-
Graco 311593N - page 1
311593N EN Operation E-Flo ® 4-Ball Piston Pumps Durable, energy efficient piston pumps f or high v olume paint circul ation applications. For prof essional use only . See page 3 f or model inf or mation, including maximum w ork ing pressure . See page 5 f or approv als. Important Safety Instructions Read all warnings and instructions in this manu ...
-
Graco 311593N - page 2
Related Manua ls 2 311593N Contents Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 E-Flo 4-Ball Piston P umps . . . . . . . . . . . . . . . . . 3 Maximum W orking Pressure and Pump Operationa l Limits . . . . . . . . . . . . . . . 3 Appro vals . ...
-
Graco 311593N - page 3
Models 311593N 3 Models E-Flo 4-Ball Piston Pumps Chec k your pump’ s identification plate (ID) f or the 6-digit part number of y our pump . Use the f ollowing mat r ix to define the const r uction of y our pump , based on the six digits . F or example , Pump P ar t No . EP2160 represen ts electric power ( E ), pump ( P ) , 230/460V motor ( 2 ), ...
-
Graco 311593N - page 4
Models 4 311593N ...
-
Graco 311593N - page 5
Approvals 311593N 5 Appr o vals The E-Flo Pump meet s requirements of the f ollowing appr ova l agencies. Ref er to the individual components f or other specific ha zardous location listings . Component P ar t No. Appr ovals Mechanica l Pump Motor AT E X EP1XXX EP3XXX UL/CSA EP2XXX EP4XXX IS Sensor Cir cuit EPX1XX c T3 Ex de IIC T4 - CESI 05 A TEX ...
-
Graco 311593N - page 6
Warnings 6 311593N Wa r n i n g s The f ollowing wa r nings are f or the setup , use, groundin g, maintenance, and repair of this equ ipment. The e xclama- tion point symbol ale r ts you to a general w ar ning and the hazard symbo ls refer to pr ocedure-specific risks. When these symbols appear in the body of this manual , refer b a ck to these W a ...
-
Graco 311593N - page 7
Warnings 311593N 7 ELECTRIC SHOCK HAZARD Improper groun ding, setup, or usage of th e system can cause electr ic shock. • T ur n off and disconnect power at main s witch bef o re disconnecting an y cables and bef ore servicing equipment. • Connect only to g rounded po wer source . • All electrical wir ing must be done by a qualified electrici ...
-
Graco 311593N - page 8
Overview 8 311593N Overview An electr ic motor (B ) provides input to a 75:1 gear reducer (GR), which driv es two fluid pumps (FP). See F IG . 1. The s troke positions of th e two pumps are offset to achiev e cons istent flow from the pum p assembly . S ee F IG . 2. The optional sensor circuit include s a top dead center (TDC) sensor which assists ...
-
Graco 311593N - page 9
Overview 311593N 9 Key: A E-Flo Electric Circula tion Pump B* Explosion-Proof Electric Moto r C* Local Control Box D* V ariable F requency Drive (VFD) E** System P owe r Disconnect Switch F* Electrical No ise Filter G* P o wer Module H* VFD/BPR Pneumatic Control Kit J** Electric P ow er Cable, VFD to Electr ic Motor K** Electric Control Cable, Loca ...
-
Graco 311593N - page 10
Overview 10 311593N ...
-
Graco 311593N - page 11
Ground the System 311593N 11 Gr ound the System The equipment m ust be grounded. Grou nding reduces the risk of static and electric shock b y providing an escape wire f or the electrical current due to st atic build up or in the e v ent of a shor t circuit. Ground the f ollo wing equipment: • Pump: use ground screw (GS) to attach a ground wire (Z ...
-
Graco 311593N - page 12
Controls and Indicators 12 311593N Contr ols and Indicator s V ariable Frequenc y Drive (VFD) Use a v ar iable frequency drive (VFD) accessory to pro- vide motor driv e control to t he pump . Graco supp lies accessory 240V and 480V VFDs that optimize pump performance. See manual 3115 96. Local Contr ol Bo x The local control bo x contains fiv e con ...
-
Graco 311593N - page 13
Setup 311593N 13 Setup Fill gear reducer reser v oir with oil Open the fill cap (FC) and f ill the gear reducer oil reser- v oir with 2 quar ts (1.9 liters) of Graco 288414 Oil (tw elve 1 quar t bottles). Chec k the oil lev el in the sight glass (SG) on the gear reducer housing. Do not ov erfill. See F IG . 5. NO TE: 2 quar ts br ings oil lev el ab ...
-
Graco 311593N - page 14
Operation 14 311593N Operation Pressure Relief Pr ocedure 1. Set ST ART/ST OP s witch (ST) to STOP . See F IG . 4. 2. Push in SECURE DISABLE (SD) s witch. 3. Open the bac k pressure regulat or and all fluid drain valv es in the system, having a waste conta iner ready to ca tch drainage. Leav e op en until you are ready to pressuri ze system again. ...
-
Graco 311593N - page 15
Operation 311593N 15 F IG . 7: Motor Speed and Flo w Char t Flow Rate gpm (lpm) 30 (114) 25 (95) 20 (76) 15 (57) 10 (38) 5 (19) Pump Cycles per Min ute 0 4 8 12 16 20 24 10 (300) 20 (600) 30 (900) 40 (1200) 50 (1500) 60 (1800) Motor Speed in Hz (rpm) 0 A B C Equations f or each line: 2000 cc Flow (gpm) = 1.13 x 1500 cc Flow (gpm) = 0.811 x 1000 cc ...
-
Graco 311593N - page 16
Maintenance 16 311593N Maintenance Preventive Maintenance Schedule Estab lish a prev entiv e maintenance schedule based on the equipmen t’ s repair histor y . Chec k Gear Reducer Oil Level Every day , check the oil le vel in the sight glass (SG) on the gear r educer , with th e motor r unning. O il le vel (with motor running) should f all betwee ...
-
Graco 311593N - page 17
Maintenance 311593N 17 Flushing • Flush bef ore changing colors , bef ore storing, and bef ore repairing equipment. • Flush at th e lowest pressure p ossible . Ch eck con- nectors for leaks and ti ghten as nece ssar y . • Flush with a fluid that is c ompatible with the fluid being dispense d and the equipment wett ed par ts. 1. Follo w Pressu ...
-
Graco 311593N - page 18
Technica l Data 18 311593N T echnical Data Maximum Working Pressu re . . . . . . . . . . . . . . E-Flo 1500: 42 5 psi (2.93 MP a, 29.3 bar) E-Flo 2000: 460 psi (3 .22 MP a, 32.2 bar) E-Flo 3000: 330 psi (2.3 1 MP a, 23.1 bar) E-Flo 4000: 250 psi (1.7 5 MP a, 17.5 bar) Maximum Fluid T e mperature . . . . . . . . . . . . . . 150°F (66°C) Electr ica ...
-
Graco 311593N - page 19
Technical Data 311593N 19 Pressure and Flow Capability of E-Flo F amily with 50 Hz Motor (continuous production use) Fluid Pressure psi (MP a, bar) 350 (2.41, 24.1) 300 (2.10, 21.0) 250 (1.72, 17.2) 200 (1.4, 14.0) 150 (1.03, 10.3) 100 (0.70, 7.0) 50 (0.35, 3.5) 0 Fluid Flo w in gpm (lpm) 5 (19) 10 (38) 15 (57) 20 (76) 25 (95) A B C 400 (2.80, 28.0 ...
-
Graco 311593N - page 20
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. T his manual contains English. MM 311593 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Kore ...
Do you have a question concerning Graco 311593N?
Use the form below
If you did not solve your problem by using a manual Graco 311593N, ask a question using the form below. If a user had a similar problem with Graco 311593N it is likely that he will want to share the way to solve it.