-
Planet DVR-1670 - page 1
Page 1 4/16-Channel H.264 Digital V ideo Recorder DVR-470 DVR-1670 USER’S MANUAL ...
-
Planet DVR-1670 - page 2
Page 2 Copyright Copyright © 2007 by PLANET T echnology Corp. All rights reserved . No part of thi s publication may be repro duced, transmitted, tra nscribed, stored in a retrieval system, or translated into any language or computer language, in any form or by an y means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, w ...
-
Planet DVR-1670 - page 3
Page 3 Federal Communication Commission (FCC) Radiation Exposure S tatement This equipment complies with FCC radiation expo sure set forth for an uncontrolled environment. In order to avoid the possibility of ex ceeding the FCC radio frequency expo sure limits, human proximity to the antenna shall not b e less than 20 cm (8 inches) during normal op ...
-
Planet DVR-1670 - page 4
Page 4 Content Chapter1 Produc t Introduction.................................................................................................. 6 1.1 Summary ................................................................................................................... 6 1.2 Features ............................................................. ...
-
Planet DVR-1670 - page 5
Page 5 5.18 T ransaction Inform ation .......................................................................................... 76 Chapter6 Utili ties .................................................................................................................... 80 6.1 Save Parameters .......................................................... ...
-
Planet DVR-1670 - page 6
Page 6 Chapter1 Pr oduct Intr oduction 1.1 Summary DVR-470/DVR-1670 H .264 network dig ital video recorder is an excellent d igital surveillance p roduct. It uses the embedde d MCU and real time opera ting system, combining the most advanced technology in Inform ation Industry such as video an d audio encoding/decodin g, hard disk record and TCP/IP ...
-
Planet DVR-1670 - page 7
Page 7 z Support cycle or none cycle record. z Support backup the record ed files and clips. Support USB mem o ry , USB HD D, USB CD-R/W , USB DVD-R/W , IDE CD-R/W and IDE DVD-R/W . Preview and playback z Support analog m onitor and VGA output. z Support multiple preview modes. z Support sensitive area m ask. z Support camera spiteful block alarm. ...
-
Planet DVR-1670 - page 8
Page 8 Chapter2 Installation Warning：Before you inst all the DVR, please ma ke sure the power of DVR is off. 2.1 Checking the DVR and It s Accessories When you get the pro duct, check that all the item s are included in your product pac kage. There is a list in the package. If any of the items is m issing, please contact your dea ler . 2.2 HDD In ...
-
Planet DVR-1670 - page 9
Page 9 2.3 Rear Panel Description Notice ： Pl ea se re fe r to rea l p r oduct for different model. DVR-470 Rear Panel DVR-1670 Rear Panel Index Physical Interface Description 1 V ideo Input St a nd a r d BN C . V ideo Output Connect monitor , output video and menu. 2 Audio Output 1 channel RCA (1.0 Vp-p, 75 Ω ) 3 Audio input 4 channel RCA (1.0 ...
-
Planet DVR-1670 - page 10
Page 10 External Alarm Input 4/8/16 Alarm in. Relay Output 2/4 Alarm out 8 AC Input 100V~240V AC 2.4 External Alarm In/Out Connection Alarm input port ： G (GND) ： Conenct the GND of sensor . 1~16 ： Alarm input , support normal open/norm al close. 0 ： Reserved. Alarm outp ut ： 1G~4G ： 4 relay out put. Alarm output connection Please note ...
-
Planet DVR-1670 - page 11
Page 1 1 Chapter3 Operational Instructions 3.1 Front Panel n o p q r Index T y pe Name Description 1 Sta t e Lamps READY ST A TUS ALARM RECORD NETWORK DVR is ready . Green means you can use I R re mote control. Red means there is alarm . T wink le in red means readin g or writing HDD. Network status. 2 Lamp IR receiver . Numeric Keys Input number , ...
-
Planet DVR-1670 - page 12
Page 12 REC PTZ PREV A SHIFT 1. Manual record; 2. 【 SHOT 】 in PTZ control (adjust preset). 1. Enter into PTZ co ntrol mode; 2. 【 IRIS- 】 in PTZ control.. 1. Multi screen p review switch; 2. Switch menu mode into preview; 【 FOCUS- 】 in PTZ control. 1. Input switch (number , lower case, upper case and symbol); 2. 【 FOCUS+ 】 in PTZ con ...
-
Planet DVR-1670 - page 13
Page 13 3.2 IR Controller Index Name Description 1 POWER T urnoff device. 2 DEV Enable/Disable IR rem ote control 3 Numeric Keys Same as num eric keys of front panel. 4 EDIT Same as EDIT key of front panel. 5 A Same as A key of front panel. 6 REC Same as REC key of fro nt panel. 7 PLA Y Same as PLA Y key of front panel. 8 INFO Same as INFO key of f ...
-
Planet DVR-1670 - page 14
Page 14 15 Reserved 16 F1 Same as 【 F1 】 key of front panel. 17 Lens control IRIS, FOCUS ZOOM for lens control. 18 F2 Same as 【 F2 】 key of front panel. Loading the batteries into the IR contr oller 1. Remove the ba ttery cove r . 2. Insert the battery . Please take care that the poles (+ a n d -) are correctly positioned. 3. Replace the ba ...
-
Planet DVR-1670 - page 15
Page 15 3.3 Menu Description 3.3.1 Menu Items Menu Name Function Menu Name Function Display Unit name Device ID Require password Screen saver V ideo standar d Brightness Menu transparency VGA resolution DST Date and T ime Image Camera name and position set up Adjust Brightness, Contrast, Hue and Saturation OSD Display mode, position an d OSD format ...
-
Planet DVR-1670 - page 16
Page 16 Tr a n s a c t i o n T ext input mode A TM IP address A TM type T ext inform ation Utilities Restore parameters Upgrade firmware HDD management Clear alarm output Reboot Power off V iew log System information 3.3.2 Menu Operation How to enter into menu mode z Press 【 MENU 】 key to enter into DVR main menu. z Press 【 PLA Y 】 short ke ...
-
Planet DVR-1670 - page 17
Page 17 Each menu contai ns different kinds of items. There is a small rectangular fra me named “Active Frame” whic h is pointing to the s elected item. This “ Active Frame” can be moved by 【 Æ 】 or 【 Å 】 keys. There are such kinds of menu ite ms ： 1. Check Box ： Provide 2 options, “ 9 ” means enable and “ × ” means d ...
-
Planet DVR-1670 - page 18
Page 18 3.4 Character Input In the menu interfac e , if you enter into edit sta t us (for example, in the “ camera name” edit box), at the bottom of screen, the input status is appeared ： Here it means you ca n press numeric keys to input d igital number . Press 【 A 】 key to change inp ut methods. Y ou can select “num ber”, “Upperca ...
-
Planet DVR-1670 - page 19
Page 19 Chapter4 Basic Operation Guide 4.1 Power on Note ： Please make sure the power suppl y matches DVR and AC cable connected correctly . Before switch DVR o n, please connect one monitor with V OUT or VGA interface. Otherwise, you can not see gra phic user interface and can not operate. If 【 POWER 】 lamp is off, please do as followin g ? ...
-
Planet DVR-1670 - page 20
Page 20 Camera record status is foll owing ： Icon Icon Color S tatus Description White No video signal Y ellow Vdieo input Pink Manual recording Green Real time recording Blue Motion detect recording Red External alarm recording ...
-
Planet DVR-1670 - page 21
Page 21 Ca mera alarm status is followi ng ： Icon Icon Color S tatus Description White V ideo signal lost Y ellow V iew tampering alarm Pink Motion&External alarm Green No alarm Blue Motion alarm Red External alarm Press numeric keys to switch over indi vidual camera preview . If DVR has less than 10 channels, press one numeric key to switch ...
-
Planet DVR-1670 - page 22
Page 22 4.3 User name and p assword Note ： When DVR is delivered from f a ctory , there is only one default administrator named “admin”, and password is “12345” . The admi nistrator’s name can not be modified, while the passwor d can be modified. The ad ministrator can create 15 users and define their user rights. Login Login dialog i s ...
-
Planet DVR-1670 - page 23
Page 23 Setp 2 ： Enter into password modificati on menu Move the “Ac tive Frame” to “ Password” icon by using 【 Æ 】 / 【 Å 】 keys. Press 【 ENTER 】 key to enter into fo llowing password menu ： Ste p 3 ： Input new password Press 【 EDIT 】 key to enter into e dit box. Y ou can use num eric keys to input new password. The ...
-
Planet DVR-1670 - page 24
Page 24 4.4 PTZ Control Note ： The user must have the “PTZ control” right. PTZ contr o l interface In preview mode, press 【 PTZ 】 key , i n the login dialo g, select one user name and input the correct password, you can e n ter into PTZ control interface. In menu mode, press 【 PTZ 】 key , you can enter into PTZ control i nterface dire ...
-
Planet DVR-1670 - page 25
Page 25 Adjust preset description In PTZ control mode, press 【 REC/SHOT 】 key , and press the preset number (three num eric keys), DVR will adjust t he corresponding preset num ber . Repeat pressing 【 REC/SHOT 】 key , and press the preset number , DVR will adjust that preset number . When you exit PTZ contr ol mode, the camera will stay at ...
-
Planet DVR-1670 - page 26
Page 26 4.5 Manual Record Note ： The user must have the corresponding right, DVR has HDD and HDD is formatted already . Manual record In preview mode, press 【 REC 】 key , in the pop-up login dia log, select the name and inp ut the correct password, you can e nter into the “Manual Record” interface. In menu mode, press 【 REC 】 key to e ...
-
Planet DVR-1670 - page 27
Page 27 4.6 Playback Note ： The user must have “P layback” right. Playback interface In preview mode, press 【 PLA Y 】 key , in the pop-up lo gin dialog, select username and in put correct password, you c an enter into “P layback” interface. In menu mode, press 【 PLA Y 】 key , you can enter into “Playback” interface directly . ...
-
Planet DVR-1670 - page 28
Page 28 Play by T ime ： Playback the recorded stream directly based on the time section. Select Page ： In the file l ist box, each page will only display 8 files. If the matched files are more than 8, you can select page to list o ther files. 500 pages (4000 fi les) can be searched in one time. Y ou can use numeric keys or 【↑】 【↓】 k ...
-
Planet DVR-1670 - page 29
Page 29 3. Search by Card No and Playback file ： In the playback interface, select channel number , record type, enable card No. search option (“ 9 ”) and input the card number , move “ Active Frame” to “Search” butt on, press 【 ENTER 】 key , DVR will search and list the m atched files. If the matched files are m ore than 8, you c ...
-
Planet DVR-1670 - page 30
Page 30 Exit playback In playback interface, press 【 ESC 】 key to enter into preview mode. In playback interface, press 【 MENU 】 k ey to enter into main menu, press 【 REC 】 key to enter into manual record, and press 【 PTZ 】 key to enter into PTZ con trol mode. ...
-
Planet DVR-1670 - page 31
Page 31 4.7 Backup Recorded Files Note ： The user must have “Playback” right. Pl ease connect with ba ckup devices before you start to backup. In the playback interface, you can bac k up the recorded files. In the preview m ode, press 【 PLA Y 】 key , in the login dialog, select usern a me and inpu t the correct password, you can e n ter i ...
-
Planet DVR-1670 - page 32
Page 32 St e p 2 ： Select the files that you want to backup In the file list box, use 【↑】 or 【↓】 keys to move the scrol l bar . When the scr oll bar stays at the file you w an to backup, press 【 EDIT 】 key to select it. The symbol “ 9 ” is the selection tag. Y ou can use the same method to s elect other files you want to backu ...
-
Planet DVR-1670 - page 33
Page 33 4.8 Shut Down DVR Note ： Do not switch off the power d irectly in ca se of damaging H DD. The correct step is using “Power Off” in the “Utilities” menu, or 【 POWER 】 key on the front panel or on IR controller . Shut down DVR normally Use menu Enter into “Utiliti es” menu, move “Active Frame” to “Power Off” button a ...
-
Planet DVR-1670 - page 34
Page 34 Chapter5 Parameters Setup Guide Only the users that have “ Para meters Setup” righ t ne ed read this chapte r . When the following parameters are modified and saved, you must reboot the DVR to m ake the new parameters take into ef fective. Other parameters do not need to reboot. z Any network param eters z Stream type, resolution and re ...
-
Planet DVR-1670 - page 35
Page 35 Move “Active Frame” to “ User” icon, press 【 ENTER 】 key to enter into “User Managem ent” menu. In the user name list b ox, only “admin” is existed. Y ou can use 【→】 key , move “Active Frame” to passw ord edit box, and press 【 EDIT 】 key to enter into edit status. Press numeric keys to input the new passwor ...
-
Planet DVR-1670 - page 36
Page 36 5.2 Add and Delete User Enter into “User Manag ement” interface. Add user The steps are following ： St e p 1 ： Enter into “User Manage ment” menu Please refer to chapter 5.1 St e p 2 ： Add new user name In the “User Manag e ment” m enu, move “A ctive Fram e” to “Add” button and press 【 ENTER 】 , in the pop-up d ...
-
Planet DVR-1670 - page 37
Page 37 In the users list box of “User Management” menu, use 【 Ç 】 【 È 】 keys to s elect the new user name, then us e 【 Æ 】 key to “Default R ights” button, press 【 ENTER 】 , the user will have the default rights. The default rights incl ude local playback, rem ote playback and view log. If you want to define the detail r ...
-
Planet DVR-1670 - page 38
Page 38 “Remote Rights” ： PTZ Control ： Remote control PTZ ; Record ： Remote m anual start/stop recording; Playback ： Remote playback, download the recorded files on DVR; Parameters Setup ： Remote setup t he DVR parameters; Log ： Remote view the log on DVR; Utilities ： Remote upgrade firm ware, format HDD, reboot DVR and shut down ...
-
Planet DVR-1670 - page 39
Page 39 5.3 Unit Name and Device ID Unit name In the “Display” m enu ： There is an item nam ed “Unit Name”. The default unit name is “ E mbedded Net DVR”. Move “Active Frame” to unit name edit box, press 【 EDIT 】 key to enter into edit status, you can modify the unit nam e. About how to input characters, pleas e refer to chapt ...
-
Planet DVR-1670 - page 40
Page 40 5.4 V ideo Output St andard and VGA Setup V ideo output standard There is one VOUT BNC connector at the rear panel of DVR. It is used to connect with analog monitor an d can support P AL or NTSC video output. Y ou can modify video o utput standard to match video input. In “Display” menu ： There is a list box nam ed “V ideo Output St ...
-
Planet DVR-1670 - page 41
Page 41 5.5 OSD Setup OSD is abbrevia tion of “On Screen Display ” . For our embedded DVRDVS, it includ es displaying system time and cam era name. OSD settings include ： System time, time format, tim e display position, camera name, cam era name display posi tion, etc. System Time In “Display” m enu, you can setup DVR system date and tim ...
-
Planet DVR-1670 - page 42
Page 42 Display mode ： There are several display modes ： Opaque&S teady , T ransparent&Steady , T ransparent&Flashing, Opaque&Flashing, Move “Active Frame” to “ OSD” item, you can select one mode. Display position and format ： Move “ Active Frame” to “Position” button on the ri ght side of “OSD”, press 【 ...
-
Planet DVR-1670 - page 43
Page 43 Chapter 3.4). The camera name can support 32 charact ers. St e p 3 ： Press 【 ENTER 】 key to exit edit status. Move “Active Fram e” to “Confirm” button, press 【 ENTER 】 to save the modificati on and you can see the new cam era name. Press “Cancel” button or 【 ESC 】 key t o abort. Setup Camera Name Position If you do ...
-
Planet DVR-1670 - page 44
Page 44 5.6 V ideo Parameters Setup For different camera and different background, in order to get the best video image, you need to adjust video p arameters such as brightenss, saturation , contrast and hue, etc. Y ou can setup the camera individu ally , and also you c an copy the video parameters of one camera to any ot her ca meras. Here are the ...
-
Planet DVR-1670 - page 45
Page 45 5.7 Mask Area Setup In some cases, maybe you want m ask the sensitive area. This area will not be preview and recorded. The mask area setup steps are following ： St e p 1 ： Enter into “Image Setup” menu ： St e p 2 ： Select one camera ： Y ou can use 【 Ç 】 【 È 】 keys to select one camera. St e p 3 ： Enter into mask a ...
-
Planet DVR-1670 - page 46
Page 46 (22*15 for NTSC), you c an use 【↑】 【↓】 【→】 【←】 keys to m ove the yellow pane to your hope posi tion and press 【 EDIT 】 ke y , the yellow pane wi ll be turned into red, then you can us e 【↑】 【↓】 【→】 【←】 keys to extend the red pane. This red area is the mask area. After you make sure the red ...
-
Planet DVR-1670 - page 47
Page 47 5.8 V iew T ampering Alarm If you enable t his function, when someone blocks the camera spitefully , DVR will make warning alarm. St e p 1 ： Enter into “Image Setup” memu ： St e p 2 ： Select camera ： Please use 【 Ç 】 【 È 】 keys to select one cam era. St e p 3 ： Select sensitivity ： Y ou can use 【↑】 【↓】 ...
-
Planet DVR-1670 - page 48
Page 48 St e p 6 ： Alarm schedule setup ： When there is view tampering alarm happene d, DVR will handle the a larm based on the schedu le. Y ou can set 4 per iods for each day one week. Also you can copy the schedule of one day to other days. Notes ： T ime periods can not be repeated. Please re b oot DVR to mak e the paramete rs into effectiv ...
-
Planet DVR-1670 - page 49
Page 49 5.9 V ideo Loss Alarm When the video c able or camera has something wrong, the video image is lost. If y ou enable video loss alarm , in such case, DVR will make alarm. St e p 1 ： Enter into “Image Setup” menu ： St e p 2 ： Select camera ： Use 【 Ç 】 【 È 】 keys to select one cam era. St e p 3 ： Enter into “V ideo Sig ...
-
Planet DVR-1670 - page 50
Page 50 St e p 5 ： Setup alarm policy ： Y ou can select one or m ore response solutions, including “On Screen W arning”, “Audible W arning”, “ Upload to Center” and “T rigger Alarm Output”. Y ou can use 【↑】 【↓】 and 【 EDIT 】 key to enable or disabl e them. “ × ” is disable and “ 9 ” is enable. St e p 6 ? ...
-
Planet DVR-1670 - page 51
Page 51 5.10 Motion Detection Alarm If you enable this functio n, when there is motion detected, DVR wi ll make alarm. St e p 1 ： Enter into “Image Setup” menu ： St e p 2 ： Select camera ： Use 【 Ç 】 【 È 】 key to select one camera. St e p 3 ： Select motion dete ction sensitivity ： On the right side of “Motion Det. Level? ...
-
Planet DVR-1670 - page 52
Page 52 The whole screen is divi ded into 22*18 pan es (NTSC ： 22*15). There is one yellow panel on the upper left side. The motion area setup steps are the s a me as that of m ask area setup (refer to chapter 5.7). The only differences are that you can use 【 PTZ 】 key to set the whole screen as motion area, and m util motion areas can be def ...
-
Planet DVR-1670 - page 53
Page 53 St e p 6 ： Motion alarm record channel setup ： When there is motion alarm happ ened, you can trigger relate d camera to start recording. In “Motio n Alarm Handle” menu, yo u can select one or more record channel s. Please use 【 ENTER 】 or 【 EDIT 】 key to enabl e the flag into “ 9 ”. Note ： In order to make the cam eras ...
-
Planet DVR-1670 - page 54
Page 54 5.1 1 Preview Properties In “Preview” m enu, you can setup previe w mode, screen sw itch time, enable or disable audio preview and preview layout. St e p 1 ： Enter into “Pre view” menu ： In the main menu, move “ Active Frame” to “Preview” icon and press 【 ENTER 】 , you can enter into “preview” menu. St e p 2 ： ...
-
Planet DVR-1670 - page 55
Page 55 Preview layo ut setup ： There is a square frame divided in to many windows. If you select “4 Screen”preview m ode, this fram e is divided into 4 win dows. Each wind ow represents one camera. Y ou can move “Active Fram e” among the windows. Th ere is one bar under the square to display the pre view order of all cameras. First selec ...
-
Planet DVR-1670 - page 56
Page 56 5.12 Recording Setup In main menu, there is an i con named “Recording”. Y ou can enter into recording m enu as following ： “Recording” menu description ： If HD Full ： There are two options ： “Overwrite” and “S top recording”. If you selec t “Overwrite” option, when all HDDs in DVR are full, DVR will overwrite the ...
-
Planet DVR-1670 - page 57
Page 57 If you select varia b le bit rate, DVR will adjust the actual bit rate according to the video movement. When there is not m uch movement, DVR will use low bit rate, while there is much movement, DVR will u se high bit rate . In this case, DVR can save HDD usage and network bandwidth. If y ou select fixed bit rate, DVR will use the fi xed bi ...
-
Planet DVR-1670 - page 58
Page 58 Note ： When the camera’ s recording schedule is m odified, you must reboot DVR to make it into effe ctive. All day reco rding setup ： St e p 1 ： Enter into r ecording schedule menu In recording m enu, use 【 ENTER 】 or 【 EDIT 】 key to enable record function (“ 9 ” flag), press “Schedule” butto n to enter into recordin ...
-
Planet DVR-1670 - page 59
Page 59 St e p 1 ： Enter into r ecording schedule menu In recording m enu, use 【 ENTER 】 or 【 EDIT 】 key to enable record function (“ 9 ” flag), press “Schedule” butto n to enter into recording schedul e menu. St e p 2 ： Select ond day and disable all day r ecording option For “Day” item, there are options ： Monday , Tuesd ...
-
Planet DVR-1670 - page 60
Page 60 5.13 External Alarm Input and Relay Output For DVR-470, there are 4 external alarm inpu t and 2 relay out put. For DVR-1670, there are 16 external alarm input and 4 relay output. In “Alarms” menu, you can setup for each external alar m input. In main menu, m ove “Active Frame” to “Alarm s” icon and press 【 ENTER 】 key to ent ...
-
Planet DVR-1670 - page 61
Page 61 St e p 4 ： Alarm trigger r ecord channel setup Y ou can sele ct channels to record for each alarm input. In the sub menu, y ou can use 【 ENTER 】 or 【 EDIT 】 key to enable recor d channel. “ × ” means disable and “ 9 means enable. Note ： In order to trigger the chan nel to record, in “Recording” m enu, you must enable ...
-
Planet DVR-1670 - page 62
Page 62 First select one camera, the n select one of following PTZ linka ge ： z Preset ： Set the flag as “ 9 ” to enable preset, in the preset num ber edit box and input one preset number that has been setup already . Please refer to chapter 5.15 for preset setup. z Sequence ： Set the flag as “ 9 ” to enable sequence and in put one se ...
-
Planet DVR-1670 - page 63
Page 63 St e p 3 ： Enter into alarm out schedule Y ou can set the s chedule to make alarm output into effective. M ove “Active Frame” to “Schedule” bu tton on right s ide of “Alarm Out T ime” ite m, press 【 ENTER 】 key to enter into the corresponding schedule m enu ： St e p 4 ： Setup alarm out schedule Like other schedule set ...
-
Planet DVR-1670 - page 64
Page 64 5.14 Network Parameters If you want use ne twork to access DVR, you m u st setup network p arameters. Note ： If any network parameter is modified, you m ust save and reboot DVR to make it into effective. In main menu, m ove “Active Frame” to “N etwork” icon and press 【 ENTER 】 , you can enter into “Network” menu as fol low ...
-
Planet DVR-1670 - page 65
Page 65 This DNS is special s oftware, not the normal dom ain name server . Y ou can use the provided SDK to develop this DNS software. Multicast IP ： It is one D-class IP address, am ong 224.0.0.0 --- 239.255.255.255. If you do not use m ulticast function, you do n ot need to set. Some routers will prohibit multicast function in case of n etwork ...
-
Planet DVR-1670 - page 66
Page 66 PTZ menu description Select channel ： Select one PTZ camera. RS-485 parameters ： Incl uding baudrate, data bit, stop bit, parity , flow control, etc. These parameters must be the same as those of P TZ. Protocol. PTZ address ： Each PTZ h a s one dif ferent address. PTZ type ： DVR had the following PTZ protoc ol ： Y ouLi, LinLin-101 ...
-
Planet DVR-1670 - page 67
Page 67 Cruise setup ： Cruise is remem b ering the track of P TZ m ovement. Please make sure the PTZ you are using can s upport cruise function. Preset setup In “ PTZ” menu, m ove “Active Frame” to “Setup” button on t h e right side of “Preset” item, press 【 ENTER 】 , you can enter in to “Preset” setup menu ： Add preset ...
-
Planet DVR-1670 - page 68
Page 68 In “Sequence” setup menu, first input the se quence num ber . The sequence is among 1 --- 16. Each sequence is m ade up of cruise points, and each c ruise point includes preset num ber, dwell time and dwell s peed. Dwell time is the time stay ing at that preset number . Dwell speed is the speed that PTZ is m oved to that preset number . ...
-
Planet DVR-1670 - page 69
Page 69 Press “RecCru” button, you will e nter into “PTZ contro l” interface. Y ou can start controlling PTZ with direction keys, press 【 ENTER 】 to save the operation tr ack and return “Cruise” setup menu. Press “S tartCru” button to repeat th e PTZ track until you press “S top” button. Press “Return” button ba ck to ? ...
-
Planet DVR-1670 - page 70
Page 70 5.16 RS232 setup There is one RS-232 port at DVR rear pane l. In main menu, move “Active Fram e” to “RS232” icon and perss 【 ENTER 】 key , you enter into “RS232” setup menu ： RS232 menu description RS-232 parameters ： Incl uding baud rate, data bit, sto p bit, parity , flow control, etc. Wo r k m o d e ： The RS-232 can ...
-
Planet DVR-1670 - page 71
Page 71 Username, password and V erify passw ord ： Only used when work mode is “PPP”. Used for login when remot e PC dialup throug h PSTN. Phone ： Only used when work m ode is “PPP” and PPP mode is “Active”. It is the phone number of remote PC. Callback and Data Encryption ： O nly used when work mode is “PPP”. They are not ava ...
-
Planet DVR-1670 - page 72
Page 72 St e p 3 ： Save setup In “Recording” menu, press “Conf irm” button to save param eters. St e p 4 ： Setup Modem used on DVR side Use DCE calbe to connect Modem with PC serial port. Y ou can use HyperT erminal or NetT erm to setup modem ： A T&F ---- Retore default parameters (Gen erally , Modem is hard flow control) A T& ...
-
Planet DVR-1670 - page 73
Page 73 ...
-
Planet DVR-1670 - page 74
Page 74 St e p 3 ： Establish the dialup connection Select the Modem connected with PC just like the d ialup network connection, input the telephone nu mber connected with DVR’ s modem. Input the user name, password. They m ust be the same as that DVR PPP setup. St e p 4 ： During the dialup connection , it will give th e message of “verifica ...
-
Planet DVR-1670 - page 75
Page 75 5.17 Exceptions The exceptions can be handled at present include ： hard disk full, hard disk error, illegal access, IP address conflict, network fai l ure, and NTSC/P AL dif fer . Enter into “Excep tions” menu ： Including the foll owing handl e methods ： Audible W arning ： DVR beep warning. Upload to Center ： Send exception in ...
-
Planet DVR-1670 - page 76
Page 76 5.18 T ransaction Information The DVR can actively obtain or passively recei ve the credit card number from A TM machine linked throug h network or serial port, and credit card num ber can be overlay on live video, recorded and play back. The following descript ion indicates how to carry o ut relevant parameter setting ac cording to differe ...
-
Planet DVR-1670 - page 77
Page 77 Start & e nd position an d length of transaction type T ransaction type and c ode When the A TM machine is sending transaction i n formation to bank center , DVR will capture the data packa ge through network, and analys e the data according to the format. Then DVR will overlay the corres pond text on live video. 2. Network r eceive ： ...
-
Planet DVR-1670 - page 78
Page 78 In the case, you m ust set the RS-232 of DVR as transparent channel m ode as following ： A software must be run in the A TM machine, and send the credit c ard number , transaction code to DVR through RS-232 port. Please provide deta il A TM machine com munication protocol for act ual projects. 4. Receive the command sent by A TM through s ...
-
Planet DVR-1670 - page 79
Page 79 In the case, you m ust set the RS-232 of DVR as transparent channel m ode as following ： Also, a software must be run in A TM machine, and send command to DVR through RS-2 32 port based on special communi cation protocol. ...
-
Planet DVR-1670 - page 80
Page 80 Chapter6 Utilities There are man y tools in “Uti lities” men u. Includi ng “SavePar a”, “Resto rePara”, “Upg rade”, “Hard Disk”, “Stop Alarm Out”, “Reboo t”, “Power Off”, “V iew Log” a nd “System Info ”. Enter into “Utili ties” menu ： 6.1 Save Parameters Save factory default param eters into FLA ...
-
Planet DVR-1670 - page 81
Page 81 6.3 Upgrade Y ou can use this function to upgrad e the firm ware. Pleas e confirm the language is matched. Press “Upgrad e” icon, in th e pop-up dial og, you can se lect eithe r “FTP” or “USB” upgrade mode. If you select “FTP” m ode, you will enter into “FTP Upgrade” menu ： Input the ftp server IP and press 【 ENTER ? ...
-
Planet DVR-1670 - page 82
Page 82 6.4 Hard Disk Management Check HDD work status Capacity , Free space, Stand by or not, Normal status or not. Format HDD Before formatting stop all recording. After form atting, you must reboot DVR, ot herwise DVR will not work normally . 6.5 Clear Alarm Out Clear the alarm output manually . 6.6 Reboot Reboot DVR. 6.7 Power Off Shut down DVR ...
-
Planet DVR-1670 - page 83
Page 83 If you want to view the log based on default option, just press 【 ENTER 】 key . DVR will list all matched inform ation. Also you can select options to search (By T ype, By Date, By T ype&Date). By T ype T o view log information of the ass igned type. T ype is divided into “Major type” and “Minor type”. Major type in cludes o ...
-
Planet DVR-1670 - page 84
Page 84 St e p 4 ： When searching is finis hed, DVR will list all matched alarm information. In the list box, the inf ormation includ es ： Index, Occur T ime, Major T ype, Minor T ype, Panel User , Net User , Host Address, Para. T ype, Channel No, HDD No, Alarm In and Alarm Out. Y o u can press “More Info” button for more inform ation, also ...
-
Planet DVR-1670 - page 85
Page 85 6.9 System Information Press “System Info” icon in “Utilities” m enu, you can get DVR system information ： ...
-
Planet DVR-1670 - page 86
Page 86 Chapter7 Firmwar e Upgrade The DVR firmware is stored in FLAS H ROM. Y ou can use DVR upgrade functi on to write the firmware file ( digicap) into FLASH. There are two cases that you need to upgrade DVR firmware. One is update old fir mware. The other is when the code in DVR FLASH is crashed. Note ： Make sure that the DVR and the firmware ...
-
Planet DVR-1670 - page 87
Page 87 3. Select “Users/rights ” under “Security” menu item . The following dia log box will be pop-up. 4. Create new us er . Click “new user’. New user dialog pops up . Input user nam e “target”. Click “OK”. 5. In the password dial og, input password “target ” in “New Password” and “V erify Password” edit box. Cl i ...
-
Planet DVR-1670 - page 88
Page 88 6. In the “User/Rights Security ” Dialog, select “User Name” as “tar get”. In “Home Directory” edit bo x, input the path where the firm ware file (digicap) is placed. Then press “Done” to exit. 7. Next time, y ou need not setup again, just d o uble click a nd open “wftpd32.exe” to upgra de the DVR/DVS firmware. ...
-
Planet DVR-1670 - page 89
Page 89 7.2 Upgrade Mode 1. Use client software to upgrade the firm ware file. Y ou do not need t o use ftp server software. Please refer to the client softw are user manual for detail information. 2. Use “FTP” function of “U pgrade” sub menu in “Utiliti es” menu. Y ou need one host PC to run FTP server software and place firmware file ...
-
Planet DVR-1670 - page 90
Page 90 Appendix A DVR Connect Cable Definition 1 UTP network connect cable made method Material and tool One twist cable (8 pin, the length can b e defined as to t h e actual dem and, but must be within 100m), 2 standard RJ4 5 head, one tool for RJ45. Suggestion ： have a network cable t est tool to test each cable made. Pin definition T o m ake ...
-
Planet DVR-1670 - page 91
Page 91 The corresponding relationship of cr oss cable 2 RS-232 connect cable made method DVR-802x has standard DB9 RS-232 int erface, like PC COM port. Pin definition “I” means DVR input and O means DVR out put. Pin index Name I/O Description 1 DCD I Carrier Detect 2 RXD I Receive Data 3 TXD O T ransfer Data 4 DTR O T erm inal Device Ready 5 G ...
-
Planet DVR-1670 - page 92
Page 92 Appendix B Specifications Model name DVR- 470 DVR-1670 V ideo compression H.264 Preview resolution PA L ： 7 04*576 (4CIF), NTSC ： 704*480 (4CIF) Playback resolution CIF/QCIF V ideo inp ut 4 16 V ideo inp ut interface BNC (Electrical Level ： 1. 0Vp-p, resistance ： 75 Ω ) V ideo out put 1 channel, BN C (Electrical Level ： 1.0Vp-p, ...
-
Planet DVR-1670 - page 93
Page 93 Power supply 100~240V AC, 6.3A, 50~60 HZ Power consumption 20--42W (without HDD) Wo r k i n g temperature -10 ℃--＋55℃ Wo r k i n g humidity 10 ％ --90 ％ Size 14.25 inch sta ndard (440mm*390mm *70mm) We i g h t ≤ 8Kg (without HDD and CD-R/W) PA L ： 1 76*144(QCIF), 352*28 8(CIF), 704*288(2CIF), 528*384(DCIF), 7 04*576(4CIF); NTSC ...
-
Planet DVR-1670 - page 94
Page 94 Appendix C List of Recommended DVR Peripherals USB DVD-R/W ： 1. LG GSA-E10L 2. BENQ EW164B USB CD-R/W ： 1. BENQ external 5232WI-ok2 2. ASUS CR W -4824A + USB Convertor case 3. SONY CD-R/R W CRX230AD + Convertor cable 4. SONY CD-R/R W CRX225E + Convertor cable 5. BENQ external EW162I-OK2 IDE CD-R/W ： 1. Sony CD-R/R W CRX225E 2. NEC DVD ...
-
Planet DVR-1670 - page 95
Page 95 W est Digital ： 1. WD Caviar WD400BB 2. WD Caviar WD800BB 3. WD Caviar WD1200BB 4. WD Caviar WD2000BB 5. WD Caviar WD2500BB 6. WD Caviar SE WD1600BB 7. WD Caviar SE WD2000JB 8. WD Caviar SE WD2500JB 9. WD Caviar SE WD3000JB ...
-
Planet DVR-1670 - page 96
Page 96 Appendix D Quick Sear ch Function T able T y pe Name Description Index User management Create and delete users. Sy stem has one default administrator . The administrator can create 15 users and define the ir rights. 5.2 Safety function Password Management Modify password. 4.3&5.1 HDD management Format HDD, HDD information. 6.4 Recording ...
-
Planet DVR-1670 - page 97
Page 97 Remote record Remote record real time stream . * Remote playback Remote playback the recorded files in DVR * Download Download recorded files in DVR. * Remote upgrade Remote upgrade firmware. * T ransparent channel Remote control serial devi ce connected with serial port of DVR. 5.16 W eb Using IE to access DVR * PSTN Access DVR through PST ...
-
Planet DVR-1670 - page 98
Page 98 Appendix E T r oubleshooting Failure Possible reas ons After plugging in pow er, turning on the power swi tch, “POWER” light in front P anel does not turn on, and fan does not work. 1) Power cable is broken. 2) Power supply is broken. After plugging in pow er, turning on the power swi tch, “POWER” light in front pa nel turn to green ...
-
Planet DVR-1670 - page 99
Page 99 3) Old player SDK (playm 4.dll) Notes ： 1) Place the DVR in well venti lated space so that it operates within the allowed r ange of temperature and hum idity as in specification. 2) If the circuit board is wet, dust on circui t board can cause a short cir cuit. The circuit board, lug and socket , housing fan and housing should be cleaned ...
Do you have a question concerning Planet DVR-1670?
Use the form below
If you did not solve your problem by using a manual Planet DVR-1670, ask a question using the form below. If a user had a similar problem with Planet DVR-1670 it is likely that he will want to share the way to solve it.