English dropdown-ico

Manual Fresco Speaker

20 pages 1.09 mb
Download

Go to site of 20

Summary
  • Fresco Speaker - page 1

    F RESCO ™ i user ’s manual M A RTIN L OGA N the loudspeaker technology company ® ...

  • Fresco Speaker - page 2

    2 Contents & Introduction C ONTENTS AND I NTRODUCTION Contents and Introduction . . . . . . . . . . . . . . . . . . . 2 Contents Introduction Installation in Brief . . . . . . . . . . . . . . . . . . . . . . . . 3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Signal Connection On W all/Off W all Switch Break -In Moun ...

  • Fresco Speaker - page 3

    Installation in Brief 3 I NST ALLA TION IN B RIEF W e know you are eager to hear your new F resco i loudspeaker , so this section is provided to allow fast and easy set up. Once you have it operational, please take the time to read, in depth, the rest of the information in this manual. It will give you perspective on how to attain the greatest poss ...

  • Fresco Speaker - page 4

    Use the best speaker cables you can. The length and type of speaker cable used in your system will have an audible effect. Under no circumstance should a wire of gauge higher (thinner) than #16 be used. In general, the longer the length used, the greater the necessity of a lower gauge, and the lower the gauge, the better the sound. A variety of spe ...

  • Fresco Speaker - page 5

    NOTE: MartinLogan recommends using 5 wall anchors to secure each F resco i to a wall. During the installation, if any of the screw/wall anchor positions are over a stud, it is recommended to screw directly into the stud. NOTE: T o assure that your F resco i is safely wall mounted, these instructions must be carefully followed. Study them thoroughly ...

  • Fresco Speaker - page 6

    6 Mounting the Fresco i On A Wall or Ceiling NOTE: F resco i’s bracket assembly consists of two main parts: the wall bracket (attaches to the wall) and the cabinet bracket (attaches to the F resco i). When correctly configured the wall and cabinet brackets should each have one pin installed—the wall bracket with an upward pointing pin in the up ...

  • Fresco Speaker - page 7

    Mounting the Fresco i On A Wall or Ceiling 7 Changing the Direction of R otation Figure 7. Remove the 2 cap nuts and washers from the hinges. Figure 8. Remove the wall bracket from the cabinet bracket. Figure 9. Remove the 2 set screws. Figure 10. Change hinge pin locations. Figure 11. Reinstall the two set screws to hold hinge pins in place. Requi ...

  • Fresco Speaker - page 8

    8 Mounting the Fresco i On A Wall or Ceiling Required hardware (included): (6) M4 screws Required tools (included): 2.5mm Allen tool 1 P repare a flat surface with padding and sheets to protect the speaker as you work on it. R emove the F resco i's grill cloth and carefully place the F resco i face down on the work surface. 2 Using the 6mm All ...

  • Fresco Speaker - page 9

    Required hardware (included): (5) wall anchors (5) 1" Phillips head wood screws Required tools (included): 6mm Allen tool Required tools (not included): Lev el Electric drill and 1 / 4 " and 1 / 8 " drill bits Phillips screwdriver 1 Hold the F resco i at the mounting location. Examine the location to assure the wall is free of obstru ...

  • Fresco Speaker - page 10

    10 Mounting the Fresco i On A Wall or Ceiling NOTE: F igures 19–24 illustrate the F resco i mounted in 4 different configurations. 3 Mark your wall with the center point for the wall bracket (see figure 19). 4 Using a level, square the wall bracket and hold it flush against the wall with the wall bracket's center hole over the point you just ...

  • Fresco Speaker - page 11

    Mounting the Fresco i On A Wall or Ceiling 11 5 Set the wall bracket aside. Using a 1 / 8 " bit, drill a pilot hole at all five points marked in the previous steps. If a pilot hole hits a stud during this step, DO NO T WIDEN that pilot hole or install a wall anchor at that location. If a pilot hole does not hit a stud, use a 1 / 4 " bit t ...

  • Fresco Speaker - page 12

    9 Place the F resco i onto the wall bracket and carefully slide the F resco i into place (see figure 23). 10 Using a 6mm Allen tool, attach a washer and cap nut onto each pin. Do not f ully tighten the cap nuts (see figure 23). 11 Make the signal connections from the amplifier (see ‘ Operation ’, pages 4). 12 Rotate the F resco i to point at th ...

  • Fresco Speaker - page 13

    H OME T HEA TER Home Theater 13 Figure 26. F resco i loudspeakers as front, center and surround (effects) channels. Abyss subwoofers as 0.1 (effects) channel. It had long been the practice of stereo buffs to connect their television to a stereo system. The advantage was the use of the larger speakers and more powerful amplifier of the stereo system ...

  • Fresco Speaker - page 14

    14 ATF (Advanced Thin Film) AT F ( A D V ANCED T HIN F ILM ) A TF Operation The MartinLogan A TF transducer (based on RADIA planar technology) consists of a micro-thin, low -mass Kaladex diaphragm with an ultra-light, etched conductive aluminum surface suspended between two high f ield strength neodymium super magnet arrays (see figure 27). When an ...

  • Fresco Speaker - page 15

    ATF (Advanced Thin Film) 15 How do I clean my speakers? Just use a dust free cloth or a soft brush to remove the dust from your speakers. W e recommend a specialty cloth (available at the Xtat ic shop at www .martinlogan. com) that cleans your speakers better than anything else we have tried. Do not spray any kind of cleaning agent on or in close p ...

  • Fresco Speaker - page 16

    16 Dimensional Drawings D IMENSIONAL D RA WINGS ...

  • Fresco Speaker - page 17

    System Frequency R esponse 75–20,000 Hz ± 3 dB Sensitivity 90 dB/2.83 volts/meter Impedance 5 ohms Crossover Frequency 500, 3200 Hz Components Air core coils, metal film and low dissipation electrolytic capacitors W oofer T ype T wo 4” (10.2cm) high rigidity aluminum cone with extended throw drive assembly , non-resonance asymmetrical chamber ...

  • Fresco Speaker - page 18

    18 Glossary of Audio Terms G LOSSARY OF A UDIO T ERMS AC. Abbreviation for alternating current. Active crossover . Uses active devices (transistors, ICs, tubes) and some form of power supply to operate. Amplitude. The extreme range of a signal. Usually measured from the average to the extreme. Arc. The visible sparks generated by an electrical disc ...

  • Fresco Speaker - page 19

    Glossary of Audio Terms 19 Inductance. The property of an electrical circuit by which a varying current in it produces a varying magnetic field that introduces voltages in the same circuit or in a nearby circuit. It is measured in henrys. Inductor . A device designed primarily to introduce inductance into an electrical circuit. Sometimes called a c ...

  • Fresco Speaker - page 20

    Lawrence, K ansas, USA tel 785.749.0133 fax 785.749.5320 www .martinlogan.com M A RTIN L OGA N the loudspeaker technology company ©2006 MartinLogan. All rights reserved. Rev . #111506 ® ...

Manufacturer Fresco Category Speaker

Documents that we receive from a manufacturer of a Fresco Speaker can be divided into several groups. They are, among others:
- Fresco technical drawings
- Speaker manuals
- Fresco product data sheets
- information booklets
- or energy labels Fresco Speaker
All of them are important, but the most important information from the point of view of use of the device are in the user manual Fresco Speaker.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Fresco Speaker, service manual, brief instructions and user manuals Fresco Speaker. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Fresco Speaker.

Similar manuals

A complete manual for the device Fresco Speaker, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Fresco Speaker by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Fresco Speaker.

A complete Fresco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Fresco Speaker - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Fresco Speaker, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Fresco Speaker, that we can find in the current document
3. Tips how to use the basic functions of the device Fresco Speaker - which should help us in our first steps of using Fresco Speaker
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Fresco Speaker
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Fresco Speaker in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Fresco Speaker?

Use the form below

If you did not solve your problem by using a manual Fresco Speaker, ask a question using the form below. If a user had a similar problem with Fresco Speaker it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)