English dropdown-ico

Manual Jet Tools JDP-17MF

24 pages 1.54 mb
Download

Go to site of 24

Summary
  • Jet Tools JDP-17MF - page 1

    Operating Instructions and Parts Manual 17” Drill Press Model JDP-17MF WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-354169 Ph.: 800-274-6848 Revision C1 01/06 www.wmhtoolgroup.com Copyri ght © WMH Tool Group This Manual is Bookmarked ...

  • Jet Tools JDP-17MF - page 2

    2 This manual has been prepared for the owner and operat ors of a JDP-17MF Drill Press. Its purpose, aside from machine operation, is to promote safe ty through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life a ...

  • Jet Tools JDP-17MF - page 3

    3 , WARNING Wear eye protection. Alw ays keep guards in place and in proper operating condition. Do not operate the machine w ithout the guards for any reason. Support w orkpiece adequately at all times during opera tion; maintain control of w ork at all times. This drill press is designed and intended for use by properly trained and experienced pe ...

  • Jet Tools JDP-17MF - page 4

    4 • USE RECOMMENDED ACCESSORIES . The use of accessories and attachments not recommended by JET may cause hazards or risk of injury to persons. • NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped. • CHECK DAMAGED PARTS. Before further use of the machine, a guard or other part that is damaged should be carefully che ...

  • Jet Tools JDP-17MF - page 5

    5 Grounding Instructions Caution: This tool must be grounded w hile in u se to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. Th is tool is equipped with an electric cord having an equipment-grounding condu ...

  • Jet Tools JDP-17MF - page 6

    6 230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the pow er source. 2. This JET drill press is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure ...

  • Jet Tools JDP-17MF - page 7

    7 On-Off Switch Padlock Model No. BP-1, Stock No. 709736 To safeguard your machine from unauthorized operat ion and to avoid accidental starting by young children, the use of a padlock is highly recommended. JET model BP-1 is available from your local authorized JET distributor or by calling WMH Tool Group at 800-274-6848. To lock out an on-off swi ...

  • Jet Tools JDP-17MF - page 8

    8 Specifications: JDP-17MF Stock Nu mber ................................................................................................................... .................. 354169 Swing.......................................................................................................................... ..........................16-1/2” Typ ...

  • Jet Tools JDP-17MF - page 9

    9 Contents of the Shipping Container 1. Head Assembly 1. Table 1. Column and Bracket Assembly 1. Base 1. Owner’s Manual 1. Warranty Registration Card 1. Chuck and Chuck Key 3. Downfeed Handle 1. Table Bracket Lock Handle 1. Table Bracket Raising Handle 4. M10 x 40 Hex Cap Bolts 1. Arbor 1. Drift Key Tools Supplied for Assembly 1. 3mm Hex Wrench 1 ...

  • Jet Tools JDP-17MF - page 10

    10 Assembly 1. Place the base (A, Fig. 1) on a level floor. 2. With a 17mm wrench attach the column assembly (B, Fig. 1) to the base (A, Fig. 1) with four M10 x 40 hex cap bolts (C, Fig. 1). Tighten firmly. 3. Thread lock handle (D, Fig. 2) into the table bracket (E, Fig. 2). 4. Loosen the set screw (F, Fig. 3) on the raising handle (G, Fig. 3) wit ...

  • Jet Tools JDP-17MF - page 11

    11 9. With the aid of a second person, carefully lift the head onto the column top. Caution: The head assembly is heavy ! Use care w hen lifting onto the column! 10. Rotate head assembly until sides of the belt cover are parallel with the sides of the base. 11. Tighten two set screws (A, Fig. 4) with a 5mm wrench until they are snug. 12. Install th ...

  • Jet Tools JDP-17MF - page 12

    12 Adjusting the Depth Stop To drill multiple holes at the same preset depth, use the depth stop: 1. Use a pencil to mark the depth the bit will drill into the workpiece (A, Fig. 7). 2. With the drill bit in the chuck, lower down feed handle to advance bit to your mark,see Figure 7. 3. With your other hand, advance the lock nuts (B, Fig. 7) on the ...

  • Jet Tools JDP-17MF - page 13

    13 Speed & Pulley Chart ...

  • Jet Tools JDP-17MF - page 14

    14 Return Spring Adjustment The return spring is adjusted at the factory and should not need further adjustment. If adjustment is deemed necessary: 1. Unplug the machine from the power source. 2. Loosen two jam nuts (A, Fig. 9). Do not remove. 3. Firmly hold the coil spring cover (B, Fig. 9). 4. Pull out the cover and rotate until the pin (C, Fig. ...

  • Jet Tools JDP-17MF - page 15

    15 Basic Operation • Always use a back-up piece of scrap wood to cover the table. This protects both the table and the drill bit. • Place material to be drilled in such as way as to come into contact with the left side of the column. This prevents the material from spinning. , WARNING! If the w ork piece is not large enough to come into contact ...

  • Jet Tools JDP-17MF - page 16

    16 Troubleshooting Trouble Probable Cause Remedy Drill press w ill not start. 1. Drill press unplugged from wall, or motor. 2. Fuse blown, or circuit breaker tripped. 3. Cord damaged. 4. Starting capacitor bad. 1. Check all plug connections. 2. Replace fuse, or reset circuit breaker. 3. Replace cord. 4. Replace starting capacitor. Drill press does ...

  • Jet Tools JDP-17MF - page 17

    17 Parts Breakdown for JDP-17MF ...

  • Jet Tools JDP-17MF - page 18

    18 Parts List for JET JDP-17MF Drill Press Index Part No. No. Description Size Qty. 1 .......... 10600111 ...................... Base ..................................................................... .................................... 1 2A ........ 12909001A1 .................. Colu mn and Holder Assy. .................................... ... ...

  • Jet Tools JDP-17MF - page 19

    19 Index Part No. No. Description Size Qty. 61 ........ BB-6203Z ...................... Ball Bearing .......................................................... ................. ................... 1 62 ........ 10606201 ...................... Washer ................................................................. ................ ................ ...

  • Jet Tools JDP-17MF - page 20

    20 Index Part No. No. Description Size Qty. 169 ...... 11316904 ...................... Nameplate ............................................................ ................... ................. 1 601 ...... TS-1533032 .................. Pan Head Machine Sc rew ................................... M5x10 ......................... 2 602 ...... 2504MZ ...

  • Jet Tools JDP-17MF - page 21

    21 ...

  • Jet Tools JDP-17MF - page 22

    22 ...

  • Jet Tools JDP-17MF - page 23

    23 ...

  • Jet Tools JDP-17MF - page 24

    24 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com ...

Manufacturer Jet Tools Category Drill

Documents that we receive from a manufacturer of a Jet Tools JDP-17MF can be divided into several groups. They are, among others:
- Jet Tools technical drawings
- JDP-17MF manuals
- Jet Tools product data sheets
- information booklets
- or energy labels Jet Tools JDP-17MF
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jet Tools JDP-17MF.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jet Tools JDP-17MF, service manual, brief instructions and user manuals Jet Tools JDP-17MF. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jet Tools JDP-17MF.

Similar manuals

A complete manual for the device Jet Tools JDP-17MF, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jet Tools JDP-17MF by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jet Tools JDP-17MF.

A complete Jet Tools manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jet Tools JDP-17MF - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jet Tools JDP-17MF, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jet Tools JDP-17MF, that we can find in the current document
3. Tips how to use the basic functions of the device Jet Tools JDP-17MF - which should help us in our first steps of using Jet Tools JDP-17MF
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jet Tools JDP-17MF
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jet Tools JDP-17MF in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jet Tools JDP-17MF?

Use the form below

If you did not solve your problem by using a manual Jet Tools JDP-17MF, ask a question using the form below. If a user had a similar problem with Jet Tools JDP-17MF it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)