English dropdown-ico

Manual Datalogic Scanning 1000I

176 pages 4.55 mb
Download

Go to site of 176

Summary
  • Datalogic Scanning 1000I - page 1

    Magellan TM 1000i On-Coun ter Pr esentation Omnidir ectional Bar Code Reader Pr oduc t Refer enc e Guide ...

  • Datalogic Scanning 1000I - page 2

    Datalogic Scanning, Inc. 959 T err y Street Eugene, Oregon 974 02 T eleph one: (541) 683-5700 F ax: (541) 345- 7140 An Unpublished W o rk - All rights r eserved. No par t of the contents of this documentation or the procedures described therein ma y be repr oduced or tran smitted in any f orm or by an y means without prior written pe rmission of Da ...

  • Datalogic Scanning 1000I - page 3

    Product Reference Guide i- i Table of Contents About This Ma nual ............... .......... ........... .......... ............. .......... ........... .......... ........... ........ .. 1-1 Manual Convention s ........... .......... ........... .......... ........... .......... ........... ........... .......... ........ 1-1 Connecting the Scan n ...

  • Datalogic Scanning 1000I - page 4

    i-ii Magellan ® 1000i Wand Idle State ...... .............. ............. .............. ........... .............. ............. ... 3-27 Signal Speed .................. .............. .............. ............. .............. .............. ..... 3-28 Transmit Trailing Noise ............... .............. .............. ............. ......... ...

  • Datalogic Scanning 1000I - page 5

    Product Reference Guide i-iii Start/Stop Character s . ........... ........... .......... ............. .......... ........... .......... ........... .......... . 5-27 Code 39 Full A SCII ........ .......... ........... .......... ........... .......... ........... .......... ............. .........5-28 Length Control .............. .......... .... ...

  • Datalogic Scanning 1000I - page 6

    i-iv Magellan ® 1000i Minimum Reads .................. .......... ........... ............ ........... .......... ........... .......... ........... ... 5-67 2D Symbologie s .................. ........... .......... ........... .......... ........... ........... .......... ........... ......... .. 6-2 PDF 417 ...... ........... ........... ....... ...

  • Datalogic Scanning 1000I - page 7

    Produc t Refe rence Gu ide 1-1 Chapter 1 Getting Star ted The Magellan ® 1000i Omni-D i rectional I maging Scanner offers hands-free scanning for small, easily handled items and handheld scanning for bulkier items. Its aggr essive imaging perfor- mance and intuitive operation reduces user trai ning and speeds checkout for better customer service. ...

  • Datalogic Scanning 1000I - page 8

    Getting Started 1-2 Magellan ® 1000i C onnecting the S canner The scanner kit you order ed to match your interf ace should provide a comp atible cab le for your installation. U se the appropriate instructions below to connect the scanner to the terminal, PC or other host device. U pon completing the connection via the appropri ate interface instru ...

  • Datalogic Scanning 1000I - page 9

    Programming Product Reference Guide 1-3 Wand Emulation Connection — Connect the scanner to the appropriated port on the ter- minal/PC using the correct cable for the interface type you or dered. Re ference Figure 2 . IBM Connection — Connect the scanner to the IBM port on the terminal/PC using the cor- rect IBM c abl e. Re feren ce Figure 2 . K ...

  • Datalogic Scanning 1000I - page 10

    Getting Started 1-4 Magellan ® 1000i LED and Beeper Indicators The scanner ’ s beeper sounds and its green LE D illuminates to indica te various functions or errors on the scanner . The tables belo w list these indications. One exception to the behaviors listed in the tables is that the scanner’ s functions are programmable, and may or may not ...

  • Datalogic Scanning 1000I - page 11

    Error Codes Product Reference Guide 1-5 Error C odes U pon startup, if the scanner flashes its indicato r LED or sounds an unexpected series of beep tones (other than normal power-up indications) , this means the scanner has not passed its auto- matic Selftest and has entered FRU 1 isolation mode. If the scanner is reset or the trigger is pulled, t ...

  • Datalogic Scanning 1000I - page 12

    Getting Started 1-6 Magellan ® 1000i NOTES ...

  • Datalogic Scanning 1000I - page 13

    Produc t Refe rence Gu ide 2-1 Chapter 2 Gen er al F ea tu re s Double Read T imeout The Double R ead T imeout feature sets a time li mit that determines how much time must pass before reading the same label again (e.g. two identical items in succession). ST ART / END PROGRAMMING BARCODES 0.1 Second 0.2 Second 0.3 Second 0.4 Second DEF A UL T 0.5 S ...

  • Datalogic Scanning 1000I - page 14

    General Features 2-2 Magellan ® 1000i Double Read Timeout — cont. ST ART / END PROGRAMMING BARCODES 0.7 Second 0.8 Second 0.9 Second 1 Second ...

  • Datalogic Scanning 1000I - page 15

    Label Gone Timeout Product Reference Guide 2-3 Label Gone T imeout This feature sets the time after the last label se gment is seen before the scanner prepar es for a new label. Pr oductivit y Index Reporting (PIR) When PIR is enabled, label quality data is appended to decoded data before being presented to the POS. The PIR feature allo ws the scan ...

  • Datalogic Scanning 1000I - page 16

    General Features 2-4 Magellan ® 1000i Sleep Mode This feature specifies t he amount of time with no barcode reads bef ore t he scanner enters sleep mode. ST ART / END PROGRAMMING BARCODES 15 Seconds 30 Seconds 1 Minute 2 Minutes 3 Minutes 4 Minutes 5 Minutes ...

  • Datalogic Scanning 1000I - page 17

    Sleep Mode Product Reference Guide 2-5 Sleep Mode — cont. ST ART / END PROGRAMMING BARCODES 6 Minutes 7 Minutes 8 Minutes 9 Minutes 10 Minutes DEF A UL T 12 Minutes 15 Minutes 30 Minutes 1 Hour ...

  • Datalogic Scanning 1000I - page 18

    General Features 2-6 Magellan ® 1000i LED and Beeper Indicators Pow e r O n A l e r t Disables or enables the indication (a single beep ) that the scanner has finished all its power up tests and is now r eady for operation. ST ART / END PROGRAMMING BARCODES Disab le Enable DEF A UL T ...

  • Datalogic Scanning 1000I - page 19

    LED and Beeper Indicators Product Reference Guide 2-7 Goo d Read: When to In dicate This feature specifies when the scanner will prov ide indication (beep and/or flash its green LED) upon successful ly readin g a barcode. Choices are: • Good Read = I ndicate after decode • Good Read = I ndicate after transmit • Good Read = I ndicate after CTS ...

  • Datalogic Scanning 1000I - page 20

    General Features 2-8 Magellan ® 1000i Good Read Beep C ontr ol This feature enables/disables the scanner’ s ability to beep upon a successf ul decode of a barcode. Good Read Beep F requency Adjusts the good read beep to sound at a selectab le low , medium or high frequency , selectable from the list below . (Controls the beeper’ s pitch /tone. ...

  • Datalogic Scanning 1000I - page 21

    LED and Beeper Indicators Product Reference Guide 2-9 Good Read Beep Length S pecifies the duration of a good read beep. ST ART / END PROGRAMMING BARCODES 60msec 80msec DEF A UL T 100msec 120msec 140msec 160msec 180msec 200msec ...

  • Datalogic Scanning 1000I - page 22

    General Features 2-10 Magellan ® 1000i Good Read Beep V olume Selects the bee per volume (loudness) upon a good r ead beep. There ar e three selectable volume levels. ST ART / END PROGRAMMING BARCODES Low Medium High DEF A UL T ...

  • Datalogic Scanning 1000I - page 23

    Scanning Features Product Reference Guide 2-11 Scanning F eatures T argeted S canni ng Mode U pon pressing the button, the scanner will project an aiming pattern to assist in centering over the barcode. Scanning then takes place as soon as the button is released. Configuration options for T argeted Scanning Mode ar e: • T arget Mode A ctive T ime ...

  • Datalogic Scanning 1000I - page 24

    General Features 2-12 Magellan ® 1000i T arget Mode Linger T ime S pecifies the time duration the scanner remains in the targeted mode of operation after r eading a barcode before reverting to Omni-directional Mode. ST ART / END PROGRAMMING BARCODES Shor t Duration Medium Duration DEF A UL T Long Duration ...

  • Datalogic Scanning 1000I - page 25

    Scanning Features Product Reference Guide 2-13 W ake Up Intensity This feature indicates the percentage of ambient light change which will trigger the scanner to wake up from S leep M ode. Lo wer settings pro vide gr eater sensitivity . The seelectable range for this setting is 5% to 15%. ST ART / END PROGRAMMING BARCODES 5% 6% 7% 8% 9% 10% DEF A U ...

  • Datalogic Scanning 1000I - page 26

    General Features 2-14 Magellan ® 1000i Wake Up Intensity — cont. ST ART / END PROGRAMMING BARCODES 13% 14% 15% ...

  • Datalogic Scanning 1000I - page 27

    Produc t Refe rence Gu ide 3-1 Chapter 3 Inter f ace Related F eatures At the time of this writing, the Scanner supports the inter faces listed in Ta b l e 3 - 1 . Select the desired interface type from the table, then re fe rence the page number give n for the customizable features section associated with each interface. See Ta b l e 3 - 2 for a d ...

  • Datalogic Scanning 1000I - page 28

    Interface Related Features 3-2 Magellan ® 1000i Table 3-2. Keyboard Wedg e Interface Refer ence I/F T ype PCs Suppor ted A PC/XT w/Alter nate K ey Encoding B A T , PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Ke y Encoding C PS/2 25 and 30 w/Alternate Ke y Encoding D PC/XT w/Standard K ey Encoding E A T , PS/2 25-286, 30-286, ...

  • Datalogic Scanning 1000I - page 29

    Interface Selection Product Reference Guide 3-3 Inte r face Selection ST ART / END PROGRAMMING BARCODES RS-232 Standard RS-232 Wincor-Nixdorf IBM 4683 P or t 5B IBM 4683 P or t 9B IBM 4683 P or t 17 USB-OEM USB K eyboard W and Emulation USB COM ...

  • Datalogic Scanning 1000I - page 30

    Interface Related Features 3-4 Magellan ® 1000i Interface Selection — cont. ST ART / END PROGRAMMING BARCODES K eyboard W edge A K eyboard W edge B K eyboard W edge C K eyboard W edge D K eyboard W edge E K eyboard W edge F K eyboard W edge G K eyboard W edge H K eyb oard Wedge I K eyboard W edge J ³ 000132 ...

  • Datalogic Scanning 1000I - page 31

    Interface Selection Product Reference Guide 3-5 Interface Selection — cont. ST ART / END PROGRAMMING BARCODES K eyboard W edge K K eyboard W edge L K eyboard W edge M K eyboard W edge N K eyboard W edge O K eyboard W edge P K eyboard W edge Q K eyboard W edge R K eyboard W edge S ³ 00013 B ³ 00013 ...

  • Datalogic Scanning 1000I - page 32

    Interface Related Features 3-6 Magellan ® 1000i Interface Selection — cont. ST ART / END PROGRAMMING BARCODES K eyboard W edge T K eyboard W edge U K eyboard W edge V K eyboard W edge W K eyboard W edge X K eyboard W edge Y ...

  • Datalogic Scanning 1000I - page 33

    Interface Features Product Reference Guide 3-7 Inter f ace F eatures Obey/Ignore Host C ommands When set to ignore host commands, the scanner will ignore all host commands ex cept for the minimum set necessar y to keep the inter face active and transmit labels For normal operation of the interface, select Obey Host Commands. ST ART / END PROGRAMMIN ...

  • Datalogic Scanning 1000I - page 34

    Interface Related Features 3-8 Magellan ® 1000i Interface Features — cont. Host T ransm ission Buffers S pecifies the number of host transmission(s) that may be buffered. B y buffering data from a bar- code, the scanner can continue to read a new barcode while the old one is being transmitted to the host. Selecting BUFFERS = 1 means that the fir ...

  • Datalogic Scanning 1000I - page 35

    Interface Features Product Reference Guide 3-9 RS-232 Inter face F eatur es ST ART / END PROGRAMMING BARCODES 1200 Baud 2400 Baud 4800 Baud 9600 Baud DEF A UL T 19200 Baud 38400 Baud 57600 Baud 115200 Baud ³ ...

  • Datalogic Scanning 1000I - page 36

    Interface Related Features 3-10 Magellan ® 1000i RS-232 Interface Features — cont. ST ART / END PROGRAMMING BARCODES 7 Data Bits 8 Data Bits DEF A UL T 1 Stop Bit DEF A UL T 2 Stop Bits Par i t y = N o n e DEF A UL T P arity = Even P arity = Odd ...

  • Datalogic Scanning 1000I - page 37

    Interface Features Product Reference Guide 3-11 RS-232 Interface Features — cont. Hardware Flow Control Disable Hardw are Control— The scanner transmits to the host regardless of any activity on the CTS line. Enable CTS Flow Control— The CTS signal controls transmission of data to the host. Enable CTS Scan Control— The CTS line must be acti ...

  • Datalogic Scanning 1000I - page 38

    Interface Related Features 3-12 Magellan ® 1000i RS-232 Interface Features — cont. Interchara cte r Delay This delay is inserted after each data character tr ansmitted. If the transmission speed is too high, the system may not be able to receive all charac ters. Y ou may need to adjust the delay to make the system work properly . ST ART / END PR ...

  • Datalogic Scanning 1000I - page 39

    Interface Features Product Reference Guide 3-13 Intercharacter Delay — cont. So ft ware Flow Control Disables/Enables software cont rol using X ON /X OFF characters . ST ART / END PROGRAMMING BARCODES Interchar Delay = 80 msec Interchar Delay = 90 msec ST ART / END PROGRAMMING BARCODES Disable Software Flow Control DEF A UL T Enable Software Flo ...

  • Datalogic Scanning 1000I - page 40

    Interface Related Features 3-14 Magellan ® 1000i RS-232 Interface Features — cont. Host Ec ho When enabled, this feature passes all data throug h the scanner to the host as it comes in. This feature is u sed for applications where “ daisy ch aining” of RS-232 devices onto the same cable is necessary . If, for example, one of the devices in t ...

  • Datalogic Scanning 1000I - page 41

    Interface Features Product Reference Guide 3-15 RS-232 Interface Features — cont. Host Echo Quiet Interval This setting specifies the time interval of RS-232 channel inactivity which must transpire before the scanner will break the host echo loop to transmit the bar code data that has just been scanned to the host. ST ART / END PROGRAMMING BARCOD ...

  • Datalogic Scanning 1000I - page 42

    Interface Related Features 3-16 Magellan ® 1000i Host Echo Quie t Interval — cont. Signal V oltage: Normal/T TL S pecifies whether the RS-232 interface provides TTL levels on the output pins TxD and R TS. ST ART / END PROGRAMMING BARCODES Host Echo Quiet Inter v al = 80msec Host Echo Quiet Interval = 90msec Host Echo Quiet Inter v al = 100msec S ...

  • Datalogic Scanning 1000I - page 43

    Interface Features Product Reference Guide 3-17 RS-232 Inv ert Enables/disables inversion of RS-232 TXD and RXD signals. Beep on ASCII BEL Enables/disables ability of scanner to beep (sou nd a good r ead tone) on receiving an ASCII BEL (07 hex). ST ART / END PROGRAMMING BARCODES Disable RS-232 In ver t DEF A UL T Enable RS-232 In vert ST ART / END ...

  • Datalogic Scanning 1000I - page 44

    Interface Related Features 3-18 Magellan ® 1000i Beep on Not on File Select for the host to beep (or not) when a not-on -file (host command) condition is detected by the host. ST ART / END PROGRAMMING BARCODES Disable Beep on Not On File Enable Beep on Not On File DEF A UL T ...

  • Datalogic Scanning 1000I - page 45

    Interface Features Product Reference Guide 3-19 AC K N A K O p t i o n s This enables/disables the ability of the scan ner to support the RS-2 32 ACK/NAK pr otocol. When configured, the scanner and/or host sends an “ ACK” when it receives data pr operly , and sends “NAK” when the data is in error . Selections for this option are: •D i s a ...

  • Datalogic Scanning 1000I - page 46

    Interface Related Features 3-20 Magellan ® 1000i RS-232 Interface Features — cont. — cont. A CK Character NAK Character ST ART / END PROGRAMMING BARCODES Sets the ACK char acter from the set of ASCII characters or an y decimal v alue from 000 to 255. P ad entr ies of less than three di gits with zeros , as in “005”. T o configure this f ea ...

  • Datalogic Scanning 1000I - page 47

    Interface Features Product Reference Guide 3-21 RS-232 Interface Features — cont. Retr y on A CK NAK T imeout Enables/disables retry after the configurable ACK NAK T imeout V alue (set in the following fea- ture ) ha s ex pire d. AC K N A K Ti m e o u t Val u e ST ART / END PROGRAMMING BARCODES Disable Retry on ACK NAK Timeout Enable Retry on ACK ...

  • Datalogic Scanning 1000I - page 48

    Interface Related Features 3-22 Magellan ® 1000i RS-232 Interface Features — cont. AC K N A K R e t r y C o u n t ST ART / END PROGRAMMING BARCODES This feature sets the number of times f or the scanner to retry a label transmi ssion under a retr y condition. 000 = No retr y 001 - 254 = Retr y f or the specified number of times 255 = Retr y f or ...

  • Datalogic Scanning 1000I - page 49

    Interface Features Product Reference Guide 3-23 RS-232 Interface Features — cont. A CK NAK Error Handling This item specifies the method the scanner will use to handle errors detect ed while waiting to receive the ACK character from the host. Errors include unrecognized host commands and com - munication errors such as parity or framing err ors. ...

  • Datalogic Scanning 1000I - page 50

    Interface Related Features 3-24 Magellan ® 1000i RS-232 Interface Features — cont. T ransmission F ailure Indication Enables/disables bad-label indication upon transmission failure. USB- OEM Inter face F eatures USB- OEM Device usage The USB-OEM protocol allows for the scanner to be identified as one of two different types of barcode scanners. D ...

  • Datalogic Scanning 1000I - page 51

    Interface Features Product Reference Guide 3-25 IBM IBM T ransm it Labels in Code 39 F ormat This feature enables/disables scanner's ability to set a symbology identifier for a specified label to Code 39 before transmitting that label data to an IBM host. This applies to: Code 128, Codabar and Code 93 for USB-OEM; Code 12 8, Codabar and Code 9 ...

  • Datalogic Scanning 1000I - page 52

    Interface Related Features 3-26 Magellan ® 1000i Wa n d E m u l a t i o n Suppor ted Symbologies The W and Emulation interface will transmit barcod e data as a wand device woul d. This inter- face will transmit the following barcode symbologies: •U P C / E A N • UPC/EAN with addons •C o d e 3 9 • F ull ASCII Code 39 • Interleaved 2 of 5 ...

  • Datalogic Scanning 1000I - page 53

    Interface Features Product Reference Guide 3-27 Wand Emulation — cont. Bar/Space P olari ty Low/H igh — Black will be transmitted as a low vo ltage level (0 to +0.7V) and space as high level (+2.4 to +5 .25V). High/Lo w — Black will be transmitted as a high v oltage level (+2.4 to +5.25V) and space as low level (0 to +0.7V). Wa n d I d l e S ...

  • Datalogic Scanning 1000I - page 54

    Interface Related Features 3-28 Magellan ® 1000i Wand Emulation — cont. Signal Speed The speed of the transmission can be set. This selects the width of the minimum narrow bar . 330 microseconds 660 microseconds T ransmit T railing Noise The transmission of noise pulses after the label may be enabled or disabled. ST ART / END PROGRAMMING BARCODE ...

  • Datalogic Scanning 1000I - page 55

    Interface Features Product Reference Guide 3-29 Wand Emulation — cont. T ransmit L eading Noise The transmission of noise pulses befor e the barcode may be enabled or disabled. Symbology C onv ersion W and Emulation can convert all barcodes to a single symbology . Choices are: No C o n ve r s i o n Convert to Code 39 Convert to Code 128 ST ART / ...

  • Datalogic Scanning 1000I - page 56

    Interface Related Features 3-30 Magellan ® 1000i Key b o a rd W ed g e and USB Ke yboard As a keyboard interface, th e sc anner supports most popular PCs and IBM term inals. The instal- lation of the wedge is a fairly simple pr ocess that doesn ’ t requir e any changes of software or hard- ware. Key bo ar d L ayo ut The Keyboard Layout option su ...

  • Datalogic Scanning 1000I - page 57

    Interface Features Product Reference Guide 3-31 Keyboard Wedge — c ont. ST ART / END PROGRAMMING BARCODES Italy Norwa y P or tugal Spain Sweden Switzerland Japan 106 K ey Hungar y Czech ...

  • Datalogic Scanning 1000I - page 58

    Interface Related Features 3-32 Magellan ® 1000i Keyboard Wedge — c ont. Caps Loc k S tat e S pecifies the format in which th e scanner sends character data. ST ART / END PROGRAMMING BARCODES Slov akia Romania Croatia P oland ³ ST ART / END PROGRAMMING BARCODES Disable Caps Lock DEF A UL T Caps Lock “ON” Shift Lock “ON” ...

  • Datalogic Scanning 1000I - page 59

    Interface Features Product Reference Guide 3-33 Keyboard Wedge — c ont. P ower-On Simulation All PCs check the keyboard status during the po wer-on S elftest. I t is recommended that y ou enable this function if you are working without a keyboard installation. I t simulates keyboard timing and passes the keyboard status to the PC during power-on. ...

  • Datalogic Scanning 1000I - page 60

    Interface Related Features 3-34 Magellan ® 1000i Con tr o l C ha r ac t er s S pecifies how the scanner transmits ASCII co ntrol characters to the host. Choices are: • Disable Contr ol Characters • Enable transmission of control characters to host • Send characters betw een 00H and 1FH acco rding to a special function-key mapping table. (Thi ...

  • Datalogic Scanning 1000I - page 61

    Interface Features Product Reference Guide 3-35 Keyboard Wedge — c ont. W edge Quie t Interval Quiet Interval is the amount of time to look fo r keyboard activity be fore the scanner breaks the keyboard connection in or der to transmit data to the host. NO TE This feature does not apply to the USB Keyboar d interface. ST ART / END PROGRAMMING BAR ...

  • Datalogic Scanning 1000I - page 62

    Interface Related Features 3-36 Magellan ® 1000i Keyboard Wedge — c ont. Intercharac ter De lay USB C OM Inter face Set-up This interface uses the Microsoft Windows USB COM driver . Before plugging your reader into the host PC, please ensure you have alr ead y copied the DLS_EUG_CDC_ACM.inf file pro- vided by Datalogic to your PC and the r eader ...

  • Datalogic Scanning 1000I - page 63

    Produc t Refe rence Gu ide 4-1 Chapter 4 Data Editing Data Editing Ov er view When a barcode is scanned, additional informatio n can be sent to the host computer along with the barcode data. This combination of barcode data and supplementary user-defined data is called a “ message string.” The features in this chapter can be used to build speci ...

  • Datalogic Scanning 1000I - page 64

    Data Editing 4-2 Magellan ® 1000i Global Pr efix/Suffix U p to 20 ASCII characters may be added as a prefix (in a position before the barcode data) and/ or as a suffix (in a position following the barcode data) as indicated in Figure 4-2 . Figure 4-2. Prefix and Suffix Positions Example: Setting a Pr efix In this example, we ’ll set a prefix for ...

  • Datalogic Scanning 1000I - page 65

    Global Prefix/Suffix Product Reference Guide 4-3 Global Prefix/Suffix — cont. ST ART / END PROGRAMMING BARCODES Sets up to 20 characters each from the set of ASCII characters or an y hex v alue from 0 to FF . T o configure this f eature, scan t he “ST ART/END” barcode abov e to place the unit in Progr amming Mode, t hen the “Set Prefix” o ...

  • Datalogic Scanning 1000I - page 66

    Data Editing 4-4 Magellan ® 1000i AIM ID AIM (Automatic I dentification Manufacturers) la bel identifiers ar e assi gned from a globally standardized list — as opposed to custom label ID characters you select y ourself — and can be included with scanned barcode data. AIM label identifiers consis t of three characters as follo ws: • A close b ...

  • Datalogic Scanning 1000I - page 67

    Label ID Product Reference Guide 4-5 Label ID A Label ID is a customizable code of up to two ASCII c haracters (00-FF), used to identify a bar- code (symbology) type. See Appendix D , Default Settings , for a listing for common symbologies. It can be appended previous to or following the transmitted barcode data depending upon how this option is en ...

  • Datalogic Scanning 1000I - page 68

    Data Editing 4-6 Magellan ® 1000i Label ID — cont. ST ART / END PROGRAMMING BARCODES Label ID T ransmission: Disable Label ID P osition: Before Bar code Data DEF A UL T Label ID P osition: After Barcode Data Set UPC-A Label ID Character(s) DEF A UL T SETTING FOR THIS FEA TURE: A ( 41 hex) DEF A UL T SET TING FOR THIS FEA TURE: A (41 hex) Set UPC ...

  • Datalogic Scanning 1000I - page 69

    Label ID Product Reference Guide 4-7 Label ID — cont. ST ART / END PROGRAMMING BARCODES DEF A UL T SETTING FOR THIS FEA TURE: E (45 hex) Set UPC-E w/P2 Addon Label ID Character(s) Set UPC-E w/P5 Addon Label ID Character(s) DEF A UL T SETTING FOR THIS FEA TURE: E (45 hex) DEF A UL T SETTING FOR THIS FEA TURE: E (45 hex) Set UPC-E w/C128 Addon Labe ...

  • Datalogic Scanning 1000I - page 70

    Data Editing 4-8 Magellan ® 1000i Label ID — cont. ST ART / END PROGRAMMING BARCODES DEF A UL T SETTING FOR THIS FEA TURE: F (46 hex) Set EAN-13 w/P2 Addon Label ID Character(s) Set EAN-13 w/P5 Addon Label ID Character(s) DEF A UL T S ETTING FOR THIS FE A TUR E: F (46 hex) DEF A UL T SETTING FOR THIS FEA TURE: F (46 hex) Set EAN-13 w/C128 Addon ...

  • Datalogic Scanning 1000I - page 71

    Label ID Product Reference Guide 4-9 Label ID — cont. ST ART / END PROGRAMMING BARCODES DEF A UL T SETTING FOR THIS FEA TURE: G8 (4738 hex) Set GTIN w/C128 addon Label ID Character(s) Set GS1 Omnidirectional Label ID Character(s) DEF A UL T SETTING FOR THIS FEA TURE: R4 (5234 hex) DEF A UL T SETTING FOR THIS FEA TURE: RX (5258 hex) Set GS1 Expand ...

  • Datalogic Scanning 1000I - page 72

    Data Editing 4-10 Magellan ® 1000i ...

  • Datalogic Scanning 1000I - page 73

    Label ID Product Reference Guide 4-11 Label ID — cont. ST ART / END PROGRAMMING BARCODES DEF A UL T SETTING FOR THIS FEA TURE: % (25 hex) Set Codabar Label ID Character(s) Set Code 93 Label ID Character(s) DEF A UL T SETTING FOR THIS FEA TURE: & ( 26 hex) DEF A UL T SETTING FOR THIS FEA TURE: @ (40 hex) Set Code 11 Label ID Character(s) Set M ...

  • Datalogic Scanning 1000I - page 74

    Data Editing 4-12 Magellan ® 1000i Case C onv ersion This feature can convert scanned barcode data to ei ther all lo wer case (a through z) or all upper case (A through Z) characters . NO TE Case con version affects ONL Y scanned barcode data, and does not affect Label ID , Prefix, Suffix, or other appended data. ST ART / END PROGRAMMING BARCODES ...

  • Datalogic Scanning 1000I - page 75

    Character Conversion Product Reference Guide 4-13 Character C on version Character conversion is an eight byte configurati on item. The eight bytes are 4 character pairs represented in hexadecimal ASCII values. The first character in the pair is the character that will be converted. The second character in the pai r is the character to conver t to. ...

  • Datalogic Scanning 1000I - page 76

    Data Editing 4-14 Magellan ® 1000i ...

  • Datalogic Scanning 1000I - page 77

    Produc t Refe rence Gu ide 5-1 Chapter 5 Sy m b o l o g i e s The scanner supports the following symbologies (barcode types). Option s for each symbology are included in this chapter . Factory Defaults— for the standard RS-232 interface are indicated in bold text throughout this section. Reference Appendix D , Default Settings for default ex cept ...

  • Datalogic Scanning 1000I - page 78

    Symbologies 5-2 Magellan ® 1000i UPC-A — continued Check Digit T ransmission Enable this option to transmit the check digit along with UPC-A barcode data. Expand UPC-A to EAN-13 Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the sym- bology ID to match those required for EAN-13. ST ART / END PROGRAMMING BARCODE ...

  • Datalogic Scanning 1000I - page 79

    UPC-A Product Reference Guide 5-3 UPC-A — continued Number Sy stem T ransmission This feature enables/disables transmission of UPC-A System N umber . UPC-A Minimum R eads This feature specifies the minimum number of consecutive times a UPC-A label must be decoded before it is accepted as good r ead. ST ART / END PROGRAMMING BARCODES Disable Numbe ...

  • Datalogic Scanning 1000I - page 80

    Symbologies 5-4 Magellan ® 1000i UPC-A — continued UPC-A In-stor e Minimum Reads This feature specifies the minimum number of co nsecutive times an in-store printed label must be decoded before it is accepted as good read. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read DEF A UL T Minimum = 2 Reads Minimum = 3 Reads Minimum = 4 Reads ...

  • Datalogic Scanning 1000I - page 81

    UPC-E Product Reference Guide 5-5 UPC-E The following options apply to the UPC-E symbology . Disable/Enable UPC-E When disabled, the scanner will not read UPC-E barcodes. Check Digit T ransmission Enable this option to transmit the check digit along with UPC-E barcode data. ST ART / END PROGRAMMING BARCODES Disab le UPC-E Enable UPC-E DEF A UL T ST ...

  • Datalogic Scanning 1000I - page 82

    Symbologies 5-6 Magellan ® 1000i UPC-E — continued Number Sy stem Digit The N u mber System D igit (NSD) which is always a zero (0) in the leading position can be optionally included (or not) with scanned barcode data. Expand to UPC-E to UPC-A Enables/disab les expansion of UPC-E l abels to UPC-A. S electing this feature also changes the symbolo ...

  • Datalogic Scanning 1000I - page 83

    UPC-E Product Reference Guide 5-7 UPC-E — continued Expand UPC-E to EAN13 Enables/disables expansion of UPC-E labels to EAN-13. Selecting this featur e also changes the symbology ID to match those required for EAN-13. Minimum Reads This feature specifies the minimum number of consecutive times a UPC-E label must be decoded before it is accepted a ...

  • Datalogic Scanning 1000I - page 84

    Symbologies 5-8 Magellan ® 1000i GTIN The following options apply to the GTIN label data format. Expand UPC/EAN to GTIN When this feature is enabled, the scanner will transl ate UPC/EAN labels to the 14 digit GTIN format. ST ART / END PROGRAMMING BARCODES Don’t Expand to GTIN DEF A UL T Expand to GTIN ...

  • Datalogic Scanning 1000I - page 85

    EAN-13 Product Reference Guide 5-9 EAN-13 The following options apply to the EAN-13 symbology . Disable/Enable EAN-13 When disabled, the scanner will not read EAN-13 barcodes. Check Digit T ransmission Enable this option to transmit the check digit along with EAN-13 barcode data. ST ART / END PROGRAMMING BARCODES Disable EAN-13 Enable EAN-13 DEF A ...

  • Datalogic Scanning 1000I - page 86

    Symbologies 5-10 Magellan ® 1000i EAN-13 — continued EAN-13 Flag 1 C haracter Enables/disables transmission of an EAN/JAN13 Flag1 character . ISBN When enabled, this feature truncates the leading three digits from labels that contain ISBN (International S tandard Book Number) and append s an ISBN check character to the end of the label. These co ...

  • Datalogic Scanning 1000I - page 87

    EAN-13 Product Reference Guide 5-11 EAN-13 — continued Minimum Reads This feature specifies the minimum number of consecutive times an EAN-13 label must be decoded before it is accepted as good r ead. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read DEF A UL T Minimum = 2 Reads Minimum = 3 Reads Minimum = 4 Reads ³ 006 0 ...

  • Datalogic Scanning 1000I - page 88

    Symbologies 5-12 Magellan ® 1000i EAN-8 The following options apply to the EAN-8 symbology . Disable/Enable EAN-8 When disabled, the scanner will not read EAN-8 barcodes. Check Digit T ransmission Enable this option to transmit the check Digit along with EAN-8 barcode data. ST ART / END PROGRAMMING BARCODES Disable EAN-8 Enable EAN-8 DEF A UL T ST ...

  • Datalogic Scanning 1000I - page 89

    EAN-8 Product Reference Guide 5-13 EAN-8 — continued Expand EAN-8 to EAN-13— Expands EAN-8 data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. Minimum Reads This feature specifies the minimum number of consecutive times an EAN-8 label must be decoded before it is accepted as g ...

  • Datalogic Scanning 1000I - page 90

    Symbologies 5-14 Magellan ® 1000i Enable EAN T wo-Label Enables/disables the ability of the scanner to decode EAN two-label pairs. ST ART / END PROGRAMMING BARCODES Disable EAN T wo-Label Enable EAN T wo-Label ...

  • Datalogic Scanning 1000I - page 91

    Add-ons Product Reference Guide 5-15 Add-ons Add-ons (or supplemental characters) are commonly added to the end of UPC/EAN barcodes. The scanner will read the add-ons if they are en abled and in the field of view . Three add-on types are supported: 2-digit, 5-digit and Code 128 add-ons. S upported options are: None— This option directs the scanne ...

  • Datalogic Scanning 1000I - page 92

    Symbologies 5-16 Magellan ® 1000i Add-ons — continued ST ART / END PROGRAMMING BARCODES Disable Optional 2-Digit Add-ons DEF A UL T Enable Optional 2-Digit Add-ons Disable Optional 5-Digit Add-ons DEF A UL T Enable Optional 5-Digit Add-ons Disable Optional Code 128 Add-ons DEF A UL T Enable Optional Code 128 Add-ons ³ 0 1101 ...

  • Datalogic Scanning 1000I - page 93

    GS1 DataBar Omnidirectional / Stacked Omni directional Product Reference Guide 5-17 GS1 DataBar Omnidirec tional / Stacked Omnidir ec tional The following options apply to the GS1 D ataBar O mnidirectional symbology . Disable/Enable GS1 DataBar Omnidire ctional When this feature is disabled, th e scanner will no t rea d GS 1 Dat aBar Om ni direc ti ...

  • Datalogic Scanning 1000I - page 94

    Symbologies 5-18 Magellan ® 1000i GS1 DataBar Omnidirectional / Stacked Omnidirectional — continued Minimum Reads This feature specifies the minimum number of consecutive times an GS1 DataBar Omnidirec- tional label must be decoded before it is accepted as good read. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read DEF A UL T Minimum = 2 Reads ...

  • Datalogic Scanning 1000I - page 95

    GS1 DataBar Expanded / Expanded Stacked Product Reference Guide 5-19 GS1 DataBar Expanded / Expanded Stacked The following options apply to the GS1 D ataBar E xpanded symbology . Disable/Enable GS1 DataBar Expanded When this feature is disabled, the scann er will not read GS1 DataBa r Expanded barcodes. GS1-128 Emulation When enabled, G S1 DataBar ...

  • Datalogic Scanning 1000I - page 96

    Symbologies 5-20 Magellan ® 1000i GS1 DataBar Expanded / Expa nded Stacked — continued Len gth Contro l Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scan ...

  • Datalogic Scanning 1000I - page 97

    GS1 DataBar Expanded / Expanded Stacked Product Reference Guide 5-21 GS1 DataBar Expanded / Expa nded Stacked — continued GS1 DataBar Expanded L ength 1, L ength 2 Progr amming I nstructions 1. Scan the ST AR T/END barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Append ix C , Alpha-Numer ic P ad and scan the three d ...

  • Datalogic Scanning 1000I - page 98

    Symbologies 5-22 Magellan ® 1000i GS1 DataBar Expanded / Expa nded Stacked — continued Minimum Reads This feature specifies the minimum number of consecutive times an GS1 DataBar Expanded label must be decoded before it is accepted as good r ead. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read DEF A UL T Minimum = 2 Reads Minimum = 3 Reads Mi ...

  • Datalogic Scanning 1000I - page 99

    GS1 DataBar Expanded / Expanded Stacked Product Reference Guide 5-23 GS1 DataBar Expanded / Expa nded Stacked — continued Co up o n Re a d Co nt r ol This feature controls coupon reading. ST ART / END PROGRAMMING BARCODES Disable coupon filtering Enable UPCA coupon decoding Disable GS1 DataBar coupon deco ding DEF A UL T Enable GS1 DataBar coupon ...

  • Datalogic Scanning 1000I - page 100

    Symbologies 5-24 Magellan ® 1000i GS1 DataBar Limited The following options apply to the GS1 DataB ar Limited symbology . Disable/Enable GS1 DataBar Limited When this feature is disabled, the scanner will not read GS1 DataBar Limited barcodes. GS1-128 Emulation When enabled, GS1 DataBar Limited barcodes will be translated to the GS1-128 label data ...

  • Datalogic Scanning 1000I - page 101

    GS1 DataBar Limited Product Reference Guide 5-25 GS1 DataBar Limited — continued Minimum Reads This feature specifies the minimum number of consecutive times an GS1 DataB ar Limited label must be decoded before it is accepted as good r ead. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read DEF A UL T Minimum = 2 Reads Minimum = 3 Reads Minimum = ...

  • Datalogic Scanning 1000I - page 102

    Symbologies 5-26 Magellan ® 1000i Co d e 3 9 The following options apply to the Code 39 symbology . Disable/Enable C ode 39 When this feature is disabled, th e scanner will not read Code 39 barcodes. Check Character Calcula tion When enabled, the scanner will calculate the check character of the labels. T urn this option on only when a checksum is ...

  • Datalogic Scanning 1000I - page 103

    Code 39 Product Reference Guide 5-27 Check Character T ransmit Enable this option to transmit the check character with scan ned barcode data. Start/Stop Characters Enables/disables transmission of Code39 start and stop characters. ST ART / END PROGRAMMING BARCODES Disable Chec k Char T ransmission Enable Check Char T ransmission DEF A UL T ST ART / ...

  • Datalogic Scanning 1000I - page 104

    Symbologies 5-28 Magellan ® 1000i Code 39 F ull ASCII Enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters . ST ART / END PROGRAMMING BARCODES Disable Code 39 Full ASCII DEF A UL T Enable Code 39 Full ASCII ...

  • Datalogic Scanning 1000I - page 105

    Code 39 Product Reference Guide 5-29 Code 39 — continued Len gth Contro l Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if th ...

  • Datalogic Scanning 1000I - page 106

    Symbologies 5-30 Magellan ® 1000i Code 39 L ength 1, Length 2 Progr amming Instruc tions 1. Scan the ST AR T/END barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Append ix C , Alpha-Numer ic P ad and scan the three digits (zero padded) r epresent- ing the length in decimal notation. 4. Scan the ST AR T/END barcode. Qu ...

  • Datalogic Scanning 1000I - page 107

    Code 39 Product Reference Guide 5-31 Code 39 — continued C ode 39 Stitching Enables/disables stitching for Code 39 labels. Wh en parts of a Code 39 barcode are presented to the scanner with this feature enabled, the barcod e parts will be assembled by the scanner’ s soft- ware, and the data will be decoded if all barcode proofing requir ements ...

  • Datalogic Scanning 1000I - page 108

    Symbologies 5-32 Magellan ® 1000i Pharmacode 39 The following options apply to the Pharmacode 39 symbology . Disable/Enable Pharmac ode 39 When this feature is disabled, the scann er will not read Pharmacode 39 barcodes. Start/Stop Characters Enables or disables transmission of Pharmacode 39 start/stop characters. ST ART / END PROGRAMMING BARCODES ...

  • Datalogic Scanning 1000I - page 109

    Pharmacode 39 Product Reference Guide 5-33 Check Character T ransmit Enable this option to transmit the check character with scan ned barcode data. ST ART / END PROGRAMMING BARCODES Disable Chec k Char T ransmission Enable Check Char T ransmission DEF A UL T ...

  • Datalogic Scanning 1000I - page 110

    Symbologies 5-34 Magellan ® 1000i C ode 128 The following options apply to the Code 128 symbology . Disable/Enable C ode 128 When this feature is disabled , the scanner will not read Code 128 barcode s. Disable/Enable EAN 128 When this feature is disabled, th e scanner will not read EAN 128 barcodes. ST ART / END PROGRAMMING BARCODES Disable Code ...

  • Datalogic Scanning 1000I - page 111

    Code 128 Product Reference Guide 5-35 Code 128 — continued T ransmit F unction Characters Enables/disables transmission of Code128 function characters 1, 2, 3, and 4. F unction codes are transmitted as follo ws: • FNC1 = 80 hex • FNC2 = 81 hex • FNC3 = 82 hex • FNC4 = 83 hex ST ART / END PROGRAMMING BARCODES Don’t T ransmit Function Cha ...

  • Datalogic Scanning 1000I - page 112

    Symbologies 5-36 Magellan ® 1000i Code 128 — continued Len gth Contro l Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the ...

  • Datalogic Scanning 1000I - page 113

    Code 128 Product Reference Guide 5-37 Code 128 — continued C ode 128 Length 1, Length 2 P rogr amming Instruct ions 1. Scan the ST AR T barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Append ix C , Alpha-Numer ic P ad and scan the three digits (zero padded) r epresent- ing the length in decimal notation. 4. Scan the ...

  • Datalogic Scanning 1000I - page 114

    Symbologies 5-38 Magellan ® 1000i Code 128 — continued Code 128 Stitching Enables/disables stitching for C ode 128 labels. When par ts of a Code 128 barcode are presented to the scanner with this feature enabled, the ba rcode parts will be assembled by the scanner’ s software, and the data will be decoded if all barcode proofing requirements a ...

  • Datalogic Scanning 1000I - page 115

    Interleaved 2 of 5 Product Reference Guide 5-39 Inte rleav ed 2 of 5 The following options apply to the I nterleaved 2 of 5 (I 2 of 5) symbo logy . Disable/Enable Interlea v ed 2 of 5 When this feature is disabled, the scann er will not read Interleaved 2 of 5 barcodes. Check D igit Cal culation When enabled, the scanner will calculate the check di ...

  • Datalogic Scanning 1000I - page 116

    Symbologies 5-40 Magellan ® 1000i Interleaved 2 of 5 — continued Check Digit T ransmit Enable this option to transmit the check digit with scanned barcode data. ST ART / END PROGRAMMING BARCODES Disable Check Digit Calculation DEF A UL T Enable Chec k Digit Calculation ...

  • Datalogic Scanning 1000I - page 117

    Interleaved 2 of 5 Product Reference Guide 5-41 Interleaved 2 of 5 — continued Len gth Contro l Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will ...

  • Datalogic Scanning 1000I - page 118

    Symbologies 5-42 Magellan ® 1000i Interleaved 2 of 5 — continued Interleav ed 2 of 5 Le ngth 1, Length 2 Pr ogramming Instructions 1. Scan the ST AR T barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Append ix C , Alpha-Numer ic P ad and scan the three digits (zero padded) r epresent- ing the length in decimal notat ...

  • Datalogic Scanning 1000I - page 119

    Interleaved 2 of 5 Product Reference Guide 5-43 Interleaved 2 of 5 — continued Interleav ed 2 of 5 Stitching Enables/disables stitching for Interleaved 2 of 5 labels. When parts of an Interleaved 2 of 5 b ar- code are presented to the scanner with this feature enabled, the barcode par ts will be assembled by the scanner’ s software, and the dat ...

  • Datalogic Scanning 1000I - page 120

    Symbologies 5-44 Magellan ® 1000i Interleaved 2 of 5 — continued Minimum Reads This feature specifies the minimum number of consecutive times an Interleaved 2 of 5 lab el must be decoded before it is accepted as good r ead. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read DEF A UL T Minimum = 2 Reads Minimum = 3 Reads Minimum = 4 Reads ...

  • Datalogic Scanning 1000I - page 121

    Codabar Product Reference Guide 5-45 Co d a b a r The following options apply to the Codabar symbology . Disable/Enable C odabar When this feature is disabled, the scann er will not read Codabar barcodes. Check Character V erification When enabled, the scanner wil l verify the check character of the labels . ST ART / END PROGRAMMING BARCODES Disabl ...

  • Datalogic Scanning 1000I - page 122

    Symbologies 5-46 Magellan ® 1000i Check Character T ransmit Enable this option to transmit the check character with scan ned barcode data. ST ART / END PROGRAMMING BARCODES Disable Chec k Char T ransmission Enable Check Char T ransmission DEF A UL T ...

  • Datalogic Scanning 1000I - page 123

    Codabar Product Reference Guide 5-47 Codabar — continued Len gth Contro l Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if th ...

  • Datalogic Scanning 1000I - page 124

    Symbologies 5-48 Magellan ® 1000i Codabar — continued C odabar Length 1, L ength 2 Progr amming I nstructions 1. Scan the ST AR T barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Append ix C , Alpha-Numer ic P ad and scan the three digits (zero padded) r epresent- ing the length in decimal notation. 4. Scan the END ...

  • Datalogic Scanning 1000I - page 125

    Codabar Product Reference Guide 5-49 Codabar — continued Start/Stop Character T ype Codabar has four pairs of S tart/Stop patterns. Select one pair to match y our application. Start/Stop Charac ter T ransmission The transmission of start and end char acters of Codabar is selected below . ST ART / END PROGRAMMING BARCODES Star t/Stop T ype: ABCD/T ...

  • Datalogic Scanning 1000I - page 126

    Symbologies 5-50 Magellan ® 1000i Start/Stop Character Match This feature enables/disables the requirem ent that start and stop characters match . Codabar Stitching Enables/disables stitching for Codabar labels. When par ts of a Codabar label are presented to the scanner with this feature enabled, the barcode parts will be assembled by the scanner ...

  • Datalogic Scanning 1000I - page 127

    Codabar Product Reference Guide 5-51 Codabar — continued Minimum Reads This feature specifies the minimum number of consecutive times a Codabar label must be decoded before it is accepted as a good read. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read DEF A UL T Minimum = 2 Reads Minimum = 3 Reads Minimum = 4 Reads ...

  • Datalogic Scanning 1000I - page 128

    Symbologies 5-52 Magellan ® 1000i Co d e 9 3 The following options apply to the Code 93 symbology . Disable/Enable C ode 93 When this feature is disabled, th e scanner will not read Code 93 barcodes. ST ART / END PROGRAMMING BARCODES Disable Code 93 DEF A UL T Enable Code 93 ...

  • Datalogic Scanning 1000I - page 129

    Code 93 Product Reference Guide 5-53 Code 93 — continued Len gth Contro l Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if th ...

  • Datalogic Scanning 1000I - page 130

    Symbologies 5-54 Magellan ® 1000i Code 93 — continued Code 93 L ength 1, Length 2 Progr amming Instruc tions 1. Scan the ST AR T barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Append ix C , Alpha-Numer ic P ad and scan the three digits (zero padded) r epresent- ing the length in decimal notation. 4. Scan the END b ...

  • Datalogic Scanning 1000I - page 131

    Code 93 Product Reference Guide 5-55 Code 93 — continued C ode 93 Stitching Enables/disables stitching for Code 93 barcodes. When par ts of a Code 93 label are presented to the scanner with this feature enabled, the barcod e parts will be assembled by the scanner’ s soft- ware, and the data will be decoded if all barcode proofing requir ements ...

  • Datalogic Scanning 1000I - page 132

    Symbologies 5-56 Magellan ® 1000i MSI/Plessey The following options apply to the MSI/Plessey symbology . Disable/Enable MSI/Plessey When this feature is disabled, th e scan ner will not read MSI/Plessey barcodes. Check Digit V erification This feature specifies whether one or two check digits are to be calculat ed and verified. ST ART / END PROGRA ...

  • Datalogic Scanning 1000I - page 133

    MSI/Plessey Product Reference Guide 5-57 MSI/Plessey — continued Check Digit T ransmit When this option is enabled, the scanner will transmit one-digit or two-digit check digits, depending upon the setting for check digit verification. Number of Check Char acters S pecifies number of MSI/Plessey check characters to be calculated and verified ST A ...

  • Datalogic Scanning 1000I - page 134

    Symbologies 5-58 Magellan ® 1000i MSI/Plessey — continued Len gth Contro l Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if ...

  • Datalogic Scanning 1000I - page 135

    MSI/Plessey Product Reference Guide 5-59 MSI/Plessey — continued MS I/ Ple ss ey Len gth 1 , Len gt h 2 Progr amming Instruc tions 1. Scan the ST AR T barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Append ix C , Alpha-Numer ic P ad and scan the three digits (zero padded) r epresent- ing the length in decimal notati ...

  • Datalogic Scanning 1000I - page 136

    Symbologies 5-60 Magellan ® 1000i MSI/Plessey — continued MSI/Plessey S titching Enables/disables stitching for MSI/Plessey barc odes. When parts of an MSI/Ple ssey label ar e presented to the scanner with this feature enable d, the barcode parts will be assembled by the scanner’ s software, and the data will be decoded if all barcode proofing ...

  • Datalogic Scanning 1000I - page 137

    MSI/Plessey Product Reference Guide 5-61 MSI/Plessey — continued Minimum Reads This feature specifies the minimum number of consecutive times an MSI/Ples sey label must be decoded before it is accepted as good r ead. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read DEF A UL T Minimum = 2 Reads Minimum = 3 Reads Minimum = 4 Reads ...

  • Datalogic Scanning 1000I - page 138

    Symbologies 5-62 Magellan ® 1000i Standar d 2 of 5 The following options apply to the S tandard 2 of 5 symbology . Disable/Enable Standard 2 of 5 When this feature is disabled, th e scanne r will not read S tandard 2 of 5 barcodes. Check Digit V erification When enabled, the scanner wil l verify the check digit of the label s. ST ART / END PROGRAM ...

  • Datalogic Scanning 1000I - page 139

    Standard 2 of 5 Product Reference Guide 5-63 Standard 2 of 5 — continued Check Digit T ransmit When this option is enabled, the scanner will transmit the check digit. ST ART / END PROGRAMMING BARCODES Disable Chec k Digit T ransmission Enable Check Digit T ransmission DEF A UL T ...

  • Datalogic Scanning 1000I - page 140

    Symbologies 5-64 Magellan ® 1000i Standard 2 of 5 — continued Len gth Contro l Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode ...

  • Datalogic Scanning 1000I - page 141

    Standard 2 of 5 Product Reference Guide 5-65 Standard 2 of 5 — continued Standard 2 of 5 L ength 1, Length 2 P rogr amming Instruc tions 1. Scan the ST AR T barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Append ix C , Alpha-Numer ic P ad and scan the three digits (zero padded) r epresent- ing the length in decimal ...

  • Datalogic Scanning 1000I - page 142

    Symbologies 5-66 Magellan ® 1000i Standard 2 of 5 — continued Stand ard 2 of 5 Stitchi ng Enables/disables stitching for Standar d 2 of 5 ba rcodes. When parts of a S tandard 2 of 5 label are presented to the scanner with this feature enabled, the barcode par ts will be assembled by the scanner’ s software, and the data will be decoded if all ...

  • Datalogic Scanning 1000I - page 143

    Standard 2 of 5 Product Reference Guide 5-67 Standard 2 of 5 — continued Minimum Reads This feature specifies the minimum number of c onsecutive times a Standard 2 of 5 label must be decoded before it is accepted as good r ead. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read DEF A UL T Minimum = 2 Reads Minimum = 3 Reads Minimum = 4 Reads ...

  • Datalogic Scanning 1000I - page 144

    Symbologies 5-68 Magellan ® 1000i ...

  • Datalogic Scanning 1000I - page 145

    Produc t Refe rence Gu ide 6-1 2D S ymbologies & Advanc ed Decoding Fe a t u r e s NO TE The features in this section are a vailab le ONL Y for models with 2D features activated. ...

  • Datalogic Scanning 1000I - page 146

    2D Symbologies & Advanced Decoding Features 6-2 Magellan ® 1000i 2D Symbologies The scanner supports the following 2D symbologies (barcode types): PDF 417 and Datamatrix . Options for each symbology are included in this addendum. Factory Defaults— for the std. RS-232 interface are indicated in bold text thr oughout. PDF 417 Disable/Enable PD ...

  • Datalogic Scanning 1000I - page 147

    2D Symbologies Product Reference Guide 6-3 PDF 417 — continued Leng th Cont rol Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode ...

  • Datalogic Scanning 1000I - page 148

    2D Symbologies & Advanced Decoding Features 6-4 Magellan ® 1000i PDF 417 — continued PDF 417 Length 1, Length 2 Pr ogramming Instructions 1. Scan the ST AR T barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Alpha-Numer ic P ad and scan the four hex digits repr esenting the length in hexi dec- imal notation. Scan ...

  • Datalogic Scanning 1000I - page 149

    2D Symbologies Product Reference Guide 6-5 PDF 417 — continued Minimum Reads This feature specifies the minimum number of consecutive times a PDF 417 label must be decoded before it is accepted as good r ead. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read Minimum = 2 Reads Minimum = 3 Reads Minimum = 4 Reads ...

  • Datalogic Scanning 1000I - page 150

    2D Symbologies & Advanced Decoding Features 6-6 Magellan ® 1000i Datamatrix Disable/Enable Datamatrix When disabled, the scanner will not read Datamatrix barcodes. ST ART / END PROGRAMMING BARCODES Disable Datamatrix Enable Datamatrix ...

  • Datalogic Scanning 1000I - page 151

    2D Symbologies Product Reference Guide 6-7 Datamatrix — continued Leng th Cont rol Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barc ...

  • Datalogic Scanning 1000I - page 152

    2D Symbologies & Advanced Decoding Features 6-8 Magellan ® 1000i Datamatrix — continued Datamatrix L ength 1, Length 2 Pr ogramming Instr uctions 1. Scan the ST AR T barcode. 2. Scan either the Set Length 1 or Set Length 2 bar code. 3. T urn to Alpha-Numer ic P ad and scan the four hex digits repr esenting the length in hexi dec- imal notati ...

  • Datalogic Scanning 1000I - page 153

    2D Symbologies Product Reference Guide 6-9 Datamatrix — continued Minimum Reads This feature specifies the minimum number of consecutive times a Datamatrix label must be decoded before it is accepted as good r ead. ST ART / END PROGRAMMING BARCODES Minimum = 1 Read Minimum = 2 Reads Minimum = 3 Reads Minimum = 4 Reads ...

  • Datalogic Scanning 1000I - page 154

    2D Symbologies & Advanced Decoding Features 6-10 Magellan ® 1000i Image Capture How t o Capture an Image T o initiate an Image Captur e, scan the IMAG E CAPTURE label below , and press the button. A targeting “ pointer ” will be illuminated while the button is pressed. U pon release of the button, the image is captured and transmitted to t ...

  • Datalogic Scanning 1000I - page 155

    Produc t Refere nce Guid e A-1 Chapter A Pr oduc t Specifications Optical and Read P er formanc e P aramet ers Scanner Dimensions Pa rameter Specification Scan V olume 70 cubic inches Scan P attern 100 lines Scan Rate 1,100 digital scan lines Minimum Resolution 5 mil Depth of Field (100% UPC Labels) 0 - 6” Minimum Print Contrast Ratio 25% Ske w ( ...

  • Datalogic Scanning 1000I - page 156

    A-2 Magellan ® 1000i Ph ysical Pr oper ties Electrical Par ameters Environ ment al Param eter s Other Para meters Pa rameter Specification Dimensions (Scanner onl y): 3.3” x2.8” x3.7” Dimensions (Scanner w/Base Station): 5.5” x2.9” x3.8” We ight (Scanner) 7.0 oz. We ight (Base Station) 6.6 oz. Pa rameter Specification Operating V oltag ...

  • Datalogic Scanning 1000I - page 157

    Produc t Refere nce Guid e B-1 Chapter B Ca b l e Pi n ou t s Stan dard Cab le Pi nouts (P rimar y Inter face Cables) RS-232 IBM P or t 5B/9B/17 1 2C T S 3 4R T S 5R X D 6T X D 7 8 VCC IN 9G N D 10 1 2 3 4D A T A - 5 6D A T A + 7 8V C C _ I N 9G N D 10 Pin 1 10 Position RJ (Scanner End) Pin 1 10 Position RJ (Scanner End) ...

  • Datalogic Scanning 1000I - page 158

    Cable Pinouts B-2 Magellan ® 1000i USB- OEM USB, USB K eyboard & USB C OM Wa n d E m u l a t i o n Key b o a rd W ed g e 1 2 3 4D - 5 6D + 7 8V I N 9G N D 10 1 2 3 4D - 5 6D + 7 8 VBUS_VIN 9G N D 10 1 2 3 W AND~ 4 5 6 7 8V C C _ I N 9G N D 10 1 2 KB_D A T A 3A T _ C L K 4 KB_CLK 5 6A T _ D A T A 7 8V C C _ I N 9G N D 10 Pin 1 10 Position RJ (S ...

  • Datalogic Scanning 1000I - page 159

    Produc t Refere nce Guid e C-1 Chapter C Alpha-Numeric Pad A B C D E F ...

  • Datalogic Scanning 1000I - page 160

    C-2 Magellan ® 1000i Alpha-Numeric Pad 1 2 3 0 9 8 7 6 5 4 ...

  • Datalogic Scanning 1000I - page 161

    Produc t Refere nce Guid e D-1 Appendix D Default Settings Defaults by S ymbology The following is a partial list of key settings for each symbology type. Code T ype Read Enable Checksum V erification Enable Checksum T ransmission Enable Label ID UPC-A ✓✓ ✓ A UPC-E ✓✓ ✓ E EAN-13 ✓✓ ✓ F EAN-8 ✓✓ ✓ FF GS1 DataBar Omnidire ctio ...

  • Datalogic Scanning 1000I - page 162

    D-2 Magellan ® 1000i Inte r face Default Ex ceptions The factory defaul t settings indicated in the programming sections (in bold text) reflect factory configuration for the RS-232 standard interface. The follo wing tables list de fault exceptions by interface for the remaining available interfaces. IBM Inte r faces IBM Interfaces include USB-OEM, ...

  • Datalogic Scanning 1000I - page 163

    Interface Default Exceptions Product Referenc e Guide D-3 Interface Default Exceptions — continued RS-232 Winc or/Nix dor f Parameter Default Setting Interf ace T ype RS-232-WN Number of Host T ransmit Buff ers One Buffer RS-232 P arity Odd RS-232 Hardware Control CTS Flow Control UPC-E Check Character Con version Disabled UCC/EAN-128 Label ID ? ...

  • Datalogic Scanning 1000I - page 164

    D-4 Magellan ® 1000i Interface Default Exceptions — continued Wa n d E m u l a t i o n Key b o a rd s Keyboard interfaces include USB Keyboard and Keyboard W edge A-Y. Parameter Default Setting Interf ace T ype W and Emulation Code 39 Star t/Stop Character T ransmission Enable Parameter Default Setting K eyboard W edge Interface T ype USB Ke ybo ...

  • Datalogic Scanning 1000I - page 165

    Produc t Refere nce Guid e E-1 Appendix E K eyboard F unc tion K ey Mappings K eyboard Model Cr oss Refer ence Ta b l e E - 1 summarizes the keyboard models, their defined protoc ol, scancode set, and some unique featu res. The remaining tables in this chapter pro vide the function key maps associated with each of the scanc ode sets. Table E-1. Key ...

  • Datalogic Scanning 1000I - page 166

    E-2 Magellan ® 1000i Table E-2. Scanset 1 Function K ey Map Table E-3. Scanset 2 Function K ey Map ASCII (hex) ASCII code K ey Scancode 00 NUL AL T right Make E0h 38h 01 SOH AL T right Break E0h B8h 02 STX AL T left Make 38h 03 ETX AL T left Break B8h 04 EO T CTRL left Mak e 1Dh 05 ENQ CTRL left Break 9Dh 06 A CK CTRL right Mak e E0h 1Dh 07 BEL CT ...

  • Datalogic Scanning 1000I - page 167

    Keyboard Model Cross Reference Product Referenc e Guide E-3 Table E-4 . Scanset 3, 102-Key Fu nction Key Map 1B ESC ESC 76h 1C FS F7 83h 1D GS F8 0Ah 1E RS F9 01h 1F US F10 09h ASCII (hex) ASCII code Ke y Scancode 00 NUL AL T r ight Make 39h 01 SOH AL T right Break F0h 39h 02 STX AL T left Make 19h 03 ETX AL T left Break F0h 19h 04 EO T CTRL left M ...

  • Datalogic Scanning 1000I - page 168

    E-4 Magellan ® 1000i Table E-5. Scanset 3 122-Key Funct ion Key Map ASCII (hex) ASCII code Key Scancode 00 NUL AL T Right Make 39h 01 SOH AL T Right Break F0h 39h 02 STX AL T left Make 19h 03 ETX AL T left Break F0h 19h 04 EO T CTRL left (RESET) Make only 11h 05 ENQ CTRL left (RESET) Make/Break 11h F0h 11h 06 A CK ONLINE Enter Make only 58h 07 BEL ...

  • Datalogic Scanning 1000I - page 169

    Keyboard Model Cross Reference Product Referenc e Guide E-5 Table E-6. Japanese DOS Function Key Map ASCII value ASCII code Key Scancode 00h NUL AL T right Make 31h 01h SOH AL T r ight Break B1h 02h STX AL T left Make 31h 03h ETX AL T left Break B1h 04h EOT CTRL left Mak e 41h 05h ENQ CTRL left Break C1h 06h ACK CTRL right Make 41h 07h BEL CTRL r i ...

  • Datalogic Scanning 1000I - page 170

    E-6 Magellan ® 1000i Table E-7. NEC 98 01-Key Function K ey Map ASCII value ASCII code Ke y Scancode 00h NUL unused n/a 01h SOH CR 1Ch 02h STX CAPS LOCK ON (make) 71h 03h ETX CAPS LOCK OFF (break) F1h 04h EO T CTRL left Make 74h 05h ENQ CTRL left Break F4h 06h A CK CTRL-C 60h 07h BEL n/a n/a 08h BS BS 0Eh 09h HT T AB right 0Fh 0Ah LF RIGHT arrow ( ...

  • Datalogic Scanning 1000I - page 171

    Produc t Refere nce Guid e F-1 Chapter F Host C ommands Ac cepting RS-232 Commands The scanner responds to the following RS-232 commands: If one of the abo ve commands is received, the scanner wi ll perform the steps indicated for the command. Host commands for other interfaces are also availa ble. Contact T e ch S upport for more details. COMMAND ...

  • Datalogic Scanning 1000I - page 172

    F-2 Magellan ® 1000i NO TES ...

  • Datalogic Scanning 1000I - page 173

    Produc t Refere nce Guid e G-1 Chapter G Sam ple S ym bo ls 0 1234567890 1234567890 Code 128 9 780330 290951 BC321 123456-9$ 123456 UPC-A Code 128 Code 39 Code 93 Interleav ed 2 of 5 EAN-13 Code 2 of 5 A13579B Codabar 05 ...

  • Datalogic Scanning 1000I - page 174

    G-2 Magellan ® 1000i Sample Symbols (01)00123456789012 GS1 DataBar Omni- 0100123456789050 GS1 DataBar Expanded ...

  • Datalogic Scanning 1000I - page 175

    ASCII Char t ASCII Char . Hex No . ASCII Char . Hex No. AS CII Char . Hex No. AS CII Char . He x No . NUL SOH STX ETX EO T ENQ AC K BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F SP ! “ # $ % & ’ ( ) * + , ...

  • Datalogic Scanning 1000I - page 176

    Au st ra li a Datalogic Scanning Pt y Ltd T elephone: [61] (2) 9870 3200 australia.scanning@datalogic.com Fra n c e a n d B e n e l u x Datalogic Scanning Sarl T elephone: [33].01.64.86.71.00 france.scanning@datalogic .com German y Datalogic Scanning GmbH T elephone: 49 (0) 61 51/93 58-0 germany .scanning@datalogic.com India Datalogic Scanning I nd ...

Manufacturer Datalogic Scanning Category Barcode Reader

Documents that we receive from a manufacturer of a Datalogic Scanning 1000I can be divided into several groups. They are, among others:
- Datalogic Scanning technical drawings
- 1000I manuals
- Datalogic Scanning product data sheets
- information booklets
- or energy labels Datalogic Scanning 1000I
All of them are important, but the most important information from the point of view of use of the device are in the user manual Datalogic Scanning 1000I.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Datalogic Scanning 1000I, service manual, brief instructions and user manuals Datalogic Scanning 1000I. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Datalogic Scanning 1000I.

Similar manuals

A complete manual for the device Datalogic Scanning 1000I, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Datalogic Scanning 1000I by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Datalogic Scanning 1000I.

A complete Datalogic Scanning manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Datalogic Scanning 1000I - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Datalogic Scanning 1000I, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Datalogic Scanning 1000I, that we can find in the current document
3. Tips how to use the basic functions of the device Datalogic Scanning 1000I - which should help us in our first steps of using Datalogic Scanning 1000I
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Datalogic Scanning 1000I
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Datalogic Scanning 1000I in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Datalogic Scanning 1000I?

Use the form below

If you did not solve your problem by using a manual Datalogic Scanning 1000I, ask a question using the form below. If a user had a similar problem with Datalogic Scanning 1000I it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)