English dropdown-ico

Manual Sonic Frontiers Power 2

17 pages 0.5 mb
Download

Go to site of 17

Summary
  • Sonic Frontiers Power 2 - page 1

    Operating Manual for the Sonic Frontiers Power 2 Stereo Amplifier ...

  • Sonic Frontiers Power 2 - page 2

    Operating Manual for the Sonic Frontiers Power 2 Stereo Amplifier W e at Sonic Frontiers hope you will derive many years of listening pleasure with your new Power 2 Amplifier. This Operating Manual contains important information regar d- ing the operation and care of this Amplifier. Be sure to read this manual carefully and follow these instruction ...

  • Sonic Frontiers Power 2 - page 3

    1 Unpacking At this point we can assume that you have successfully opened the box flaps and found this manual. The box was designed to ensure the safe transport of the amplifier, Sonic Frontiers strongly recommends the storage of the Power 2 box in a safe, dry place. In the event that the amplifier may have to be shipped in the future, the original ...

  • Sonic Frontiers Power 2 - page 4

    2 Quick Setup At this point we urge you to read and understand this manual in its entirety. But if you desire immediate action and have skill and/or past experience with tube hardware, fol - low these steps. 1. Place the amp on a hard flat surface that will not impede airflow under the amplifier’ s chassis (carpeting or area rugs ar e NOT accepta ...

  • Sonic Frontiers Power 2 - page 5

    3 Reference Diagrams This drawing is refer red to as the “Tube Top” within the instructional text. T ube locations V1 to V3 and LV1 to LV3 indicate placement for the six 6922 tubes. T ube locations V4 and LV4 indicate placement for the two 5687 tubes. Locatio ns V5 to V8 and L V5 to LV 8 indic at e plac e ment for the 6550C/K T88 powe r tubes. ...

  • Sonic Frontiers Power 2 - page 6

    4 C Power Switch D Standby Switch E Power LED (Green - Power; Red - Mute; Orange (Red + Green) - One Channel in Mute) F Standby LED (Green - Operate; Red - Standby) G Detachable IEC Power Cord Socket H Fuse Location I Left and Right Channel Input Selector Switches J Left and Right Channel Balanced XLR Inputs K Left and Right Channel Single-Ended RC ...

  • Sonic Frontiers Power 2 - page 7

    5 Installing the Tubes Be sure the amplifier is OFF (Power Switch Out) before installing any tubes or when any of the tube sockets are empty . W earing the cotton gloves provided with the amplifier when handling tubes will prevent skin oils from depositing on the glass surface of the tubes. The oils could cause the tubes to become “gassy” and f ...

  • Sonic Frontiers Power 2 - page 8

    6 When installing the 6550C or KT88 power tubes, match the numbers designated on the metal base of the tube or the tube boxes to the cor r esponding markings printed on the tube top (V5 through V8 and LV5 through LV8) and be sure the center pin key locator is in alignment with the slot in the center of the socket. Again push down the tube, rocking ...

  • Sonic Frontiers Power 2 - page 9

    7 Biasing of the Power Tubes Bias voltage applied to the grids of the power tubes in the output stage should be checked from time to time (once a month) to keep these tubes operating at the optimum operating point. A properly biased power tube will have a longer, happier life. T o check the bias of the 6550C/KT88 tubes, place the amplifier in mute ...

  • Sonic Frontiers Power 2 - page 10

    8 Controls, Functions and Connections Front Panel Refer to Reference Diagrams. C Power Switch This switch provides control over the AC power from your wall outlet. When OFF (out position) nothing on the amplifier is functional. When ON (depressed) the amplifier will operate normally (green power LED indicates ON; Red Power LED indicates ON but in M ...

  • Sonic Frontiers Power 2 - page 11

    9 Damage due to bypassing the fuse or due to replacement of a fuse of higher ratings will not be covered under the warranty. To access the fuse, insert the slotted screwdriver , pushing to compress the internal spring and turn counterclockwise to unlock the housing. The spring will then eject the fuse and the housing. I Left and Right Channel These ...

  • Sonic Frontiers Power 2 - page 12

    10 Adjustment for Load Impedance Note: Adjustment for load impedance should only be done by an authorized Sonic Frontiers dealer, distributor or service technician. Any damage to the amplifier as a result of a person(s) not authorized by Sonic Frontiers will not be covered under warranty . W arning: Dangerous voltages exist within this amplifier . ...

  • Sonic Frontiers Power 2 - page 13

    11 4.Using the slot screwdriver provided with the amp, deal with one connection at a time, loosening off the tap screws of the first spade lug connection and tightening to the desired tap. The final connections should resemble these renderings: 8 Ohm Impedance Connections 4 Ohm Impedance Connections 2 Ohm Impedance Connection 5. Repeat for each cha ...

  • Sonic Frontiers Power 2 - page 14

    12 Care and Maintenance Placement The amplifier must be placed on a har d flat sur face with plenty of unobstructed space around the Power 2 to allow for free movement of air for proper cooling. If the amplifier is to be placed on a carpeted floor, a Wood, Ceramic, Concrete, Marble... tile or slab 18” x 22” (or larger) must be place under the P ...

  • Sonic Frontiers Power 2 - page 15

    13 T r oubleshooting If at any time the amplifier should fail to work, follow these steps: 1. Check that all tubes are fully seated in cor r ect sockets and all tube filaments are lit. 2. Check all connections at the rear panel. 3. Check that the amplifier is not in MUTE mode. 4. Check that the proper input is selected via the Selector Switch. 5. C ...

  • Sonic Frontiers Power 2 - page 16

    14 W arranty Disclaimer of Liability Under no circumstances does Sonic Frontiers, Inc. assume liability or responsibility for injury or damages sustained in the use or operation of this equipment or for damages to any other equipment connected to it. Sonic Frontiers, Inc. reserves the right to make design changes or improvements without the obligat ...

  • Sonic Frontiers Power 2 - page 17

    15 Specifications Note: Power ratings based on a nominal power line input. All specifications are made on the 8 ohm taps, utilizing an 8 ohm load unless otherwise specified. Power Output: 110 watts continuous at 8, 4 and 2 ohms from 20 Hz to 20 kHz with less than 1% total harmonic distortion terminated with rated load (typically <0.5% @ 110 watt ...

Manufacturer Sonic Frontiers Category Stereo Amplifier

Documents that we receive from a manufacturer of a Sonic Frontiers Power 2 can be divided into several groups. They are, among others:
- Sonic Frontiers technical drawings
- Power 2 manuals
- Sonic Frontiers product data sheets
- information booklets
- or energy labels Sonic Frontiers Power 2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sonic Frontiers Power 2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sonic Frontiers Power 2, service manual, brief instructions and user manuals Sonic Frontiers Power 2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sonic Frontiers Power 2.

Similar manuals

A complete manual for the device Sonic Frontiers Power 2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sonic Frontiers Power 2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sonic Frontiers Power 2.

A complete Sonic Frontiers manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sonic Frontiers Power 2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sonic Frontiers Power 2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sonic Frontiers Power 2, that we can find in the current document
3. Tips how to use the basic functions of the device Sonic Frontiers Power 2 - which should help us in our first steps of using Sonic Frontiers Power 2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sonic Frontiers Power 2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sonic Frontiers Power 2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sonic Frontiers Power 2?

Use the form below

If you did not solve your problem by using a manual Sonic Frontiers Power 2, ask a question using the form below. If a user had a similar problem with Sonic Frontiers Power 2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)