English dropdown-ico

Manual Oki ML8810n

20 pages 1.82 mb
Download

Go to site of 20

Summary
  • Oki ML8810n - page 1

    1 The Cut Sheet Feeder (CSF) option can be mounted on the front or the rear of the printer , but can only be mounted on the rear if the optional Rear Push T ractor is not installed. The CSF stacker takes up to 100 sheets of 20-lb. (75 g/m 2 ) paper . Front View 1 Rear Sheet Supports 2 Paper Guides 3 Paper Set Lever 4 Center Guides 5 Guide Rolle r 6 ...

  • Oki ML8810n - page 2

    2 5. Plug the cable into the connect or on the left side of the printer . 6. Install the center guid es and rear sheet supports. Install the center guides by snapping them onto the round shaft (1), then securing the top hooks to the square shaft (2). Install th e rea r supports by sliding them onto the square shaft (2). The configuration y ou use ( ...

  • Oki ML8810n - page 3

    3 3. R emo ve the gear cove r (1). Push up on the tab (2), then twist it off . This provides access to the m o unting post (3). 4. R emove the stack er (1) and the stacke r support (2). K eep the stacker handy: you’ll need it later in the installation. Store the stacker support in case you ever decide to remo ve the rear push tr actor . 5. Slip t ...

  • Oki ML8810n - page 4

    4 For Narrow Paper: For Cards: 8. T urn on th e printe r . 9. Slide the stack e r (1) you remove d in Step 4 into the four guides (2) on the CSF . 10. Allum ez l'imprimante. Load Paper 1. R ea r Mount Only : Pull the stacker towa rd the front of the printer . 2. Mov e the paper lever to the RE SET position. 3. Unlock the lock lev ers (1). F6_2 ...

  • Oki ML8810n - page 5

    5 4. Adjust the position of the p aper guides (1) to fit the print media you are using, the n re-lock the levers. 5. F an and str aighten the print media, and pl ace it in the CSF . 6. Gently mo ve the paper lever to the SET position. 7. R ea r Mount Only : Push the stacker back. Select the Cut Sheet Feeder as the Default Paper Path 1. Press SEL to ...

  • Oki ML8810n - page 6

    6 Le dispositif d'alimenta tion de feuilles individ uelles (CSF) peut être monté à l'avant ou à l'arrière de l'imprimante, mais peut seulement être mont é à l'arrière si le chargeur à traction arrière n'est pas installé. L'empileuse CSF peut conte nir jusqu’à 100 feuilles de 75 g/m 2 (20-lb). Vue fr ...

  • Oki ML8810n - page 7

    7 5. Branchez le câble dans le connecteur du côté gauche de l'imprimante. 6. Installez les guides centraux et les supports de feuille arrière. Installez le s guides centraux en les enclenchant sur l'arbre rond (1), puis en fixant les crochets du haut sur l'arbre carré (2). Installez les supports arrière en les glissant sur l&ap ...

  • Oki ML8810n - page 8

    8 3. R etire z le couvercle d'engrenages (1). Poussez sur la languette (2) et tournez- le couv ercle. Cela donne accès au goujon de montage (3). 4. Enlevez l'empileuse (1) et le suppor t d'empileuse (2). Gardez l 'empileuse à portée de la mai n : V ous en aurez besoin plus tard lors de l'insta llation. Rangez le support ...

  • Oki ML8810n - page 9

    9 Pour du papier étroit Pour des cartes 8. Allumez l'imprimante. 9. Glissez l'empileuse (1) enlevé e à l'étape 4 sur les quatre guides (2) du CSF . 10. Allumez l'imprimante. Chargement du papier 1. Montage arrière seulement: Tirez l'empi leuse ve rs l'avant de l'imprimante. 2. Déplacez le levier de papier à ...

  • Oki ML8810n - page 10

    10 4. Réglez la position des guides-papier (1) pour correspondre au support utilisé, puis verrouillez à nouveau les leviers. 5. V entilez et redressez le supp ort d'impression et placez-le dans le dispositif d'alimentat ion. 6. Déplacez délicatement le levier de p apier à la position de réglage (SET). 7. Montage arri ère seule men ...

  • Oki ML8810n - page 11

    11 El opcional Cut Sheet Feeder [Alimentador de ho jas sueltas] (CSF) puede ser instalado en la parte delanter a o trasera de la impresor a, pero sólo puede instalarse en la parte tr asera si el R ear Push T ractor [T ractor de empuje tr asero] no está instalado. El Apilador CSF tiene ca pacidad par a 100 hojas de papel de 75 g/m² (20 lb.). Vist ...

  • Oki ML8810n - page 12

    12 5. Enchufe el cable en el conector en el costado izquierdo de la impresor a. 6. Instale las guías de centro y los soportes de hojas traseros. Instale las guías de centro haciendo que calcen en las vara redonda (1) y luego haciendo que calcen los ganchos supe riores en la var a cuadrada (2). Instale los soportes traseros deslizándolos en la va ...

  • Oki ML8810n - page 13

    13 3. R e tire la tapa del engranaje (1). Empuje la lengüeta (2) y luego gírela para retirarla. Esto le permite acceso a los pivotes de montaje (3). 4. R etire el apilador (1) y el soporte del apilador (2). Mantenga a mano el apilador: lo necesitará más adelante durante la instalación. Guarde el soporte del apilador en caso de que más adelant ...

  • Oki ML8810n - page 14

    14 Para papel estrecho Para tarjetas 8. Encienda la impresora. 9. Deslic e el apilador (1) que re tiró en el pa so 4, dentro de las cuatro guías (2) del CSF . 10. Encienda la impresora. Cargue papel 1. Montaje trasero únicamente: Hale el apilador hacia la parte delantera de la impresora. 2. Coloque la palanca del papel en la posición RESET . 3. ...

  • Oki ML8810n - page 15

    15 4. Ajuste la posición de las guías del papel (1) para que se ajusten al medio de impresión que es tá utilizando, y luego vuelva a cerr ar las pa lancas de cierre. 5. Abanique y enderece el medio de impresión y luego colóquelo en el CSF . 6. Muev a suavemente la palanca del pape l a la posición SET . 7. Montaje trasero únicamente: Empuje ...

  • Oki ML8810n - page 16

    16 O alimentador de folhas avul sas (CSF) opcional pode ser instalado na frente ou atrás da impressora, mas só pode ser instalado atrás se o tracionador de empurrar traseiro não estiver instalado . O empilhado r do alimen tador de fol has avulsas po de suportar um máxim o de 100 folhas de 80 g/m 2 (20 lb.) de papel norma l Vista fron tal 1 Sup ...

  • Oki ML8810n - page 17

    17 folhas avulsas da impressora. Solte com cuidado o empilhador até chegar à sua posição normal. 5. Ligue o cabo no conector no lado esquerdo da impressora. 6. Instale as guias centrais e os suportes traseiros das folhas. Instale as guias centrais encaixando-as no eixo redondo (1) e, em seguida, prendendo os ganchos superiores no eixo quadrado ...

  • Oki ML8810n - page 18

    18 Instalação: traseira Nota: ser montado na parte traseira da impressor a se o tracionador de empurr ar traseiro não estiver instalado. 1. Desembale o alimentador de folhas avulsas. Retire todos os materiais utilizados para transporte. 2. Desligue a impressora. 3. R etire a cobertura da engrenagem (1). Empurre a lingüeta (2) e retire-a. Isto p ...

  • Oki ML8810n - page 19

    19 Para papel largo Para papel estreito Para cartões 8. Li gue a impressor a. 9. Encaix e o empilhador (1) removido na etapa 4 nas quatro guias (2) no CSF 10. Ligue a impressora. Colocaçã o do papel 1. Apenas na instalação traseira: Puxe o empilhador no sentido da frente da impressora. 2. Mov a a alavanca de ajuste do papel para a posição RE ...

  • Oki ML8810n - page 20

    © 2006 Oki Data Americas, Inc. 20 59385401 3. Destra ve as alav ancas de tra vamento (1). 4. Ajuste a p osição das guias do papel (1) de acordo com o papel utilizado e, em seguida, trave nova mente as alavancas. 5. V entile e endireito o papel e coloq ue-o no CSF . 6. Mov a a alav anca de aj uste do papel c om cuida do para a posição SET . 7. ...

Manufacturer Oki Category Printer

Documents that we receive from a manufacturer of a Oki ML8810n can be divided into several groups. They are, among others:
- Oki technical drawings
- ML8810n manuals
- Oki product data sheets
- information booklets
- or energy labels Oki ML8810n
All of them are important, but the most important information from the point of view of use of the device are in the user manual Oki ML8810n.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Oki ML8810n, service manual, brief instructions and user manuals Oki ML8810n. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Oki ML8810n.

Similar manuals

A complete manual for the device Oki ML8810n, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Oki ML8810n by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Oki ML8810n.

A complete Oki manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Oki ML8810n - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Oki ML8810n, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Oki ML8810n, that we can find in the current document
3. Tips how to use the basic functions of the device Oki ML8810n - which should help us in our first steps of using Oki ML8810n
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Oki ML8810n
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Oki ML8810n in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Oki ML8810n?

Use the form below

If you did not solve your problem by using a manual Oki ML8810n, ask a question using the form below. If a user had a similar problem with Oki ML8810n it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)