-
Moxa AWK-3131-EU - page 1
20 11 Moxa Inc . A ll rights re served. P/N: 1802031310010 AWK- 3131 Hardware Installation Guide Moxa AirWorks First Edition, February 2011 ...
-
Moxa AWK-3131-EU - page 2
- 2 - Overview Moxa's new AWK - 3131 3 - in - 1 industri al wi reless AP /bridg e/clie nt meets the growing need for faster data transmission speeds and w ider coverage by supporting IEEE 80 2.11n technology with a net data rat e of up t o 300 Mbps. The A WK - 3131 combines two adjacent 20 MHz channels into a single 40 MHz channe l to deliver ...
-
Moxa AWK-3131-EU - page 3
- 3 - • SFP - 1GLHXLC: Small form factor pluggable transceiver w ith 1000BaseLHX , LC, 40 km, 0 to 60°C • SFP - 1GLHXLC - T: Small form factor pluggabl e trans ceiver with 1000BaseLHX , LC, 40 km, - 40 to 85°C • SFP - 1GZXLC: Small form factor pluggable transceiver with 1000BaseZX , LC, 80 km, 0 to 60°C • SFP - 1GZXLC - T: Small form fac ...
-
Moxa AWK-3131-EU - page 4
- 4 - ATTENTION For security reasons, we strongly recommend ch anging the password. To do so, select Maintenance Password , and then follow the on - screen instructions. Step 5: Se lect the operation m ode for th e AWK - 31 31 By default, the AWK - 31 3 1’s operation mode is set to AP. You can change the setting in Wireless Settings Basic ...
-
Moxa AWK-3131-EU - page 5
- 5 - Panel Layout of the AWK - 3131 1. Grounding screw 2. Terminal block for PWR1,PWR2, relay, DI1, and DI2 3. Reset button 4. System LEDs: PWR1, PWR2, PoE, FAULT, and STATE LED s 5. LEDs for signal strength 6. WLAN LED 7. Ethernet or Fiber LED 8. RS - 232 console port 9. LANs: 10/100/1000 BaseT(X) RJ45 Port or 1000Base SFP 10. Main Antenna A 11. ...
-
Moxa AWK-3131-EU - page 6
- 6 - Mounting Dimensions (unit = mm) DIN - Rail Mounting The aluminum DIN - Rail attachmen t plate should be fixed to the back panel of the AWK - 3131 when you take it out of the box. If you n eed to reattach the DIN - Rail attachment plate to the AWK - 3131 , make sure the stiff metal spring is situated towards the to p, as shown in the f igures ...
-
Moxa AWK-3131-EU - page 7
- 7 - Wall Mounting (optional) For transportation app lications that require a n EN 50155 certification report, we strongly r ecommend the purchase of the optional AWK- 3131 wallmount kit, whic h has passed E N 50155 testing. Th is wallmount kit is also convenient for other a pplications that requ ire mounting the AWK- 3131 to a wall. STEP 1: Remov ...
-
Moxa AWK-3131-EU - page 8
- 8 - WARNING • This equipment is intended to be used in a Restrict ed Access Location, such as a ded icated computer room . A ccess can only be gained by SERVICE PERSONS or by USERS who ha ve been instructed about the fact tha t the metal chassis of the equi pment i s extremely hot and m a y cause burns. • S ervice persons or users have to pay ...
-
Moxa AWK-3131-EU - page 9
- 9 - ATTENTION This product is inte nded to be supplied by a Listed Power Unit marked “ Class 2 ” or “ LPS ” and rated O/P: 12 to 48 V DC , minim um 6 W (12 V to 48V), 25°C . ATTENTION Make sure the e xt ern al p ower a da pt o r (includes power cord s and plug a ssembli es) prov ided w ith the un it is cert ifie d an d suit abl e for use ...
-
Moxa AWK-3131-EU - page 10
- 10 - ATTENTION Before connecting the AWK - 3131 to the DC power inputs, mak e sure the DC power source vo ltage is stable. Wiring the Relay Contact The AWK - 3131 has one relay output, wh ich consists of the t wo contacts of the terminal block on the AWK - 3131 ’s top pane l. Refer to the previous section for detailed instruct ions on how to co ...
-
Moxa AWK-3131-EU - page 11
- 11 - Communication Con nections 10/100BaseT(X) Ethern et Port Connection The 10/100BaseT(X) ports located on the AWK- 31 31 ’s front panel are used to connect to Ethernet- enabled devices. Below we show pinouts for both MDI (NIC - type) po rts and MDI -X (HUB/Switch - type) ports. MDI Port Pinouts MDI - X Port Pinouts 8-pin RJ45 Pin Signal Pin ...
-
Moxa AWK-3131-EU - page 12
- 12 - NOTE 1. The pin numbers for ma le DB9 and DB25 conne ctors, and hole numbers for fema le DB9 and DB25 con nectors are labeled on the connecto r. However, the number s are typically quite small, so y ou may need to us e a magnifying glass to see the numbers clearl y. 2. The pi n numbers for both 8 - pin and 10 - pin RJ45 connectors (and ports ...
-
Moxa AWK-3131-EU - page 13
- 13 - LAN Green/ Amber Amber LAN port’s 10/ 100 Mbps link is active. Amber Blink ing Data is being transmitted at 10/100 Mbps Amber Off LAN port’s 10/ 100 Mbps link is inactive Green LAN port’s 1000 Mbps link is active. Green Blink ing Data is being transmitted at 100 0 Mbps Green Off LAN port’s 1000 Mbps link is inactive Specifications WL ...
-
Moxa AWK-3131-EU - page 14
- 14 - TX Transmit Power: 802.11b: 1 to 11 Mbps: Typ. 18 dBm (± 1.5 dBm) 802.11g: 6 to 24 Mbps: Typ. 18 dBm (± 1.5 dBm) 36 to 48 Mbps: Typ. 17 dBm (± 1.5 dBm) 54 Mbps: Typ. 1 5 dBm (± 1.5 dB m) 802.11a: 6 to 24 Mbps: Typ. 17 dBm (± 1.5 dBm) 36 to 48 Mbps: Typ. 16 dBm (± 1.5 dBm) 54 Mbps: Typ. 1 4 dBm (± 1.5 dB m) TX Transmit Power MIMO: 802. ...
-
Moxa AWK-3131-EU - page 15
- 15 - Alarm Contact: 1 relay output w ith current carry ing capacity of 1 A @ 24 VDC Digital Inputs: 2 electrically isolated inputs • +13 to +30 V for state “1” • +3 to - 30 V for state “0” • Max. input current: 8 mA Physical Characteristics Housing: Metal, IP30 protection Weight: 970 g Dimensions: 53.6 x 135 x 105 m m (2.11 x 5.31 x ...
-
Moxa AWK-3131-EU - page 16
- 1 6 - ATTENTION Use the antennas corr ectly: The 2.4 GHz ante nnas are needed when the AWK - 3131 operates in IEEE 802.11b/ g/ n . The 5 GHz antennas are needed fo r IEEE802.11a /n . Make sure your ante nna installation is within a safety area, which is covered by a lightning protection or surge arr est system. Technical Support Contact Inform at ...
Do you have a question concerning Moxa AWK-3131-EU?
Use the form below
If you did not solve your problem by using a manual Moxa AWK-3131-EU, ask a question using the form below. If a user had a similar problem with Moxa AWK-3131-EU it is likely that he will want to share the way to solve it.