English dropdown-ico

Manual Porter-Cable 447

17 pages 1.38 mb
Download

Go to site of 17

Summary
  • Porter-Cable 447 - page 1

    Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...

  • Porter-Cable 447 - page 2

    2 SAFETY GUIDELINES - DEFINITIONS indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,may result in minor or moderate inju ...

  • Porter-Cable 447 - page 3

    3 3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 4. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the ris ...

  • Porter-Cable 447 - page 4

    4 ADDITIONAL SPECIFIC SAFETY RULES SERVICE 1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 2. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance Section of this manual. Use of unauthorize ...

  • Porter-Cable 447 - page 5

    5  When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.  If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf an ...

  • Porter-Cable 447 - page 6

    6 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 vo ...

  • Porter-Cable 447 - page 7

    7 Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft. 0-2 18 18 18 16 16 14 14 12 12 2-3 18 18 16 14 14 12 12 10 10 3-4 18 18 16 14 12 12 10 10 8 4-5 18 18 14 12 12 10 10 8 8 5-6 18 16 14 12 10 10 8 8 6 6-8 18 16 12 10 10 8 6 6 ...

  • Porter-Cable 447 - page 8

    8 4. Remove blade retaining bolt, release blade lock and remove outer blade flange. 5. Retract telescoping guard and remove blade. INST ALLING THE BLADE 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Remove any sawdust that may have accumulated within guards and around arbor. Check the telescoping guard to insure it is in working order. 3. Clean inner bl ...

  • Porter-Cable 447 - page 9

    9 TO ADJUST DEPTH OF CUT FOR NORMAL CUTTING It is recommended that the depth of cut be adjusted so that the saw blade just protrudes through the thickness of material being cut. Adjust depth of cut as follows: 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Lift up depth adjustment locking lever (A) Fig. 4, at rear of saw. 3. Raise or lower saw housing un ...

  • Porter-Cable 447 - page 10

    10 90° AND 45° BEVEL POSITIVE STOPS The saw is equipped with adjustable positive stops at both 90° (A) Fig. 6, and 45° (B) Fig. 6. It is recommended that the accuracy of these stops be checked periodically and adjustments be made as necessary. These procedures are explained fully in the following sections of this manual. BACK CUTS This saw can ...

  • Porter-Cable 447 - page 11

    11 TO ADJUST 90° POSITIVE STOP 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Set bevel stop sleeve to normal position (see Fig. 6). 3. Loosen bevel adjustment knob (A) Fig. 5, and position base for 90° cut being sure that the bevel stop sleeve is against the 90° stop screw. 4. Turn saw upside down, retract telescoping guard and check squareness of bl ...

  • Porter-Cable 447 - page 12

    12 BLADE WRENCH STORAGE Blade wrench storage is provided in the bottom of the saw handle (see Fig. 10). Position the handle end of the blade wrench into the storage slot and push forward until seated. INST ALLING SAWDUST EXHAUST NOZZLE An exhaust nozzle is provided to direct sawdust away from operator and the line of cut. This nozzle can be install ...

  • Porter-Cable 447 - page 13

    13 RIP GUIDE A rip guide (A), Fig. 13, is available as an accessory. Install rip guide as follows: 1. DISCONNECT TOOL FROM POWER SOURCE. 2 . Insert rip guide through slot in right side of saw base. Slide the guide in until it extends through the slot in left side of base. 3. Position the compression spring to the thumb screw (supplied with the rip ...

  • Porter-Cable 447 - page 14

    14 Do not force the cut. Let the saw do the cutting at the rate of speed permitted by the type of cut and the material being cut. When the cut is completed, release the switch and allow the blade to stop before lifting the saw from the work. On through-cuts, be sure the lower blade guard is closed, before setting the saw down. CROSS-CUTTING Cutting ...

  • Porter-Cable 447 - page 15

    15 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. WEAR ANSI Z87.1 SAFETY GLASSES WHILE USING COMPRESSED AIR. F AILURE TO ST ART Should your tool fail t ...

  • Porter-Cable 447 - page 16

    16 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter- Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter-Cable • ...

  • Porter-Cable 447 - page 17

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Manufacturer Porter-Cable Category Saw

Documents that we receive from a manufacturer of a Porter-Cable 447 can be divided into several groups. They are, among others:
- Porter-Cable technical drawings
- 447 manuals
- Porter-Cable product data sheets
- information booklets
- or energy labels Porter-Cable 447
All of them are important, but the most important information from the point of view of use of the device are in the user manual Porter-Cable 447.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Porter-Cable 447, service manual, brief instructions and user manuals Porter-Cable 447. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Porter-Cable 447.

Similar manuals

A complete manual for the device Porter-Cable 447, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Porter-Cable 447 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Porter-Cable 447.

A complete Porter-Cable manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Porter-Cable 447 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Porter-Cable 447, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Porter-Cable 447, that we can find in the current document
3. Tips how to use the basic functions of the device Porter-Cable 447 - which should help us in our first steps of using Porter-Cable 447
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Porter-Cable 447
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Porter-Cable 447 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Porter-Cable 447?

Use the form below

If you did not solve your problem by using a manual Porter-Cable 447, ask a question using the form below. If a user had a similar problem with Porter-Cable 447 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)