English dropdown-ico

Manual Pelco III

28 pages 1.04 mb
Download

Go to site of 28

Summary
  • Pelco III - page 1

    ® INST ALLA TION Pressurized Spectra III ™ Series English Español Português Italiano Français Deutsch C2478M-B-ML (2/05) ...

  • Pelco III - page 2

    ...

  • Pelco III - page 3

    C2478M-B-ML (2/05) 3 English Español Português Italiano Français Deutsch REMARQUE : Ce manuel est destiné à être un outil de référence lors de l'installation de votre système. Pour faciliter l'installation et obtenir les meilleurs résultats possible, assemblez, pressurisez et testez le système de dôme avant de l'installer ...

  • Pelco III - page 4

    4 C2478M-B-ML (2/05) Preinstallation English 1 Loosen the V-band attached to the back box and let it hang to the side. 2 Prepare the lower dome for installation: a. Remove the O-ring from the lower dome. b. Lightly apply O-ring lubricant (supplied) to the O-ring. c. Reinstall the O-ring in the groove on the trim ring. IMPORT ANT : Use the supplied ...

  • Pelco III - page 5

    C2478M-B-ML (2/05) 5 English 4 Install the dome drive: a. Set the DIP switches located on the side of the dome drive. Refer to the labels located on the top of the dome drive or to the Quick Start Guide shipped with the dome drive. NOTE: No DIP switch settings are required for Coaxitron control. b. Line up the blue (A) and red (B) tabs with the blu ...

  • Pelco III - page 6

    6 C2478M-B-ML (2/05) Site Installation English 1 Feed the supplied wiring harness into the front of the mount and out the back of the mount. Connect the wires as required. Refer to T ables A, B, and C for cable and wiring information. Fasten the mount to the mounting surface. Refer to the instructions supplied with the mount. 2 Remove the back box ...

  • Pelco III - page 7

    C2478M-B-ML (2/05) 7 English Minimum cable requirements: 75 ohms impedance All-copper center conductor All-copper braided shield with 95% braid coverage NOTE: These are the recommended maximum distances for 24 V AC appli- cations and are calculated with a 10 percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC- ...

  • Pelco III - page 8

    8 C2478M-B-ML (2/05) Preinstalación Español 1 Afloje la V-band que rodea la caja posterior y deje que cuelgue hacia el lateral. 2 Prepare el domo inferior para la instalación: a. Quite la junta O-ring del domo inferior . b. Aplique sobre la junta O-ring una pequeña cantidad de lubricante para O-rings (suministrado). c. V uelva a instalar la ju ...

  • Pelco III - page 9

    C2478M-B-ML (2/05) 9 Español 4 Instale la unidad del domo: a. Configure las posiciones de los conmutadores DIP ubicados en el lateral de la unidad del domo. Consulte las etiquetas ubicadas en la parte superior de la unidad del domo, o bien la Guía de inicio rápido enviada junto con la unidad del domo. NOT A: No se requiere la configuración de ...

  • Pelco III - page 10

    10 C2478M-B-ML (2/05) Instalación en la ubicación Español 1 Ponga el arnés de cableado suministrado desde el frente de la montura y desde atrás de la parte posterior de la montura. Conecte los cables según se requiera. Consulte las T ablas A, B y C para obtener información sobre el cableado. Ajuste la montura a la superficie de montaje. Con ...

  • Pelco III - page 11

    C2478M-B-ML (2/05) 11 Español Requerimientos mínimos para cables: 75 ohmios de impedancia Conductor con núcleo de cobre Blindaje entrelazado de cobre con cobertura de entrelazado del 95% NOT A: Las siguientes son las distancias máximas recomendadas para las aplicaciones que funcionan a 24 VCA y están calculadas en base a una caída de voltaje ...

  • Pelco III - page 12

    12 C2478M-B-ML (2/05) Pré-instalação Português 1 Solte a banda em V encaixada à back box e deixe-a dependurada para um dos lados. 2 Prepare o dome inferior para a instalação: a. Remova o O-ring do dome inferior . b. Aplique levemente o lubrificante do O-ring (fornecido) no mesmo. c. Reinstale o O-ring no sulco do anel de arremate. IMPORT AN ...

  • Pelco III - page 13

    C2478M-B-ML (2/05) 13 Português 4 Instale o dome drive: a. Ajuste as chaves DIP localizadas na lateral do dome drive. Consulte os rótulos na parte superior do dome drive, ou o Guia de Início Rápido fornecido com o dome drive. OBSERV AÇÃO: Nenhuma configuração para a chave DIP é necessária para o controle Coaxitron. b. Alinhe as abas azul ...

  • Pelco III - page 14

    14 C2478M-B-ML (2/05) Instalação no local Português 1 Conecte o módulo de ligação fornecido na entrada da parte frontal do suporte e na saída da parte posterior do suporte. Conecte os cabos conforme necessário. Consulte as T abelas A, B e C para obter informações sobre os cabos e ligações. Fixe o suporte à superfície de montagem. Cons ...

  • Pelco III - page 15

    C2478M-B-ML (2/05) 15 Português Requisitos mínimos por cabo: 75 ohms de impedância Condutor central totalmente de cobre Malha de blindagem totalmente de cobre, com 95% de cobertura OBSERV AÇÃO: Estas são as distâncias máximas recomendadas para aplicações em 24 VCA, e estão calculadas com uma queda de tensão de 10%. (10-% é geralmente o ...

  • Pelco III - page 16

    16 C2478M-B-ML (2/05) Pre-installazione Italiano 1 Allentare la striscia a V fissata al contenitore e lasciare che resti appesa di lato. 2 Preparare il dome inferiore per l'installazione: a. T ogliere l'O-ring dal dome inferiore. b. Applicare un leggero strato di lubrificante (in dotazione) all'O-ring. c. Rimontare l'O-ring ne ...

  • Pelco III - page 17

    C2478M-B-ML (2/05) 17 Italiano 4 Installare l'unità dome: a. Impostare gli interruttori DIP situati di lato all'unità dome. Consultare le etichette situate sulla sommità dell'unità dome, oppure la Guida di consultazione rapida in dotazione all'unità stessa. NOT A: per il controllo Coaxitron non occorrono interruttori DIP . ...

  • Pelco III - page 18

    18 C2478M-B-ML (2/05) Installazione in loco Italiano 1 Far passare il cablaggio in dotazione nella parte anteriore della staffa, facendolo uscire dalla parte posteriore. Collegare i fili secondo necessità. Consultare le T abelle A, B e C per informazioni sui cavi. Fissare la staffa alla superficie di montaggio. Consultare le istruzioni in dotazi ...

  • Pelco III - page 19

    C2478M-B-ML (2/05) 19 Italiano Requisiti minimi del cavo: Impedenza 75 ohm Conduttore centrale interamente in rame Schermatura intrecciata in rame con copertura del 95% NOT A: i dati seguenti indicano le distanze di collegamento massime per applicazioni a 24 V c.a. e sono calcolate con una caduta di tensione del 10% (10% è di solito la caduta di t ...

  • Pelco III - page 20

    20 C2478M-B-ML (2/05) Pré-installation Français 1 Détachez la bande en V attachée à l'embase et laissez-la pendre sur le côté. 2 Préparez le dôme inférieur pour l'installation : a. Retirez le joint torique du dôme inférieur . b. Appliquez une mince couche de lubrifiant pour joint torique (fourni) sur le joint torique. c. Réi ...

  • Pelco III - page 21

    C2478M-B-ML (2/05) 21 Français 4 Installez la commande de dôme : a. Réglez les commutateurs DIP situés sur le côté de la commande de dôme. Reportez-vous aux étiquettes situées en haut de la commande de dôme ou au guide de démarrage rapide joint à la commande de dôme. REMARQUE : Aucun réglage de commutateur DIP n'est nécessaire p ...

  • Pelco III - page 22

    22 C2478M-B-ML (2/05) Installation sur place Français 1 Faites passer le faisceau de câbles fourni par l'avant de la fixation et faites-le sortir par l'arrière de celle-ci. Connectez les fils selon le nécessaire. Reportez-vous aux tableaux A, B et C pour les câbles et les fils. Attachez la fixation sur la surface de fixation. Re ...

  • Pelco III - page 23

    C2478M-B-ML (2/05) 23 Français Critères minimums requis pour les câbles : Impédance 75 ohms Conducteur central entièrement en cuivre Écran entièrement en cuivre tressé avec 95 % de couverture du cuivre tressé REMARQUE : Ces valeurs sont les distances maximales recommandées pour les applications 24 Vca ; elles sont calculées avec une chut ...

  • Pelco III - page 24

    24 C2478M-B-ML (2/05) V orinstallation Deutsch 1 Lösen Sie das an der Back-Box befestigte V-Band, und lassen Sie es seitlich herunterhängen. 2 Bereiten Sie den unteren Dome zur Installation vor: a. Entfernen Sie den O-Ring vom unteren Dome. b. T ragen Sie etwas Dichtungsschmiermittel (im Lieferumfang enthalten) auf den O-Ring auf. c. Geben Sie de ...

  • Pelco III - page 25

    C2478M-B-ML (2/05) 25 Deutsch 4 Installieren Sie den Dome-Antrieb: a. Stellen Sie die DIP-Schalter seitlich am Dome-Antrieb ein (siehe Etikette auf der Oberseite des Dome-Antriebs oder Kurzanleitung , die im Lieferumfang enthalten ist). HINWEIS: Für die Coaxitron-Steuerung müssen keine DIP- Schaltereinstellungen vorgenommen werden. b. Richten Sie ...

  • Pelco III - page 26

    26 C2478M-B-ML (2/05) Installation vor Ort Deutsch 1 Schieben Sie den mitgelieferten Kabelsatz vorne in die Halterung und hinten aus der Halterung. Schließen Sie die Kabel an. In den T abellen A, B und C finden Sie V erkabelungsinformationen. Bringen Sie die Halterung auf der Montageoberfläche an. Lesen Sie hierzu die der Halterung beiliegenden ...

  • Pelco III - page 27

    C2478M-B-ML (2/05) 27 Deutsch Minimale Kabelanforderungen: Impedanz 75 Ohm Mittelleiter ganz aus Kupfer Geflochtene Abschirmung, V ollkupfer mit 95 % Abschirmungsabdeckung HINWEIS: Dies sind die empfohlenen maximalen Entfernungen für 24-V-WS-Anwendungen, wobei ein zehnprozentiger Spannungsabfall einberechnet ist. (10 Prozent ist im Normalfall der ...

  • Pelco III - page 28

    Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco III can be divided into several groups. They are, among others:
- Pelco technical drawings
- III manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco III
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco III.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco III, service manual, brief instructions and user manuals Pelco III. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco III.

Similar manuals

A complete manual for the device Pelco III, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco III by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco III.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco III - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco III, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco III, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco III - which should help us in our first steps of using Pelco III
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco III
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco III in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco III?

Use the form below

If you did not solve your problem by using a manual Pelco III, ask a question using the form below. If a user had a similar problem with Pelco III it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)