English dropdown-ico

Manual Quadra-Fire QV36DC-A

36 pages 3.56 mb
Download

Go to site of 36

Summary
  • Quadra-Fire QV36DC-A - page 1

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 1 Model: QV36DC-A Owner ’ s Manual Installation and Operation • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any appliance - Do not touch any electrical switch. Do ...

  • Quadra-Fire QV36DC-A - page 2

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 2 These units MUST use one of the vent systems described in the Installing the Fireplace section of the Owner ’ s Manual . NO OTHER vent systems or components MA Y BE USED . This gas fi replace and vent assembly MUST be vented directly to the outside and MUST NEVER be attached to a chimney s ...

  • Quadra-Fire QV36DC-A - page 3

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 3 T ABLE OF CONTENTS Safety and W arning Information .................................................2 Service Parts Lists ....................................................................... 4 Section 1: Approvals and Codes ................................................ 7 Appliance Certi ...

  • Quadra-Fire QV36DC-A - page 4

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 7 1 Approvals and Codes Appliance Certi fi cation The fi replace model discussed in this Owner ’s Manual has been tested to certi fi cation standards and listed by the applicable laboratories. MODELS: QV36DC-A LABORA TOR Y : Underwriters Laboratories, Inc. (UL) TYPE: V ented Gas Fireplace ...

  • Quadra-Fire QV36DC-A - page 5

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 8 Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exh ...

  • Quadra-Fire QV36DC-A - page 6

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 9 2 Getting Started Introducing Quadra-Fire Gas Fireplaces Quadra-Fire direct vent gas fi replaces are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. The information contained in this Owner ’s Manual , unless ...

  • Quadra-Fire QV36DC-A - page 7

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 10 Figure 1. Diagram of the QV36DC-A TOP ST ANDOFFS HOOD ELECTRICAL ACCESS GAS CONTROLS RA TING PLA TE AND LABELS GAS LINE ACCESS 41 1/8 [1044mm] 38 [965mm] 36 1/8 [916mm] 25 1/4 [642mm] 34 5/8 [879mm] 8 5/8 [219mm] VENT COLLARS ELECTRICAL ACCESS 26 7/8 [682mm] 12 3/4 [323mm] 3 1/2 [90mm] GAS L ...

  • Quadra-Fire QV36DC-A - page 8

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 11 3 Installing the Fireplace Step 1. Locating the Fireplace The following diagram shows space and clearance require- ments for locating a fi replace within a room. A B C D E 42” 22” 36” 51” 72” Minimum Clearances from the Fireplace to Combustible Materials Inches mm Glass Front .... ...

  • Quadra-Fire QV36DC-A - page 9

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 12 Framing should be c o n s t r u c t e do f2X4 lumber or heavier . Shows center of 10” x 12” vent framing holes for top and rear venting. The center of the hole is one (1) inch (25.4mm) above the center of the horizontal vent pipe. Noncombustible zone is defined by 3” above the elbow fo ...

  • Quadra-Fire QV36DC-A - page 10

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 13 Figure 4. DVP-Series Direct V ent Component Speci fi cations (5-inch inner pipe / 8-inch outer pipe) NOTE: PIPES OVERLAP 1-1/4 INCHES A T EACH JOINT . DVP90ST 12-9/16 11 - 1 / 4 7-1/4 1-1/4 TYP 1/2 TYP 8-9/16 DVP36 DVP48 48 24 36 4 6 DVP4 DVP6 12 DVP12 2 MIN. DVP12A 12-3/16 MAX. DVP24 9-7/8 ...

  • Quadra-Fire QV36DC-A - page 11

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 14 Figure 5. V ent System Components and T ermination Kits Identifying V ent Components The vent systems installed on this gas fi replace may include one, two, or three 90° elbow assemblies. The relationships of vertical rise to horizontal run in vent con fi gurations using 90° elbows MUST ...

  • Quadra-Fire QV36DC-A - page 12

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 15 Figure 6. Straight Up V ertical V enting STRAIGHT UP VERTICAL VENTING V (FT .) 40’ MAX. (12.4 M) Flue Restrictor Instructions 1. Remove screws with a 1/4 nut driver . Adjust to desired position per table. See Flue Restricting chart. NOTE: On vertical vent- ing con fi gurations over 20 fee ...

  • Quadra-Fire QV36DC-A - page 13

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 16 HORIZONT AL VENTING Kit No. H Max. Run DVP-TRAP 24” (610 mm) Figure 10. Corner Installation NOTE: This model is tested and approved to use 45° elbows in corner installations. However , 90° elbows will result in better performance. Figure 9. Horizontal Installation 90-DEGREE ELBOWS 45-DEG ...

  • Quadra-Fire QV36DC-A - page 14

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 17 V H 1’ MIN. (305mm) 2’ MAX. (610mm) 2’ MIN. (610mm) 4’ MAX. (1.22m) 3’ MIN. (914mm) 6’ MAX. (1.86m) 4’ MIN. (1.22m) 8’ MAX. (2.4m) V+H=40’ MAX. (12.4m) H = 8’ MAX. (2.4m) NOTE: On vertical venting configurations where the vertical component is over 10 feet install the ver ...

  • Quadra-Fire QV36DC-A - page 15

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 18 Figure 13. V enting with T wo 90° Elbows VENTING WITH TWO (2) 90° ELBOWS V H H + H 1 1´ MIN. (305 mm) 2´ MAX. (610 mm) 5´ MAX. (1.52m) 2´ MIN. (610 mm) 4´ MAX. (1.22 m) 10´ MAX. (3.1m) 3´ MIN. (914 mm) 6´ MAX. (1.86 m) 15´ MAX. (4.65m) 4´ MIN. (1.22 m) 8´ MAX. (2.48 m) 20´ MAX. ...

  • Quadra-Fire QV36DC-A - page 16

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 19 Figure 15. V enting with three 90° elbows VENTING WITH THREE (3) 90° ELBOWS 1´MIN. (305mm) 2´MAX. (610mm) 5´MAX. (1.52m) 2´MIN. (610mm) 4´MAX. (1.22m) 10´MAX. (3.1m) 3´MIN. (914mm) 6´MAX. (1.86m) 15´MAX. (4.65m) 4´MIN. (1.22m) 8´MAX. (2.48m) 20´MAX. (6.2m) V+H+H 1 +H 2 = 40 ´ ...

  • Quadra-Fire QV36DC-A - page 17

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 20 VENTING WITH THREE (3) 90° ELBOWS V (FT .) H (FT .) 1’ MIN. (305mm) 5’ MAX. (1.52m) 2’ MIN. (610mm) 10’ MAX. (3.1m) 3’ MIN. (914mm) 15’ MAX. (4.65m) 4’ MIN. (1.22m) 20’ MAX. (6.2m) NOTE: H + H 1 = 20’ MAX. (6.2m) V + V 1 + H + H 1 = 40’ MAX. (12.4m) V (FT .) H + H 1 (FT ...

  • Quadra-Fire QV36DC-A - page 18

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 21 V enting Out the T op V ent Remove the two screws in the top vent collar seal cap and remove the top vent collar seal cap and the two pieces of insulation inside the top two starting collars (See Figure 17). Remove the heat shield from inside the TOP fi ve inch fl ue from outside of the ? ...

  • Quadra-Fire QV36DC-A - page 19

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 22 Figure 19. HEA T SHIELD 3” MIN. (76 mm) COMBUSTIBLE SURF ACE T o Install the Heat Shield: 1. Determine if the heat shield is required. Do so by mea- suring the vertical distance between the top horizontal surface of the elbow to any combustible surface above. If the distance is more than 4 ...

  • Quadra-Fire QV36DC-A - page 20

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 23 5. Install Firestops For Horizontal Runs - Firestops are REQUIRED on both sides of a combustible wall through which the vent passes. NOTE: Model DVP-TRAP does not need an exterior fi restop on an exterior combustible wall. T o install fi restops for horizontal runs that pass through either ...

  • Quadra-Fire QV36DC-A - page 21

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 24 For V ertical Runs - One ceiling fi restop is REQUIRED at the hole in each ceiling through which the vent passes. T o install fi restops for vertical runs that pass through ceilings: • Position a plumb bob directly over the center of the verti- cal vent component. • Mark the ceiling to ...

  • Quadra-Fire QV36DC-A - page 22

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 25 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 4.4 Minimum Clearances for T ermination A = 12 inches................. clearances above grade, veranda, porch, deck or balcony B = 12 inches................. clearances to window or door that may be opened, ...

  • Quadra-Fire QV36DC-A - page 23

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 26 For V ertical T erminations - T o locate the vent and install the vent sections: • Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint. • Make the outline of the roof hole around the centerpoint nail. • The size of the roof hole f ...

  • Quadra-Fire QV36DC-A - page 24

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 27 Step 4. Positioning, Leveling, and Securing the Fireplace • Place the fi replace into position. • Level the fi replace from side to side and from front to back. • Shim the fi replace with non-combustible material, such as sheet metal, as necessary . • Secure the fi replace to the ...

  • Quadra-Fire QV36DC-A - page 25

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 28 • Insert insulation from the outside of the fi replace and pack the insulation tightly to totally seal between the pipe and the outer casing. • At the gas line access hole the gap between the supply piping and gas access hole can be plugged with non- combustible insulation to prevent co ...

  • Quadra-Fire QV36DC-A - page 26

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 29 Optional Accessories Optional fan and remote control kits require that 1 10-120 V AC be wired to the factory installed junction box before the fi replace is permanently installed. W all Switch Position the wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or le ...

  • Quadra-Fire QV36DC-A - page 27

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 30 Step 9. Finishing Figure 36 shows the minimum vertical and corresponding maximum horizontal dimensions of fi replace mantels or other combustible projections above the top front edge of the fi replace. See Figures 2 and 3 for other fi replace clearances. Only non-combustible materials may ...

  • Quadra-Fire QV36DC-A - page 28

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 31 Figure 38. Figure 39. Figure 40. Figure 39. Figure 42. Position the right wall all the way to back wall. Secure in po- sition same as was done for the left wall (see Figure 42). Installing the T rim Combustible materials may be brought up to the speci fi ed clearances on the side and top fr ...

  • Quadra-Fire QV36DC-A - page 29

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 32 Placing the Ember Material • Release the four glass latches on the glass frame. Re- move glass door from the unit. • Glowing Ember material can be placed without remov- ing logs. Place a single layer of dime size and thickness pieces on exposed area of burner front and burner center . St ...

  • Quadra-Fire QV36DC-A - page 30

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 33 1. T urn off all electric power to the appliance if service is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position. 4. Push in gas control knob slightly and turn clock- wise to OFF”. Do not force. 5. Close control access panel. 5. Turn knob on gas control co ...

  • Quadra-Fire QV36DC-A - page 31

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 34 After the Installation LEA VE THIS INST ALLA TION MANUAL WITH THE APPLIANCE FOR FUTURE REFERENCE. 4 Maintaining and Servicing Y our Fireplace Fireplace Maintenance Although the frequency of your fi replace servicing and maintenance will depend on use and the type of installation, you should ...

  • Quadra-Fire QV36DC-A - page 32

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 35 A. Standing Pilot Ignition System Symptom Possible Causes Corrective Action 1. After repeated triggering of the red or black piezo ignitor button, the spark ignitor will not light the pilot. a. Defective ignitor . Check the spark at the electrode and pilot. If no spark and electrode wire is ...

  • Quadra-Fire QV36DC-A - page 33

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 36 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter should read greater than 125mV ...

  • Quadra-Fire QV36DC-A - page 34

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 37 Limited Lifetime W arranty Î ...

  • Quadra-Fire QV36DC-A - page 35

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 38 Limited Lifetime W arranty Î ...

  • Quadra-Fire QV36DC-A - page 36

    Quadra-Fire • QV36DC-A • 2161-900 Rev . C • 6/09 39 Contact Information - NOTES - ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ___________________ ...

Manufacturer Quadra-Fire Category Indoor Fireplace

Documents that we receive from a manufacturer of a Quadra-Fire QV36DC-A can be divided into several groups. They are, among others:
- Quadra-Fire technical drawings
- QV36DC-A manuals
- Quadra-Fire product data sheets
- information booklets
- or energy labels Quadra-Fire QV36DC-A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Quadra-Fire QV36DC-A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Quadra-Fire QV36DC-A, service manual, brief instructions and user manuals Quadra-Fire QV36DC-A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Quadra-Fire QV36DC-A.

Similar manuals

A complete manual for the device Quadra-Fire QV36DC-A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Quadra-Fire QV36DC-A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Quadra-Fire QV36DC-A.

A complete Quadra-Fire manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Quadra-Fire QV36DC-A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Quadra-Fire QV36DC-A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Quadra-Fire QV36DC-A, that we can find in the current document
3. Tips how to use the basic functions of the device Quadra-Fire QV36DC-A - which should help us in our first steps of using Quadra-Fire QV36DC-A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Quadra-Fire QV36DC-A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Quadra-Fire QV36DC-A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Quadra-Fire QV36DC-A?

Use the form below

If you did not solve your problem by using a manual Quadra-Fire QV36DC-A, ask a question using the form below. If a user had a similar problem with Quadra-Fire QV36DC-A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)