English dropdown-ico

Manual Fairchild RC5040

24 pages 0.5 mb
Download

Go to site of 24

Summary
  • Fairchild RC5040 - page 1

    Application Note 42 Implementing the RC5040 and RC5042 DC-DC Conver ters on Pentium ® Pr o Motherboar ds www .fair childsemi.com Intr oduction This document describes how to implement a switching v olt- age regulator using an RC5040 or an RC5042 high speed controller , a po wer inductor , a Schottky diode, appropriate capacitors, and external po w ...

  • Fairchild RC5040 - page 2

    AN42 APPLICATION NOTE 2 T able 2. Intel P entium Pro and OverDrive Processor P ower Specifications Notes: 1. Maximum power values are measured at typical V CC P to take into account the thermal time constant of the CPU package. 2. Flexible motherboard specifications are recommendations only. Actual specifications are subject to change. CPU Model & ...

  • Fairchild RC5040 - page 3

    APPLICATION NOTE AN42 3 RC5040 and RC5042 Description Simple Step-Down Con ver ter Figure 1. Simple Buck DC-DC Converter Figure 1 illustrates a step-down DC-DC con verter with no feedback control. The basic step-do wn conv erter serves as the basis for deriving the design equations for the RC5040 and RC5042. From Figure 1, the basic operation begin ...

  • Fairchild RC5040 - page 4

    AN42 APPLICATION NOTE 4 High Current Output Drivers The RC5040 contains two identical high current output driv ers that use high speed bipolar transistors in a push-pull confi guration. Each driv er is capable of delivering 1A of cur - rent in less than 100ns. Each driv er’ s power and ground are separated from the chip power and ground for addi ...

  • Fairchild RC5040 - page 5

    APPLICATION NOTE AN42 5 Over-V oltage Protection The RC5040 and RC5042 constantly monitor the output voltage for protection against o ver voltage. If the v oltage at the VFB pin exceeds 20% of the selected program voltage, an ov er-v oltage condition is assumed, and the controller dis- ables the output driv e signal to the external MOSFET(s). Short ...

  • Fairchild RC5040 - page 6

    AN42 APPLICATION NOTE 6 Figure 4. Synchronous DC-DC Converter Application Schematic Using RC5040 Figure 5. Non-Synchronous DC-DC Converter Application Schematic Using RC5042 VO GND VID3 VID2 VID1 VID0 8 7 6 5 4 3 2 1 9 10 11 12 13 14 15 16 17 18 19 20 VCC PWRGD RC5040 VCC VCC OUTEN R5 10K C10 0.1 µ F C11 0.22 µ F R6 10K R4 10K 10K 10K 10K R3 R2 R ...

  • Fairchild RC5040 - page 7

    APPLICATION NOTE AN42 7 MOSFET Selection This application requires the use of N-channel, Logic Lev el Enhancement Mode Field Effect Transistors. The desired characteristics of these components are: • Low Static Drain-Source On-Resistance R DS,ON < 37 m Ω (lo wer is better) • Low g ate driv e voltage, V GS ≤ 4.5V • Power package with lo ...

  • Fairchild RC5040 - page 8

    AN42 APPLICATION NOTE 8 MOSFET Gate Bias The MOSFET(s) can be biased using one of two methods: Charge Pump or 12V Gate Bias. Charge Pump (or Bootstrap) Figure 6 employs a char ge pump to provide the MOSFET gate bias. The char ge pump capacitor, CP , is used as a flying capacitor to boost the voltage of the RC5040 or RC5042 out- put driv er . When ...

  • Fairchild RC5040 - page 9

    APPLICATION NOTE AN42 9 Con ver ter Efficiency Losses due to parasitic resistance in the switches, inductor , and sense resistor dominate at high load-current lev els. The major loss mechanisms under heavy loads, in order of importance, are: • MOSFET I 2 R Losses • Inductor Losses • Sense Resistor Losses • Gate-Charge Losses • Diode-Cond ...

  • Fairchild RC5040 - page 10

    AN42 APPLICATION NOTE 10 Selecting the Inductor Selecting the right inductor component is critical in the DC-DC con verter application. The inductor’ s critical param- eters to consider are inductance (L), maximum DC current (I O ), and coil resistance (R l ). The inductor core material is crucial in determining the amount of current it can withs ...

  • Fairchild RC5040 - page 11

    APPLICATION NOTE AN42 11 where: • V IN = Input V oltage to the Con verter • V SW = V oltage Across the MOSFET = I LOAD x R DS,ON • V D = Forw ard V oltage of the Schottky Diode • T = The Switching Period of the Con verter = 1/f S , Where f S = Switching Frequency . For an input v oltage of 5V , an output voltage of 3.3V , an inductor value ...

  • Fairchild RC5040 - page 12

    AN42 APPLICATION NOTE 12 T able 8. R sense for v arious load currents Discrete Sense Resistor Discrete iron alloy resistors come in a v ariety of tolerances and power ratings, and are ideal for precision implementa- tions. Either an MnCu alloy wire resistor or an CuNi alloy wire resistor is ideal for a low cost implementation. Embedded Sense Resist ...

  • Fairchild RC5040 - page 13

    APPLICATION NOTE AN42 13 currents to change. Therefore, combining an embedded resistor with a discrete resistor may be a desirable option. This section discusses a design that provides fle xibility and addresses wide tolerances. Refer to Figure 12. In this design, the user has the option to choose either an embedded or a discrete MnCu sense resist ...

  • Fairchild RC5040 - page 14

    AN42 APPLICATION NOTE 14 Figure 14A. V CCQP Output Waveform for Normal Operation Condition with V out = 3.3V@10A Figure 14B. V CCQP Output Waveform for Output Shorted to Ground The Schottky diode has a po wer dissipation consideration during the short circuit condition. During normal operation, the diode dissipates power when the po wer MOSFET is o ...

  • Fairchild RC5040 - page 15

    APPLICATION NOTE AN42 15 T able 10. Schottky Diode Selection T able Output Filter Capacitors Output ripple performance and transient response are functions of the filter capacitors. Since the 5V supply of a PC motherboard may be located sev eral inches away from the DC-DC con verter , the input capacitance can play an impor- tant role in the load ...

  • Fairchild RC5040 - page 16

    AN42 APPLICATION NOTE 16 Refer to Appendix A for Directory of component suppliers. Notes : 1. In synchronous mode using the RC5040, a 1A schottky diode (1N5817) may be substituted for the MBR1545CT. 2. MOSFET M3 is only required for the RC5040 synchronous application. C13, C14, C15 Sanyo 6MV1500GX 1500 µ F 6.3V electrolytic capacitor 10mm x 20mm E ...

  • Fairchild RC5040 - page 17

    APPLICATION NOTE AN42 17 PC Motherboard La yout and Gerber File A reference design for motherboard implementation of the RC5040 and RC5042 along with the Layout Gerber File and Silk Screen are presented below . The actual PCAD Gerber File can be obtained from Raytheon Electronics Semicon- ductor Division’ s Marketing Department at (415) 966-7819. ...

  • Fairchild RC5040 - page 18

    AN42 APPLICATION NOTE 18 ...

  • Fairchild RC5040 - page 19

    APPLICATION NOTE AN42 19 Guidelines f or Debug ging and P erformance Ev aluations Debug ging Y our First Design Implementation Use the following procedure to help you deb ug your design implementation: 1. Note the VID pins settings. The y tell you what voltage is to be expected. 2. Do not connect any load to the circuit. While monitoring the output ...

  • Fairchild RC5040 - page 20

    AN42 APPLICATION NOTE 20 4. Premature shut down can be caused by an inappropriate value of sense resistor . See the Sense Resistor section. 5. A poor load regulation can hav e many causes. Y ou should first check the voltages and signals at the critical pins. 6. The VREF pin should be at the v oltage set by the VID pins. If the power supply pins a ...

  • Fairchild RC5040 - page 21

    APPLICATION NOTE AN42 21 Note: Load regulation is expected to be typically around 0.8%. The load regulation performance for this device under evaluation is excellent. Output V oltag e Load T ransients Due to Load Current Step This test is performed using Intel P6.0/P6S/P6T V oltage T ransient T ester . Note: Excellent transient voltage response. Tr ...

  • Fairchild RC5040 - page 22

    AN42 APPLICATION NOTE 22 Component Case T emperature Note: Case temperatures are all within guidelines. Our guideline is that case temperatures for all components should be below 105 ° C @25 ° C Ambient. Comments: Excellent input ripple voltage. Input ripple voltage is recommended to be less than 5% of the output voltage. Device Description Case ...

  • Fairchild RC5040 - page 23

    APPLICATION NOTE AN42 23 Attachment C Attachment D Attachment E Attachment F Attachment G Summary This application note cov ers for implementation of a DC-DC con verter on a Pentium Pro motherboard using the RC5040 and RC5042. The detailed discussion includes Pentium Pro processor power requirements, RC5040 and RC5042 description, design considerat ...

  • Fairchild RC5040 - page 24

    AN42 APPLICATION NOTE 2/98 0.0m Stock#AN30000042  1998 Fairchild Semiconductor Corporation LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support de ...

Manufacturer Fairchild Category Computer Hardware

Documents that we receive from a manufacturer of a Fairchild RC5040 can be divided into several groups. They are, among others:
- Fairchild technical drawings
- RC5040 manuals
- Fairchild product data sheets
- information booklets
- or energy labels Fairchild RC5040
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fairchild RC5040.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fairchild RC5040, service manual, brief instructions and user manuals Fairchild RC5040. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fairchild RC5040.

Similar manuals

A complete manual for the device Fairchild RC5040, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fairchild RC5040 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fairchild RC5040.

A complete Fairchild manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fairchild RC5040 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fairchild RC5040, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fairchild RC5040, that we can find in the current document
3. Tips how to use the basic functions of the device Fairchild RC5040 - which should help us in our first steps of using Fairchild RC5040
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fairchild RC5040
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fairchild RC5040 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fairchild RC5040?

Use the form below

If you did not solve your problem by using a manual Fairchild RC5040, ask a question using the form below. If a user had a similar problem with Fairchild RC5040 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)