-
Hoover S1211 - page 1
EliteTM Sup Dual Purpose Vacuum Cleaner R Review this manual before 0 erating P c eaner ...
-
Hoover S1211 - page 2
during assembly or operation, call 1-8OWM4-9200 for an automated referral of authorized service outlet locations (U.S. only) or l-216-499-9499 to speak with a representative in our Consumer Response Center. DO NOT RETURN THIS PRODUCT TO THE STORE. Fill in and retain This vacuum cleaner is a combination cleaner. It is designed for carpet and rug cle ...
-
Hoover S1211 - page 3
Important Safeguards! When using an electrical appliance, always follow basic precautions, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE Warning. injury: w To reduce the risk of fire, electric shock, or . l . . . . . l . . . . . @ . l l Do not use outdoors or on wet surfaces. Close supervision is necessary when any appl ...
-
Hoover S1211 - page 4
mbling cleaner s extremely importamt to read and if Uow a01 the instruction steps in order. The assembled cleaner will look like this drawing. If you need assistance with any step of the assembly, call 1-800-944-9204) for an automated referral of authorized service outlet locations (U.S. only) or l-216-499-9499 to speak with a representative in our ...
-
Hoover S1211 - page 5
LOWER HANDLE Place upper and lower handle sections on a flat surface with cord hooks on top. With hands on sides of handle sections, push sections together firmly until they “click” into place (Fig. 1). *Be careful not to press against the rod extending from the lower handle. (Fig. 2) If the rod breaks or bends, the cleaner will not work proper ...
-
Hoover S1211 - page 6
I I Rotate cord protector on cord until you see its arrow. (Fig. 4) - ,---, ARROW&- CoRD p ROTECTOR UPPER HANDLE With arrow on cord protector pointing toward arrow on upper handle, press groove in cord protector into slot in upper handle. (Fig. 5 and 6) Pull cord tight. PROTECTOR Press cord into place at each of the three notches indicated. (Fi ...
-
Hoover S1211 - page 7
RAILS RAILS Note location of tapered rails on bracket and on lower handle. (Fig. 8) With printed side of bracket facing up, slide rails on bracket onto rails on lower handle until bracket snaps past the lock tab. (Fig. 9) Pull bracket toward bottom of handle slightly to make sure bracket is locked in place. Make sure hole in bracket aligns with hol ...
-
Hoover S1211 - page 8
I I I Hook tool rack over left edge of ‘handle, matching arrows and letters. (Fig. 11) With cord hooks to the back, place assembled handle onto handle base of cleaner body. (Fig. 13) Rock handle side to side while pushing down firmly. Extra pushing effort may be required. Push bolt into hole on lower front of handle. (Fig. 14) If bolt will not ...
-
Hoover S1211 - page 9
1 BAG COMiik l’MENT hLOTS ’ DIRT TUBE Place nut in recessed area at back of handle. Hold nut in place while tightening bolt securely with a screwdriver. (Fig. 15) Note: Only one r&t is needed on this model. The extra nut is not required but has been provided for your convenience. Pull bag door latch forward and remove door. Set bag door asi ...
-
Hoover S1211 - page 10
Align opening in paper bag with dirt tube inside bag compart- ment. (Fig. 19) Push bag collar firmly onto dirt tube. (Fig. 20) Tuck top and bottom of bag into bag compartment. To replace bag door, insert the tabs on bottom of bag door into the slots on bag compartment. (Fig. 21) Make sure all edges of paper bag are completely inside the bag compart ...
-
Hoover S1211 - page 11
(some models only) Insert hose connector into side of rack. (Fig. 23) ST--- l Position wand in side of tool rack and snap into place. (Fig. 25) While wrapping hose in a clockwise direction, push it firmly into rack at areas shown. (Fig. 24) Note: To keep hose secured, place rot nd end of hose below bottom extension. (Fig. 24, inset) J Snap dusting ...
-
Hoover S1211 - page 12
The assembled cleaner will look like the drawing below. L. 11 1. Handle 2. Cord hooks: wrap cord around hooks for storage. The top hook can be rotated right or left for easy cord release. 3. Bag door latch 4. ON/OFF switch: located on side of handle. 5. Bag door 6. Stair cleaning handle: located on lower edge of bag. 7. Handle release lever: step o ...
-
Hoover S1211 - page 13
w to use To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug ...
-
Hoover S1211 - page 14
Carpet hei adjustment The cleaning of carpet and rugs takes place at the nozzle. It is necessary to raise and lower the nozzle for various carpet pile heights by sliding the nozzle control knob to the correct setting. For ease in sliding knob, the handle should be in the upright position. The nozzle will not move Into the adjusted position until th ...
-
Hoover S1211 - page 15
The Hoover Company 101 East Maple Street North Canton, OH 44720 No. of Items Ordered: Please complete this entire form! a4010001A 0 160147AG 0 4010324A 0 049258AG 0 57363003 0 38528027 0 38528008 0 38634074 Please Print Your Name and Address carefully in Ink. Please allow 3 to 4 weeks for delivery. I Type A Disposable bags 4010001A 4010324A I Breat ...
-
Hoover S1211 - page 16
...
-
Hoover S1211 - page 17
Gleaming lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge. Before reaching edge, push down on handle. This will lift up the nozzle (front of cleaner) and will prevent rug from clinging to cleaner. Continue to lift up nozzle so that when you have reached the edge, it is completely off the rug. Move cleaner ...
-
Hoover S1211 - page 18
leaning to Some models come with tools; for others, tools are available at additional cost from your Autho- rized Hoover Dealer (Depot), a Hoover Factory Service Center or by writing to The Hoover Company, North Canton, Ohio 44720 The tool set includes a hose, wand, crevice tool, furniture nozzle and dusting brush. : A. Attach hose to cleaner Turn ...
-
Hoover S1211 - page 19
HOSE DOOR I and tools The tools are attached to the hose or the wand in the same manner. Push tool firmly onto hose; twist tool slightly to tighten or loosen connec- tion. Use cleaning tools with cleaner handle in upright position. Clearing obstructions To check for obstructions, first turn cleaner off and disconnect from electrical outlet; th ...
-
Hoover S1211 - page 20
The bag Whem to replace Check bag from time to time. It is recommended that you change the paper bag when dirt reaches the dotted line. If more dirt than this accumu- lates, your cleaner may not operate effectively. CAUTION: Very fine materials, such as face powder, cornstarch, fireplace ashes or fireplace soot, may seal the paper bag and may cause ...
-
Hoover S1211 - page 21
Note: not clean out old bag and reuse. Discard used bag. Align opening in new paper bag with dirt tube in outer bag. Push bag collar firmly onto dirt tube. Fold top of bag down under top of bag compartment. To replace bag door, lift up lower edge of paper bag. Insert the 3 tabs on bottom of bag door into the 3 slots on bag compartment. Make sure al ...
-
Hoover S1211 - page 22
2. Place handle in operating position and turn cleaner over. Insert end of flat screwdriver into one of the four slots beside an arrow on bottom of cleaner. 3. For slots nearest the rear wheels, push handle of screwdriver toward cleaner handle; for remain- ing two slots, pry outward to release latches. 4. Turn cleaner over and lift off hood. 5. Rem ...
-
Hoover S1211 - page 23
The belt on your HOOVER cleaner causes the agitator to rotate and is important for the effective operation of the cleaner. The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition. When to replace To check belt, remove bottom plate as shown in “How to replace belt.” Rep ...
-
Hoover S1211 - page 24
4. If belt is not broken, pull it off the motor pulley. 5. Return cleaner to bottom side up. Remove agitator and belt. 6. Slip agitator through new belt (with lettering toward outside of cleaner) and position belt in belt guide. Lower end of belt into opening in cleaner body; reposition agitator. 7. Place the three tabs on bottom plate into slots i ...
-
Hoover S1211 - page 25
8. Turn cleaner over and stretch new belt onto motor pulley. Extra effort may be required to stretch belt onto pulley. 9. Replace hood and nozzle control knob. The agitator When to replace Disconnect cleaner from electri- cal outlet. When agitator brushes are worn, the agitator should be replaced. To check condition of brushes, move edge of card ac ...
-
Hoover S1211 - page 26
If you have a proble This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem occurs, it usually can be solved quite easily when the cause is found. Therefore, this check list is provided for your convenience. Problem Possible cause Possible solution Cleaner won’t run I. ...
-
Hoover S1211 - page 27
To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: @ checking the Yellow Pages under “Vacuum Cleaners - Household” OR - 0 checking the list of Factory Service Centers provided with this cleaner OR - e calling l-800-944-9200 for an ...
-
Hoover S1211 - page 28
Full One Year Warranty (Domestic Use) Your HOOVER@ appliance is warranted in normal household use, in accordance with the Owner’s Manual against original defects in material and workmanship for a period of one full year from date of purchase. This warranty provides, at no cost to you, all labor and parts to place this appliance in correct operati ...
-
Hoover S1211 - page 29
26 ...
-
Hoover S1211 - page 30
Hoover and 0 (I are registered trademarks THE HOOVER COMPANY, NORTH CANTON, OHIO 44720 R6 3-95 MO35930/43-930/ 71-930/75-930 Litho USA 5651 l-396 ...
Do you have a question concerning Hoover S1211?
Use the form below
If you did not solve your problem by using a manual Hoover S1211, ask a question using the form below. If a user had a similar problem with Hoover S1211 it is likely that he will want to share the way to solve it.