-
Chicago Electric 91995 - page 1
10” COMPOUND MITER SA W Model 91995 SET UP AND OPERA TING INSTRUCTIONS Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our web ...
-
Chicago Electric 91995 - page 2
Page 2 SKU 91995 For technical questions, please call 1-800-444-3353. SPECIFICA TIONS Electrical Requirements 120 V / 60 Hz / 1800 Input W atts. 15.0 AMPs Star t Up / 5300 RPM No Load. Three Prong, Grounded, P ower Cord Plug. P ower Switch T ype: Squeeze T ype. Saw Blade (Included) Diameter/T ype 10” Diameter / 60 T eeth. 7,000 Maximum RPM. Arbor ...
-
Chicago Electric 91995 - page 3
Page 3 SKU 91995 For technical questions, please call 1-800-444-3353. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY Grounded tools must be plugged int ...
-
Chicago Electric 91995 - page 4
Page 4 SKU 91995 For technical questions, please call 1-800-444-3353. A void accidental starting. Be sure the Power Switch is off before plugging in. Carrying power tools with your nger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. Remove adjusting keys or wrenches before turning the power tool on. ...
-
Chicago Electric 91995 - page 5
Page 5 SKU 91995 For technical questions, please call 1-800-444-3353. SER VICE T ool service must be performed only by qualied repair personnel. Service or maintenance performed by unqualied personnel could result in a risk of injury . When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maint ...
-
Chicago Electric 91995 - page 6
Page 6 SKU 91995 For technical questions, please call 1-800-444-3353. Before using the Miter Saw , make sure the Saw Blade is properly mounted on the Saw Spindle. Make sure the Saw Blade is balanced, and is not cracked or bent. The Saw Blade will become hot while cutting. Allow the Saw Blade to completely cool before touching. Make sure the workpie ...
-
Chicago Electric 91995 - page 7
Page 7 SKU 91995 For technical questions, please call 1-800-444-3353. The Cross Pin (28) should always be in the “locked down” position when the Saw is not being used and when the Saw is being transported. The Cross Pin should be activated in the “locked up” position when changing Saw Blades. NEVER use the Cross Pin in any cutting operation ...
-
Chicago Electric 91995 - page 8
Page 8 SKU 91995 For technical questions, please call 1-800-444-3353. Maintain this product with care. Keep the Miter Saw clean and dry for better and safer performance. For your safety , service and maintenance should be performed regularly by a qualied technician. Use the right tool or attachment for the right job. Do not attempt to force a sm ...
-
Chicago Electric 91995 - page 9
Page 9 SKU 91995 For technical questions, please call 1-800-444-3353. GROUNDING Improperly connecting the grounding wire can result in electric shock. Check with a qualied electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from ...
-
Chicago Electric 91995 - page 10
Page 10 SKU 91995 For technical questions, please call 1-800-444-3353. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See T able A.) When using more than one extension cord to make up the total length, make sure each cord contains at leas ...
-
Chicago Electric 91995 - page 11
Page 1 1 SKU 91995 For technical questions, please call 1-800-444-3353. ASSEMBL Y AND OPERA TING INSTRUCTIONS Note: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 24. T o Replace And Install A Saw Blade: W ARNING! Prior to performing any assembly and/or adjustment procedures, make sure th ...
-
Chicago Electric 91995 - page 12
Page 12 SKU 91995 For technical questions, please call 1-800-444-3353. CAUTION! The Cross Pin (28) should always be activated in the “locked down” position when the Saw is not being used and when the Saw is being transported. The Cross Pin should be activated in the “locked up” position only when changing Saw Blades. NEVER use the Cross Pin ...
-
Chicago Electric 91995 - page 13
Page 13 SKU 91995 For technical questions, please call 1-800-444-3353. 8. Depress the Spindle Lock (84) to keep the Saw Blade (56) from turning. (See Figure H.) 6. Loosen the Screw (48) that holds the Large Cover (47) in place. Then, use the Wrench (1 10) to remove the Bolt (50). (See Figure G.) 7. Rotate the Large Cover (47) and Safety Cover (53) ...
-
Chicago Electric 91995 - page 14
Page 14 SKU 91995 For technical questions, please call 1-800-444-3353. 9. Use the Wrench (109) to unscrew and remove the Spindle Bolt (58). NOTE: The Spindle Bolt unscrews in a clockwise direction. Then, remove the Outer Flange (57). (See Figure I.) 1 1. Wearing heavy duty work gloves to avoid accidental cuts, remove the old Saw Blade (56). (See Fi ...
-
Chicago Electric 91995 - page 15
Page 15 SKU 91995 For technical questions, please call 1-800-444-3353. 1. A workpiece Clamp Assembly (36) can be installed by inserting the Assembly into the hole located in the Guide Fence (37). Once inserted, lock the Assembly in place with the Thumb Screw (35). T o clamp the workpiece to the Base (8) of the Miter Saw , turn the Adjusting Knob on ...
-
Chicago Electric 91995 - page 16
Page 16 SKU 91995 For technical questions, please call 1-800-444-3353. cannot be seen clearly , disconnect the electrical Power Cord from its electrical outlet and clean the Safety Cover with a soft, damp, cloth. A mild detergent may be used, but do not use solvents which may damage the Safety Cover . (See Figure L.) The Power Switch: 1. Before plu ...
-
Chicago Electric 91995 - page 17
Page 17 SKU 91995 For technical questions, please call 1-800-444-3353. T o Adjust The Cutting Depth: 1. W ARNING! Prior to performing this procedure, make sure the Power Cord (102) of the Miter Saw is unplugged from its electrical outlet. The Dust Bag: 1. The Dust Bag (93) catches and holds the wood chips and saw dust when the Miter Saw is in opera ...
-
Chicago Electric 91995 - page 18
Page 18 SKU 91995 For technical questions, please call 1-800-444-3353. HANDLE (1) 6. If the Saw Blade (56) touches the T able (18) or any other part of the Saw Base (8), tighten the Screw (92) to raise the Saw Blade slightly until it clears. (See Figure O.) T o Adjust The Miter Angle: 1. W ARNING! Prior to performing this procedure, make sure the P ...
-
Chicago Electric 91995 - page 19
Page 19 SKU 91995 For technical questions, please call 1-800-444-3353. o 2. The bevel angle (or Saw Blade tilt capacity) may be adjusted from 0 - 45 to the left. T o do so, loosen the Handle (30) located at the rear of the Miter Saw . (See Figure P .) 3. T ilt the Back Rack (25) until the desired bevel angle of cut is achieved as indi- cated on the ...
-
Chicago Electric 91995 - page 20
Page 20 SKU 91995 For technical questions, please call 1-800-444-3353. 6. Plug the Power Cord (102) into the nearest 120 volt, grounded, electrical outlet. 7. Squeeze the Power Switch (98) to turn on the Miter Saw . 8. When the Saw Blade (56) is turning at full speed, slowly bring down the Motor Housing (75) to complete the cut. NOTE: Feed the Saw ...
-
Chicago Electric 91995 - page 21
Page 21 SKU 91995 For technical questions, please call 1-800-444-3353. 3. Daily: With a soft brush, cloth, or vacuum, remove all dust and debris from the Miter Saw . Then, use a premium quality , lightweight machine oil to lubricate all moving parts except the Saw Blade (56). 4. T o replace the Motor Carbon Brushes: It may become necessary at some- ...
-
Chicago Electric 91995 - page 22
Page 22 SKU 91995 For technical questions, please call 1-800-444-3353. P ARTS LIST NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. Part # Description Part # Description 1 Handle 56 Sa w Blade 2 Screw 57 Outer Flange 3 Spring Gasket 58 Spindle Bolt 4 Angle Lock 59 Inner ...
-
Chicago Electric 91995 - page 23
Page 23 SKU 91995 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. 1 10: WRENCH NOT SHOWN. ...
Do you have a question concerning Chicago Electric 91995?
Use the form below
If you did not solve your problem by using a manual Chicago Electric 91995, ask a question using the form below. If a user had a similar problem with Chicago Electric 91995 it is likely that he will want to share the way to solve it.