English dropdown-ico

Manual Craftsman 316.79614

36 pages 4.02 mb
Download

Go to site of 36

Summary
  • Craftsman 316.79614 - page 1

    Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Visit our website: www .sears.com/craftsman CAUTION: Befor e using this pr oduct, r ead this manual and follow all safety rules and operating instructions. Operator’ s Manual 4-Cycle WEEDW ACKER ® GAS TRIMMER Model No. 316.796140 • SAFETY • ASSEMBL Y • OPERA TION • MAINTENANCE • ...

  • Craftsman 316.79614 - page 2

    2 SPARK ARRESTOR NOTE NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S. Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by law that certain internal combustion engines operated on forest brush and/or grass-covered areas be equipp ...

  • Craftsman 316.79614 - page 3

    3 SYMBOL MEANING • WARNING - READ OPERATOR'S MANUAL Read the operator’s manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders. SAFETY AND INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may ...

  • Craftsman 316.79614 - page 4

    4 WARRANTY STATEMENT TWO YEAR FULL WARRANTY ON CRAFTSMAN GAS TRIMMER When used and maintained according to the operator’s manual, if this gas trimmer fails due to a defect in material or workmanship within two years from the date of purchase, return it to any Sears store, other Craftsman outlet, or Sears Parts & Repair Center in the United St ...

  • Craftsman 316.79614 - page 5

    5 Cutting Attachment Shield Fuel Cap Throttle Control D-Handle HassleFree lll ™ Shaft Grip Primer Bulb Oil Fill Plug Choke Lever Spark Plug Shaft Housing Starter Rope Grip Line Cutting Blade Muffler Twist & Edge and Craftsman Convertible™ Coupler On/Off Stop Control KNOW YOUR TRIMMER Air Filter Cover ASSEMBLY INSTRUCTIONS INSTALLING AND ADJ ...

  • Craftsman 316.79614 - page 6

    RECOMMENDED OIL TYPE Using the proper type and weight of oil in the crankcase is extremely important. Check the oil before each use and change the oil regularly. Failure to use the correct oil, or using dirty oil, can cause premature engine wear and failure. Use a high-quality SAE 30 weight oil of API (American Petroleum Institute) service class SF ...

  • Craftsman 316.79614 - page 7

    7 Start/On (I) Stop/Off (O) Throttle Control Fig. 7 STARTING INSTRUCTIONS WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 8). To avoid serious injury, the operator and unit must be in a stable position while starting. WARNING: Operate this unit only in a well- ventilated outdoor are ...

  • Craftsman 316.79614 - page 8

    6. Correctly installed line will be the same length on both sides. NOTE: Do not rest the Hassle-Free III™ Cutting Head on the ground while the unit is running. Some line breakage will occur from: • Entanglement with foreign matter • Normal line fatigue • Attempting to cut thick, stalky weeds • Forcing the line into objects such as walls o ...

  • Craftsman 316.79614 - page 9

    To Install Attachments NOTE: To make installation easier, place the unit on the ground or on a workbench. 1. Make sure the unit is turned completely off. 2. Turn the knob counterclockwise to loosen the coupler (Fig. 15). 3. While firmly holding the attachment, push it straight into the coupler until the release button (Fig. 16) snaps into the prima ...

  • Craftsman 316.79614 - page 10

    10 CHECKING THE OIL LEVEL The importance of checking and maintaining the proper oil level in the crankcase cannot be overemphasized. Check oil before each use: 1. Stop the engine and allow oil to drain into the crankcase. 2. Place the engine on an elevated, level surface with the cutting head shield hanging off the surface to get a proper oil level ...

  • Craftsman 316.79614 - page 11

    11 7. Reinstall the air filter cover. Position the slots on the top of the air filter cover onto the tabs at the top of the back plate (Fig. 27). 8. Swing the cover down until the tab on the air filter backplate snaps into place in the slot on the air filter cover (Fig. 28). CARBURETOR ADJUSTMENT The idle speed of the engine is adjustable. An idle ...

  • Craftsman 316.79614 - page 12

    12 MAINTENANCE AND REPAIR INSTRUCTIONS Adjust Idle Speed Screw If, after checking the fuel and cleaning the air filter, the engine still will not idle, adjust the idle speed screw as follows: 1. Start the engine and let it run at a high idle for a minute to warm up. Refer to Starting/Stopping Instructions. 2. Release the throttle trigger and let th ...

  • Craftsman 316.79614 - page 13

    13 5. Clean the spark arrestor screen with a wire brush or replace it. 6. Reinstall the spark arrestor screen, spark arrestor diverter and screws. CLEANING Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can dam ...

  • Craftsman 316.79614 - page 14

    14 TROUBLESHOOTING NOTE: F or repairs beyond the minor adjustments listed above, contact your nearest Sears Parts & Repair center (1-800-4-MY-HOME ® ) or other qualified service dealer. CAUSE ACTION Old fuel Drain gas tank and add fresh fuel Improper carburetor adjustment Take to a Sears or other qualified service dealer for adjustment Fouled ...

  • Craftsman 316.79614 - page 15

    15 Repair Protection Agreements Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That’s when having a Repair Protection Agreement can save you money and aggravation. Purchase a Repair Protection A ...

  • Craftsman 316.79614 - page 16

    16 NOTES ...

  • Craftsman 316.79614 - page 17

    PARACHISPAS NOTA: Para los usuarios en tierras forestales de los EE.UU. y en los estados de California, Maine, Oregon y Washington. Todos los terrenos forestales de los EE.UU. y el estado de California (Códigos de Recursos Públicos 4442 y 4443), Oregon y Washington, requieren por decreto, que ciertos motores de combustión interna que se hagan fu ...

  • Craftsman 316.79614 - page 18

    • Use sólo piezas y accesorios de repuesto del fabricante del equipo original para esta unidad. Puede obtenerlos en su proveedor de servicio autorizado. El uso de piezas y accesorios que no son equipo origina; puede causar graves lesiones al operador o el daño de su unidad, y la cancelación de su garantía. • Mantenga la unidad libre de vege ...

  • Craftsman 316.79614 - page 19

    19 WARRANTY STATEMENT GARANTÍA LIMITADA POR DOS AÑOS EN EL RECORTADOR DE GASOLINA CRAFTSMAN Por dos años a partir de la fecha de compra, cuando se use y se dé mantenimiento a este Recortador según el manual del operador , Sears reparará cualquier defecto en material o mano de obra sin cargo alguno. Esta garantía excluye la bujía, el filtro ...

  • Craftsman 316.79614 - page 20

    20 NORMAS PARA UNA OPERACIÓN SEGURA Protección accesoria de corte Tapa del combustible Gatillo del regulador Manija en D Accesorio de corte Traba del regulador Bombilla del cebador Tapón del aceite Palanca del obturador Bujía de encendido Bastidor del eje Manjo del eje Cuchilla de corte de línea Silenciador Craftsman Convertible™ Coupler Con ...

  • Craftsman 316.79614 - page 21

    TIPO DE ACEITE RECOMENDADO El uso de un aceite del tipo y peso correctos en el cigüeñal es extremadamente importante. Verifique el aceite antes de cada uso y cambie el aceite con frecuencia. Si no usa el aceite correcto, o utiliza aceite sucio, puede causar el desgaste y falla prematuros del motor. Use un aceite de buena calidad SAE 30 de API (Am ...

  • Craftsman 316.79614 - page 22

    22 INSTRUCCIONES DE ARRANQUE 1. Verifique el nivel de aceite en el cárter del cigüeñal. Lea Inspección del Nivel de Aceite. 2. Llene el tanque de combustible con gasolina nueva, limpia y sin plomo. NOTA: No es necesario encender la unidad. El Control de Encendido/Apagado está en la posición de ENCENDIDO (I) en todo momento. 3. Oprima completa ...

  • Craftsman 316.79614 - page 23

    23 INSTRUCCIONES DE OPERACIÓN COMO SOSTENER EL RECORTADOR Antes de operar esta unidad, párese en posición de operación (Fig. 10). Verifique lo siguiente: • El operador tiene protección ocular y ropa adecuada. • El brazo derecho está levemente doblado, y la mano está sosteniendo el mango del eje. • El brazo izquierdo está recto, y la m ...

  • Craftsman 316.79614 - page 24

    24 INSTRUCCIONES DE MANTENIMIENTO Y REPARACIÓN INSTRUCCIONES DE OPERACIÓN ADVERTENCIA: Para evitar lesiones personales graves, nunca realice manteni-miento ni reparaciones con la unidad funcionando. Realice siempre el mantenimiento y las reparaciones con la unidad fría. Desconecte el cable de la bujía de encendido para cerciorarse de que la uni ...

  • Craftsman 316.79614 - page 25

    CAMBIO DEL ACEITE En un motor nuevo, cambie el aceite después de las 10 primeras horas de operación. Cambie el aceite mientras el motor aún está caliente. El aceite fluirá con libertad y llevará más impurezas. 1. Desenchufe el manguito de la bujía de encendido para eliminar el arranque. 2. Retire el tapón de relleno de aceite / varilla de ...

  • Craftsman 316.79614 - page 26

    2. Retire el filtro de aire (Fig. 23). 3. Lave el filtro con agua y detergente (Fig. 24). Enjuague bien el filtro y déjelo secar. 4. Aplique suficiente aceite limpio de motor SAE 30 para recubrir ligeramente el filtro (Fig. 25). 5. A priete el filtro para esparcir y retirar el exceso de aceite (Fig. 26). 6. Vuelva a colocar el filtro (Fig. 23). NO ...

  • Craftsman 316.79614 - page 27

    27 NOTA: Los ajustes descuidados pueden dañar su motor seriamente. Los ajustes del carburador deben ser realizados por un proveedor de servicio autorizado. Inspección del Combustible En general, el combustible viejo es el motivo principal para que la unidad no funcione en forma adecuada. Drene y vuelva a llenar el tanque con combustible nuevo, li ...

  • Craftsman 316.79614 - page 28

    28 5. Instale una bujía de encendido con la separación correcta en la cabeza del cilindro. Ajuste girando la llave de casquillo 16 mm (5/8 de pulgada) en sentido horario hasta que esté ajustada sin huelgo. Si usa una llave de torsión, ajuste a: 110-120 pulg.•libras (12.3-13.5 N•m) No ajuste demasiado. MANTENIMIENTO DEL AMORTIGUADOR DE CHISP ...

  • Craftsman 316.79614 - page 29

    29 INSTRUCCIONES DE MANTENIMIENTO Y REPARACIÓN 2. Arranque el motor y déjelo funcionar hasta que se ahogue. Esto asegura que toda la gasolina se haya drenado del carburador. 3. Deje enfriar el motor. Saque la bujía de encendido y coloque 1 onza (30 ml) de aceite de motor de buena calidad en el cilindro. Tire de la cuerda de arranque lentamente p ...

  • Craftsman 316.79614 - page 30

    30 MOTOR* *Toda las especificaciones contenidas en este manual se basan en la información más reciente disponible en el momento de impresión del manual. Nos reservamos el derecho de hacer cambios en cualquier momento sin aviso previo. EJE IMPULSOR Y ACCESORIO DE CORTE* Tipo de motor ............................................................... ...

  • Craftsman 316.79614 - page 31

    31 Repair Protection Agreements Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time. That’s when having a Repair Protection Agreement can save you money and aggravation. Purchase a Repair Protection A ...

  • Craftsman 316.79614 - page 32

    32 PARTS LIST 2 50 49 48 3 52 47 46 51 43 41 40 39 38 37 36 35 34 36 45 44 14 16 15 7 8 18 17 13 12 22 23 21 6 19 4 3 24 3 25 26 27 3 29 28 30 31 33 31 2 3 9 10 3 11 5 53 32 42 3 1 20 REPLACEMENT PARTS - MODEL 316.796140 4-CYCLE GAS TRIMMER ...

  • Craftsman 316.79614 - page 33

    33 PARTS LIST REPLACEMENT PARTS - MODEL 316.796140 4-CYCLE GAS TRIMMER Item Part No. Description 1 753-05206 Engine Cover Assembly (includes 2 & 3) 2 753-04595 Cover Screw 3 753-05208 Screw 4 753-05209 Rocker Cover 5 753-05210 Rocker Cover O-Ring 6 753-05228 Cylinder Assembly (includes 3, 5 & 9) 7 753-05229 Piston Ring Assembly 8 753-05230 ...

  • Craftsman 316.79614 - page 34

    34 PARTS LIST 16 25 23 22 4 9 7 Item Part No. Description 1 753-04234 Throttle Housing Assembly (includes 2-4) 2 753-04119 Throttle Trigger 3 791-182690 Throttle Trigger Spring 4 791-182405 Switch Assembly 5 753-05266 Throttle Cable Assembly 6 753-04344 Upper Drive Shaft Housing 7 791-180869 Deluxe D-Handle Assembly (includes 8-10) 8 791-181070 Scr ...

  • Craftsman 316.79614 - page 35

    35 NOTA ...

  • Craftsman 316.79614 - page 36

    36 Get it fixed, at your home or ours! Y our Home For repair— in your home —of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’ s manuals that you need to do-it-yourself. For Sears professional installation of ...

Manufacturer Craftsman Category Trimmer

Documents that we receive from a manufacturer of a Craftsman 316.79614 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 316.79614 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 316.79614
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 316.79614.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 316.79614, service manual, brief instructions and user manuals Craftsman 316.79614. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 316.79614.

Similar manuals

A complete manual for the device Craftsman 316.79614, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 316.79614 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 316.79614.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 316.79614 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 316.79614, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 316.79614, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 316.79614 - which should help us in our first steps of using Craftsman 316.79614
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 316.79614
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 316.79614 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 316.79614?

Use the form below

If you did not solve your problem by using a manual Craftsman 316.79614, ask a question using the form below. If a user had a similar problem with Craftsman 316.79614 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)