English dropdown-ico

Manual Navico Class B Transceiver NAIS-300

24 pages 1.17 mb
Download

Go to site of 24

Summary
  • Navico Class B Transceiver NAIS-300 - page 1

    N A I S 3 0 0 MANUAL NAVICO NAIS-300 Class B Transceiver English ...

  • Navico Class B Transceiver NAIS-300 - page 2

    2 Contents The technical data, information and illustrations contained in this publication were to the best of our knowledge correct at the time of going to print. W e reserve the right to change specications, equipment, installation and maintenance instructions without notice as part of our policy of continuous development and improv ement. No ...

  • Navico Class B Transceiver NAIS-300 - page 3

    Contents 3 Contents 1 Introduction 5 1.1 Gener al overview 5 1.2 SimNet/NMEA2000 6 2 I ns t a l l at i o n 7 2.1 Gener al 7 2.2 Mounting 7 2.3 Cabling 8 2.4 SimNet/NMEA2000 cable 9 SimNet (300-N model only) 9 NMEA2000 (300-L model only) 10 2.5 NMEA0183-HS (RS232) 10 2.6 NMEA0183-HS (RS485) 10 2.7 T ransmit disable switch 10 2.8 GPS antenna 10 2.9 V ...

  • Navico Class B Transceiver NAIS-300 - page 4

    4 Contents RX 18 4.3 Enable/disable switch (Silent Mode) 18 5 Appendix 19 5.1 Maintenance 19 5.2 T roubleshooting 19 5.3 Accessories 19 5.4 Product specications 2 0 5.5 Dimensions 22 5.6 Service and warr anty 22 5.7 Declar ation of Conformity (EU) 23 ...

  • Navico Class B Transceiver NAIS-300 - page 5

    Introduction 5 1 Introduction 1.1 General overview The NAIS-300 is a Class B T ransponder that’ s purpose is to transmit the position and other information about y our vessel, to other AIS equipped v essels. It is housed in a rugged waterproof enclosure to withstand the rigors of the marine environment. Th e NA I S - 30 0 us e s a s op h i st i c ...

  • Navico Class B Transceiver NAIS-300 - page 6

    6 Introduction 1.2 SimNet/NMEA2000 SimNet is Navico’ s proprietary high speed data bus network compatible with NMEA2000. It provides intelligent sharing of data and control information between a wide range of marine electronics and instruments. ...

  • Navico Class B Transceiver NAIS-300 - page 7

    Installation 7 2 I n s t a ll a ti o n 2.1 General The NAIS-300 is designed to be mounted on a flat surface somewhere out of sight, but easily accessible. However , to determine the best possible location, you need to consider how and where, you are going to run the cabling from the sides of the unit. The NAIS-300 is very simple to install, howev e ...

  • Navico Class B Transceiver NAIS-300 - page 8

    8 Installation 2.3 Cabling Once you hav e secured your NAIS-300 to a flat surface, you will need to connect the power , SimNet/NMEA2000 and RS232 cables supplied with the unit. The RS485 cable and switch are not supplied, but would be fitted in the same manner . With reference to the connector wiring, Figure 2.1 and the assembly diagram, Figure. 2. ...

  • Navico Class B Transceiver NAIS-300 - page 9

    Installation 9 C h o o s e t h e n i p p le s di r e ct l y a b o v e t h e pa r t s o f t h e c o n n e c to r yo u w an t t o wi r e i n t o a n d c u t o f f t h e t o p s e c t i o n t o t h e re q u ir e d d i a me t e r . P as s the po we r a nd RS 232 c abl es th rou gh th e c r ad le and t hen t hro ugh t he ho le in th e r esp ec tiv e ni ...

  • Navico Class B Transceiver NAIS-300 - page 10

    10 Installation NMEA2000 (300-L model only) With the supplied cable connected to the NAIS-300, connect the other end into the supplied T -connector , then connect this into the vessels NMEA2000 network. 2.5 NMEA0183-HS ( RS232 supplied ) Th i s d at a ca b le is us e d t o c o nn e ct th e N A IS - 3 00 to a P C or la p t op in or d er to co n g ...

  • Navico Class B Transceiver NAIS-300 - page 11

    Installation 11 The cable can be routed in the molding to drop down directly underneath, or by breaking out the thin traps, the cable can be routed out of the side of the antenna. Alt er nat iv el y , th e ant enn a ma y b e fix e d o n a s tan da rd 1” thr ea ded mo un tin g pol e ( No t s up pli ed) . At ta ch the s upp lie d mou nt ing ba se t ...

  • Navico Class B Transceiver NAIS-300 - page 12

    12 Installation Th e mo s t im p o rt a n t f a ct o r i n th e pe r f or m a n ce o f a n y AI S tr an s ce i v e r w i l l b e t h e q u a li t y an d p os i t io n i ng o f t h e an t e nn a . As the range of VHF signals are go verned by line of sight, the antenna should be placed as high as possible, while remaining clear of any metallic object ...

  • Navico Class B Transceiver NAIS-300 - page 13

    Installation 13 The antenna cable should terminate in a standard marine PL259 plug fitting. Connect the antenna plug to the socket on the side of the unit and screw the retaining collar down. Figure 2.3. To avoid possible water damage to the transceiver, it is recommended that all cables are looped to provide a drip path.   ...

  • Navico Class B Transceiver NAIS-300 - page 14

    14 Installation ...

  • Navico Class B Transceiver NAIS-300 - page 15

    Configuration 15 3 Conguration 3.1 General Before the NAIS-300 can become fully functional, it will be necessary to load the following information about your vessel into the unit: V essels Name Call Sign MMSI Number V essels Dimensions V essel T ype In order to enter this information, you will need to connect your NAIS-300 to y our PC or laptop ...

  • Navico Class B Transceiver NAIS-300 - page 16

    16 Configuration For security reasons the MMSI of the vessel cannot be changed once programmed. Do not programme the MMSI unless you are certain you have the correct information. Please check the number entered carefully. If the MMSI programmed is incorrect the AIS transponder will need to be returned to the supplier for factory reset. Should it be ...

  • Navico Class B Transceiver NAIS-300 - page 17

    Operation 17 4 Operation 4.1 General The NAIS-300 has a limited user interface, consisting of a transmit enable/disable switch, (not supplied), and four indicators on the top of the unit, they are: PWR [Green] - P ower/GPS Lock Status/Silent Mode BIIT [R ed] - Built In Integrity T est TX [Y ellow] - T ransmit RX [Blue] - AIS Message R eceived 4.2 I ...

  • Navico Class B Transceiver NAIS-300 - page 18

    18 Operation 6 flashes - noise threshold exceeded 7 flashes - voltage supply fault The “ BII T” me ssa ge wi ll re mai n the re un til th e fau lt is cle ar ed by th e N AI S- 300 ci rc uit ry , or the u nit ha s bee n rep ai red . TX After the initial five seconds the LED will then go out. It will light for one second every time the unit tr an ...

  • Navico Class B Transceiver NAIS-300 - page 19

    Appendix 19 5 Appendix 5.1 Maintenance P eriodically check that the cables are secure and that the connectors have not work ed their wa y loose. 5.2 Troubleshooting These simple checks should be carried out before seeking technical assistance and may sa ve time and expense. General Symptom Possible Cause Remedy Unit will not switch on F ault y conn ...

  • Navico Class B Transceiver NAIS-300 - page 20

    20 Appendix 5.4 Product specications AIS Type Class B for use on non-SOLAS cr aft VHF Receiver R eceiver type Dual TDMA (shared DSC) Sensitivity < -107dBm for 20% PER T ransmit power 2W att T ype Approv al Meets IEC62287-1 GPS Receiver R eceiver type Integral 16 channel receiv er EMC IEC60945 Power V oltage 10.8 – 15.6VDC Current <0.5A S ...

  • Navico Class B Transceiver NAIS-300 - page 21

    Appendix 21 NMEA2000 AIS PGNs 129038 Class A P osition R eport 129039 AClass B P osition R eport 129040 Class B Extended P osition R eport 129792 DGNSS Broadcast Binary Message 129793 UT C and Date R eport 129794 Class A Static and V oyage R elated Data 129795 Addressed Binary Message 129796 Acknowledge 129797 Binary Broadcast Message 129798 SAR Ai ...

  • Navico Class B Transceiver NAIS-300 - page 22

    22 Appendix 5.5 Dimensions Figure 5.1 - NAIS-300 dimensions Figure 5.2 - GPS Antenna dimensions 5.6 Service and warranty If it is necessary to hav e a unit repaired, please contact your local authorized dealer . F or worldwide warr anty details and a list of authorised Navico agents please refer to the W arranty Card supplied with this unit. NAIS-3 ...

  • Navico Class B Transceiver NAIS-300 - page 23

    Appendix 23 English Hereby , Navico AS declares that this NAIS-300 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish Navico AS vakuuttaa täten että NAIS-300 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Dutch Hie ...

  • Navico Class B Transceiver NAIS-300 - page 24

    www.navico.com ...

Manufacturer Navico Category GPS Receiver

Documents that we receive from a manufacturer of a Navico Class B Transceiver NAIS-300 can be divided into several groups. They are, among others:
- Navico technical drawings
- Class B Transceiver NAIS-300 manuals
- Navico product data sheets
- information booklets
- or energy labels Navico Class B Transceiver NAIS-300
All of them are important, but the most important information from the point of view of use of the device are in the user manual Navico Class B Transceiver NAIS-300.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Navico Class B Transceiver NAIS-300, service manual, brief instructions and user manuals Navico Class B Transceiver NAIS-300. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Navico Class B Transceiver NAIS-300.

Similar manuals

A complete manual for the device Navico Class B Transceiver NAIS-300, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Navico Class B Transceiver NAIS-300 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Navico Class B Transceiver NAIS-300.

A complete Navico manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Navico Class B Transceiver NAIS-300 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Navico Class B Transceiver NAIS-300, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Navico Class B Transceiver NAIS-300, that we can find in the current document
3. Tips how to use the basic functions of the device Navico Class B Transceiver NAIS-300 - which should help us in our first steps of using Navico Class B Transceiver NAIS-300
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Navico Class B Transceiver NAIS-300
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Navico Class B Transceiver NAIS-300 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Navico Class B Transceiver NAIS-300?

Use the form below

If you did not solve your problem by using a manual Navico Class B Transceiver NAIS-300, ask a question using the form below. If a user had a similar problem with Navico Class B Transceiver NAIS-300 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)