English dropdown-ico

Manual Snapper 8246, 9266E, 11306, 9266

24 pages 0.35 mb
Download

Go to site of 24

Summary
  • Snapper 8246, 9266E, 11306, 9266 - page 1

    Safety Instructions & Operator’s Manual for TWO STAGE LARGE FRAM E SNOW THROWER SERIES 6 MODELS 8246 9266E 11306 MODEL NUMBER EXPLA NA TION 9 26 6 E ENGINE HP ELECT RIC ST A R T A UGER WIDT H SERIES DESIGNATION 8 – 8.0 Engine HP (En gine Horse Pow er 24 – 24” A uger Width 6 – Series Designation 9 – 9.0 Engine HP ( Engine Horse Pow e ...

  • Snapper 8246, 9266E, 11306, 9266 - page 2

    2 IMPORTA NT SA FETY INST RUC TIONS WARNING: This pow erful machin e is capable of ampu tating h ands and feet and can throw objects that can cause injury a nd d a m ag e ! Failure to comply with the follow ing instruct ions may result in se rious injury to the operator or other persons. The ow ner of the snow thrower must understand these instruct ...

  • Snapper 8246, 9266E, 11306, 9266 - page 3

    3 IMPORTA NT SA FETY INST RUC TIONS OPERA TIONA L PRECA UTIONS (Continued From Pre vious Page) 7. DO NOT put hands or feet ne ar or under rotatin g parts. Keep clear of the discharge opening at all times. 8. St art engine only where exhaust fu mes will be safely dissipated. A llow a brief warm-up pe riod, and practice operation of controls outside ...

  • Snapper 8246, 9266E, 11306, 9266 - page 4

    4 TABLE OF CONTENTS SECTION 1 - IMPORTA NT SA FETY INSTRUCTIONS .......................... 2-3 TA BLE OF CO NTENTS ............................................................................ 4 SECTION 2 - OPERA TIN G INSTRUCTIONS ....................................... 5-10 Introduc tion............................................................. ...

  • Snapper 8246, 9266E, 11306, 9266 - page 5

    5 Section 2 - OPERA TING INSTRUCTIONS 1.1 INTRODUCT ION Before s tarting m achine, vis ually check location of all operational controls and identify m ajor parts discussed in Operator’s Manual. FIGURE 1.1 NOMENCLATURE TRA CTION CLUTCH CONT ROL LEVER HIGH SPEED IMPELLER COLLECT OR AUGERS DISCHARGE DEFLECTOR CA P HEA D LIGHT (26” & 30” M OD ...

  • Snapper 8246, 9266E, 11306, 9266 - page 6

    6 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-START CHECK LIST Make the f ollowing check s and perf orm the servic e required bef ore each start- up. 2.1.1. Check engine oil and add oil as needed to bring level up to the FULL m ark . Refer to engine owner’s m anual for oil specif ications. 2.1.2. Check guards, c hutes, deflec tors and cover s to ...

  • Snapper 8246, 9266E, 11306, 9266 - page 7

    7 Section 2 - OPERA TING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.1.9. Check the AC elec trical outlet that will be used and m ake s ure it is a polar ized outlet. The ma chine has a polarized plug (one blade of plug is wider than the other) that will accept a polarized extension co rd. The ex tension cord will fit into a polarized outlet (r eceptac ...

  • Snapper 8246, 9266E, 11306, 9266 - page 8

    8 Section 2 - OPERA TING INSTRUCTIONS 2.2 ST A R TING , OPERATION & ST OPPING (RECOIL STA RT MODELS) (Go t o Page 9 for Elect ric Start M odels) (Continued From Pre vious Page) 2.2.2. PROPELLING SNOW THROWER IMPO RTANT: T his snow thrower has six forward speeds and one rever se speed. 1. Move ground s peed control to the des ired speed position ...

  • Snapper 8246, 9266E, 11306, 9266 - page 9

    9 Section 2 - OPERA TING INSTRUCTIONS 2.2 ST A R TING , OPERATION & ST OPPING (RECOIL STA RT MODELS) 2.2.6. STOPPING - ENGINE, A UGER & WHEEL DRIVE Stop the auger /im peller and wheel drive by releasing the auger/im peller and wheel drive control levers . Stop the engine by m oving the engine speed control to the s top position or rem oving ...

  • Snapper 8246, 9266E, 11306, 9266 - page 10

    10 Section 2 - OPERA TING INSTRUCTIONS 2.2 ST A R TING , OPERATION & ST OPPING (ELECTRIC STA RT M ODELS) (Go to Page 7 for Recoil Start Models) (Continue From Pre vious Page) WA RNING Objects can b e thrown b y the snow throw er wh ile it is in operation. Thrown objects could caus e ser ious injury to the operator or by standers. Alway s wear s ...

  • Snapper 8246, 9266E, 11306, 9266 - page 11

    11 Section 3 - MA INTENA NCE 3.1 INTRODUCT ION To retain the quality of the snow thrower, use only genuine SNAPPER replacem ent parts. Contac t a local SNAPPER dealer for par ts and servic e assistanc e. For the corr ect part or inform ation for a particular s now thrower, alway s mention m odel and serial num ber. 3.2 SERVICE - A FT ER FIRST 5 HOU ...

  • Snapper 8246, 9266E, 11306, 9266 - page 12

    12 Section 3 - MA INTENA NCE 3.4 ANNUA LLY (END OF EA CH SEA SON) Perfor m all m aintenanc e as descr ibed in the maintenanc e schedule. 3.4.1. Engine Refer to engine owner’s manual for service instru ctio ns. 3.4.2. Spark Plug Refer to engine owner’s manual for service instru ctio ns. 3.5 STORA GE PROCEDURE Refer to the Engine O wner’s Manua ...

  • Snapper 8246, 9266E, 11306, 9266 - page 13

    13 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt any adjustments, maintenance, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure w ire away from spark p lug. 4.1 A UGER/IMPELLER and WHEEL DRIVE BELT A D JUSTM ENT /REPLACEMEN T W hen operating m achine releas e th ...

  • Snapper 8246, 9266E, 11306, 9266 - page 14

    14 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt any adjustments, maintenance, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure w ire away from sp ark plug. Befo re tilting machine, d rain all the fuel f rom fuel tank. A llow engine to run, outdoors where fumes ...

  • Snapper 8246, 9266E, 11306, 9266 - page 15

    15 Section 4 - REPA IR & A DJUSTMENTS WA RNING DO NOT attempt any adjustments, maintenance, service, or repair s, with engine running. Stop auger. Stop engine. Remove key. Dis connect spark plug wire an d secure w ire away from spark plug. Be fo re tilting machin e, drain all the fu el from fuel tank. A llow engine to run, outdoors where fumes ...

  • Snapper 8246, 9266E, 11306, 9266 - page 16

    16 Section 4 - REPA IR & A DJUSTMENTS 4.1.5. SKID SHOE A DJUSTM ENT NOTE: It is recom m ended to raise the auger/im peller housing when c learing rough or gr aveled surfac es. To raise auger/im peller the s kid s hoes should be lowered. 1. Tilt m achine up and plac e a wooden block under auger/im peller housing. 2. Loosen bolts on both skid sho ...

  • Snapper 8246, 9266E, 11306, 9266 - page 17

    17 Section 4 - REPA IR & A DJUSTMENTS 4.1.6. SINGLE HA NDLE CONTROL A DJUSTM ENT IMPO RTANT: Standing in the oper ator’s position, the lef t handle bar lever is f or wheel drive engagement and disengagem ent. The r ight handle bar lever is f or auger/im peller engagem ent and disengagem ent. Hold both levers down to handle bar f or engagem en ...

  • Snapper 8246, 9266E, 11306, 9266 - page 18

    18 Section 4 - REPA IR & A DJUSTMENTS 4.1.7. AUGER SHEA R BOLT REPLACEMENT IMPO RTANT: If engine is operating corr ectly and auger/im peller drive belt is not dam aged or severed, but the auger/im peller does not rotate it is possibly the auger/impeller s haft shear bolt. 1. Rem ove shear bolt and nut f rom auger. Disc ard old shear bolt and nu ...

  • Snapper 8246, 9266E, 11306, 9266 - page 19

    19 TROUBLESHOOTING PROBL EM PROBA BLE CA USE CORRECTIVE A CTION Engine Will Not Start 1. Fuel tank empty. 1. Fill fuel tank with fresh fuel/oil mix . Using Recoil Starter 2. Engine needs choking and priming. 2. Mov e choke control to “CHOKE” position. Push primer bulb three times. 3. Spark plug wire disconnected. 3. Place spark plug wire onto s ...

  • Snapper 8246, 9266E, 11306, 9266 - page 20

    20 3 YEA R LIMITED WA RRA NTY For thr ee ( 3) years from purc hase date f or the original purc haser's residential, non- com m erc ial use, SNAPPER , through any authorized SNA PPER dealer will replace, fr ee of c harge (ex cept f or taxes where applicable), any part or parts found upon exam ination by the factory at McDonough, Georgia, to be ...

  • Snapper 8246, 9266E, 11306, 9266 - page 21

    21 NOTES _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _____ ...

  • Snapper 8246, 9266E, 11306, 9266 - page 22

    22 NOTES _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _____ ...

  • Snapper 8246, 9266E, 11306, 9266 - page 23

    23 NOTES _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _______________________________________________ _____ ...

  • Snapper 8246, 9266E, 11306, 9266 - page 24

    24 Safety Instructions & Operator’s Manual for TWO STAGE LARGE FRAM E SNOW THROWER SERIES 6 IMPORTA NT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufac tured. The labels on those e ngines contain ver y important e missions infor mation and critical safety warn ings. Read, U ...

Manufacturer Snapper Category Snow Blower

Documents that we receive from a manufacturer of a Snapper 8246, 9266E, 11306, 9266 can be divided into several groups. They are, among others:
- Snapper technical drawings
- 8246, 9266E, 11306, 9266 manuals
- Snapper product data sheets
- information booklets
- or energy labels Snapper 8246, 9266E, 11306, 9266
All of them are important, but the most important information from the point of view of use of the device are in the user manual Snapper 8246, 9266E, 11306, 9266.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Snapper 8246, 9266E, 11306, 9266, service manual, brief instructions and user manuals Snapper 8246, 9266E, 11306, 9266. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Snapper 8246, 9266E, 11306, 9266.

Similar manuals

A complete manual for the device Snapper 8246, 9266E, 11306, 9266, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Snapper 8246, 9266E, 11306, 9266 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Snapper 8246, 9266E, 11306, 9266.

A complete Snapper manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Snapper 8246, 9266E, 11306, 9266 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Snapper 8246, 9266E, 11306, 9266, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Snapper 8246, 9266E, 11306, 9266, that we can find in the current document
3. Tips how to use the basic functions of the device Snapper 8246, 9266E, 11306, 9266 - which should help us in our first steps of using Snapper 8246, 9266E, 11306, 9266
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Snapper 8246, 9266E, 11306, 9266
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Snapper 8246, 9266E, 11306, 9266 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Snapper 8246, 9266E, 11306, 9266?

Use the form below

If you did not solve your problem by using a manual Snapper 8246, 9266E, 11306, 9266, ask a question using the form below. If a user had a similar problem with Snapper 8246, 9266E, 11306, 9266 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)