English dropdown-ico

Manual Honeywell RM7840M

16 pages 0.47 mb
Download

Go to site of 16

Summary
  • Honeywell RM7840M - page 1

    INSTALLATION INSTRUCTIONS 66- 1085- 3 ® U.S. Registered T rademark Copyright © 2002 Honeywell • All Rights Reserved RM7800E,G,L,M; RM7840E,G,L,M 7800 SERIES Relay Modules APPLICATION The Hon eywell RM7800/R M784 0 Relay Mo dules are microproce ssor-based i ntegrate d burner c ontrols fo r automati cally fi red gas , oil, or combin ation fuel si ...

  • Honeywell RM7840M - page 2

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MO DULES 66-1085—3 2 WARNING Fire or Ex plosion Haza rd. Can cause property dama ge, sev ere injury , or deat h. T o prevent possibl e hazardous burner operation, verify safety requirements each time a co ntrol is inst alled on a bur ner . WARNING Electrical Sh ock Hazard. Can cause serious injury ...

  • Honeywell RM7840M - page 3

    RM7800E,G ,L,M; RM78 40E,G,L,M 780 0 SERIES R ELAY MODULES 3 66-1085—3 4. All wir ing mu st co mply with all appli cable electric al codes, ordina nces and regula tions . Wiring , where required, must com ply wit h NEC, Class 1 (Line V oltage) wiring. 5. Recomm ended wire siz e and typ e: see T able 1. 6. Recomm ended groundi ng practi ces: see T ...

  • Honeywell RM7840M - page 4

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MO DULES 66-1085—3 4 Fig. 1. Inte rnal block diagram of the RM780 0L/RM7840L (See Fig. 2, 3, 4 or 5 for individ ual deta iled wiri ng instructions ). CONFIGURATION JUMPERS MICROCOMPUTER RESET PUSHBUTTON RUN/TEST SWITCH STATUS LEDs PLUG-IN PURGE TIMER CARD SAFETY RELAY CIRCUIT POWER SUPPLY KEYBOARD ...

  • Honeywell RM7840M - page 5

    RM7800E,G ,L,M; RM78 40E,G,L,M 780 0 SERIES R ELAY MODULES 5 66-1085—3 T able 2. Recommended Groundi ng Practice s. T able 3. T ermina l Ratings. . a The re lay modu le mu st have a n earth ground providin g a co nnection betwe en the subbase and th e cont rol pan el or the equipm ent. The earth g round wi re must b e capabl e of co nducti ng the ...

  • Honeywell RM7840M - page 6

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MO DULES 66-1085—3 6 T able 4. Combinat ions for T er minals 8, 9 , 10 and 21. T able 5. Explana tion of Eac h Combination . Mountin g RM78 00/RM 7840 Relay Module (Fig. 5) 1. Mount th e RM7800/RM 7840 verticall y on t he Q7800 Subbase , or mo unt hori zontally with th e knif e blad e termina ls po ...

  • Honeywell RM7840M - page 7

    RM7800E,G ,L,M; RM78 40E,G,L,M 780 0 SERIES R ELAY MODULES 7 66-1085—3 Fig. 2. Wiring subbase and sequence for RM7800 E,L/RM7840E,L . M12261C G L2 3 4 4 5 5 6 7 8 9 10 F (L1) 13 14 15 16 17 18 19 20 21 22 12 LOCKOUT INTERLOCKS (INC. AIR FLOW SWITCH) MASTER SWITCH LOW FIRE START SWITCH 5 SECOND IGNITION (EARLY SPARK TERMINATION) MAIN FUEL VALVE(S) ...

  • Honeywell RM7840M - page 8

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MO DULES 66-1085—3 8 Fig. 3. W iring subbase and sequen ce for RM7800 G/RM7840 G. RM7800G/RM7840G POWER OPERATING CONTROLS AND INTERLOCKS BURNER FLAME SIGNAL FIRING RATE MOTOR INITIATE (INITIAL POWERUP ONLY) POWER STANDBY PREPURGE HOLD DRIVE TO LOW FIRE POWER PILOT FLAME MAIN POWER PFEP 10 SEC. (4 ...

  • Honeywell RM7840M - page 9

    RM7800E,G ,L,M; RM78 40E,G,L,M 780 0 SERIES R ELAY MODULES 9 66-1085—3 Fig. 4. Wiring subbase and sequen ce for RM780 0M/RM7840 M. M12262A G L2 3 4 5 6 7 8 9 10 F (L1) 13 14 15 16 17 18 19 20 21 22 12 MASTER SWITCH LOW FIRE START SWITCH 5 SECOND IGNITION (EARLY SPARK TERMINATION) MAIN FUEL VALVE(S) BURNER CONTROLLER/LIMITS BURNER MOTOR (BLOWER) C ...

  • Honeywell RM7840M - page 10

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MO DULES 66-1085—3 10 Fig. 5. RM7800 /RM7840 R elay Module exploded vie w . SAFETY SHUTDOWN Safety Shutdown (Lockout) o ccurs if any of the following oc cur du ring the indicated period: 1. INITIA TE Period: a. Purge car d is n ot install ed or i s removed. b. Purge car d is b ad. c. Config uration ...

  • Honeywell RM7840M - page 11

    RM7800E,G ,L,M; RM78 40E,G,L,M 780 0 SERIES R ELAY MODULES 1 1 66-1085— 3 g. Lockout In terloc k opens d uring PREPURGE (RM7840E,L). h. Ignition /pilot valve/i ntermi ttent pi lot valv e term inal is energiz ed. i. Main v alve term inal i s energiz ed. j. Internal system fault o ccurred . k. P urge c ard i s rem oved. l. Purge car d is b ad. 4. P ...

  • Honeywell RM7840M - page 12

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MO DULES 66-1085—3 12 Ignition Trials 1. Pilo t F lame Es tabli shi ng Peri od ( PFEP ): a. With the firing rate mo tor at the l ow fire p ositio n: (1) The pilot valv e and igniti on transfo rmer , termina ls 8, 1 0 and 2 1, are ene rgized . The RM7800M has an i ntermitten t pilot valve, termina l ...

  • Honeywell RM7840M - page 13

    RM7800E,G ,L,M; RM78 40E,G,L,M 780 0 SERIES R ELAY MODULES 13 66-1085—3 Keyboard Disp lay Module (VFD) The Keyboard Display Module (see Fig. 5) is provided with the RM7800 R elay Module (but is not requir ed f or operatio n) and is an op tion fo r the RM7840 Rel ay Modu le. Th e first line of the V acuum Fluo resce nt Display (VFD) p rovid es: ? ...

  • Honeywell RM7840M - page 14

    RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MO DULES 66-1085—3 14 T able 7. Sit e Configurable J umper Optio ns. a Pilot V alv e /First Sta ge Oi l V alve (V alve/S tart) T erminal 21. b A 30 sec ond MFEP c an be a ccompl ished by addin g a ju mper wire be tween T erminals 19 and 5. SER VICE NOTE :Clipp ing and re movi ng a s ite-config urab ...

  • Honeywell RM7840M - page 15

    RM7800E,G ,L,M; RM78 40E,G,L,M 780 0 SERIES R ELAY MODULES 15 66-1085—3 T able 8. Static C heckout. Te s t No. RM780 0/ RM7840 Models Te s t Jumper s V oltmete r Normal Opera tion If Operation is Abnormal, Check the Items Listed Be low 1 All None 4-L2 Line volta ge at T erminal 4. 1. Maste r Switch. 2. Power conne cted to the Mast er Switch . 3. ...

  • Honeywell RM7840M - page 16

    66-1085—3 G.R. Rev . 02-02 www .honeywell.com RM7800E,G ,L,M; RM7840E,G ,L,M 7800 SERIES RELAY MO DULES Autom ati on and Contr ol Solut ions Honeywell Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, M N 55422 Scarborough, Ont ario M1V 4Z9 Printed in U.S.A. on recycled paper containing at least 10% pos ...

Manufacturer Honeywell Category Thermostat

Documents that we receive from a manufacturer of a Honeywell RM7840M can be divided into several groups. They are, among others:
- Honeywell technical drawings
- RM7840M manuals
- Honeywell product data sheets
- information booklets
- or energy labels Honeywell RM7840M
All of them are important, but the most important information from the point of view of use of the device are in the user manual Honeywell RM7840M.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Honeywell RM7840M, service manual, brief instructions and user manuals Honeywell RM7840M. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Honeywell RM7840M.

Similar manuals

A complete manual for the device Honeywell RM7840M, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Honeywell RM7840M by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Honeywell RM7840M.

A complete Honeywell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Honeywell RM7840M - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Honeywell RM7840M, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Honeywell RM7840M, that we can find in the current document
3. Tips how to use the basic functions of the device Honeywell RM7840M - which should help us in our first steps of using Honeywell RM7840M
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Honeywell RM7840M
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Honeywell RM7840M in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Honeywell RM7840M?

Use the form below

If you did not solve your problem by using a manual Honeywell RM7840M, ask a question using the form below. If a user had a similar problem with Honeywell RM7840M it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)