English dropdown-ico

Manual Pelco c2485m-a-ml

28 pages 1.2 mb
Download

Go to site of 28

Summary
  • Pelco c2485m-a-ml - page 1

    INST ALLA TION Pressurized Spectra III ™ Series Fiber Optic Models English Español Português Italiano Français Deutsch C2485M-A-ML (2/05) ...

  • Pelco c2485m-a-ml - page 2

    ...

  • Pelco c2485m-a-ml - page 3

    C2485M-A-ML (2/05) 3 E ng li s h E spa ñ o l P or t ugu ê s It a li ano F rança i s D eu t sc h NOTE: This manual is designed to be a reference tool for the installation of your system. For best results and ease of installation, the dome system should be assembled, pressurized, and tested before installation. A Pressurized Spectra III cable harn ...

  • Pelco c2485m-a-ml - page 4

    4 C2485M-A-ML (2/05) Preinstallation English 1 Install the fiber optic module: Open the hinged door to the back box by pushing the tab lock towards the wall of the unit and lifting the door open. Remove the plug from the 16-pin connector . Install the module in the 16-pin connector . Secure the module to the circuit board standoff using the screw ...

  • Pelco c2485m-a-ml - page 5

    C2485M-A-ML (2/05) 5 English 5 Install the dome drive: a. Set the DIP switches located on the side of the dome drive. Refer to the labels located on the top of the dome drive or to the Quick Start Guide shipped with the dome drive. b. Line up the blue (A) and red (B) tabs with the blue (A) and red (B) labels. c. Push in on the tabs. Insert one side ...

  • Pelco c2485m-a-ml - page 6

    6 C2485M-A-ML (2/05) Site Installation English 1 Feed a fiber optic cable (not supplied) and the supplied wiring harness into the front of the mount and out the back of the mount. Connect the wires as required. Refer to T ables A, B, and C for cable and wiring information. Fasten the mount to the mounting surface. Refer to the instructions supplie ...

  • Pelco c2485m-a-ml - page 7

    C2485M-A-ML (2/05) 7 E ng li s h NOTE: These are the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.) NOTE: Input power for the dome is 24 V AC only. Power consumption is 75 V A per dome. Use a 24 V AC trans ...

  • Pelco c2485m-a-ml - page 8

    8 C2485M-A-ML (2/05) Preinstalación Español 1 Instale el módulo de fibra óptica: Abra la portezuela abisagrada de la caja posterior , para lo que deberá oprimir la ficha de cierre hacia la pared de la unidad y levantar la portezuela hasta que quede abierta. Quite el enchufe del conector de 16 patillas. Instale el módulo en el conector de 16 ...

  • Pelco c2485m-a-ml - page 9

    C2485M-A-ML (2/05) 9 Español 5 Instale la unidad del domo: a. Configure las posiciones de los conmutadores DIP ubicados en el lateral de la unidad del domo. Consulte las etiquetas ubicadas en la parte superior de la unidad del domo, o bien la Guía de inicio rápido enviada junto con la unidad del domo. b. Coloque en línea las fichas azul (A) y ...

  • Pelco c2485m-a-ml - page 10

    10 C2485M-A-ML (2/05) Instalación en la ubicación Español 1 Sitúe un cable de fibra óptica (no suministrado) y el arnés de cableado suministrado desde el frente de la montura y desde atrás de la parte posterior de la montura. Conecte los cables según se requiera. Consulte las T ablas A, B y C para obtener información sobre el cableado. Aj ...

  • Pelco c2485m-a-ml - page 11

    C2485M-A-ML (2/05) 11 E spa ñ o l NOT A: Las siguientes son las distancias máximas recomendadas para las aplicaciones que funcionan a 24 VCA y están calculadas en base a una caída de voltaje del 10 por ciento (El diez por ciento es generalmente la caída máxima de tensión permitida para los dispositivos que funcionan con energía de CA.) NOT ...

  • Pelco c2485m-a-ml - page 12

    12 C2485M-A-ML (2/05) Pré-instalação Português 1 Instale o módulo de fibra óptica: abra a porta da back box com dobradiça, empurrando a trava da aba na direção da parede da unidade e levantando a porta para abri-la. Remova o plugue do conector de 16 pinos. Instale o módulo no conector de 16 pinos. Fixe o módulo na isolador da placa de c ...

  • Pelco c2485m-a-ml - page 13

    C2485M-A-ML (2/05) 13 Português 5 Instale o dome drive: a. Ajuste as chaves DIP localizadas na lateral do dome drive. Consulte os rótulos na parte superior do dome drive, ou o Guia de Início Rápido fornecido com o dome drive. b. Alinhe as abas azul (A) e vermelha (B) com os rótulos azul (A) e vermelho (B). c. Empurre as abas para dentro. Insir ...

  • Pelco c2485m-a-ml - page 14

    14 C2485M-A-ML (2/05) Instalação no local Português 1 Conecte o cabo de fibra óptica (fornecido) e o módulo de ligação fornecido na entrada da parte frontal do suporte e na saída da parte posterior do suporte. Conecte os cabos conforme necessário. Consulte as T abelas A, B e C para obter informações sobre os cabos e ligações. Fixe o s ...

  • Pelco c2485m-a-ml - page 15

    C2485M-A-ML (2/05) 15 P or t ugu ê s OBSERV AÇÃO: Estas são as distâncias máximas recomendadas para aplicações em 24 VCA, e estão calculadas com uma queda de tensão de 10%. (10% é geralmente o máximo permitido de queda de tensão para dispositivos alimentados por CA). OBSERV AÇÃO: A entrada de força para o dome é somente de 24 VCA. ...

  • Pelco c2485m-a-ml - page 16

    16 C2485M-A-ML (2/05) Pre-installazione Italiano . 1 Installare il modulo a fibre ottiche. Aprire lo sportello cardinato verso il contenitore spingendo l'aletta di bloccaggio verso la parete dell'unità e sollevando lo sportello aperto. T ogliere la spina dal connettore a 16 pin. Installare il modulo nel connettore a 16 pin. Fissare il m ...

  • Pelco c2485m-a-ml - page 17

    C2485M-A-ML (2/05) 17 Italiano 5 Installare l'unità dome: a. Impostare gli interruttori DIP situati di lato all'unità dome. Consultare le etichette situate sulla sommità dell'unità dome, oppure la Guida di consultazione rapida in dotazione all'unità stessa. b. Allineare le linguette blu (A) e rossa (B) con le etichette blu ...

  • Pelco c2485m-a-ml - page 18

    18 C2485M-A-ML (2/05) Installazione in loco Italiano 1 Infilare il cavo a fibre ottiche (non in dotazione) ed il cablaggio in dotazione nella parte anteriore della staffa e fuori dalla parte posteriore. Collegare i fili secondo necessità. Consultare le T abelle A, B e C per informazioni sui cavi. Fissare la staffa alla superficie di montaggio. ...

  • Pelco c2485m-a-ml - page 19

    C2485M-A-ML (2/05) 19 It a li ano NOT A: i dati seguenti indicano le distanze di collegamento massime per applicazioni a 24 V c.a. e sono calcolate con una caduta di tensione del 10% (10% è di solito la caduta di tensione massima consentita per dispositivi alimentati in c.a.). NOT A: l'alimentazione di ingresso per il dome è solo di 24 V c.a ...

  • Pelco c2485m-a-ml - page 20

    20 C2485M-A-ML (2/05) Pré-installation Français 1 Installez le module à fibres optiques : Ouvrez la porte à charnière de l'embase en poussant la languette de sûreté vers la paroi de l'unité, puis en soulevant la porte pour l'ouvrir . Retirez le bouchon du connecteur à 16 broches. Installez le module dans le connecteur à 16 ...

  • Pelco c2485m-a-ml - page 21

    C2485M-A-ML (2/05) 21 Français 5 Installez la commande de dôme : a. Réglez les commutateurs DIP situés sur le côté de la commande de dôme. Reportez-vous aux étiquettes situées en haut de la commande de dôme ou au guide de démarrage rapide joint à la commande de dôme. b. Alignez les languettes bleue (A) et rouge (B) sur les étiquettes ...

  • Pelco c2485m-a-ml - page 22

    22 C2485M-A-ML (2/05) Installation sur place Français 1 Faites passer un câble à fibres optiques (non fourni) et le faisceau de câbles fourni par l'avant de la fixation et faites-le sortir par l'arrière de celle-ci. Connectez les fils selon le nécessaire. Reportez-vous aux tableaux A, B et C pour les câbles et les fils. Attache ...

  • Pelco c2485m-a-ml - page 23

    C2485M-A-ML (2/05) 23 F rança i s REMARQUE : Ces valeurs sont les distances maximales recommandées pour les applications 24 Vca ; elles sont calculées avec une chute de tension de 10 %. (Une chute de tension de 10 % est généralement la valeur maximale autorisée pour les dispositifs alimentés en courant alternatif.) REMARQUE : L'alimenta ...

  • Pelco c2485m-a-ml - page 24

    24 C2485M-A-ML (2/05) V orinstallation Deutsch 1 Installieren Sie das Faseroptikmodul: Öffnen Sie die mit Scharnieren versehene Klappe der Back-Box, indem Sie die V erriegelung zur Gehäusewand schieben und die Klappe heben. Entfernen Sie die V erschlusskappe vom 16-Stift-Anschluss. Schließen Sie das Modul an den 16-Stift-Anschluss an. Befestigen ...

  • Pelco c2485m-a-ml - page 25

    C2485M-A-ML (2/05) 25 Deutsch 5 Installieren Sie den Dome-Antrieb: a. Stellen Sie die DIP-Schalter seitlich am Dome-Antrieb ein (siehe Etikette auf der Oberseite des Dome-Antriebs oder Kurzanleitung, die im Lieferumfang enthalten ist). b. Richten Sie die blauen (A) und roten (B) Laschen mit den blauen (A) und roten (B) Etiketten aus. c. Drücken Si ...

  • Pelco c2485m-a-ml - page 26

    26 C2485M-A-ML (2/05) Installation vor Ort Deutsch 1 Schieben Sie ein Faseroptikkabel (nicht im Lieferumfang enthalten) und den mitgelieferten Kabelsatz vorne in die Halterung und hinten aus der Halterung. Schließen Sie die Kabel an. In den T abellen A, B und C finden Sie V erkabelungsinformationen. Bringen Sie die Halterung auf der Montageober? ...

  • Pelco c2485m-a-ml - page 27

    C2485M-A-ML (2/05) 27 D eu t sc h HINWEIS: Dies sind die empfohlenen maximalen Entfernungen für 24-V-WS-Anwendungen, wobei ein zehnprozentiger Spannungsabfall einberechnet ist. (10 Prozent ist im Normalfall der maximal zulässige Spannungsabfall für wechselstrombetriebene Geräte.) HINWEIS: Die Eingangsleistung für den Dome beträgt nur 24 V WS. ...

  • Pelco c2485m-a-ml - page 28

    Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...

Manufacturer Pelco Category Security Camera

Documents that we receive from a manufacturer of a Pelco c2485m-a-ml can be divided into several groups. They are, among others:
- Pelco technical drawings
- c2485m-a-ml manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco c2485m-a-ml
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco c2485m-a-ml.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco c2485m-a-ml, service manual, brief instructions and user manuals Pelco c2485m-a-ml. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco c2485m-a-ml.

Similar manuals

A complete manual for the device Pelco c2485m-a-ml, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco c2485m-a-ml by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco c2485m-a-ml.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco c2485m-a-ml - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco c2485m-a-ml, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco c2485m-a-ml, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco c2485m-a-ml - which should help us in our first steps of using Pelco c2485m-a-ml
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco c2485m-a-ml
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco c2485m-a-ml in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco c2485m-a-ml?

Use the form below

If you did not solve your problem by using a manual Pelco c2485m-a-ml, ask a question using the form below. If a user had a similar problem with Pelco c2485m-a-ml it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)