • D-Link TM DES-6500 - page 130

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 16 L INK A GGREGA TION C OMMANDS The link aggregation comma nds in the Command Line Interface (CL I) are listed (along with the appropriate parameters) in the following table. Command Parameters create link_aggregation group_id <value 1-32> {type [lacp | static]} delete link_a ...

  • D-Link TM DES-6500 - page 131

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#create link_aggregation group_id 1 Command: create link_aggregation group_id 1 Success. DES-6500:4# delete link_aggregation group_id Purpose delete link_aggregation group_id <value 1-32> This command is used to delete a previously configured link aggregation group. ...

  • D-Link TM DES-6500 - page 132

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Parameters group _id <value 1-32> − Specifies the group ID. The Switch allows up to 32 link aggregation groups to be configured. The group number identifies each of the groups. master_port <port> − Master port ID. Specif ies which port (by port number) of the link ag ...

  • D-Link TM DES-6500 - page 133

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config link_aggregation algorithm Purpose Used to configure the link aggregation algorithm. Syntax config link_aggregation algorithm [mac_source | mac_destination | mac_source_dest | ip_source | ip_destination | ip_source_dest] Description This command configures to part of the pack ...

  • D-Link TM DES-6500 - page 134

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show link_aggregation Purpose Used to display the current link aggregation configuration on the Switch. Syntax show link_aggregation {group_id <value 1-32> | algorithm} Description This command will display t he current link aggregation configuration of the Switch. Parameters ...

  • D-Link TM DES-6500 - page 135

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config lacp_port Purpose Used to configure setti ngs for LACP compliant ports. Syntax config lacp_port <portlist> mode [active | passive] Description This command is used to configure ports that have been previously designated as LACP ports (see create link_aggregation). Param ...

  • D-Link TM DES-6500 - page 136

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show lacp_port Purpose Used to display current LACP port mode settings. Syntax show lacp_port {<portlist>} Description This command will display the LACP mode settings as they are currently configured. Parameters <portlist> - Specifies a range of ports that will be displ ...

  • D-Link TM DES-6500 - page 137

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 17 IP C OMM ANDS (I NCLUDING M UL TIPLE IP INTERF ACES PER VLAN ) Multiple IP interfaces per VLAN is a functi on that allows multiple IP interfaces to be assigned to the sam e VLAN. This is beneficial to the administrator when the num ber of IPs on the original interface is insuffic ...

  • D-Link TM DES-6500 - page 138

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create ipif to be created. The address and mask information can be specified using the traditional format (for ex ample, 10.1.2.3/255.0.0.0) or in CIDR format, (10.1.2.3/8). <vlan_name 32> − The name of the VLAN that will be associated with the above IP interface. secondary ...

  • D-Link TM DES-6500 - page 139

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ipif vlan <vlan_name 32> − The name of the VLAN corresponding to the previously created IP interf ace. If a primary and secondary IP interface are configured for the same VLAN (subnet), the user cannot change the VLAN of the IP interface. state [enabled | disabled] ? ...

  • D-Link TM DES-6500 - page 140

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual disable ipif Purpose Used to disable the configurat ion of an IP interface on the Switch. Syntax disable ipif {<ipif_name 12> | all} Description This command will disable an IP interface on the Switch, without altering its configuration values. Parameters <ipif_name 12> ...

  • D-Link TM DES-6500 - page 141

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show ipif Purpose Used to display the configurat ion of an IP interface on the Switch. show ipif {<ipif_name 12>} This command will display the configuration of an IP interface on the Switch. Parameters <ipif_name 12> − The name created for the IP interface to be viewe ...

  • D-Link TM DES-6500 - page 142

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 18 IGMP C OMM ANDS (I NCLUDING IGMP V 3) IGMP or Internet Group Management Protoc ol is a protocol implemented by system s utilizing IPv4 to collect the mem bership informati on needed by the multicast routing protocol through various query m essages sent out from the router or swi ...

  • D-Link TM DES-6500 - page 143

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config igmp last_member_query_interv al <value 1-25> | state [enabled | disabled]} Description This command allows IGMP to be configured on the Switch. <ipif_name 12> − The name of the IP interface for which to configure IGMP. all − Specifies all the IP interfaces on ...

  • D-Link TM DES-6500 - page 144

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To display IGMP confi gurations: DES-6500:4#show igmp Command: show igmp IGMP Interface Configurations Interface IP Address/Netmask Ver- Query Maximum Robust- Last State sion Response ness Member Time Value Query Interval ------------ --------------- ---- ------ -------- ------- --- ...

  • D-Link TM DES-6500 - page 145

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show igmp group ipif System group 224.0.1.1 Command: show igmp group ipif System group 224.0.1.1 Interface Name Multicast Group Last Reporter IP Querier IP Expire -------------------- ------------------- --------------------- ------------------ -------------- System 224.0 ...

  • D-Link TM DES-6500 - page 146

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 19 IGMP S NOOPING C OMM ANDS The IGMP Snooping comma nds in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config igmp_snooping [<vlan_name 32> | a ll] {host_timeout <sec 1-16711450> | router ...

  • D-Link TM DES-6500 - page 147

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config igmp_snooping default is 260 seconds. leave_timer <sec 1-16711450> − Leave timer. The default is 2 seconds. state [enabled | disabled] − Allows the user to enable or disable IGMP snooping for the specified VLAN. Restrictions Only administrator-lev el users can issue ...

  • D-Link TM DES-6500 - page 148

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config igmp_snooping querier interval) + (1 x query response interval). • Other querier present interval—A mount of time that must pass before a multicast router decides that there is no longer another multicast router that is the querier. This interval is calculated as follows: ...

  • D-Link TM DES-6500 - page 149

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To enable IGMP snooping on the Swi tch: DES-6500:4#enable igmp_snooping Command: enable igmp_snooping Success. DES-6500:4# disable igmp_snooping Purpose Used to enable IGMP snooping on the Switch. Syntax disable igmp_snooping {forw ard_mcrouter_only} Description This command disable ...

  • D-Link TM DES-6500 - page 150

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config router_ports number and the beginning port number on that slot, separated by a colon. Then the highest slot number, and the highest port number of the range (also separated by a colon) are specified. The beginning and end of the port list range are separated by a dash. For ex ...

  • D-Link TM DES-6500 - page 151

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config router_ports_forbidden default add 2:1-2:10 Command: config router_ports_forbidden default add 2:1-2:10 Success. DES-6500:4# show router_ports Purpose Used to display the current ly configured router ports on the Switch. Syntax show router_ports {vlan <vlan_name ...

  • D-Link TM DES-6500 - page 152

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show igmp_snooping Parameters <vlan_name 32> − The name of the VLAN for which to view the IGMP snooping configuration. Restrictions None. Example usage: To show igmp snooping: DES-6500:4#show igmp_snooping Command: show igmp_snooping IGMP Snooping Global State : Disabled Mul ...

  • D-Link TM DES-6500 - page 153

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: VLAN Name : default MAC address : 01-00-5E-00-00-02 Reports : 2 To show igmp snooping group: DES-6500:4#show igmp_snooping group Command: show igmp_snooping group Multicast group: 224.0.0.2 Reports : 1 Port Member : 1:16,2:7 VLAN Name : default Multicast group: 224.0. ...

  • D-Link TM DES-6500 - page 154

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To view the IGMP snooping forwarding t able for VLAN “Trinity”: DES-6500:4#show igmp_snooping forw arding vlan Trinity Command: show igmp_snooping forw arding vlan Trinity VLAN Name : Trinity Port Member : 1:17 Multicast group : 224.0.0.2 MAC address : 01-00-5E-00 ...

  • D-Link TM DES-6500 - page 155

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 21 A CCESS A UTHENTICA TION C ONTROL C OM MANDS The Access Authentication Control comma nds allows secure access to the Switch us ing the TACACS / XTACACS / TACACS+ and RADIUS protocols. When a user logs in to the Switch or tries to access the administrator level privilege, he or sh ...

  • D-Link TM DES-6500 - page 156

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual NOTE: TACACS, XTACACS and TACACS+ are separate entities and are not compatible. The Switch and the se rver must be configured exactly the same, using the same protocol. (For ex ample, if the Switch is set up for TACACS authentication, so must be the host server.) The Access Authenti ...

  • D-Link TM DES-6500 - page 157

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command Parameters show authen server_host config authen parameter response_timeout <int 1-255> <int 1-255> show authen parameter enable admin config admin local_enable <password 15> config authen parameter attempt Each command is listed, in detail, in the followin ...

  • D-Link TM DES-6500 - page 158

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To disable the system access authentication policy: DES-6500:4#disable authen_policy Command: disable authen_policy Success. DES-6500:4# show authen_policy Purpose Used to display the system access authentication policy status on the Switch. Syntax show authen_policy ...

  • D-Link TM DES-6500 - page 159

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#create authen_login method_list_name Trinity Command: create authen_login method_list_name Trinity Success. DES-6500:4# config authen_login Purpose Used to configure a user-defined or default method list of authentication methods for user login. Syntax config authen_login ...

  • D-Link TM DES-6500 - page 160

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config authen_login authenticated using the local user account database on the Switch.  none – Adding this parameter will require no authentication to access the Switch. method_list_name – Enter a previously implemented method list name defined by the user. The user may add o ...

  • D-Link TM DES-6500 - page 161

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config authen_login default method xtacacs tacacs+ local Command: config authen_login default method xtacacs tacacs+ local Success. DES-6500:4# delete authen_login method_list_name Purpose Used to delete a previously configured user defined method list of authentication m ...

  • D-Link TM DES-6500 - page 162

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show authen_login security protocols which are permanently set in the Switch. Keyword refers to authentication using a technique instead of TACACS/XTACACS/TACAC S+ and RADIUS, which are local (authentication through the user account on the Switch) and none (no authentication necessa ...

  • D-Link TM DES-6500 - page 163

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#create authen_enable method_list_name Permit Command: show authen_login method_list_name Permit Success. DES-6500:4# config authen_enable Purpose Used to configure a user- defined method list of authentication methods for promoting normal user level privileges to Administ ...

  • D-Link TM DES-6500 - page 164

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config authen_enable require the user to be authenticated using a user-defined server group previously configured on the Switch.  local_enable – Adding this parameter will require the user to be authenticated using the local user account database on the Switch.  none – Add ...

  • D-Link TM DES-6500 - page 165

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config authen_enable default method xtacacs tacacs+ local Command: config authen_enable default method xtacacs tacacs+ local Success. DES-6500:4# delete authen_enable method_list_name Purpose Used to delete a user-defined method list of authentication methods for promotin ...

  • D-Link TM DES-6500 - page 166

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show authen_enable refers to server groups defined by the user. Built-in Group refers to the TACACS/XTA CACS/TACACS+ and RADIUS security protocols which are permanently set in the Switch. Keyword refers to authentication using a technique INSTEAD of TACACS/XTACACS/TACAC S+ and RADIU ...

  • D-Link TM DES-6500 - page 167

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config authen application  telnet – Choose this parameter to configure the telnet login method.  ssh - Choose this parameter to configure the SSH (Secure Shell) login method.  http – Choose this parameter to configure the web interface login method.  all – Choose t ...

  • D-Link TM DES-6500 - page 168

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show authen application Command: show authen application Application Login Method List Enable Method List ---------------- ------------------ ------------------------ Console default default Telnet Trinity default SSH default default HTTP default default DES-6500:4# creat ...

  • D-Link TM DES-6500 - page 169

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create authen server_host   <key_string 254> - Specify an alphanumeric string up to 254 characters to be a key for the TACACS server. none – Specify this parameter to not use any key. timeout <int 1-255> - Enter the time in seconds the Switch will wait for the se ...

  • D-Link TM DES-6500 - page 170

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config authen server_host TACACS protocol.  xtacacs - Enter this parameter if the server host utilizes the XTACACS protocol.  tacacs+ - Enter this parameter if the server host utilizes the TACACS+ protocol.  radius - Enter this parameter if the server host utilizes the RADI ...

  • D-Link TM DES-6500 - page 171

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual delete authen server_host  tacacs – Enter this parameter if the server host utilizes the TACACS protocol.  xtacacs - Enter this parameter if the server host utilizes the XTACACS protocol.  tacacs+ - Enter this parameter if the server host utilizes the TACACS+ protocol. ? ...

  • D-Link TM DES-6500 - page 172

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show authen server_host Command: show authen server_host IP Address Protocol Port Timeout Retransmit Key --------------- -------- ----- ------- --------------- -------- 10.53.13.94 TACACS 49 5 2 -------- Total Entries : 1 DES-6500:4# create authen server_group Purpose Use ...

  • D-Link TM DES-6500 - page 173

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config authen server_group built into the Switch (TACACS/XT ACACS/TACACS+/RADIUS), or by a user-defined group previously created using the create authen server_group command. [add | delete] – Enter the correct parameter to add or delete a server host from a server group. server_ho ...

  • D-Link TM DES-6500 - page 174

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual delete authen server_group Purpose Used to delete a user-def ined authentication server group. Syntax delete authen server_group <string 15> Description This command will delete an authentication server group. Parameters <string 15> - Enter an alphanumeric string of up t ...

  • D-Link TM DES-6500 - page 175

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show authen server_group Command: show authen server_group Group Name IP Address Protocol --------------- --------------- -------- radius ---------------------------------------- Darren 10.53.13.2 TACACS tacacs 10.53.13.94 TACACS tacacs+ ---------------------------------- ...

  • D-Link TM DES-6500 - page 176

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config authen parameter attempt Purpose Used to configure the maximu m number of times the Switch will accept authentication attempts. Syntax config authen parameter attempt <int 1-255> Description This command will configure the maximum number of times the Switch will accept ...

  • D-Link TM DES-6500 - page 177

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show authen parameter Command: show authen parameter Response timeout: 60 seconds User attempts : 5 DES-6500:4# enable admin Purpose Used to promote user level privileges to administrator level privileges. Syntax enable admin Description This command is for users who have ...

  • D-Link TM DES-6500 - page 178

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config admin local_enable Parameters <password 15> - After entering this command, the user will be prompted to enter the old password, then a new password in an alphanumeric string of no more than 15 characters, and finally prompted to enter the new password again to confirm. ...

  • D-Link TM DES-6500 - page 179

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 22 SSH C OMM ANDS The steps required to use the SSH protocol for secure com munica tion bet ween a remote PC (the SSH Cl ient) and the Switch (the SSH Server), are as follows:      Create a user account with adm in-level access using the create account admin <usern ...

  • D-Link TM DES-6500 - page 180

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual enable ssh Purpose Used to enable SSH. Syntax enable ssh Description This command is used to enable SSH on the Switch. Parameters None. Restrictions Only administrator-lev el users can issue this command. Usage Example: To enable SSH: DES-6500:4#enable ssh Command: enable ssh Succes ...

  • D-Link TM DES-6500 - page 181

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ssh authmode Parameters password – This parameter may be c hosen if the administrator wishes to use a locally configured password for authentication on the Switch. publickey - This parameter may be chosen if the administrator wishes to use a publickey configuration set on a ...

  • D-Link TM DES-6500 - page 182

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ssh server Purpose Used to configure the SSH server. Syntax config ssh server {maxsession <int 1-8> | contimeout <sec 120- 600> | authfail <int 2-20> | rekey [10min | 30min | 60min | nev er] | port <tcp_port_number 1-65535>} Description This command al ...

  • D-Link TM DES-6500 - page 183

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4# show ssh server Command: show ssh server SSH Max Session : 3 SSH Server Status : Disabled Connection timeout : 120 (sec) Authenticate failed attempts : 2 Rekey timeout : Nev er Listened Port Number : 22 DES-6500:4# config ssh user Purpose Used to configure the SSH user. ...

  • D-Link TM DES-6500 - page 184

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4# config ssh user Trinity authmode Password Command: config ssh user Trinity authmode Password Success. DES-6500:4# show ssh user authmode Purpose Used to display the SSH user setting. Syntax show ssh user authmode Description This command allows you to display the current ...

  • D-Link TM DES-6500 - page 185

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ssh algorithm AES256 - This parameter will enable or disable the Advanced Encryption Standard AES256 encryption algorithm. arcfour - This parameter will enable or disable the Arcfour encryption algorithm. blowfish - This parameter will enable or disable the Blowfish encryptio ...

  • D-Link TM DES-6500 - page 186

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Usage Example: To display SSH algorithms currently set on the Switch: DES-6500:4#show ssh algorithm Command: show ssh algorithm Encryption Algorithm 3DES :Enable AES128 :Enable AES192 :Enable AES256 :Enable ARC4 :Enable Blow fish :Enable Cast128 :Enable Tw ofish128 :Enable Tw ofish1 ...

  • D-Link TM DES-6500 - page 187

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 23 SSL C OMMANDS Secure Sockets Layer or SSL is a security feature that will prov ide a secure communication path between a host an d client through the use of authentication, digi tal signatures and encrypti on. These security functions are im plemented through t he use of a cipher ...

  • D-Link TM DES-6500 - page 188

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Each command is listed, in detail, in the followin g sections. enable ssl Purpose To enable the SSL function on the Switch. Syntax enable ssl {ciphersuite {RSA_w ith_RC4_128_MD5 | RSA_w ith_3DES_EDE_CBC_SHA | DHE_DSS_w ith_3DES_EDE_CBC_SHA | RSA_EXPORT_w ith_RC4_40_MD5}} Description ...

  • D-Link TM DES-6500 - page 189

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual NOTE: Enabling the SSL function on the Switch will disable the port for the web manager (port 80). To log on to the web based manager, the entry of your URL must begin with https:// . (ex. https://10.90.90.90) disable ssl Purpose To disable the SSL function on the Switch. Syntax dis ...

  • D-Link TM DES-6500 - page 190

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ssl cachetimeout Purpose Used to configure the SSL cache timeout. Syntax config ssl cachetimeout timeout <value 60-86400> Description This command will set the time between a new key exchange between a client and a host using the SSL function. A new SSL session is estab ...

  • D-Link TM DES-6500 - page 191

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show ssl Purpose Used to view the SSL status and the certificate file status on the Switch. Syntax show ssl {certificate} Description This command is used to view the SSL status on the Switch. Adding the certificate parameter will allow the user to view the certificate file informat ...

  • D-Link TM DES-6500 - page 192

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual download certificate Parameters <ipaddr> - Enter the IP address of the TFTP server. certfilename <path_filename 64> - Enter the path and the filename of the certificate file to download. keyfilename <path_filename 64> - Enter the path and the filename of the key ex ...

  • D-Link TM DES-6500 - page 193

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 24 802.1X C OMM ANDS The xStack DES-6500 implement the server-s ide of the IEEE 802.1x Port-based and MA C-based Network Access Control. This mechanism is intended to allow only author ized users, or other network devices, acce ss to network resources by establishing criteria for ea ...

  • D-Link TM DES-6500 - page 194

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command Parameters statistics show auth_statistics {por ts [<portlist> | all]} Each command is listed, in detail, in the followin g sections. enable 802.1x Purpose Used to enable the 802.1x server on the Switch. Syntax enable 802.1x Description The enable 802.1x command enable ...

  • D-Link TM DES-6500 - page 195

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create 802.1x user Purpose Used to create a new 802.1x user. create 802.1x user <username 15> The create 802.1x user command is used to create new 802.1x users. <username 15> − A username of up to 15 alphanumeric characters in length. Only administrator-lev el users ca ...

  • D-Link TM DES-6500 - page 196

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual delete 802.1x user Used to delete an 802.1x user account on the Switch. delete 802.1x user <username 15> The delete 802.1x user command is used to delete the 802.1x Port- based or MAC-based Network Access control local users currently configured on the Switch. <username 15& ...

  • D-Link TM DES-6500 - page 197

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show 802.1x auth_configuration forces the Authenticator of t he port to become Authorized. ForceUnauth forces the por t to become Unauthorized. QuietPeriod − Shows the time interval between authentication failure and the start of a new authentication attempt. TxPeriod − Shows th ...

  • D-Link TM DES-6500 - page 198

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show 802.1x auth_state Purpose Used to display the current authentication stat e of the 802.1x server on the Switch. Syntax show 802.1x auth_state {ports [<portlist> | all]} Description The show 802.1x auth_state command is used to display the current authentication state of t ...

  • D-Link TM DES-6500 - page 199

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 1:11 ForceAuth Success Authorized 1:12 ForceAuth Success Authorized 1:13 ForceAuth Success Authorized 1:14 ForceAuth Success Authorized 1:15 ForceAuth Success Authorized 1:16 ForceAuth Success Authorized 1:17 ForceAuth Success Authorized 1:18 ForceAuth Success Authorized 1:19 ForceA ...

  • D-Link TM DES-6500 - page 200

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To configure 802.1x authentication by MAC address: DES-6500:4#config 802.1x auth_mode mac_based Command: config 802.1x auth_mode mac_based Success. DES-6500:4# config 802.1x capability ports Purpose Used to configure the 802.1x capability of a range of ports on the Switch. Syntax co ...

  • D-Link TM DES-6500 - page 201

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config 802.1x auth_parameter Purpose Used to configure the 802. 1x Authentication parameters on a range of ports. The default parameter will return all ports in the specified range to their default 802.1x settings. Syntax config 802.1x auth_parameter ports [<por tlist> | all] ...

  • D-Link TM DES-6500 - page 202

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config 802.1x auth_parameter sending packets to a supplicant (user). reauth_period <sec 1-65535> − Configures the time interval between successive re-authentications. enable_reauth [enable | disable] − Determines whether or not the Switch will re-authenticate. Enabl ed cau ...

  • D-Link TM DES-6500 - page 203

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config 802.1x init Purpose Used to initialize the 802. 1x function on a range of ports. Syntax config 802.1x init [port_based ports [<portlist>| all] | mac_based [ports] [<portlist> | all] {mac_address <macaddr>] Description The config 802.1x init command is used t ...

  • D-Link TM DES-6500 - page 204

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config 802.1x reauth ports Purpose Used to configure the 802.1x re-authentication feature of the Switch. Syntax config 802.1x reauth [port_based ports [<portlist>| all] | mac_based [ports] [<portlist> | all] {mac_address <macaddr>] Description The config 802.1x rea ...

  • D-Link TM DES-6500 - page 205

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config radius add Purpose Used to add a new RADIUS server. Syntax config radius add <server_index 1-3> <server_ip> key <passw d 32> [default | {auth_port <udp_port_number 1- 65535> | acct_port <udp_port_number 1-65535>}] Description The config radius ad ...

  • D-Link TM DES-6500 - page 206

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config radius delete 1 Command: config radius delete 1 Success. DES-6500:4# config radius Purpose Used to configure t he Switch’s RADIUS settings. Syntax config radius <server_index 1-3> {ipaddress <server_ip> | key <passw d 32> | auth_port <udp_por ...

  • D-Link TM DES-6500 - page 207

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To display RADIUS settings on th e Switch: DES-6500:4#show radius Command: show radius Idx IP Address Auth-Port Acct-Port Status Key Number Number ----- ------------------ --------- --------- ----------- ------------ 1 10.1.1.1 1812 1813 Active switch 2 20.1.1.1 1800 ...

  • D-Link TM DES-6500 - page 208

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show auth_client Purpose Used to display the curr ent RADIUS authentication client. show auth_client The show auth_client command is used to display the current RADIUS authentication client curr ently configured on the Switch. Parameters None. Restrictions None. Syntax Description E ...

  • D-Link TM DES-6500 - page 209

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show auth_diagnostics all – Specifies that all ports will be viewed. Restrictions None. Example usage: To display the current aut hentication diagnostics for port 16: DES-6500:4#show auth_diagnostics ports 1:16 Command: show auth_diagnostics ports 1:16 Port number : 1:16 EntersCon ...

  • D-Link TM DES-6500 - page 210

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To display the current auth entication session statistics for p ort 16: DES-6500:4#show auth_session_statistics ports 1:16 Command: show auth_session_statistics ports 1:16 Port number : 1:16 SessionOctetsRx 0 SessionOctetsTx 0 SessionFramesRx 0 SessionFramesTx 0 SessionId SessionAut ...

  • D-Link TM DES-6500 - page 211

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show auth_statistics ports 1:16 Command: show auth_statistics ports 1:16 Port number : 1:16 EapolFramesRx 0 EapolFramesTx 0 EapolStartFramesRx 0 EapolReqIdFramesTx 0 EapolLogoffFramesRx 0 EapolReqFramesTx 0 EapolRespIdFramesRx 0 EapolRespFramesRx 0 InvalidEapolFramesRx 0 ...

  • D-Link TM DES-6500 - page 212

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 25 A CCESS C ONTROL L IST (ACL) C OMMANDS (I NCLUDING CPU) The xStack DES-6500 implement Access Contro l Lists that enable the Switch to deny network access to specific devices or device groups based on IP settings, MAC addre ss, packet content and IPv6 settings. Command Parameters ...

  • D-Link TM DES-6500 - page 213

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command Parameters delete cpu access_profile profile_id <value 1-5> config cpu access_profile profile_id <value 1-5> [add access_id <v alue 1-100> [ethernet {vlan <vlan_name 32> | source_mac <macaddr> | destinati on_mac <macaddr> | ethernet_type & ...

  • D-Link TM DES-6500 - page 214

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual The ip parameter instructs the Switch that this new rule will be applied to the IP addresses contained within each fram e’s header. source_ip tells the Switch that this rule w ill apply to the source IP addresses in each frame’s header. Finally, the IP address 10.42.73.1 will be ...

  • D-Link TM DES-6500 - page 215

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command Parameters create access_profile profile_id <value 1-8> [ethernet {vlan | source_mac <macmask> | destination_mac <macmask> | 802.1p | ethernet_type} config access_profile profile_id <value 1-8> [add access_id <v alue 1-65535> [ethernet {vlan < ...

  • D-Link TM DES-6500 - page 216

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create access_profile (for Ethernet) Used to create an access profile on the Switch by examining the Ethernet part of the packet header. Masks entered can be combined with the values the Switch finds in the specified frame header fields. Specific values for the rules are entered usi ...

  • D-Link TM DES-6500 - page 217

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config access_profile profile_id (for Ethernet) Purpose Used to configure the Ethernet access profile on the Switch and to define specific values for the rules that will be used to by the Switch to determine if a given packet should be forwarded or filtered. Masks entered using the ...

  • D-Link TM DES-6500 - page 218

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config access_profile profile_id (for Ethernet) permitted to be forwarded by the Switch. replace_dscp <value 0-63> − Allows specification of a value to be written to the DSCP field of an incoming packet that meets the criteria specified in the first par t of the command. Thi ...

  • D-Link TM DES-6500 - page 219

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create access_profile (IP) 0x0-0xffff> | dst_port_mask <hex 0x0-xffff>} | protocol_id {user _mask <hex 0x0-0xffffffff>}]} Description This command will allow the user to create a profile for packets that may be accepted or denied by the Swit ch by examining the IP par ...

  • D-Link TM DES-6500 - page 220

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create access_profile (IP) mask for the destination port. • protocol_id − Specifies that the Switch will examine each frame’s Protocol ID field. • user_define <hex 0x0-0xfffffff> − Enter a hexidecimal value that will identify the protocol to be discovered in the pack ...

  • D-Link TM DES-6500 - page 221

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config access_profile profile_id (IP) packet to see if it will be either forwarded or filtered based on one or more of the following: • vlan <vlan_name 32> − Specifies that the access profile will apply to only to this VLAN. • source_ip <ipaddr> − Specifies that ...

  • D-Link TM DES-6500 - page 222

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config access_profile profile_id (IP) their header. • protocol_id <value 0-255> − Specifies that the Switch will examine the Protocol field in each packet and if this field contains the value entered here, apply the appropriate rules. • user_define <hex 0x0-0xfffffff& ...

  • D-Link TM DES-6500 - page 223

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create access_profile (packet content mask) Purpose Used to create an access profile on the Switch by examining the Ethernet part of the packet header. Packet content masks entered will specify certain bytes of the packet header to be identified by the Switch. When the Switch recogn ...

  • D-Link TM DES-6500 - page 224

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config access_profile profile_id (packet content mask) Purpose To configure the rule for a previously created access profile command based on the packet content mask. Packet content masks entered will specify certain bytes of the packet header to be identified by the Switch. When th ...

  • D-Link TM DES-6500 - page 225

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config access_profile profile_id (packet content mask) specifies switch number 2, port 4. 1:3-2:4 specifies all of the ports between switch 1, port 3 and switch 2, port 4 − in numerical order. permit – Specifies that packets that match the access profile are permitted to be forw ...

  • D-Link TM DES-6500 - page 226

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create access_profile (ipv6) Purpose Used to create an access profile on the Switch by examining the IPv6 part of the packet header. Masks can be entered that will be combined with the values the Switch finds in the specified frame header fields. Specific values fo r the rules are e ...

  • D-Link TM DES-6500 - page 227

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config access_profile profile_id (ipv6) Purpose Used to configure the IPv6 access profile on the Switch and to define specific values for the rules that will be used to by the Switch to determine if a given packet should be forwarded or filtered. Masks entered using the create acces ...

  • D-Link TM DES-6500 - page 228

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config access_profile profile_id (ipv6) used to determine the CoS queue to which packets are forwarded to. Once this field is specified, packets accepted by the Switch that match this pr iority are forwarded to the CoS queue specified previously by the user. • {replace_priority} ? ...

  • D-Link TM DES-6500 - page 229

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4# delete access_profile profile_id 1 Success. Command: delete access_profile profile_id 1 DES-6500:4# show access_profile Purpose Used to display the current ly configured access profiles on the Switch. Syntax show access_profile {profile_id <value 1-8>} Description ...

  • D-Link TM DES-6500 - page 230

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 2 ====================================================================== Access Profile ID: 3 TYPE : Packet Content ====================================================================== MASK Option : Offset 0-15 : 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF Offset 16-31 : 0x0000FFF ...

  • D-Link TM DES-6500 - page 231

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create cpu access_profile address mask. • destination_mac <macmask> - Specifies to examine the destination MAC address mask. • ethernet_type − Specifies that the switch will examine the Ethernet type value in each frame’s header. ip − Specifies that the switch will e ...

  • D-Link TM DES-6500 - page 232

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create cpu access_profile • dst_port_mask <hex 0x0-0xffff> − Specifies a UDP port mask for the destination port. • protocol_id − Specifies that the Switch will examine each frame’s Protocol ID field. • user_define_mask < hex 0x0-0xffffffff> − Specifies that ...

  • D-Link TM DES-6500 - page 233

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To delete the cpu access profile with a profile ID of 1: DES-6500:4#delete cpu access_profile profile_id 1 Command: delete cpu access_profile profile_id 1 Success. DES-6500:4# config cpu access_profile Purpose Used to configure a cpu access pr ofile used for CPU Interface Filtering ...

  • D-Link TM DES-6500 - page 234

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config cpu access_profile • vlan <vlan_name 32> − Specifies that the access profile will apply to only to this VLAN. • vlan <vlan_name 32> − Specifies that the access profile will apply to only this VLAN. • source_mac <macaddr> − Specifies that the acce ...

  • D-Link TM DES-6500 - page 235

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config cpu access_profile in their header. • protocol_id <value 0-255> − Specifies that the Switch will examine the protocol field in each packet and if th is field contains the value entered here, apply the following rules. • packet_content_mask – Specifies that the S ...

  • D-Link TM DES-6500 - page 236

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual enable cpu_interface_filtering Purpose Used to enable CPU interface filtering on the Switch. Syntax enable cpu_interface_filtering Description This command is used, in conjunction with the disable cpu_interface_filtering command below, to enable and disable CPU interface filtering o ...

  • D-Link TM DES-6500 - page 237

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show cpu_interface_filtering Parameters None. Restrictions Only administrator-lev el users can issue this command. Example usage: To show the CPU filtering state o n the Switch: DES-6500:4#show cpu_interface_filtering Command: show cpu_interface_filtering Cpu_interface_filtering Sta ...

  • D-Link TM DES-6500 - page 238

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 26 S AFEGUARD E NGINE C OMM ANDS Periodically, malicious hosts on the network will attack the Switc h by utilizing packet flooding (A RP Storm ) or other methods. These attacks may increase the CPU utilization beyond its capability. To alleviate this problem , the Safeguard Engine f ...

  • D-Link TM DES-6500 - page 239

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config safeguard_engine Purpose Used to configure the Saf eguard Engine settings for the Switch. Syntax config safeguard_engine {state [enable | disable] | utilization {rising <value 20-100> | falling <value 20-100> | trap_log [enable | disable} | mode [strict | fuzzy]} ...

  • D-Link TM DES-6500 - page 240

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show safeguard_engine Purpose To display the Safeguard E ngine parameters currently set in the Switch. Syntax show safeguard_engine Description This command is used to s how the Safeguard Engine information currently set on the Switch. Parameters None. Restrictions None. Example usa ...

  • D-Link TM DES-6500 - page 241

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 26 T RAFFIC S EGMENT A TION C OM MANDS Traffic segmentation allows you to further sub-divide VLANs into sm aller groups of ports that will help to reduce traffic on th e VLAN. The VLAN rules take precedence, a nd then the traffic segmentation rules are applied. The traffic segmentat ...

  • D-Link TM DES-6500 - page 242

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show traffic_segmentation Purpose Used to display the current tr affic segmentation configuration on the Switch. Syntax show traffic_segmentation <portlist> Description The show traffic_segmentation command is used to display the current traffic segmentation configuration on t ...

  • D-Link TM DES-6500 - page 243

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 28 D-L INK S INGLE IP M ANAGEMENT C OM MANDS Simply put, D-Link Single IP Management is a con cept that will stack switches tog ether over Eth ernet instead o f using stacking ports or m odules. Switches using Single IP Managem ent (labeled here as SIM) m ust conform to the foll owi ...

  • D-Link TM DES-6500 - page 244

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 2. CS’s m ust change their role to CaS and then to M S, to become a MS of a SIM group. Thus the CS cannot directly be converted to a MS. 3. The user can manually configure a CS to become a CaS. 4. A MS can become a CaS by: a. Being configured as a CaS through the CS. b. If report ...

  • D-Link TM DES-6500 - page 245

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual enable sim Purpose Used to enable Single IP Management (SIM) on the Switch Syntax enable sim Description This command will enable SIM gl obally on the Switch. SIM features and functions will not function pr operly unless this function is enabled. Parameters None. Restrictions Only a ...

  • D-Link TM DES-6500 - page 246

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show sim Description This command will display the current information regarding the SIM group on the Switch, including the following: SIM Version - Displays the current Single IP Management version on the Switch. Firmware Version - Displays the current Firmware version on the Switc ...

  • D-Link TM DES-6500 - page 247

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show sim Command: show sim SIM Version : VER-1 Firmw are Version : Build 3.00-B29 Device Name : MAC Address : 00-35-26-11-11-00 Capabilities : L3 Platform : DES-6500 L3 Sw itch SIM State : Enabled Role State : Commander Discovery Interval : 30 sec Hold Time : 100 sec DES- ...

  • D-Link TM DES-6500 - page 248

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To show other groups informati on in summa ry, if group is specified: DES-6500:4#show sim group Command: show sim group SIM Group Name : default ID MAC Address Platform / Hold Firmw are Device Name Capability Time Version --- ----------------- ------------------------ ----- -------- ...

  • D-Link TM DES-6500 - page 249

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual reconfig Purpose Used to connect to a member switch, through the commander switch using telnet. Syntax reconfig [member_id <value 1-32> | exit] Description This command is used to reconnec t to a member switch using telnet. Parameters member_id <value 1-32> - Select the ...

  • D-Link TM DES-6500 - page 250

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config sim_group delete 1 Command: config sim_group delete 1 Please w ait for ACK... Success. DES-6500:4# config sim Purpose Used to configure role param eters for the SIM protocol on the Switch. Syntax config sim [{[commander {group_name <groupname 64> | candidate] ...

  • D-Link TM DES-6500 - page 251

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config sim commander dp_interval 30 Command: config sim commander dp_interval 30 Success. DES-6500:4# To change the hold tim e of the discovery protocol: DES-6500:4# config sim commander hold_time 120 Command: config sim commander hold_time 120 Success. DES-6500:4# To tra ...

  • D-Link TM DES-6500 - page 252

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual download sim_ms Purpose Used to download firmware or configuration file to an indicated device. Syntax dow nload sim_ms [firmw are | configuration] <ipaddr> <path_filename> {[members <mslist 1-32> | all]} Description This command will download a firmwa re file or c ...

  • D-Link TM DES-6500 - page 253

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#dow nload sim_ms configurati on 10.53.13.94 c:/dgssri.txt members all Command: dow nload sim_ms configuration 10.53.13.94 c:/dgssri.txt members all This device is updating configuration. Please wait... Dow nload Status : ID MAC Address Result --- ----------------- ------- ...

  • D-Link TM DES-6500 - page 254

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 29 T IME AND SNTP C OMMANDS The Simple Net work Time Protocol (SNTP) {an adaptat ion of the Network Time Protocol (NTP)} comma nds in the Command Line Interface (CLI) are listed (along with the a ppropriate parameters) in the following table. Command Parameters config sntp {primary ...

  • D-Link TM DES-6500 - page 255

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To configure SNTP settings: DES-6500:4#config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 Command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 Success. DES-6500:4# show sntp Purpose show sntp This command will display SNTP settings information incl ...

  • D-Link TM DES-6500 - page 256

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#enable sntp Command: enable sntp Success. DES-6500:4# disable sntp Purpose Disables SNTP server support. Syntax disable sntp Description This will disable SNTP s upport. SNTP service must be separately configured (see config sntp). Parameters None. Restrictions Only admin ...

  • D-Link TM DES-6500 - page 257

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config time 30jun2003 16:30:30 Command: config time 30jun2003 16:30:30 Success. DES-6500:4# config time zone Purpose Used to determine the time zone used in order to adjust the system clock. Syntax config time_zone {operator [+ | -] | hour <gmt_hour 0-13> | min < ...

  • D-Link TM DES-6500 - page 258

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config dst requirement. DST adjustment effects system time for both manually configured time and time set using SNTP service. Parameters disable - Disable the DST seasonal time adjustment for the Switch. repeating - Using repeating mode will enable DST seasonal time adjustment. Repe ...

  • D-Link TM DES-6500 - page 259

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config dst e_date - Configure the specific date (day of the month) to begin DST. • <end_date 1-31> - The end date is expressed numerically. offset [30 | 60 | 90 | 120] - Indicates number of minutes to add or to subtract during the summertime. The possible offset times are 30 ...

  • D-Link TM DES-6500 - page 260

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 30 ARP C OMM ANDS The ARP commands in the Com mand Line Interface (CLI) are liste d (along with the appropriate param eters) in the following table. Command Parameters create arpentry <ipaddr> <macaddr> delete arpentry [<ipaddr> | all] {ipif <ipif_name 12> | ...

  • D-Link TM DES-6500 - page 261

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual delete arpentry table. Parameters <ipaddr> − The IP address of the end node or station. all − Deletes all ARP entries. Only administrator-lev el users can issue this command. Restrictions Example Usage: To delete an entry of IP address 10.48.74.121 from the ARP table: DES- ...

  • D-Link TM DES-6500 - page 262

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show arpentry Parameters ipif <ipif_name 12> − Enter the IP interface name for which to display ARP settings. static − Displays the static entries to the ARP table. Restrictions None. Example Usage: To display the ARP table : DES-6500:4#show arpentry Command: show arpentry ...

  • D-Link TM DES-6500 - page 263

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To display an entry in th e ARP table: DES-6500:4#show arpentry ipaddress 10.1.1.169 Command: show arpentry ipaddress 10.1.1.169 ARP Aging Time : 30 Interface IP Address MAC Address Type ------------- --------------- ----------------- --------------- System 10.1.1.169 00-50-BA-70-E4 ...

  • D-Link TM DES-6500 - page 264

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 31 VRRP C OMM ANDS VRRP or Virtual Routing Redundancy Prot ocol is a function on the Switch that dynami cally assigns responsibility for a virtual router to one of the VRRP routers on a LAN. The VRR P router that controls the IP address associated with a virtual router is called the ...

  • D-Link TM DES-6500 - page 265

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example Usage: To enable VRRP globally on the Switch: DES-6500:4#enable vrrp Command: enable vrrp Success. DES-6500:4# Example usage: To enable the virtual IP address to be pi nged: DES-6500:4#enable vrrp ping Command: enable vrrp ping Success. DES-6500:4# disable vrrp Purpose To di ...

  • D-Link TM DES-6500 - page 266

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create vrrp vrid Purpose To create a VRRP router on the Switch. Syntax vrid <vrid 1-255> ipif <ipif_name 12> ipaddress <ipaddr> {state [enable | disable] | priority <int 1-254> | adv ertisement_interval <int 1-255> | preempt [true | fa lse] | critical_i ...

  • D-Link TM DES-6500 - page 267

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create vrrp vrid network connections. critical_ip_state [enable | disable] - This parameter is used to enable or disable the critical IP addr ess entered above. The default is disable. Restrictions Only administrator-lev el users can issue this command. Example usage: To create a VR ...

  • D-Link TM DES-6500 - page 268

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config vrrp vrid gateway that will be statically assigned to end hosts and must be set for all routers that participate in this group. critical_ip <ipaddr> - Enter the IP address of the physical device that will provide the most direct route to the Internet or other critical n ...

  • D-Link TM DES-6500 - page 269

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config vrrp ipif Parameters authtype – Specifies the type of authentication used. The authtype must be consistent with all rout ers participating within the VRRP group. The user may choose between: ipif <ipif_name 12> - Enter the name of a previously configured IP interface ...

  • D-Link TM DES-6500 - page 270

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show vrrp Command: show vrrp Global VRRP :Enabled Non-ow ner response PING : Disabled Interface Name : System Authentication type : No Authentication VRID : 2 Virtual IP Address : 10.53.13.3 Virtual MAC Address : 00-00-5E-00-01-02 Virtual Rout er State : Master State : En ...

  • D-Link TM DES-6500 - page 271

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 32 R OUTING T ABLE C OMM ANDS The routing table comma nds in the Command Line Interface (CLI) are listed (along with the appropriate param eters) in the following table. Command Parameters create iproute <network_address> <i paddr> {<metric 1-65535>} {[primary | ba ...

  • D-Link TM DES-6500 - page 272

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create iproute default Purpose Used to create IP route entries to the Switch’s IP routing table. Syntax create iproute default <ipaddr> {<metric>} Description This command is used to create a default static IP route entry to the Switch’s IP routing table. Parameters ...

  • D-Link TM DES-6500 - page 273

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual delete iproute default Purpose Used to delete a default IP route entry from the Switch’s IP routing table. Syntax delete iproute default <ipaddr> Description This command will delete an existing default entry from the Switch’s IP routing table. Parameters <ipaddr> - ...

  • D-Link TM DES-6500 - page 274

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 33 R OUTE R EDISTRIBUTION C OMM ANDS The route redistribution comma nds in the Command Line Interface (CLI) are listed (al ong with the appropriate parameters) in the following table. Command Parameters create route redistribute dst ospf src [static | rip | local] {mettype [1 | 2] | ...

  • D-Link TM DES-6500 - page 275

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Route Source Metric Metric Type RIP 0 to 16777214 mettype 1 mettype 2 Static 0 to 16777214 mettype 1 mettype 2 Local 0 to 16777214 mettype 1 mettype 2 Allowed Metric Type combinations are mettype 1 or mettype 2 . The metric value 0 above will be redistributed in OSPF as the metric 2 ...

  • D-Link TM DES-6500 - page 276

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Routing inform ation source − OSPF and the Static Route table. Routing information will be redi stributed to RIP. The following table lists the allowed values for th e routing metrics and the types (or forms) of the rou ting information that will be redistr ibuted. Route Source Ty ...

  • D-Link TM DES-6500 - page 277

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config route redistribute dst ospf src • Type-1 calculates the metric (for RIP to OSPF) by adding the destination’s interface cost to the metric entered in the Metric field. • Type-2 uses the metric entered in the Metric field without change. This field applies only when the d ...

  • D-Link TM DES-6500 - page 278

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config route redistribute dst rip src Parameters src {all | internal | external | type_1 | type_2 | inter+e1 | inter+e2} − Allows the selection of the protocol of the source device. The user may choose between: metric <value 0-16> − Allows the entry of an OSPF interface co ...

  • D-Link TM DES-6500 - page 279

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example Usage: To delete route redist ribution settings: DES-6500:4#delete route redistribute dst rip src ospf Command: delete route redistribute dst rip src ospf Success. DES-6500:4# show route redistribute Purpose Used to display the route redistribution on the Switch. Syntax show ...

  • D-Link TM DES-6500 - page 280

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 34 DHCP R ELA Y C OM MANDS The DHCP relay commands in the Com mand Line Interface (CLI) are listed (along with the appropriate param eters) in the following table. Command Parameters config dhcp_relay {hops <val ue 1-16> | time <sec 0-65535>} config dhcp_relay add ipif & ...

  • D-Link TM DES-6500 - page 281

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config dhcp_relay add ipif Purpose Used to add an IP destination address to the Switch's DHCP/BOOTP relay table. Syntax config dhcp_relay add ipif <ipif_name 12> <ipaddr> Description This command adds an IP address as a destination to which to forward (relay) DHCP/B ...

  • D-Link TM DES-6500 - page 282

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config dhcp_relay option_82 state Purpose Used to configure the state of DHCP relay agent information option 82 of the switch. Syntax config dhcp_relay option_82 state [enable | disable] Description This command is used to c onfigure the state of DHCP relay agent information option ...

  • D-Link TM DES-6500 - page 283

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To configure DHCP relay opti on 82 check: DES-6500:4#config dhcp_relay option_82 check enable Command: config dhcp_relay option_82 check enable Success. DES-6500:4# config dhcp_relay option_82 policy Purpose Used to configure the forwarding policy of relay agent infor ...

  • D-Link TM DES-6500 - page 284

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To show the DHCP relay configurat ion: DES-6500:4#show dhcp_relay Command: show dhcp_relay DHCP/BOOTP Hops Count Limit : 2 System 10.58.44.6 DHCP/BOOTP Relay Status : Enabled DHCP/BOOTP Relay Time Threshold : 23 DHCP Relay Agent Information Option 82 State : Enabled DHCP Relay Agent ...

  • D-Link TM DES-6500 - page 285

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual disable dhcp_relay Used to disable the DHCP/BOOTP relay function on the switch. Syntax disable dhcp_relay Description This command is used to disable the DHCP/BOOTP relay function on the switch. Parameters None. Restrictions Only administrator-lev el users can issue this command. Pu ...

  • D-Link TM DES-6500 - page 286

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 35 DNS R ELA Y C OM MANDS The DNS relay commands in the Comm and Line Interface (CLI) ar e listed (along with the appropriate parame ters) in the following table. Command Parameters config dnsr [[primary | secondary] nameserver <ipaddr> | [add | delete] static <domain_name ...

  • D-Link TM DES-6500 - page 287

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config dnsr add static dns1 10.43.21.12 Command: config dnsr add static dns1 10.43.21.12 Success. DES-6500:4# Example Usage: To delete an entry dom ain name dns1, IP address 10.43.21.12 from DNS static table. DES-6500:4#config dnsr delete static dns1 10.43.21.12 Command: ...

  • D-Link TM DES-6500 - page 288

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#enable dnsr cache Command: enable dnsr cache Success. DES-6500:4# Example Usage: To enable static ta ble lookup for DNS relay. DES-6500:4#enable dnsr static Command: enable dnsr static Success. DES-6500:4# disable dnsr Purpose Used to disable DNS relay on the Switch. Synt ...

  • D-Link TM DES-6500 - page 289

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#disable dnsr cache Command: disable dnsr cache Success. DES-6500:4# Example Usage: To disable static t able lookup for DNS relay. DES-6500:4#disable dnsr static Command: disable dnsr static Success. DES-6500:4# show dnsr Purpose Used to display the current DNS relay statu ...

  • D-Link TM DES-6500 - page 290

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 36 RIP C OMM ANDS The RIP comma nds in the Command Line Inte rface (CLI) are listed (along with the a ppropriate parameters) in the following table. Command Parameters config rip [ipif <ipif_name 12> | a ll] {authentication [enabled <password 16> | disabled] | tx_mode [d ...

  • D-Link TM DES-6500 - page 291

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config rip reception of RIP packets. state [enabled | disabled] − Allows RIP to be enabled and disabled on the Switch. Restrictions Only administrator-lev el users can issue this command. • v1_only − Specifies that only RIP v1 packets will be transmitted. • v2_only - Specifi ...

  • D-Link TM DES-6500 - page 292

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To disable rip: DES-6500:4#disable rip Command: disable rip Success. DES-6500:4# show rip Purpose Used to display the RIP c onfiguration and statistics for the Switch. Syntax show rip {ipif <ipif_name 12>} Description This command will display the RIP configuration and statist ...

  • D-Link TM DES-6500 - page 293

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 37 DVMRP C OMM ANDS The DVMRP comma nds in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters config dvmrp [ipif <ipif_name 12> | a ll] {metric <value 1-31> | probe <sec 1- 65535> | neighbo ...

  • D-Link TM DES-6500 - page 294

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config dvmrp state [enabled | disabled] − Allows DVMRP to be enabled or disabled. Restrictions Only administrator-lev el users can issue this command. Example Usage: To configure DVMRP configura tions of IP interface System: DES-6500:4#config dvmrp ipif Sy stem ne ighbor_timeout 3 ...

  • D-Link TM DES-6500 - page 295

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example Usage: Command: disable dvmrp To disable DVMRP: DES-6500:4#disable dvmrp Success. DES-6500:4# show dvmrp routing_table Used to display the current DVMRP routing table. Syntax show dvmrp routing table [ipaddress <netw ork_address>] Description The command is used to dis ...

  • D-Link TM DES-6500 - page 296

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show dvmrp neighbor Parameters <ipif_name 12> − The name of the IP interface for which to display the DVMRP neighbor table. ipaddress <network_address> − The IP address and netmask of the destination. The address and mask information can be specified using the tradit ...

  • D-Link TM DES-6500 - page 297

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show dvmrp nexthop Command: show dvmrp nexthop Source IP Address/Netmask Interface Name Type ----------------- --------------- ------ 10.0.0.0/8 ip2 Leaf 10.0.0.0/8 ip3 Leaf 20.0.0.0/8 System Leaf 20.0.0.0/8 ip3 Leaf 30.0.0.0/8 System Leaf 30.0.0.0/8 ip2 Leaf Total Entrie ...

  • D-Link TM DES-6500 - page 298

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 38 PIM C OMM ANDS The PIM comma nds in the Command Line Inte rface (CLI) are listed (along with the a ppropriate parameters) in the following table. Command Parameters config pim [ipif <ipif_name 12> | all] {hello <sec 1-18724> | jp_interval <sec 1-18724> | state [ ...

  • D-Link TM DES-6500 - page 299

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config pim ipif System he llo 35 jp_interval 70 state enabled Command: config pim ipif System he llo 35 jp_interval 70 state enabled Success. DES-6500:4# enable pim Purpose Used to enable PIM function on the Switch. Syntax enable pim Description This command will enable P ...

  • D-Link TM DES-6500 - page 300

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show pim neighbor Purpose Used to display PIM neighbor router table entries. Syntax show pim neighbor {ipif <ipif_name 12> | ipaddress <netw ork_address>} Description This command will list current entries in the PIM neighbor table for a specified IP interface or destina ...

  • D-Link TM DES-6500 - page 301

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To display PIM sett ings as configured on the Switch: DES-6500:4#show pim Command: show pim PIM Global State : Disabled PIM-DM Interface Table Hello Join/Prune Interface IP Address Interval Interval State ------------ --------------- -------- ---------- -------- System 10.90.90.90/8 ...

  • D-Link TM DES-6500 - page 302

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 39 IP M UL TICASTING C OMM ANDS The IP multicasting comm ands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters show ipmc cache {group <group>} {ipaddress <network_address>} show ipmc {ipif & ...

  • D-Link TM DES-6500 - page 303

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show ipmc Purpose Used to display the IP multicast interface table. show ipmc {ipif <ipif_name 12> | protocol [inactive | dvmrp | pim} Description This command will display the cu rrent IP multicast interface table. Parameters <ipif_name 12> − The name of the IP interf ...

  • D-Link TM DES-6500 - page 304

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 40 MD5 C ONFIGURA TION C OMM ANDS The MD5 configuration comm ands in the Comm and Line Interface (C LI) are listed (along with the appropriate parameters) in the following table. Command Parameters create md5 key <key_id 1-255> <password 16> config md5 key <key_id 1-2 ...

  • D-Link TM DES-6500 - page 305

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#config md5 key 1 taboo Command: config md5 key 1 taboo Success. DES-6500:4# delete md5 key Purpose Used to delete an entry in the MD5 key table. Syntax delete md5 key <key_id 1-255> Description This command is used to delet e a specific entry in the MD5 key table. P ...

  • D-Link TM DES-6500 - page 306

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 41 OSPF C ONFIGURA TION C OMM ANDS The OSPF configuration comma nds in the Command Line Interface (C LI) are listed (along with the appropriate param eters) in the following table. Command Parameters config ospf router_id <ipaddr> enable ospf disable ospf show ospf create ospf ...

  • D-Link TM DES-6500 - page 307

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Command Parameters show ospf all create ospf virtual_link <area_id> <nei ghbor_id> {hello_interval <sec 1-65535> | dead_interval <sec 1-65535> | authentication [none | simple <password 8> | md5 <key_id 1-255>]} config ospf virtual_link <area_id ...

  • D-Link TM DES-6500 - page 308

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#enable ospf Command: enable ospf Success. DES-6500:4# disable ospf Purpose Used to disable OSPF on the Switch. Syntax disable ospf Description This command, in combination with the enable ospf command above, is used to enable and disable OSPF on the Switch. Parameters Non ...

  • D-Link TM DES-6500 - page 309

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To show OSPF state: DES-6500:4#show ospf Command: show ospf --------------- ------ ----------------------- ----------------- 10.1.1.1 Normal None None Total Entries : 4 ----------- --------------- -------- -------- -------------- ------ Area ID Aggregated LSDB Advertise OSPF Router ...

  • D-Link TM DES-6500 - page 310

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create ospf area Purpose Used to configure OSPF area settings. Syntax create ospf area <area_id> type [normal | stub {stub_summary [enabled | disabled] | metric <v alue 0- 65535>}] Description This command is used to create an OSPF area and configure its settings. Parame ...

  • D-Link TM DES-6500 - page 311

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ospf area Purpose Used to configure an OSPF area’s settings. Syntax config ospf area <area_id> type [normal | stub {stub_summary [enabled | disabled] | metric <v alue 0- 65535>}] Description This command is used to configure an OSPF area’s settings. Parameters ...

  • D-Link TM DES-6500 - page 312

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create ospf host_route Purpose Used to configure OSPF host route settings. Syntax create ospf host_route <ipaddr> {area <area_id> | metric <value 1-65535>} Description This command is used to c onfigure the OSPF host route settings. Parameters <ipaddr> − Th ...

  • D-Link TM DES-6500 - page 313

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ospf host_route Used to configure OSPF host route settings. Syntax config ospf host_route <ipaddr> {area <area_id> | metric <value>} Description This command is used to c onfigure an OSPF host route settings. Parameters <ipaddr> − The IP address of t ...

  • D-Link TM DES-6500 - page 314

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create ospf aggregation Purpose Used to configure OSPF area aggregation settings. Syntax create ospf aggregation <area_id> <netw ork_address> lsdb_type summary {advertise [enabled | disabled]} Description This command is used to create an OSPF area aggregation. Parameter ...

  • D-Link TM DES-6500 - page 315

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#delete ospf aggregation 10. 1.1.1 10.48.76.122/16 lsdb_type summary Command: delete ospf aggregation 10.1.1.1 10.48.76..122/16 lsdb_type summary Success. DES-6500:4# config ospf aggregation Purpose Used to configure t he OSPF area aggregation settings. Syntax config ospf ...

  • D-Link TM DES-6500 - page 316

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Usage Example Command: show ospf aggregation DES-6500:4# To display OSPF area aggregation settings: DES-6500:4#show ospf aggregation OSPF Area Aggregation Settings Area ID Aggregated LSDB Advertise Netw ork Address Type ------------ --------------------- -------------- ------------- ...

  • D-Link TM DES-6500 - page 317

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show ospf lsdb Command: show ospf lsdb Area LSDB Advertisi ng Link State Cost Sequence ID Type Router ID ID Number ----------- -------------- ------------------ ------------------ ------- ----------------- 0.0.0.0 RTRLink 50.48.75.73 50.48.75.73 * 0x80000002 0.0.0.0 Summa ...

  • D-Link TM DES-6500 - page 318

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual show ospf virtual_neighbor Parameters <area_id> − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. <neighbor_id> − The OSPF router ID for the neighbor. This is a 32-bit number in the form of an ...

  • D-Link TM DES-6500 - page 319

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ospf ipif metric <value 1-65535 > − The interface metric (1 to 65535). Entering a 0 will allow automatic calculation of the metric. authentication – Enter the type of authent ication preferred. The user may choose between: metric <value 1-65535> − This field ...

  • D-Link TM DES-6500 - page 320

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ospf all interval between the transmission of OSPF Hello packets, in seconds. Between 1 and 65535 seconds can be specified. The Hello Interval, Dead Interval, Aut horization Type, and Authorization Key should be the same for all routers on the same network. dead_interval < ...

  • D-Link TM DES-6500 - page 321

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual To display the current OSPF interface settings, for a specific OSPF interface: DES-6500:4#show ospf ipif ipif2 Command: show ospf ipif ipif2 Interface Name: ipif2 IP Address: 123.234.12.34/24 ((Link Up) Netw ork Medium Type: BROADCAST Metric: 1 Area ID: 1.0.0.0 Administrative State: ...

  • D-Link TM DES-6500 - page 322

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual create ospf virtual_link Purpose Used to create an OSPF virtual interface. Syntax create ospf virtual_link <area_id> <neighbor_id> {hello_interval <sec 1-65535> | dead_interval <sec 1-65535> | authentication [none | simple <passw ord 8> | md5 <key_id ...

  • D-Link TM DES-6500 - page 323

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config ospf virtual_link Purpose Used to configure the O SPF virtual interface settings. Syntax config ospf virtual_link <area_id> <neighbor_id> {hello_interval <sec 1-65535> | dead_interval <sec 1-65535> | authentication [none | simple <passw ord 8> | ...

  • D-Link TM DES-6500 - page 324

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual delete ospf virtual_link Purpose Used to delete an OSPF virtual interface. Syntax delete ospf virtual_link <area_id> <neighbor_id> Description This command will delete an OSPF virtual interface from the Switch. Parameters <area_id> − A 32-bit number in the form o ...

  • D-Link TM DES-6500 - page 325

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual DES-6500:4#show ospf virtual_link Command: show ospf virtual_link Virtual Interface Configuration Transit Virtual Hello Dead Authentication Link Area ID Neighbor Router Interval Interval Status --------------- ---------------------- ------------ ----------- -------------------- ---- ...

  • D-Link TM DES-6500 - page 326

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 43 J UMBO F RAM E C OMM ANDS Certain switches can support jum bo frames (fram es larger than the standard Ethernet frame size of 1518 bytes). To transmit frames of up to 9216 byt es (and 9220 bytes tagged), the user can increase the maxim um transmission unit (MTU) size from the def ...

  • D-Link TM DES-6500 - page 327

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Example usage: To enable the jumbo fram e function on the Switc h: DES-6500:4#disable jumbo_frame Command: disable jumbo_frame Success. DES-6500:4# show jumbo_frame Purpose Used to show the status of the jumbo frame function on the Switch. Syntax show jumbo_frame Description This co ...

  • D-Link TM DES-6500 - page 328

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 45 C OMM AND H ISTOR Y L IST The command history list com mands in the Co mm and Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters ? {<command>} show command_history config command_history <value 1-40> Each ...

  • D-Link TM DES-6500 - page 329

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config authen_application CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a All Example usage: To display the parameters for a specific comm and: DES-6500:4#? config stp Command:? config stp Command: config stp Usage: {maxage <value 6-40> | maxhops <value1-20> | hel ...

  • D-Link TM DES-6500 - page 330

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual config command_history Purpose Used to configure the command history. Syntax config command_history <v alue 1-40> Description This command is used to configure the command history. Parameters <value 1-40> − The number of previously executed commands maintained in the b ...

  • D-Link TM DES-6500 - page 331

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual A T ECHNICAL S PECIFICA TIONS Physical and Environmental AC inputs & External Redundant Pow er Supply 100 - 240 VAC, 50/60 Hz (internal universal power supply) Pow er Consumption 296W DES-6504: 30W maximum DES-6505: 20W maximum DES-6508: 27W maximum DES-6511: 296W maximum DES-65 ...

  • D-Link TM DES-6500 - page 332

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual Performance Transmission Method Store-and-forward-L3 Routing RAM Buffer 256 MB per Linecard, 256MB on CPU Card. Filtering Address Table 16 K MAC addresses per device 3K IP addresses per device Packet Filtering/ Forw arding Rate Full-wire speed for all connections. 148,810 pps per po ...

  • D-Link TM DES-6500 - page 333

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual General Standard IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.1D Spanning Tree IEEE 802.1w Rapid Spanning Tree IEEE 802.1s Multiple Spanning Tree IEEE 802.1 P/Q VLAN IEEE 802.1p Priority Queues IEEE 802.1x Port and MAC Based Access Control I ...

  • D-Link TM DES-6500 - page 334

    xStack DES-6500 Modular Layer 3 Chassis Ethernet Switch CLI Manual 331 ...

Manufacturer D-Link Category Switch

Documents that we receive from a manufacturer of a D-Link TM DES-6500 can be divided into several groups. They are, among others:
- D-Link technical drawings
- TM DES-6500 manuals
- D-Link product data sheets
- information booklets
- or energy labels D-Link TM DES-6500
All of them are important, but the most important information from the point of view of use of the device are in the user manual D-Link TM DES-6500.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals D-Link TM DES-6500, service manual, brief instructions and user manuals D-Link TM DES-6500. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product D-Link TM DES-6500.

Similar manuals

A complete manual for the device D-Link TM DES-6500, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use D-Link TM DES-6500 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of D-Link TM DES-6500.

A complete D-Link manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual D-Link TM DES-6500 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the D-Link TM DES-6500, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the D-Link TM DES-6500, that we can find in the current document
3. Tips how to use the basic functions of the device D-Link TM DES-6500 - which should help us in our first steps of using D-Link TM DES-6500
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with D-Link TM DES-6500
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of D-Link TM DES-6500 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning D-Link TM DES-6500?

Use the form below

If you did not solve your problem by using a manual D-Link TM DES-6500, ask a question using the form below. If a user had a similar problem with D-Link TM DES-6500 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)