English dropdown-ico

Manual Toa DA-250F CU

20 pages 0.43 mb
Download

Go to site of 20

Summary
  • Toa DA-250F CU - page 1

    OPERA TING INSTRUCTIONS MUL TICHANNEL POWER AMPLIFIERS DA-250F CU DA-250FH CU Thank you for purchasing TOA's Multichannel Power Amplifier. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment. Note: The figure shows the DA-250F. ...

  • Toa DA-250F CU - page 2

    2 T ABLE OF CONTENTS 1. IMPORT ANT SAFETY INSTRUCTIONS .................................................... 3 2. SAFETY PRECAUTIONS ............................................................................... 4 3. GENERAL DESCRIPTION ............................................................................. 6 4. FEA TURES .................... ...

  • Toa DA-250F CU - page 3

    3 1. IMPORT ANT SAFETY INSTRUCTIONS • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. • Do not install near ...

  • Toa DA-250F CU - page 4

    4 When Installing the Unit • Do not expose the unit to rain or an environment where it may be splashed by water or other liquids, as doing so may result in fire or electric shock. • Use the unit only with the voltage specified on the unit. Using a voltage higher than that which is specified may result in fire or electric shock. • Do not cut, ...

  • Toa DA-250F CU - page 5

    5 shock. • When moving the unit, be sure to remove its power supply cord from the wall outlet. Moving the unit with the power cord connected to the outlet may cause damage to the power cord, resulting in fire or electric shock. When removing the power cord, be sure to hold its plug to pull. • Do not block the ventilation panels on the front. Do ...

  • Toa DA-250F CU - page 6

    6 3. GENERAL DESCRIPTION TOA's DA-250F and DA-250FH Multichannel Power Amplifiers feature high power handling capabilities and durability. The DA-250F is configured with 250 W x 4 channels (4 Ω output) and 170 W x 4 channels (8 Ω output), and the DA-250FH features a 250 W x 4 channels (19.6 Ω output) configuration. Besides, each model&ap ...

  • Toa DA-250F CU - page 7

    7 6. INST ALLA TION PRECAUTIONS • The supplied power supply cord is designed for exclusive use with this unit. Never use it with other equipment. • When mounting the unit in an equipment rack, the inside of the rack must be sufficiently ventilated. To achieve sufficient ventilation, remove all panels on the rear of the rack. • When mounting t ...

  • Toa DA-250F CU - page 8

    8 7. NOMENCLA TURE AND FUNCTIONS [Front] 1. Power switch [ ON/ OFF] Power is switched on and off with each depression of this switch. 2. Power indicator [POWER] Lights blue when the power is switched on. 3. Input volume controls [CH 1 (BRIDGE 1), CH 2, CH 3 (BRIDGE 2), CH 4] Adjust the input volume of each channel. When a bridge connection is made ...

  • Toa DA-250F CU - page 9

    9 [Rear] 6 7 8 Note: The figure is common to DA-250F and DA-250FH. 9 9 10 11 6. AC inlet Connect the supplied power cord to this inlet. 7. Functional ground terminal [SIGNAL GND] Hum noise may be generated when external equipment is connected to the unit. Connecting this terminal to the functional ground terminal of the external equipment may reduc ...

  • Toa DA-250F CU - page 10

    10 8. CONNECTIONS 8.1. Procedure Step 1. Switch off the unit's power. Step 2. Set the BRIDGE ON/OFF buttons and CH 1 mode ON/OFF button. Step 3. Connect the sound source equipment to the Input terminals. Note Refer to p. 12 for the removable terminal plug connection. Step 4. Connect speakers to the Speaker output terminals. 4-1. Unscrew the ou ...

  • Toa DA-250F CU - page 11

    11 [1 input - 2 outputs] CH1 CH1 CH2 CH3 CH4 BRIDGE 1 BRIDGE 2 - + - + – + – + Button BRIDGE 1 BRIDGE 2 CH 1 mode ON ON ON Setting Speaker output terminals 8 – 16 Ω 8 – 16 Ω 39.2 Ω 39.2 Ω DA-250F DA-250FH CH1 - + CH2 - + [3 inputs - 3 outputs (1)] CH1 CH2 CH3 CH1 CH2 CH3 CH4 Speaker output terminals 4 – 8 Ω 4 – 8 Ω 8 – 16 ...

  • Toa DA-250F CU - page 12

    12 Connector connections Step 1. Loosen the terminal screw, then insert the cable. Step 2. Retighten the terminal screw. (Pull on the cable to ensure it is securely connected.) Tip Recommended slotted screwdriver type: Screwdriver with blade that is 3 mm in width Tightens Loosens Terminal screw Slotted screwdriver Shielded cable Removable terminal ...

  • Toa DA-250F CU - page 13

    13 10. INPUT SENSITIVITY AND HIGH-P ASS FIL TER ON/OFF SETTINGS The Input sensitivity can be set to +4 dB (factory-preset) or -10 dB for each channel. Besides, only the DA-250FH employs the High-pass filter on each channel, which can be set to "ON" or "OFF." These servicing instructions are for use by qualified personnel only. T ...

  • Toa DA-250F CU - page 14

    14 1 1. PROTECTION OPERA TION LIST Failure Protection Operation Indicator Remedy Recovery Overcurrent due to overload Current limiter activated when impedance drops below the specified value. Peak indicator lights. Remove overload. Connecting a correct load automatically restores normal operation. Short circuit Current limiter activated. Load is di ...

  • Toa DA-250F CU - page 15

    15 13. CLEANING THE FIL TER Step 1. Switch off the unit's power. Step 2. Remove the ventilation panel as shown in the figure. Step 3. Detach the filter inside the ventilation panel. Step 4. Clear the filter of dust. Step 5. Replace the filter and ventilation panel. Detach the panel by pressing on the left and right sides. Filter V entilation P ...

  • Toa DA-250F CU - page 16

    16 H C CH 1 INPUT E H C CH 2 INPUT E Current Limitter Short Detector Protection Circuit OUTPUT 1 relay CH 1 OUTPUT CH 2 OUTPUT +4 dB - 10 dB CH 1 sensitivity selection jumper (+4 dB/ - 10 dB) CH 1 volume control +4 dB - 10 dB CH 2 sensitivity selection jumper (+4 dB/ - 10 dB) CH 2 volume control ON OFF BRIDGE 1 ON/OFF switch + - BRIDGE 1 OUTPUT Cur ...

  • Toa DA-250F CU - page 17

    17 14.2. DA-250FH OFF ON CH 2 HPF ON/OFF jumper HPF 50 Hz OFF ON CH 3 HPF ON/OFF jumper HPF 50 Hz OFF ON CH 4 HPF ON/OFF jumper HPF 50 Hz H C CH 1 INPUT E H C CH 2 INPUT E Current Limitter Short Detector Protection Circuit OUTPUT 1 relay CH 1 OUTPUT CH 2 OUTPUT +4 dB - 10 dB CH 1 sensitivity selection jumper (+4 dB/ - 10 dB) CH 1 volume control +4 ...

  • Toa DA-250F CU - page 18

    18 15. DIMENSIONAL DIAGRAM Unit: mm 482 465 400 374 20 31.8 44 ...

  • Toa DA-250F CU - page 19

    19 16. SPECIFICA TIONS * 0 dB = 0.775 Vrms Note: The design and specifications are subject to change without notice for improvement. • Accessories Power cord (2 m) ................................................................. 1 Removable terminal plug (3P) ............................................. 4 Volume control cap .................... ...

  • Toa DA-250F CU - page 20

    Printed in Japan 133-22-027-00 ...

Manufacturer Toa Category Stereo Amplifier

Documents that we receive from a manufacturer of a Toa DA-250F CU can be divided into several groups. They are, among others:
- Toa technical drawings
- DA-250F CU manuals
- Toa product data sheets
- information booklets
- or energy labels Toa DA-250F CU
All of them are important, but the most important information from the point of view of use of the device are in the user manual Toa DA-250F CU.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Toa DA-250F CU, service manual, brief instructions and user manuals Toa DA-250F CU. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Toa DA-250F CU.

Similar manuals

A complete manual for the device Toa DA-250F CU, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Toa DA-250F CU by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Toa DA-250F CU.

A complete Toa manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Toa DA-250F CU - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Toa DA-250F CU, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Toa DA-250F CU, that we can find in the current document
3. Tips how to use the basic functions of the device Toa DA-250F CU - which should help us in our first steps of using Toa DA-250F CU
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Toa DA-250F CU
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Toa DA-250F CU in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Toa DA-250F CU?

Use the form below

If you did not solve your problem by using a manual Toa DA-250F CU, ask a question using the form below. If a user had a similar problem with Toa DA-250F CU it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)