English dropdown-ico

Manual Light & Motion VX2000

17 pages 0.84 mb
Download

Go to site of 17

Summary
  • Light & Motion VX2000 - page 1

    Owner’ s Manual www .uwimaging.com VX2000 Bluefin ...

  • Light & Motion VX2000 - page 2

    3 T able of Contents Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Bluefin VX2000 Operation - Camera Preparation . . . . . . . . . . . . . . . . . . . . . . . . . .6 Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Light & Motion VX2000 - page 3

    5 Quick Start Guide Every Light & Motion housing is pr essure tested prior to shipping. However , unseen damage may have occurred during shipping. It is str ongly recommended to test dive with only the housing prior to installing the camcorder . 1) Attach a fully charged Sony NP-750 battery to the camcorder . Install a Mini DV tape and a Memory ...

  • Light & Motion VX2000 - page 4

    7 Operation The Bluefin VX2000 is designed to access most camcorder featur es using a combination of infrared commands from the Smart Grips as well as mechanical interfaces on the housing. Rear Plate ON/MODE - T urns camcorder on from off state. When camcorder is in power ed state, loops between Camera - Memory and VTR modes. Program/Gain - Activat ...

  • Light & Motion VX2000 - page 5

    8 9 Using the Bluefin VX2000 in Camcorder mode Camcorder POWER switch should be set to MEMORY setting when installed into the housing. When the rear plate is secured to the housing, the camcorder will switch to CAM mode. Left Smart Grip (ref. fig. 9) LIGHTS - After initial power up from battery pod, cycles lights through output cycles. Press and ho ...

  • Light & Motion VX2000 - page 6

    Using the Bluefin VX2000 in VTR mode Left Grip (ref. fig. 1 1) F AR/- Frame Back while paused and r everse direction during playback NEAR/+ Frame Advance while paused PHOTO DIS. - Rewind during Stop and high speed reverse during Playback LIGHTS - Not used PHOTO - Captures still image to Memory Stick Right Grip (ref. fig. 12) TELE - Stop WIDE - Slow ...

  • Light & Motion VX2000 - page 7

    Housing Storage Store housing and T ravel Case in a dry location. 24 hours after a dive, leave the Rear Plate off the housing to allow for air circulation. Similarly , leave T ravel Case Lid about two inches open. Allow any r esidual water to evaporate from the T ravel Case prior to storing the housing. 12 13 Front Optic Installation / Removal T o ...

  • Light & Motion VX2000 - page 8

    Using Manual Focus The Bluefin VX2000 F AR/-, NEAR/+ and MOM.AF buttons will switch the camcorder from auto to manual focus. One technique is to toggle the F AR and NEAR buttons until the subject is in focus. Because this method is slow , we recommend the following technique. 1) While in auto focus, point the camera toward a solid object equidistan ...

  • Light & Motion VX2000 - page 9

    Bluefin VX2000 Lights - Getting Started Pictured below are the components of both the SunRay -X Pr o and the SunRay -X Elite lighting systems. T ake a moment to familiarize yourself with each part for later identification and use. Battery Pods Pro light heads Charger and electrical cord Light Arms Light Cable NiMH Batteries 16 6) Press the Handle C ...

  • Light & Motion VX2000 - page 10

    19 18 Removing Batteries 1) Rotate latch at the front of the pod counter -clockwise 1/8 turn or until it stops. 2) Pull the front cap of f the pod. 3) Pull the battery from the pod using removal strap (r ef. fig. 17 & 18). Mounting Batter y Pods Battery Pods can be mounted prior to installing batteries into pods. 1) Remove the rear plate or mon ...

  • Light & Motion VX2000 - page 11

    21 20 Assembly with Universal Mounts Mounting Arm to Light Heads Align top of arm with arm light head base and press FIRML Y together . Arm should snap into position. (ref. fig. 25). Removing Arm from Light Heads T o remove light head from arm, “break” the arm at the upper most joint. Applying pr essure on the Light Arm and not the Light Head ( ...

  • Light & Motion VX2000 - page 12

    23 22 Light Operation Before you turn on the Pro lights, verify that the mode selector (flat position of black ring around red power button) is set to the P setting. Before you turn on the Elite lights, verify that the mode selector (flat position of black ring around red power button) is set to the E setting. Operation with SunRay-X Pro Lighting S ...

  • Light & Motion VX2000 - page 13

    25 24 Bluefin Bulkhead Installation 1) Remove the Rear Plate. 2) Locate the power switch on the circuit boar d on the inside of the Rear Plate. Switch the appropriate switch (upper or lower) to ON. This activates power to the bulkhead. (ref. fig. 29) 3) Using a flat head screwdriver or coin, remove the Port Plug (r ef. fig. 30) 4) On the inside of ...

  • Light & Motion VX2000 - page 14

    Bluefin Compact Monitor ID and Operation The External Monitor consists of three components • External Monitor - provides a 2.5” image of camera view • Clamp assembly - mounts monitor to back of housing • Cable - provides video signal from housing to External Monitor 1) Install monitor by first attaching clamp assembly to back of monitor . 2 ...

  • Light & Motion VX2000 - page 15

    Diving Without a Monitor Attached If you do not use the monitor you MUST de-activate power to the bulkhead before entering the water . T o de-activate Bluefin bulkhead: 1) Remove the Rear Plate 2) Locate the on/off switch on the inside of the Rear Plate. 3) Switch appropriate bulkhead to of f position. Power On/Off with Remote Monitor On - When cam ...

  • Light & Motion VX2000 - page 16

    31 30 Returning Products for Care W e highly recommend a factory annual service to maintain proper operation of your Bluefin Housing. 1) Before returning your Light & Motion product for care, please call or email our service department for a RMA number . 2) Ship your product pre-paid freight with the return number printed on the outside of the ...

  • Light & Motion VX2000 - page 17

    905-0187-A 300 Canner y Row • Monterey , CA 93940 (831) 645-1525 • Fax (831) 375-2517 www .uwimaging.com ...

Manufacturer Light & Motion Category Camcorder

Documents that we receive from a manufacturer of a Light & Motion VX2000 can be divided into several groups. They are, among others:
- Light & Motion technical drawings
- VX2000 manuals
- Light & Motion product data sheets
- information booklets
- or energy labels Light & Motion VX2000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Light & Motion VX2000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Light & Motion VX2000, service manual, brief instructions and user manuals Light & Motion VX2000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Light & Motion VX2000.

Similar manuals

A complete manual for the device Light & Motion VX2000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Light & Motion VX2000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Light & Motion VX2000.

A complete Light & Motion manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Light & Motion VX2000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Light & Motion VX2000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Light & Motion VX2000, that we can find in the current document
3. Tips how to use the basic functions of the device Light & Motion VX2000 - which should help us in our first steps of using Light & Motion VX2000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Light & Motion VX2000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Light & Motion VX2000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Light & Motion VX2000?

Use the form below

If you did not solve your problem by using a manual Light & Motion VX2000, ask a question using the form below. If a user had a similar problem with Light & Motion VX2000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)