English dropdown-ico

Manual Audiovox PRO-9671FT

22 pages 0.28 mb
Download

Go to site of 22

Summary
  • Audiovox PRO-9671FT - page 1

    Model PRO-9671FT Installation Manual 4 Channel Remote Car Starter With Full Feature Alarm System Installation Instructions This Unit Is Intended For Installation In V ehicles With 12 V olt Negative Ground Electrical Systems, Gasoline Engines, And Automatic T ransmissions Only . Kit Contents: PRO-9671FT Control Module (2) - Three Button Anti Code Gr ...

  • Audiovox PRO-9671FT - page 2

    The PRO-9671FT Remote Start/Alarm System is designed to be used with Automatic Transmission V ehicles Only! The unit provides no output for glow plug pre-heat and may not be desirable for diesel vehicles. If the diesel engine has a instant fire, (no glow plug pre-heat system), a tach signal input, and an Automatic Transmission, this unit may be use ...

  • Audiovox PRO-9671FT - page 3

    drill a 1/4" hole in the desired location and pass the connector end of the LED through the hole and toward the control module. Press the LED firmly into place until it is fully seated in the mounting hole. THE RANGE EXTENDER ANTENNA: The range extender antenna provided with this unit allows routing from below the dash board for maximum operat ...

  • Audiovox PRO-9671FT - page 4

    The PRO-9671FT is to be used in vehicles with AUT OMA TIC TRANSMISSIONS only! Although this combination Alarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be installed into a vehicle with a manual operated transmission. Doing so may result in serious personal injury and property damage. IMPORT ANT! DO NOT PLU ...

  • Audiovox PRO-9671FT - page 5

    BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "ST ART" or CRANK" positions, and will have 0 volts when the key is turned to the "OFF" and "ACCESSORY&quo ...

  • Audiovox PRO-9671FT - page 6

    WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red T race Wire: Parking Light Flasher Feed This wire is the common contact of the on board p arking light flasher relay . If the vehicle you are working on has +12 volt switched parking lights, connect this wire to a fused + 12 volt source. (Max. 15 Amps) NOTE: If the vehicle&ap ...

  • Audiovox PRO-9671FT - page 7

    Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches + 12 volts when the door is opened, (Most Fords and some Imports), you must connect this wire to the positive output from one of the vehicle's door pin switches. In most cases, the Purple wire will need to be connected to only one door switch no matter how m ...

  • Audiovox PRO-9671FT - page 8

    General Motors V A TS By-Pass Diagram Light Blue Wire: Ignition 3 Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of the applications described below , a relay will be ...

  • Audiovox PRO-9671FT - page 9

    Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. This wire should be connected to an external relay , and wired to the vehicles interior ...

  • Audiovox PRO-9671FT - page 10

    Orange Wire: Ground When Armed Output This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibit relay . Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85 (red wire) of the relay to an ignition wire in the vehicle that is +12 volts when the ignition switch ...

  • Audiovox PRO-9671FT - page 11

    Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. Chassis Ground Connection Detail Green w/ Orange T race Wire: T achometer Input Signal This wire will conti ...

  • Audiovox PRO-9671FT - page 12

    Dark Blue Wire: Delayed 300mA Pulsed Channel 2 Output The Dark Blue wire supplies a 300mA ground pulsed output whenever channel two of the receiver is accessed. Pressing the pre-programmed transmitter button for three seconds will access channel two. This is a low current output and must be connected to a relay to supply power to the trunk release ...

  • Audiovox PRO-9671FT - page 13

    2 Pin Control Switch: (Red Connector) The Black & Black w/White Trace wires loaded in the two pin red connector enable the operation of the Remote Start unit. When the Black w/ White Trace wire is grounded, the remote start unit is operable. When this wire is open from ground, the remote start is disabled. Route the twin lead Black & Black ...

  • Audiovox PRO-9671FT - page 14

    3 Wire Positive Switched Door Locks: In this application, the Red wire of the two pin harness provide sa+1 2 volt pulse during the disarming sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay . The Green wire of the two pin harne ...

  • Audiovox PRO-9671FT - page 15

    ALARM SELECT ABLE FEA TURES NOTE: The Alarm Selectable Features and Remote Start Selectable Features p rogramming steps following are based on transmitter button 1 being programmed for channel 1 and transmitter button 2 being programmed for channel 2. RF Programmable Features: Feature Selection 1 Chirp 2 Chirp Default First 1 Second Door Locks 3.5 ...

  • Audiovox PRO-9671FT - page 16

    REMOTE ST ART SELECT ABLE FEA TURES RF Programmable Features: LED Pattern 1 x Pause etc. 2 x Pause etc. 3 x Pause etc. 4 x Pause etc. 5 x Pause etc. 6 x Pause etc. 7 x Pause etc. 8 x Pause etc. Default Off 10 Minutes Steady T ach ---------------- Off during crank Off --------------- Park Lights Flashes 2 x RF start chirp confirm on 15 minute run ti ...

  • Audiovox PRO-9671FT - page 17

    Multi Coil Pack Adaptor: (Optional) The multi coil pack adaptor is designed for use with vehicles having multiple ignition coils where a single point tach signal is unavailable. T o use the adaptor , the Green/Black wires must connect to the negative side of the ignition coil(s). 1. For vehicles utilizing independent coils per cylinder , connect th ...

  • Audiovox PRO-9671FT - page 18

    TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. HOOD PIN SAFETY SHUT DOW ...

  • Audiovox PRO-9671FT - page 19

    CAUTION! REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARIL Y DISCONNECTED IN STEP 3 DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERA TION OF THE NEUTRAL SAFETY ST ART FEA TURE. MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the sa ...

  • Audiovox PRO-9671FT - page 20

    KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will prevent the vehicle with a Mechanical Neutral S tart Switch from starting in gear . AUDI ...

  • Audiovox PRO-9671FT - page 21

    METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. Cut ...

  • Audiovox PRO-9671FT - page 22

    OUTPUT GREEN/BLACK (-) TO CHANNEL 3 CONTROL RELA Y GREEN RED DOOR LOCKS (See page 13) RED BLUE L.E.D. (See page 13) BLUE RED GREEN BLACK SHOCK SENSOR (See page 13 & 14) BLACK BLACK w/WHITE CONTROL SWITCH (See page 13) WIRING DIAGRAM GRA Y BLACK w/GRA Y V ALET/PROGRAMMING SWITCH (See page 13) AUXILIARY OUTPUTS (See page 12) MUL TI-PIN I/O HARNES ...

Manufacturer Audiovox Category Remote Starter

Documents that we receive from a manufacturer of a Audiovox PRO-9671FT can be divided into several groups. They are, among others:
- Audiovox technical drawings
- PRO-9671FT manuals
- Audiovox product data sheets
- information booklets
- or energy labels Audiovox PRO-9671FT
All of them are important, but the most important information from the point of view of use of the device are in the user manual Audiovox PRO-9671FT.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Audiovox PRO-9671FT, service manual, brief instructions and user manuals Audiovox PRO-9671FT. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Audiovox PRO-9671FT.

Similar manuals

A complete manual for the device Audiovox PRO-9671FT, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Audiovox PRO-9671FT by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Audiovox PRO-9671FT.

A complete Audiovox manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Audiovox PRO-9671FT - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Audiovox PRO-9671FT, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Audiovox PRO-9671FT, that we can find in the current document
3. Tips how to use the basic functions of the device Audiovox PRO-9671FT - which should help us in our first steps of using Audiovox PRO-9671FT
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Audiovox PRO-9671FT
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Audiovox PRO-9671FT in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Audiovox PRO-9671FT?

Use the form below

If you did not solve your problem by using a manual Audiovox PRO-9671FT, ask a question using the form below. If a user had a similar problem with Audiovox PRO-9671FT it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)