English dropdown-ico

Manual American Dynamics AD1686B

28 pages 0.27 mb
Download

Go to site of 28

Summary
  • American Dynamics AD1686B - page 1

    Model AD1686B General Purpose Indoor/Outdoor Receiver Installation and Operating Instructions This manual describes the installation and operating procedures for the AD1686B Dual Channel Receiver. Receivers are designed as the remote control device for operation of a motorized pan and tilt unit and a motorized lens unit. Since camera sites are ofte ...

  • American Dynamics AD1686B - page 2

    This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the purchaser under a license for use on a single system. NOTE: Information furnished by SENSORMATIC is believed to be ...

  • American Dynamics AD1686B - page 3

    The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301D ! W W W W A A A A R R R R N N N N II I I N N N N G G G G To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture. AMERICAN DYNAMICS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMO ...

  • American Dynamics AD1686B - page 4

    ...

  • American Dynamics AD1686B - page 5

    CONTENTS Page DESCRIPTION............................................................................... 1 FEA TURES ..................................................................................... 1 Pan/T ilt and Lens Control .......................................................... 1 Auxiliaries ............................................. ...

  • American Dynamics AD1686B - page 6

    ...

  • American Dynamics AD1686B - page 7

    AD1686B DESCRIPTION and FEATURES DESCRIPTION The AD1686B Receiver is a 2-channel controller used with Matrix Switching Systems to control pan, tilt, zoom, focus, iris, and auxiliary functions at a camera site. This Receiver is classified as a dual-channel type since two independent control channels are supplied, Channel A and Channel B. The output ...

  • American Dynamics AD1686B - page 8

    SETUP AD1686B 2 SETUP Pan/Tilt Output Voltage The Pan/Tilt output voltages of each channel can be independently set for either 24 VAC or line voltage (120VAC or 230VAC). Two slide switches, S4 and S5 (see Figure 1), control the output voltages for the channels. Switch S4 controls the voltage of Channel A, and switch S5 controls the voltage of chann ...

  • American Dynamics AD1686B - page 9

    Table 2 - S3 Configuration Select Receiver Configuration Switch S3 general description is listed below. This table is continued on page 4 to describe the switch settings in detail, with a list of individual switch position settings. Switch Position FUNCTION SW1 selects channel B type (auxiliary or camera) SW2 selects auxiliary type SW3 selects auxi ...

  • American Dynamics AD1686B - page 10

    Table 2 - S3 Configuration Select (Continued from page 3) L = left ("off"); R = right ("on") SW1 - Channel B Type - The AD1686B can act as a dual camera receiver with no auxiliaries, or as a single camera receiver with a set of auxiliaries. This is set using S3, SW1. SW1 FUNCTION L channel B is a camera pan/tilt channel R channe ...

  • American Dynamics AD1686B - page 11

    AD1686B SETUP 5 Table 3 - S1 Camera Number Switch Settings - Channel A L = left ("off"); R = right ("on") CAMERA Switch Position CAMERA Switch Position NUMBER 1 2 3 4 5 6 NUMBER 1 2 3 4 5 6 0 1 LLLLLL 3 3 LLLLLR 0 2 R LLLLL 3 4 R LLLLR 0 3 LR LLLL 3 5 LR LLLR 0 4 R R LLLL 3 6 R R LLLR 0 5 LLR LLL 3 7 LLR LLR 0 6 RL RL L L 3 8 RL ...

  • American Dynamics AD1686B - page 12

    SETUP AD1686B 6 Table 4 - S2 Camera Number Switch Settings or Auxiliary Settings Channel B L = left ("off"); R = right ("on") CAMERA Switch Position CAMERA Switch Position NUMBER 1 2 3 4 5 6 NUMBER 1 2 3 4 5 6 0 1 LLLLLL 3 3 LLLLLR 0 2 R LLLLL 3 4 R LLLLR 0 3 LR LLLL 3 5 LR LLLR 0 4 R R LLLL 3 6 R R LLLR 0 5 LLR LLL 3 7 LLR LLR ...

  • American Dynamics AD1686B - page 13

    INSTALLATION This installation should be made by qualified service personnel and should conform to all local codes. Safeguards must be taken to avoid unintentional operation by employees and maintenance personnel working about the premises, by falling objects, by customers, by building vibration, and by similar causes. Preparation There are several ...

  • American Dynamics AD1686B - page 14

    CONNECTIONS Code Line Connections The AD Code Line connection to the Receiver is made with user-supplied, shielded 2-wire twisted pair, Belden 8760 or equivalent (for Plenum use Belden 88760 or equivalent). The maximum code line length is 5000 feet. The code line connector, labeled J6, is a three-position screw- terminal located on the PCB near the ...

  • American Dynamics AD1686B - page 15

    AD1686B CONNECTIONS Pan/Tilt and Lens Connections The AD1686B Receiver connection to a Pan/Tilt and a motorized Lens is with a 12-pin connector. This connector, for Channel A, is located on the main PCB, to the right of the DIP switches S1 and S2, and is labeled J5 (see Figure 1, page 3). When the Receiver is set for dual-camera operation, a second ...

  • American Dynamics AD1686B - page 16

    CONNECTIONS AD1686B 10 Table 5 - Dual Pan/Tilt and Lens 12-pin Connector Pinout Channel A - J5 PIN No. FUNCTION Pan/Tilt PINOUT LENS PINOUT 01 Tilt Up _____________________ ____________________ 02 Tilt Down _____________________ ____________________ 03 Pan/Tilt Common _____________________ ____________________ 04 Pan Right _____________________ ___ ...

  • American Dynamics AD1686B - page 17

    AD1686B CONNECTIONS Auxiliary Connections When the AD1686B Receiver is set for single camera operation with auxiliaries, connection of auxiliary equipment to Channel B is made to the 12-pin connector, labeled J4, located on the Receiver PCB. See Figure 1, page 3. The camera Pan/Tilt and Lens connections for Channel A is made as described on pages 9 ...

  • American Dynamics AD1686B - page 18

    Pre-position (Preset) Connections The AD1686B Receiver connection to the Pan/Tilt and Lens pre-position servo unit is with a 9-pin connector labeled J2 (see Figure 1, page 3). For dual camera channel operation, a second 9-pin connector, labeled J3, is used for Channel B. Table 7, page 13, lists the pin designations from the Receiver to the Pan/Tilt ...

  • American Dynamics AD1686B - page 19

    AD1686B CONNECTIONS 13 Table 7 - Pre-position Pan/Tilt and Lens 9-pin Connector Pinout Channel A - J2 PIN No. FUNCTION Pan/Tilt PINOUT LENS PINOUT 01 (+) REF _____________________ ____________________ 02 Pan _____________________ ____________________ 03 Tilt _____________________ ____________________ 04 Focus _____________________ _________________ ...

  • American Dynamics AD1686B - page 20

    CONNECTIONS AD1686B Power Input Connections Refer to the instructions provided with the enclosure for suitable conduit connectors (when required), and mounting and caution information. Two type PG-16 liquid tight fittings are supplied for use with cord diameters from .395" to .551", and are to be mounted in the larger holes in the enclosu ...

  • American Dynamics AD1686B - page 21

    TYPICAL SYSTEM CONNECTIONS ...

  • American Dynamics AD1686B - page 22

    TYPICAL SYSTEM CONNECTIONS AD2150 Controller to AD1686B MAXIMUM DISTANCE between AD1686B and AD2150 is 5000 Ft, using shielded, 18 AWG cable AD2150 AD1686B BWS RS232 PORTS 123 KEYBOARDS 2345 CAMERAS ALARMS RELAY 120V 60Hz CODE BWS BWS BWS BWS MONITORS 1234 5 2468 1 0 1 2 1 4 1 6 1 8 2 0 2 2 2 4 2 6 2 8 3 0 3 2 13579 1 1 1 3 1 5 1 7 1 9 2 1 2 3 2 ...

  • American Dynamics AD1686B - page 23

    TYPICAL SYSTEM CONNECTIONS AD1996 Controller to AD2091 Code Generator, to AD1686B AD1686B AD2091 AD1996 ABCDEF ON OFF ABCDEF ON OFF ABCDEF ON OFF ABCDEF ON OFF B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W S B W ...

  • American Dynamics AD1686B - page 24

    TYPICAL SYSTEM CONNECTIONS AD1686B to AD1240P Pan/Tilt with Pre-position AD1686B 1240P PAN/TILT C-4 Code PWR F2 F1 S5 S4 24V 120V 24V 120V J2 J5 J3 J4 S3 8 1 OFF ON S1 6 1 S2 6 1 W S B J6 AD1240P 13-pin Connector, Pan/Tilt pins: 1. PAN/TILT COMMON 2. PAN RIGHT 3. PAN LEFT 4. TILT UP 5. TILT DOWN AD1240P 13-pin Connector, Preset pins: 7. +REF 8. PAN ...

  • American Dynamics AD1686B - page 25

    INDEX ...

  • American Dynamics AD1686B - page 26

    INDEX AD1686B Auto and Random Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Auxiliaries Configuration Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 P ...

  • American Dynamics AD1686B - page 27

    ...

  • American Dynamics AD1686B - page 28

    SPECIFICATIONS Supply Voltage: AD1686B 120 VAC, 50/60 Hz AD1686B-X 230 VAC, 50 Hz Power: 30 W (standby) AD1686B: 1240 W maximum input @ 120 VAC AD1686B-X 1420 W maximum input @ 230 VAC Mounting: Surface Mount Size: 15.5" H x 12.8" W x 6.7" D (394 x 325 x 170 mm) Weight: 16 lbs. (7.3 Kg) An American Dynamics Product Designed and built ...

Manufacturer American Dynamics Category Receiver

Documents that we receive from a manufacturer of a American Dynamics AD1686B can be divided into several groups. They are, among others:
- American Dynamics technical drawings
- AD1686B manuals
- American Dynamics product data sheets
- information booklets
- or energy labels American Dynamics AD1686B
All of them are important, but the most important information from the point of view of use of the device are in the user manual American Dynamics AD1686B.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals American Dynamics AD1686B, service manual, brief instructions and user manuals American Dynamics AD1686B. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product American Dynamics AD1686B.

Similar manuals

A complete manual for the device American Dynamics AD1686B, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use American Dynamics AD1686B by users. Manuals are usually written by a technical writer, but in a language understandable to all users of American Dynamics AD1686B.

A complete American Dynamics manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual American Dynamics AD1686B - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the American Dynamics AD1686B, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the American Dynamics AD1686B, that we can find in the current document
3. Tips how to use the basic functions of the device American Dynamics AD1686B - which should help us in our first steps of using American Dynamics AD1686B
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with American Dynamics AD1686B
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of American Dynamics AD1686B in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning American Dynamics AD1686B?

Use the form below

If you did not solve your problem by using a manual American Dynamics AD1686B, ask a question using the form below. If a user had a similar problem with American Dynamics AD1686B it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)