-
Patton electronic 2085 - page 1
USER MANUAL SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M2085-D Doc# 047033U, Rev . E Revised 1/22/08 MODEL 2085 High Speed RS-232 to RS-485 Interface Converter CERTIFIED An ISO-9001 Certified Company Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your ...
-
Patton electronic 2085 - page 2
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 2085 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized ...
-
Patton electronic 2085 - page 3
1.3 SERVICE All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container . This number may be obtained from Patton Electronics T echnical Service: (301) 975-1007, http://www .patton.com ; support@patton ...
-
Patton electronic 2085 - page 4
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor . If any questions or problems arise during installation or use of this product, please do not hesitate to contact Patton Electronics T echnical Support at (301 ...
-
Patton electronic 2085 - page 5
3.0 CONFIGURA TION The Model 2085 is configured using an eight position DIP switch and a DCE/DTE switch. Figure 1 (below) shows the location of the DCE/DTE switch (externally accessible) on the PC board, as well as the power supply daughter board and terminal block. Figure 2 (below) shows the location of the eight position DIP switch on the undersi ...
-
Patton electronic 2085 - page 6
3.1 SETTING THE DCE/DTE SWITCH For your convenience, the Model 2085 has an externally accessible DCE/DTE switch. If the device connected to the Model 2085 is a modem or multiplexer (or is wired like one), set the switch to “DTE”. This setting causes the Model 2085 to behave like Data T erminal Equipment and transmit data on pin 2. If the device ...
-
Patton electronic 2085 - page 7
4.1.3 4-WIRE CONNECTION USING TERMINAL BLOCKS If your RS-485 application requires you to connect two pairs of bare wires to the Model 2085, you will need to open the case to access the terminal blocks. The following instructions will tell you how to open the case, connect the bare wires to the terminal blocks, and fasten the strain relief collar in ...
-
Patton electronic 2085 - page 8
S1-4: Echo Mode The setting for switch S1-4 determines whether the Model 2085 echoes data back to the transmitting device (half-duplex mode only). S1-4 Setting On Echo On Off Echo Off S1-5: Carrier Control Method The setting for switch S1-5 determines whether the carrier is “Constantly On” or “Controlled by RTS”. This setting allows for ope ...
-
Patton electronic 2085 - page 9
3.4 CONFIGURA TION SWITCH APPLICA TIONS The switch settings generally needed to configure the Model 2085 for various applications are shown in the table below . Note: Do not change switch settings until you have carefully read Section 3.3. 8 S1-1: “Xmt Off” Imp. OFF OFF OFF OFF OFF S1-2: “Xmt Off” Imp. OFF OFF OFF OFF OFF S1-3: RTS/CTS Dela ...
-
Patton electronic 2085 - page 10
3.4 CONFIGURA TION SWITCH APPLICA TIONS The switch settings generally needed to configure the Model 2085 for various applications are shown in the table below . Note: Do not change switch settings until you have carefully read Section 3.3. 8 S1-1: “Xmt Off” Imp. OFF OFF OFF OFF OFF S1-2: “Xmt Off” Imp. OFF OFF OFF OFF OFF S1-3: RTS/CTS Dela ...
-
Patton electronic 2085 - page 11
S1-4: Echo Mode The setting for switch S1-4 determines whether the Model 2085 echoes data back to the transmitting device (half-duplex mode only). S1-4 Setting On Echo On Off Echo Off S1-5: Carrier Control Method The setting for switch S1-5 determines whether the carrier is “Constantly On” or “Controlled by RTS”. This setting allows for ope ...
-
Patton electronic 2085 - page 12
4.1.3 4-WIRE CONNECTION USING TERMINAL BLOCKS If your RS-485 application requires you to connect two pairs of bare wires to the Model 2085, you will need to open the case to access the terminal blocks. The following instructions will tell you how to open the case, connect the bare wires to the terminal blocks, and fasten the strain relief collar in ...
-
Patton electronic 2085 - page 13
3.1 SETTING THE DCE/DTE SWITCH For your convenience, the Model 2085 has an externally accessible DCE/DTE switch. If the device connected to the Model 2085 is a modem or multiplexer (or is wired like one), set the switch to “DTE”. This setting causes the Model 2085 to behave like Data T erminal Equipment and transmit data on pin 2. If the device ...
-
Patton electronic 2085 - page 14
3.0 CONFIGURA TION The Model 2085 is configured using an eight position DIP switch and a DCE/DTE switch. Figure 1 (below) shows the location of the DCE/DTE switch (externally accessible) on the PC board, as well as the power supply daughter board and terminal block. Figure 2 (below) shows the location of the eight position DIP switch on the undersi ...
-
Patton electronic 2085 - page 15
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor . If any questions or problems arise during installation or use of this product, please do not hesitate to contact Patton Electronics T echnical Support at (301 ...
-
Patton electronic 2085 - page 16
1.3 SERVICE All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container . This number may be obtained from Patton Electronics T echnical Service: (301) 975-1007, http://www .patton.com ; support@patton ...
-
Patton electronic 2085 - page 17
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 2085 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized ...
-
Patton electronic 2085 - page 18
APPENDIX B P A TTON MODEL 2085 RS-232 PIN CONFIGURA TIONS Copyright © Patton Electronics Company 1- (FG) Frame Ground 2- (TD) Transmit Data T o Model 2085 3- (RD) Receive Data From Model 2085 4- (RTS) Request to Send T o Model 2085 5- (CTS) Clear to Send From Model 2085 6- (DSR) Data Set Ready From Model 2085 7- (SG) Signal Ground 8- (DCD) Data Ca ...
-
Patton electronic 2085 - page 19
APPENDIX B P A TTON MODEL 2085 RS-232 PIN CONFIGURA TIONS Copyright © Patton Electronics Company 1- (FG) Frame Ground 2- (TD) Transmit Data T o Model 2085 3- (RD) Receive Data From Model 2085 4- (RTS) Request to Send T o Model 2085 5- (CTS) Clear to Send From Model 2085 6- (DSR) Data Set Ready From Model 2085 7- (SG) Signal Ground 8- (DCD) Data Ca ...
-
Patton electronic 2085 - page 20
USER MANUAL SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M2085-D Doc# 047033UD, Rev . E Revised 1/22/08 MODEL 2085 High Speed RS-232 to RS-485 Interface Converter CERTIFIED An ISO-9001 Certified Company Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your ...
Do you have a question concerning Patton electronic 2085?
Use the form below
If you did not solve your problem by using a manual Patton electronic 2085, ask a question using the form below. If a user had a similar problem with Patton electronic 2085 it is likely that he will want to share the way to solve it.