English dropdown-ico

Manual KitchenAid Pro Line Series

32 pages 0.41 mb
Download

Go to site of 32

Summary
  • KitchenAid Pro Line Series - page 1

    Installation Instructions and Use and Care Guide IMPOR T ANT : Read and sa ve these instructions. IMPOR T ANT : I nstaller: Leav e Installation Instructions with the homeowner . Homeowner: K eep Installation Instructions f or future ref erence. Save Installation Instr uctions f or local electr ical inspector's use. Pa r t N o. 437500563/828534 ...

  • KitchenAid Pro Line Series - page 2

    2 Bef ore y ou star t... Proper installation is your responsibility: • Hav e a qualified technician install this r ange hood. • Comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the rear wall. Range hood location should be awa y from strong draft are ...

  • KitchenAid Pro Line Series - page 3

    3 Pa r ts supplied: mounting screws wall anchors wall anchors c himney mounting brackets damper c himney screws upper c himney hood and vent motor assembly lower c himney Pa r ts needed: • 2 - U .L.- or C.S.A.- listed, 1/2" (12.7 mm) strain r elief • pow er supply cable • 1 - wall or r oof cap • 6" round metal v ent system • 2 - ...

  • KitchenAid Pro Line Series - page 4

    4 V ented installations min. and max. ceiling or soffit height examples distance from hood to cooking surface (X) minimum maximum 24" (61 .0 cm) 7' 6-3/8" (2.30 m) 8' 6" (2.59 m) 26" (66.0 cm) 7' 8-3/8" (2.35 m) 8' 8" (2.64 m) 28" (71 .1 cm) 7' 1 0-3/8" (2.40 m) 8' 1 0" (2.6 ...

  • KitchenAid Pro Line Series - page 5

    5 V enting methods This range hood is set for venting to the outside. For non-vented (recirculating) installation, a conversion kit is required. S ee "Non-vented (recirculating) installations" on page 2. V ent system needed for installation is not included. Use 6" (15.2 cm) round vent. Ve nt system can terminate either through the ro ...

  • KitchenAid Pro Line Series - page 6

    height and personal preference, determine the distance “X” needed between the cooking surface and the bottom of the hood. T o this distance, add 15-1/8" (34.8 cm) and draw a horizontal line about 24" (61 .0 cm) centered on the vertical centerline at this distance. 5. Mark two points on eac h side of the horizontal line 4-9/1 6" ( ...

  • KitchenAid Pro Line Series - page 7

    7 7. Place one of the c himney brac kets against the w all so that its top edge is 1/16” (2.0 mm) from the ceiling or soffit and level. • Align the center notc hes of the brac ket and the centerline. • Mark the centers of the brac k et holes 8. Place the other c himney brac ket on the wall so that it’ s lower edge is 1 6-3/1 6” (41 .1 cm) ...

  • KitchenAid Pro Line Series - page 8

    F or v ent ed installations: 22. Install the damper on top of the exhaust opening. Make sure the damper opens freely . 8 Install c himne y sections Electr ical connection Electrical Shock Hazar d Disconnect power bef ore making electrical connections. Connect ground wire to green ground scre w in terminal box. Fa ilure to do so can result in death ...

  • KitchenAid Pro Line Series - page 9

    Before you begin, make sure that the range hood is turned off and that the lamps have had sufficient time to cool. To replace a halogen lamp: • Disconnect power . • Use a Phillips screwdriver and remove the retainer clips located at eac h end of the lamp panel. •S lide the lamp panel all the way to the right. Lower the lef t end of the panel ...

  • KitchenAid Pro Line Series - page 10

    1- 80 0-442-9991 or order on-line at www.applianceaccessories.com and ask for part number 8171 420. T o order from Canada, call 1 -80 0-807 -6777 . • If commercial cleaners are used, follow label directions. Do not use products that contain ch lorine (bleac h). Chlorine is a corrosive substance. F or routine cleaning and fingerprints, use liquid ...

  • KitchenAid Pro Line Series - page 11

    11 Wa rr anty Kitc henAid ® Range Hood W ar r anty LENGTH OF W ARRANTY KitchenAid WILL P A Y FOR FULL ONE-YEAR WARRAN TY Labor and any par ts of your range hood (except light bulbs and F rom Date of P urc hase filters) whic h are defecti ve in materials or workmanship when this appliance is operated and maintained according to instructions attac h ...

  • KitchenAid Pro Line Series - page 12

    12 Requesting Assistance or Service Call the KitchenAid Cust omer Inter action Center t oll-fr ee at 1 -80 0-422-1230. Our consultants ar e av ailable to assist y ou. When calling: Please know the purc hase date, and the complete model and serial number of your appliance This information will help us better respond to your request. Our consultants ...

  • KitchenAid Pro Line Series - page 13

    13 2. If y ou need service ✝ ... Contact your nearest Kitc henAid Canada Appli- ance Service branc h or authorized servicing outlet to service your appliance. (See list below .) Make sure the service company you contact is authorized to service your appliance during the warr a n ty period. 1. If the pr oblem is not due to one of the it ems list e ...

  • KitchenAid Pro Line Series - page 14

    14 Not es ...

  • KitchenAid Pro Line Series - page 15

    15 Not es ...

  • KitchenAid Pro Line Series - page 16

    Pa rt No. 43750 0563/8285349 © 20 03 Kitc henAid ® Registered trademark/™ trademark of Kitc henAid, U .S.A., Kitc henAid Canada licensee in Canada 4/20 03 P rinted in Italy ...

  • KitchenAid Pro Line Series - page 17

    Instructions d’installation et Guide d’utilisation et d’entretien IMPOR T ANT : Lire et conserver ces instructions. IMPOR T ANT : Installateur : Remettre les instructions d’installation au propriétaire de l’appareil. Propriétaire : Conserver les instructions d’installation pour consultation ultérieure. Conserver les instructions d’ ...

  • KitchenAid Pro Line Series - page 18

    2 Av ant de commencer ... C’est à vous qu’incombe la responsabilité d’une installation correcte . • Demander à un technicien qualifié d’installer cette hotte. • Respecter lors de l’installation les dégagements de séparation spécifiés sur la plaque signalétique de l’appareil. Important : Respecter les prescriptions de tous l ...

  • KitchenAid Pro Line Series - page 19

    3 Pièces f ournies : vis de montage che villes d’ancrage che villes d’ancrage brides de montage de la cheminée v olet de réglage vis c heminée c heminée – section supérieure hotte et moteur de ventilation c heminée – section inférieure Pièces nécessaires : • 2 serre-câbles de 12,7 mm (1/2 po) (homologation U .L. ou C.S.A.) • ...

  • KitchenAid Pro Line Series - page 20

    4 Installation av ec déchar ge à l’extér ieur Hauteurs libres min. et max. sous plafond ou soffite distance entre la hotte et la table de cuisson (X) minimum maximum 61 cm (24 po) 2,30 m (7 pi 6-3/8 po) 2,59 m (8 pi 6 po) 66,0 cm (26 po) 2,35 m (7 pi 8-3/8 po) 2,64 m (8 pi 8 po) 71,1 cm (28 po) 2,40 m (7pi 10-3/8 po) 2,69 m (8 pi 10 po) 76,2 c ...

  • KitchenAid Pro Line Series - page 21

    Note : On déconseille l’emploi de conduit d’é vacuation fle xible . En cas d’utilisation de conduit d’é vacuation fle xible , on doit tenir compte du f ait que la longueur effectiv e de un pied de conduit fle xible correspond à 61 cm (2 pi) de conduit métallique rigide. (Ex emple : la longueur effectiv e d’un coude de conduit fle xib ...

  • KitchenAid Pro Line Series - page 22

    6 4. Selon la hauteur sous plafond ou sous soffite, ou selon les préférences personnelles, déterminer la distance « X » à établir entre la table de cuisson et le bas de la hotte. Ajouter 34,8 cm (15 1/8 po) à cette distance et tracer une ligne horizontale à environ 61 cm (24 po) de la table de cuisson, perpendiculaire à l’axe vertical. ...

  • KitchenAid Pro Line Series - page 23

    16 . Soulever la hotte; placer les brides de montage de la hotte sur les vis de montage. Bien serrer les vis. 17 . Établir l’aplomb de la hotte – ajuster les deux vis de réglage de l’aplomb selon le besoin (voir étape 13). 18 . Si cela n’a pas déjà été fait, centrer le trou de câblage de la boîte de connexion sur le trou de travers ...

  • KitchenAid Pro Line Series - page 24

    8 Installations des sections de c heminée Installation avec déc harge à l’extérieur : 22. Installer le module du volet au sommet, sur l’ouverture de décharge. Vérifier que le volet peut manœuvrer librement. 23. Connecter le circuit d’évacuation; établir l’étanchéité de chaque connexion avec du ruban adhésif pour conduits. Passe ...

  • KitchenAid Pro Line Series - page 25

    9 Renseignements d’utilisation et d’entretien A VER TISSEMENT – POUR MINIMISER LE RISQUE D’INCENDIE, CHOC ÉLECTRIQUE OU DOMMAGES CORPORELS, RESPECTER LES INSTRUCTIONS SUIV AN TES : Utiliser cet appareil uniquement dans les applications envisagées par le fabricant. P our toute question, contacter le fabricant. A vant d’entreprendre un tr ...

  • KitchenAid Pro Line Series - page 26

    10 Netto y a g e Filtres métalliques : Dépose des filtres : Note : Utiliser les deux mains pour enlever le filtre - une main pour tirer et faire tourner le bouton, et l’autre main pour tenir le filtre pour qu’il ne tombe pas. • T irer le bouton vers l’avant (vers l’avant de la hotte) tout en faisant tourner le bouton dans le sens invers ...

  • KitchenAid Pro Line Series - page 27

    11 Filtre à charbon de rechange : Produit n o 8285507. Pour utilisation dans une installation sans décharge à l’extérieur (recyclage) – n os 8285505 et 8285506 seulement. A ccessoir es disponibles chez les r ev endeurs Schéma de câb lage Surfaces extérieures : • Ne pas utiliser de la laine d’acier ou un tampon à récurer savonneux. ...

  • KitchenAid Pro Line Series - page 28

    12 KITCHENAID ET KITCHENAID CANAD A NE SONT P AS RESPONSABLES POUR LES DOMMAGES FOR TUITS OU INDIRECTS. Cer tains États ou cer taines provinces ne permettent pas l’exclusion ou la limitation des dommages fortuits ou indirects de sor te que cet te exclusion ou limitation peut ne pas s ’appliquer dans votre cas. Cett e gar antie vous confèr e d ...

  • KitchenAid Pro Line Series - page 29

    13 Demande d'assistance ou de service T éléphoner au Centre d’int eraction a vec la clientèle KitchenAid sans fr ais d’inter urbain au 1 -80 0-422-1230. Nos consultants sont disponibles pour vous aider . Lo rs de votre appel, veuillez connaître la date d’ac hat et les numéros au complet de modèle et de série de votre appareil. Ces ...

  • KitchenAid Pro Line Series - page 30

    14 2. Si v ous av ez besoin de service ✝ ... Communiquer avec la succursale ou établissement de service autorisé de Kitc henAid Canada le plus proc he pour l’entretien de votre appareil. (V oir liste ci-dessous.) S’assurer que la compagnie de service que vous contactez est autorisée à faire l’entretien de votre appareil durant la pério ...

  • KitchenAid Pro Line Series - page 31

    15 Not es ...

  • KitchenAid Pro Line Series - page 32

    Pièce N° 43750 0563/8285349 © 20 03 Kitc henAid ® Marque déposée /™ Marque de commerce de Kitc henAid, U.S.A., Kitc henAid por teur de licence au Canada 4/20 03 Imprimé en Italie ...

Manufacturer KitchenAid Category Ventilation Hood

Documents that we receive from a manufacturer of a KitchenAid Pro Line Series can be divided into several groups. They are, among others:
- KitchenAid technical drawings
- Pro Line Series manuals
- KitchenAid product data sheets
- information booklets
- or energy labels KitchenAid Pro Line Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual KitchenAid Pro Line Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals KitchenAid Pro Line Series, service manual, brief instructions and user manuals KitchenAid Pro Line Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product KitchenAid Pro Line Series.

Similar manuals

A complete manual for the device KitchenAid Pro Line Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use KitchenAid Pro Line Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of KitchenAid Pro Line Series.

A complete KitchenAid manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual KitchenAid Pro Line Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the KitchenAid Pro Line Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the KitchenAid Pro Line Series, that we can find in the current document
3. Tips how to use the basic functions of the device KitchenAid Pro Line Series - which should help us in our first steps of using KitchenAid Pro Line Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with KitchenAid Pro Line Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of KitchenAid Pro Line Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning KitchenAid Pro Line Series?

Use the form below

If you did not solve your problem by using a manual KitchenAid Pro Line Series, ask a question using the form below. If a user had a similar problem with KitchenAid Pro Line Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)