English dropdown-ico

Manual Kraun KR.PP

82 pages Not applicable
Download

Go to site of 82

Summary
  • Kraun KR.PP - page 1

    802.1 1b/g/n Wi reless LAN PC Card User Manual V ersion: 1.2 (April, 2007) ...

  • Kraun KR.PP - page 2

    COPYRIGHT Copyright ©2005/2006 by this company. A ll rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stor ed in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior ...

  • Kraun KR.PP - page 3

    C A T A L O G CHAPTER I: PRODUCT INFORMA TION 1-1 Introduction and safety information 1-2 Safety Information 1-3 System Requirements 1-4 Package Contents 1-5 Familiar with Y our New W ireless Network Card CHAPTER II: DRIVER INST ALLA TION AND CONFIGURA TION 2-1 Network Card and Driver Installation 2-2 Connect to W ireless Access Point 2-2-1 Using R ...

  • Kraun KR.PP - page 4

    2-7 WPS Configuration 2-8 About CHAPTER III: Soft-AP Function 3-1 Switch to AP Mode and Basic Configuration 3-2 Security Settings 3-3 Access Control 3-4 Connection T able 3-5 Event Log 3-6 Statist ics CHAPTER IV : APPENDIX 4-1 Hardware Specification 4-2 T roubleshooting 4-3 Glossary 4-4 FCC and Other Compliance S tatements ...

  • Kraun KR.PP - page 5

    Chapter I: Pr oduct Information 1-1 Introduction and safety information Thank you for purchasing this hi gh-speed 802.1 1b/g/Draft-N wireless network card! Excepting common wireless standards 802.1 1b/g, this wireless network card is also 802.1 1 Draft-N compatible - data transfer rate is 300Mbps, and that’ s six times faster than 802.1 1g wirele ...

  • Kraun KR.PP - page 6

    1-2 Safety Information In order to keep the safety of user s and your properties, please follow the following safety instructions: 1. This PCMCIA wireless network car d is designed for indoor use only . DO NOT expose this network card to direct sun light rain, or snow . 2. DO NOT put this network card at or near hot or humid places, like kitchen or ...

  • Kraun KR.PP - page 7

    1-3 System Requirements  An empty PCMCIA type II sl ot (CardBus Compatible)  W indows 2000, 2003, XP , or V ista operating system  CD-ROM drive  At least 100MB of available disk space ...

  • Kraun KR.PP - page 8

    1-4 Package Contents Before you starting to use this wireless network card, please check if there’ s anything missing in the package, and contact your dealer of purchase to claim for missing items: □ PCMCIA wireless network card (1 pcs) ………………………… 1 □ Quick installation guide (1 pcs) ………………………………… ...

  • Kraun KR.PP - page 9

    1-5 Familiar with your new wireless network card 1. PCMCIA Interface 2. CardBus golden stripe* 3. ‘Link’ LED 4. ‘Activity’ LED *This stripe should be faced up when inserted to PCMCIA slot of y our computer , or as instructed. LED Name Light Status Description On Linked to a wireless access point Link Off Not linked to any wireless access po ...

  • Kraun KR.PP - page 10

    CHAPTER II: DRIVER INST ALLA TION AND CONFIGURA TION 2-1 Network Card Installation Please follow the following instructions to install your new wireless network card: 1. Insert the PCMCIA wire less network card into an em pty PCMCIA slot of your computer when computer is switched on. For most of computers, you have to keep the golden stripe faced u ...

  • Kraun KR.PP - page 11

    2. The following message will appear on your computer , click ‘Cancel’ . 3. Insert device driver CDROM into the CD/DVD ROM drive of your computer , and execute ‘Setup.exe’ pr ogram in ‘Driver ’ folder . Please read the end user license agreemen t and click ‘Y es’ to accept license agreement. ...

  • Kraun KR.PP - page 12

    4. Y ou can choose the configuration tool used to configure the wireless network card here. It’ s recommended to select ‘Ralink Configuration T ool’, which provides fully access to all function of this wireless network card. If you prefer to use the wireless configuration tool provided by W indows XP or V ista, please select ‘ Microsoft Zer ...

  • Kraun KR.PP - page 13

    When you select one mode, plea se click ‘Next>’ to continue. If you see ‘Found New Hardwa r e’ message again, please ignore it and wait. 6. Please wait while the install proce dure is running. When you see this message, please click ‘Finish’ to co mplete the driver installation process. ...

  • Kraun KR.PP - page 14

    7. A new icon will appear at lower -right corner of your computer desktop, you can put the mouse cursor on the icon, and the status of wireless card will be displayed as a popup balloon. 8. When you want to configure your wireless connection, please right click on this icon, and a popup me nu will appear . Y ou can click ‘Launch Config Utilities? ...

  • Kraun KR.PP - page 15

    2-2 Connect to W ireless Access Point There are two ways you can configur e your wireless network card to connect to wireless access point: usi ng the Ralink configuration utility which comes with wireless card dr iver , and using built-in windows zero configuration utility . 2-2-1 Using Ralink Utility Please follow the following instructions to us ...

  • Kraun KR.PP - page 16

    Here are descriptions of every setup items: SSID: The Service Set IDentifier of wireless access point or other network device. Y ou can think it as the name of access point of wireless device. BSSID: The MAC address of wirele ss access point or other network device. Unlike SSID, BSSID of ever y access point or network device is unique, and will not ...

  • Kraun KR.PP - page 17

    Channel: Shows the channel number that access point or wireless device uses. Encryption: Shows the encryption method that access point or wireless device uses. If the wireless access point does not enable encryption, you’ll see ‘None’ displayed here. Authentication: Shows the authenti cation mode that access point or wireless device uses. If ...

  • Kraun KR.PP - page 18

    If the access point you selected does not enable encryption (The content of ‘Encryption’ field of the access point you selected is ‘None’, you’ll be connected to this wirele ss access point within one minute. Please jump to step 6. If the access point you selected enab les encryption, please proceed to next step. 4. If the wireless access ...

  • Kraun KR.PP - page 19

    5. If the wireless access point uses encryption, you have to input WEP passphrase or WP A preshared key . Please ask the owner of the wireless access point you want to connect, and input the correct passphrase / preshared key here, then click ‘OK’. If the value you inputted here is wrong, you will not be able to connect to this wireless access ...

  • Kraun KR.PP - page 20

    6. Y ou’ll see ‘Connected <-> SSID’ (‘SSID’ is the SSID of the wireless access point or wireless device you connected to) message displayed at lower -left corner of configura tion utility , congratulations, you’re successfully connected to the ac cess point or wireless device you selected! 7. Y ou can put the mouse cursor over the ...

  • Kraun KR.PP - page 21

    2-2-2 Using W indows Zero Configuration W indows XP and V ista has a built-in wireless network configuration utility , called as ‘W indows Zero Confi guration’ (WZC). Y ou can also use WZC to configure your wi reless network parameter: 1. Right-click Ralink configuration utili ty icon and select ‘Use Zero Configuration as Configuration utilit ...

  • Kraun KR.PP - page 22

    4. Right-click ‘W ireless Network Connec tion’ (it may have a number as suff ix if you have more than one wireless network car d, please make sure you right-click the ‘Ralink 802. 1 1n W ireless LAN Card), then select ‘V iew A v ailable W ireless Networks’. 5. All wireless access points in proxim ity will be displayed here. If the access ...

  • Kraun KR.PP - page 23

    6. If the access point is protected by encryption, you have to input its security key or passphrase here. It must match the encryption setting on the access point. If the access point you selected doe s not use encryption, you’ll not be prompted for security key or passphrase. ...

  • Kraun KR.PP - page 24

    7. If you can see ‘Connected’ message, the connection between your computer and wireless access point is successfully established. ...

  • Kraun KR.PP - page 25

    2-3 Connection Profile Management If you need to connect to different wireless access points at dif ferent time, like of access point of your home, of fice, cybercafe, or public wireless service, you can store the connection parameters (encryption, passphrase, security etc, etc.) as a profile for every access point, so you don’ t have in input th ...

  • Kraun KR.PP - page 26

    Or , you can add a connected wirele ss access point or wireless device to a profile by clicking ‘Site Survey’ tab, then click ‘Add to Profile’ button: ...

  • Kraun KR.PP - page 27

    And you can set the parameter for this connection here: ...

  • Kraun KR.PP - page 28

    Here are descriptions of every setup items: Pr ofile Name Please give this pr ofile a name, up to32 alphanumerical characters and symbols ar e allowed, but space is not allowed. SSID The SSID of the wir eless access point or wir eless device you selected will be displayed her e. But if the SSID of access point or wir eless device is not available, ...

  • Kraun KR.PP - page 29

    RTS Thr eshold Check the box and you can set RTS thr eshold manually her e. Do not mod ify default setting unless you know what it is. Fragment Check the box and you can set fragment thr eshold Thr eshold manually her e. Do no t modify default setting unless you know what it is. Now click ‘Authentication and Secur ity’ tab, and set the encrypti ...

  • Kraun KR.PP - page 30

    automatically , and please do not modify it. If you select ‘LEAP’, the following message will be displayed. Please input LEAP identity , passwor d, domain name, and select en cryption type. Y ou can check ‘Show Passwor d’ box so the passwor d you inputted will be displayed as you type, but not r eplace by asterisk. Encryption: Select the en ...

  • Kraun KR.PP - page 31

    this field will be disabled and grayed out. WEP Key Y ou can select key ty pe (Hex or ASCII) and input WEP key her e. If encryption is not enabled, or you select ‘WP A ’ as en cryption type, this field will be disabled and grayed out. Show Passwor d Check this box and all passphrases or security keys you inputted will be displa yed as you type, ...

  • Kraun KR.PP - page 32

    Select the profile you wish to use, a nd click ‘Activate’ to use the profile you selected. Y ou can only activate a pr ofile a time, and the profile which is activated currently w ill have a green check ( ) before its name. If the wireless access point is not reachable, a red check ( ) will be displayed before its name. If you want to change th ...

  • Kraun KR.PP - page 33

    2-3-2 Using 802.1x – Certification After you click ‘802.1x Setting’ , a new window will appear: Here are descriptions of every setup items: Authentication Please select an 802.1x authentication type her e. T ype The type you select her e must be identical to the type of the 802.1x authentication type you’r e using. Session Y ou can enable o ...

  • Kraun KR.PP - page 34

    Domain Name Please input the domain name of 802.1x authentication her e. This field will be grayed out when authentication type is not ‘EAP-F AST’. Use Client If the authenticati on type you use is ‘PEAP’ or ‘TTLS’, you can use the certificate stor ed on your computer . If the authentication type you use is ‘TLS/Smart Car d’, this b ...

  • Kraun KR.PP - page 35

    Passwor d Please input the passw or d of tunneled authentication (of tunneled her e. authentication) Passwor d Mode Please select th e passwor d mode of ‘EAP-F AST’ authentication mode. This setting is hidde n when the authentication type is not ‘EAP-F AST’. After you finish all settings, click ‘OK’ to save settings and exit. ...

  • Kraun KR.PP - page 36

    2-3-3 Using 802.1x - CA Server If you want to use CA server , pleas e click ‘CA Server ’ tab. And the following message will be displayed: Here are descriptions of every setup items: Use certificate Check this box to en able the use of certificate chain. chain Certificate Please select the issuer of certificate fr om this Issuer dr opdown menu. ...

  • Kraun KR.PP - page 37

    2-4 V iew Network Statistics and Link S tatus The configuration utility provides information a bout network statistics and link status. If you want to know how your wireless network card works, you can use these functions to get detailed information about the wireless connection you’re using. 2-4-1 Network Stati stics Please follow the following ...

  • Kraun KR.PP - page 38

    All connection-related sta tistics is displayed here. Y ou can click ‘Reset Counter ’ to reset the statistic s of all items back to 0. Click ‘OK’ to close the window . ...

  • Kraun KR.PP - page 39

    2-4-2 Link Status Please follow the following instructions to check network statistics: 1. Right-click the Ralink configuration u tility icon located at lower -right corner of computer desktop, then click ‘Launch Config Utilities’. 2. Click ‘Link Status’ tab, and information about current wireless connection will be displayed: ...

  • Kraun KR.PP - page 40

    These information displayed here are updated every second, and here are descriptions of every item: S tatus Display the SSID and BSSID of connected wir eless access point or wir eless d evice (displayed as SSID <-> BSSID as shown in above pictur e. If ther e’ s no active connection curr ently , ‘Disconnected’ will be displayed her e. Ex ...

  • Kraun KR.PP - page 41

    Noise Level Displays the per centage or level of noise (unusable) signal. If the value of this item is high, data transfer rate will dr op. dBm Check this box and the value of signal str ength and noise level will be displayed in dBm level instead of per centage. There are several wireless statuses ava ilable at the bottom of this window . For thei ...

  • Kraun KR.PP - page 42

    2-5 Advanced Settings This wireless network card provide s several advanced settings for experienced wireless users. Y ou can chan ge these settings to increas e data transfer performance, or change operation mode. Please follow the following instructions to set advanced wireless settings: 1. Right-click the Ralink configuration u tility icon locat ...

  • Kraun KR.PP - page 43

    Here are descriptions of every setup items: W ir eless mode Select wir eless ope ration mode, available options ar e 802.1 1 B/G mix, 802.1 1 B only , and 802.1 1 B/G/N mix. Y ou can select 802.1 1 B/G/N mix to maximize wir eless compatibility with wir eless access points and other wir eless devices. Anyway , you can set this setting to ‘802.1 1 ...

  • Kraun KR.PP - page 44

    when this wir eless network car d should switch to another wir eless access point with better signal quality . Only adjust value when you understand what it means. T urn of f RF Click this button to switch wireless radio of f, click it again switch wir eless radio on. Select Y o ur Select the country / r egion code of the place you’r e Country Re ...

  • Kraun KR.PP - page 45

    Non-Serving When you’r e c onnecting to CCX-compatible Channel access point, check this box to enable measur ement Measur ements on unused radio channels to impr ove wir eless connectivity . Limit --- Limit the time used for said measur ement to a milliseconds certain time. Default value is 250. After you finish the settings, click ‘Apply’ to ...

  • Kraun KR.PP - page 46

    2-6 QoS Setting This wireless network card provides Qo S (Quality of Service) function, which can improve the performance of certain network applications, like audio / video streaming, network te lephony (V oIP), and others. When you enable WMM (W i-Fi MultiMedia) function of this network card, you can define the priority of different kinds of data ...

  • Kraun KR.PP - page 47

    Here are descriptions of every setup items: WMM Enable Check this box to enable WMM function. Please click ‘Apply’ button on the right of this check box after you check or uncheck this box, so corr esponding settings in this window will be activated or deactivated r espectively . WMM - Power Enable WMM power saving mode to save ener gy Save Ena ...

  • Kraun KR.PP - page 48

    Effort), AC_VI (V ideo First), and AC_V O (V oice First). Dir ect Link Enable or disable dir ect link setup (DLS) function. Setup Enable This function will gr eatly impr ove the data transfer rate between WMM-enabled wir eless devices. Please click ‘Apply’ button on the right of this check box after you check or uncheck this box, so corr espond ...

  • Kraun KR.PP - page 49

    2-7 WPS Configuration W i-Fi Protected Setup (WPS) is the latest wireless network technology which makes wireless network setup become very si mple. If you have WPS-enabled wireless access point, and you want to establish a secure connection to it, you don’t have to c onfigure the wireless access point and setup data encryption. All you have to d ...

  • Kraun KR.PP - page 50

    2-7-1 WPS Setup - PBC (Push -Button Configuration) 1. Right-click the Ralink configuration utility icon located at lower-right corner of computer desktop, then click ‘Launch Config Utilities’. 2. Click ‘WPS Configura tion’ tab, and the follo wing settings will appear: ...

  • Kraun KR.PP - page 51

    3. Push the ‘WPS’ button on your wireless access point (the button used to activate WPS standby m ode may have another name), or use other way to start WPS standby mode as th e instruction given by your wireless access point’ s user manual. 4. Before you start to establish th e wireless connection by using WPS, you can click ‘Rescan’ butt ...

  • Kraun KR.PP - page 52

    WPS, and please be patient (This ma y require several seconds to one minute to complete). When you see ‘WPS status is connected successfully’ message, means the connection between your wireless network card and access point is successfully connected by WPS, and the information about access point you c onnected to will be displayed. ...

  • Kraun KR.PP - page 53

    Sometime WPS may fail, and you can click ‘PBC’ button few more times to try again. When an access po int is connected, you can click ‘Disconnect’ to disconnect your wi reless network card from a connected access point, or select another WPS-ena bled wireless access point, then click ‘Connect’ to establish connection to selected access p ...

  • Kraun KR.PP - page 54

    2-7-2 WPS Setup - PIN If the wireless access point you wish to connect supports PIN, please follow the following instructions to establish connection to it: 1. Right-click the Ralink configuration utility icon located at lower-right corner of computer desktop, then click ‘Launch Config Utilities’. 2. Click ‘WPS Configura tion’ tab, and the ...

  • Kraun KR.PP - page 55

    The PIN number of your wireless network card is an eight-dig it number located at the upper -right position of configuration utility . Remember it, and input the number to your wireless access point as the WPS PIN code (Please refer to the user manual of your wireless access point for instructions about how to do this). 3. Click ‘PIN’ button no ...

  • Kraun KR.PP - page 56

    2-8 About The ‘About’ tab provides you the info rmation about version numbers of configuration utility , firmware, and other important information about your wireless network card. Please follow the following instructions to see these information: 1. Right-click the Ralink configuration u tility icon located at lower -right corner of computer d ...

  • Kraun KR.PP - page 57

    If you need assistance about network problem, you’ll need these values. Y ou can al so click ‘WWW .RALINKTECH.COM’ button to go to the web site of network card driver manufact urer and get more information about your wireless network card. Please click ‘OK’ to close configuration utility . ...

  • Kraun KR.PP - page 58

    CHAPTER III: Soft-AP Function Excepting become a wireless client of other wireless access points, this wireless card can act as a wireless service provider also! Y ou can switch this wireless card’ s operating mode to ‘AP’ mode to simulate the function of a real wireless access point by so ftware, and all other computers and wireless devices ...

  • Kraun KR.PP - page 59

    A configuration window will appear after you switch the operation mode to ‘AP’ or click ‘Launch Config Utilities’ after you right-click the Ralink configuration utility , which asks you to assign an existing network card with internet connection: If your computer has another network car d which is connected to Internet, please select it fro ...

  • Kraun KR.PP - page 60

    Here are descriptions of every setup items: SSID Please input the SSI D (the name used to identify this wir eless access point) her e. Up to 32 numerical characters can be accepte d her e, excepting space. TX Rate Please select the data transfer rate her e. The maximum TX rate you can select her e depends on the wir eless mode yo u’r e using. It? ...

  • Kraun KR.PP - page 61

    Channel Please select the wir e less channel you wish to use. The number of channels available her e will vary depends on the setting of ‘Country Region Code’. W ir eless Mode Please select th e wir eless operating mode. Y ou can limit the type of wir eless client to 802.1 1b or 802.1 1g only , or allow 802.1 1b/g, and 802.1 1b/g/n clients. It? ...

  • Kraun KR.PP - page 62

    select ‘Auto’ to let configuration utility to decide to use wir eless pr otection or not. Y ou can also select ‘ON’ or ‘OFF’ to for ce the use of wir eless pr otection or not. Beacon(ms) Y ou can define the time interval that a beacon signal should be send. Default value is 100. Do not modify this value unless you know what will be affe ...

  • Kraun KR.PP - page 63

    3-2 Security Settings This wireless card supports wireless encryption in AP mode, which will encrypt the data being transferred ove r the air to enhance data security level. It’ s recommended to enable data encryption unless you wish to open your computer (and its internet connection) to the public. When you click ‘Security Setting’ in Ralink ...

  • Kraun KR.PP - page 64

    Encryption Please select an encryption mode. The available T ype options in this settin g item will vary depending on the authentication type you se lect. If you select ‘Not Use’, data will not be encrypted and people with some networking knowledge will be able to r ead the data you transfer with pr oper tool. NOTE: WP A encryption is safer tha ...

  • Kraun KR.PP - page 65

    bits, but the data transfer speed will be slightly r educed. Show Passwor d Check this box and the WP A pr e-shar ed key orWEP key you inputted will be shown, but not r eplaced by asterisk (*). OK Click this button to save changes you made in this page. Cancel Click this button to di scar d all changes you made in this window . ...

  • Kraun KR.PP - page 66

    3-3 Access Control If you’re not going to open your comput er and wireless resources to the public, you can use MAC address f iltering function to enforce your access control policy , so only wire less clients with MAC address you defined by this function can be conn ected to your software access point. Please follow the following instructi ons t ...

  • Kraun KR.PP - page 67

    Here are descriptions of every setup items: Access Policy Select the policy type of your access rule: Disable: Allow any wir eless client with pr oper authentication settings to connect to this access point. Allow All: Only allow wi r eless clients with MAC addr ess listed her e to connect to this access point. Reject All: Reject wir ele ss clients ...

  • Kraun KR.PP - page 68

    MAC addr ess Input the MAC addr ess of the wir eless client you you wish to allow or r eject her e. No colon (:) or hyphen (-) r equir ed. Add Add the MAC addr ess you inputted in ‘MAC addr ess’ field to the list. Delete Please select a MAC addr ess fr om the list, then click ‘Delete’ button to r emove it. Remove All Delete all MAC addr ess ...

  • Kraun KR.PP - page 69

    3-4 Connection table If you want to see the list of all wire less clients connected to this access point, please follow the following instructions: 1. Right-Click Ralink configuration utility icon, and select ‘Launch Config Utilities’ 2. Click ‘Mac T able’ tab, and a list containing all connected wireless clients will appear: ...

  • Kraun KR.PP - page 70

    Here are descriptions of every fields: MAC Addr ess Displays the MAC addr ess of this wir eless client. AID The serial number of this wir eless connection. Power Saving Displays the capability of power-saving function of Mode this wir eless client. S tatus Displays additional information of this wir eless Connection, like curr ent wir eless operati ...

  • Kraun KR.PP - page 71

    3-5 Event Log This software access point will log all wireless-related activ ities as a log. Y ou can follow the following instructions to view the content of the event log: 1. Right-Click Ralink configuration utility icon, and select ‘Launch Config Utilities’ 2. Click ‘Event Log’ tab, and the event log will be displayed: Y ou can click ‘ ...

  • Kraun KR.PP - page 72

    3-6 Statist ics If you want to know detailed informati on about how your software access point works, you can follow the follo wing instructions to view the statistics of the access point: 1. Right-Click Ralink configuration utility icon, and select ‘Launch Config Utilities’ 2. Click ‘Statistics’ tab, and th e event log will be displayed: Y ...

  • Kraun KR.PP - page 73

    CHAPTER IV : APPENDIX 4-1 Hardware Specification Standards: IEEE 802.11b/g/Draft-N Interface: 32-bit CardBus (PCMCIA Interface) Frequency Band: 2.4000 ~ 2.4835GHz (Industr ial Scientific Medical Band) Data Rate: 11b: 1/2/5.5/11Mbps 11g: 6/9/12/24/36/48/54Mbps 11n (20MHz): MCS0-15, 32 with Half Guard Interval Support (up to 144Mbps) 11n (40MHz): MCS ...

  • Kraun KR.PP - page 74

    4-2 T roubleshooting If you encounter any problem when you’ re using this wireless network card, don’t panic! Before you call your d ealer of purchase for help, please check this troubleshooting table, the solution of your problem could be very simple, and you can so lve the problem by yourself! Scenario Solution I can’t find any wireless acc ...

  • Kraun KR.PP - page 75

    ‘SSID’ field in ‘Site Survey’ function), you have to input correct SSID of the access point you wish to connect. Please contact the owner of access point to ask for correct SSID. 3. Y ou have to input correct passphrase / security key to connect an access point with encryption. Please contact the owner of access point to ask for correct pas ...

  • Kraun KR.PP - page 76

    4-3 Glossary 1. What is the IEEE 802.1 1g standard? 802.1 1g is the new IEEE standard for high-speed wireless LAN communications that provides for up to 54 Mbps data rate in the 2.4 GHz band. 802.1 1g is quickly b ecoming the next mainstream wireless LAN technology for the home , of fice and public networks. 802.1 1g defines the use of the sa me OF ...

  • Kraun KR.PP - page 77

    5. What is Infrastructur e? An integrated wireless and wire less and wired LAN is called an Infrastructure configuration. Infrastru cture is applicable to enterprise scale for wireless access to central database, or wireless application for mobile workers. 6. What is BSS ID? A specific Ad hoc LAN is cal led a Basic Service Set (BSS). Computers in a ...

  • Kraun KR.PP - page 78

    12. What is DSSS? What is FHSS? And what are their differ ences? Frequency-hopping spread-spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver . Properly sync hronized, the net effect is to maintain a single logical channel. T o an unintended receiver , F HSS appears to be shor ...

  • Kraun KR.PP - page 79

    15. What is WMM Pow er Save? WMM Power Save is a set of features for W i-Fi networks that increase the efficiency and flexibility of data transmission in order to conserve power . WMM Power Save has been optimized for mobile devices running latency-sensitive a pplications such as voice, audio, or video, but can benefit any W i-Fi device. WMM Power ...

  • Kraun KR.PP - page 80

    4-4 FCC and Other Compliance S tatements Federal Communication Commission Interference S t atement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. T ...

  • Kraun KR.PP - page 81

    Federal Communication Commissi on (FCC) Radiation Exposure Statement This equipment complies with FCC r adiation exposure se t forth for an uncontrolled environment. In order to avoi d the possibility of exceeding the FCC radio frequency exposure limits, hum an proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. ...

  • Kraun KR.PP - page 82

    EU Countries Not intended for use None. ...

Manufacturer Kraun Category Network card

Documents that we receive from a manufacturer of a Kraun KR.PP can be divided into several groups. They are, among others:
- Kraun technical drawings
- KR.PP manuals
- Kraun product data sheets
- information booklets
- or energy labels Kraun KR.PP
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kraun KR.PP.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kraun KR.PP, service manual, brief instructions and user manuals Kraun KR.PP. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kraun KR.PP.

Similar manuals

A complete manual for the device Kraun KR.PP, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kraun KR.PP by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kraun KR.PP.

A complete Kraun manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kraun KR.PP - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kraun KR.PP, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kraun KR.PP, that we can find in the current document
3. Tips how to use the basic functions of the device Kraun KR.PP - which should help us in our first steps of using Kraun KR.PP
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kraun KR.PP
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kraun KR.PP in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kraun KR.PP?

Use the form below

If you did not solve your problem by using a manual Kraun KR.PP, ask a question using the form below. If a user had a similar problem with Kraun KR.PP it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)