English dropdown-ico

Manual Standard Horizon GM29

266 pages 5.16 mb
Download

Go to site of 266

Summary
  • Standard Horizon GM29 - page 1

    Product Photo/Illustration GM29 Integrator’s Manual ...

  • Standard Horizon GM29 - page 2

    The product described in this manual conf orms to the Radio and Telecommunication Terminal Equipment (R&TTE) directive 99/5/EC with requirements covering EMC directive 89/336/EEC and Low Voltage dire ctive 73/23/EEC. The product fulfils the requirements according to 3GPP TS 51.010-1, EN 301 489-7 and EN60950. SAR statem ent: This product is int ...

  • Standard Horizon GM29 - page 3

    3 LZT 123 7361 R1A Contents Part 1: Overv iew ............. ................... .................... ............. .................... ............ 11 1. Introduction ................................ ............................................................................ 13 1.1 Target Users .................................................... ...

  • Standard Horizon GM29 - page 4

    GM29 INTE GRATOR’S MANUAL 4 LZT 123 7 361 R1A 3.1 Switching On the Modem ............................................................................. 36 3.2 Switching Off the Modem ............................................................................ 36 3.3 Resetting the Modem .............................................................. ...

  • Standard Horizon GM29 - page 5

    5 LZT 123 7361 R1A 2.10 AT+CMOD Call Mode ........................................................................ 66 2.11 AT+CVHU Voice Hang-Up ................................................................ 67 2.12 AT+VTS DTMF and Tone Generation ........................................... 67 3. Control and Status ............................... ...

  • Standard Horizon GM29 - page 6

    GM29 INTE GRATOR’S MANUAL 6 LZT 123 7 361 R1A 5.2 AT+CRLP Radio Link Protocol ....................................................... 107 6. Data - GPRS .......................................................................................................... 109 6.1 AT+CGACT PDP Context Activate or Deactivate .............................. 109 6 ...

  • Standard Horizon GM29 - page 7

    7 LZT 123 7361 R1A 10.11 AT+ICF Cable Interface Char acter Format .................................. 141 10.12 AT+IFC DTE-DCE Local Flow Control ...................................... 142 10.13 AT+ILRR Cable Interface L ocal Rate Reporting ........................... 143 10.14 AT+IPR Cable Interface Port Command .................................... ...

  • Standard Horizon GM29 - page 8

    GM29 INTE GRATOR’S MANUAL 8 LZT 123 7 361 R1A 13.8 AT+CMSS Send From Storage ......................................................... 190 13.9 AT+CMGC Send Command .............................................................. 191 13.10 AT+CNMI New Message Indications to TE .................................... 194 13.11 AT+CMGR Read Message .... ...

  • Standard Horizon GM29 - page 9

    9 LZT 123 7361 R1A 16.17 AT+CUSD Unstructured Suppl ementary Service Data .................... 257 17. Alphabetical Listing of AT Commands ............................................................. 261 ...

  • Standard Horizon GM29 - page 10

    GM29 INTE GRATOR’S MANUAL 10 LZT 123 7 361 R1A ...

  • Standard Horizon GM29 - page 11

    Product Photo/Illustration Part 1: O verview ...

  • Standard Horizon GM29 - page 12

    ...

  • Standard Horizon GM29 - page 13

    13 LZT 123 7361 R1A 1. Introduction 1.1 Target Users GM29 modems are designed to be integrated into mach ine-machine or man-to-machine communications applications. They are intended to be used by manufacturers, system integrat ors, applications develope rs and developers of wireless communications equipment. 1.2 Prerequ isites It is assumed that th ...

  • Standard Horizon GM29 - page 14

    GM29 INTE GRATOR’S MANUAL 14 LZT 123 7 361 R1A 2. GM29 Modem 2.1 Desc riptio n The dual band EGSM 900/1800 MHz GM29 is a GSM/GPRS serial modem. The modem is a powerful and fle xible device that ca n be used in a wide range of teleme try and telematic s applications that r ely on the remote exchange of data, voice, SMS or faxes via the GSM cellula ...

  • Standard Horizon GM29 - page 15

    2. GM29 MODEM 15 LZT 123 7361 R1A 2.3 GM29 in a Co mmunicatio n System Figure 2.1 illustrates the main bloc ks of a wireless communication system using the GM29. It also shows th e communication principles of the system. The definitions in the fi gure, as used elsew here in this manual, are in accor dance with the recommendations of GSM 07.07. • ...

  • Standard Horizon GM29 - page 16

    GM29 INTE GRATOR’S MANUAL 16 LZT 123 7 361 R1A Figure 2.2 illustrates the interface between the modem and the application. The entire System Connector Interfac e is described in detail in “Electrical Description”, page 28 . Figur e 2.2 The Interface between the modem and the Application Note ! ITU-T standards define TE and TA as DTE (Data Ter ...

  • Standard Horizon GM29 - page 17

    2. GM29 MODEM 17 LZT 123 7361 R1A 2.4 Mai n Feat ures an d Servi ces The modem performs a set of telecom se rvices (TS) acc ording to GSM standard phase 2+, ETSI and ITU-T. The services and functions of the modem are implemented by issuing AT commands over the RS232 serial i nterfa ce. 2.4. 1 Typ es o f Mob ile Stat ion The GM29 is a dual band seri ...

  • Standard Horizon GM29 - page 18

    GM29 INTE GRATOR’S MANUAL 18 LZT 123 7 361 R1A 2.4.3 Voice Calls The GM29 offers the capability of mobile originated and mobile terminated voice calls, as well as supporting emergency ca lls. Multi-party, call waiting and call deflection features are ava ilable. Some of these features are network-operator specific. For the inter-connection of aud ...

  • Standard Horizon GM29 - page 19

    2. GM29 MODEM 19 LZT 123 7361 R1A • Network regist ration • Call barring • Call t ransfer 2.4. 7 Seria l Commu nic ation The GM29 enables an end-to-end c ommunication path to be established between the e xternal telemetry/te lematics a pplication and a remote terminal or host, via the GSM network. Once a path has be en set up, voice or data c ...

  • Standard Horizon GM29 - page 20

    GM29 INTE GRATOR’S MANUAL 20 LZT 123 7 361 R1A 2.5 Servic e and Support To contact customer support please use the details below: Customer Support Sony Ericsson Mobile Communications Maplewood Building Chineham Busine ss Park Basingstoke RG24 8YB E-mail: modules.support@sonyericsson.com or modules.info@sonyericsson.com Information about Sony Eric ...

  • Standard Horizon GM29 - page 21

    3. ABBREVIATIONS 21 LZT 123 7361 R1A 3. Abbreviations Abbreviation Expla nations CBM Cell Broadcast Message CBS Cell Broadcast Service CSD Circuit Switched Data DCE Data Circuit Terminating E quipment DTE Data Terminal Equipment DTMF Du al Tone Multi Frequency EFR Enhanced Full Rat e EMC Electro-Magnetic Compatibility ETSI European Telecommunicatio ...

  • Standard Horizon GM29 - page 22

    GM29 INTE GRATOR’S MANUAL 22 LZT 123 7 361 R1A ...

  • Standard Horizon GM29 - page 23

    Product Photo/Illustration Part 2: Integr ating the Modem ...

  • Standard Horizon GM29 - page 24

    ...

  • Standard Horizon GM29 - page 25

    25 LZT 123 7361 R1A 1. Mechanical Description 1.1 Over view The pictures below show the mechanical design of the GM29 along with the positions of the different connectors and mounting holes. The GM29 case is made of durable PC/ABS plastic. Figur e 1.1 GM29 viewed fr om the left side Figur e 1.2 GM29 vie wed fr om the right side Antenna connector R ...

  • Standard Horizon GM29 - page 26

    GM29 INTE GRATOR’S MANUAL 26 LZT 123 7 361 R1A Plea se note t he followi ng: • Mounting holes posit ioned at two of the corners make it possible to securely bolt the modem into your application. • Keypad, display , microphone, speaker and battery are not par t of the modem. • The SIM card is mounted in the modem. • The pins and electrical ...

  • Standard Horizon GM29 - page 27

    1. MECHAN ICAL DESCRIPT ION 27 LZT 123 7361 R1A 1.2 Physi cal Dime nsions Measurement s are given in millimetres . See also “Technica l Data”, page 44. 71.5 66.4 77.4 26.2 11.0 55.3 45.3 10.6 11.0 9.0 51.0 (x2) 3.5 ...

  • Standard Horizon GM29 - page 28

    GM29 INTE GRATOR’S MANUAL 28 LZT 123 7 361 R1A 2. Electrical Description All electrical c onnections to the GM29 are protec ted in compliance with the standard air (4 kV) and contact (8 kV) dischar ge ESD tests, of EN 301 489-1. The modem uses the following industry standard connectors: • RJ1 1 6- way (power connector) • RJ9 4-way (handset co ...

  • Standard Horizon GM29 - page 29

    2. ELECTRICAL DESC RIPTION 29 LZT 123 7361 R1A The power connec tor electrical characteristics are listed below: 2.2 Au dio Connecto r A 4-way RJ9 connector, as shown belo w, allows a telephone handset to be plugged into the modem, giving access to the microphone and earpiece signals. The connector ma y also be used to drive other analogue audio su ...

  • Standard Horizon GM29 - page 30

    GM29 INTE GRATOR’S MANUAL 30 LZT 123 7 361 R1A Audio signal descriptions are listed below: MICP and MICN are balanced di fferential microphone input signals. These inputs are compatible with an electret micr ophone. BEARP and BEARN are the speaker output signals. These are differential -mode outputs. The elect rical charact eristics are given in ...

  • Standard Horizon GM29 - page 31

    2. ELECTRICAL DESC RIPTION 31 LZT 123 7361 R1A 2.3 Antenna Co nnector The antenna connector allows transmission of radio fre quency (RF) signals between the modem and an ex ternal customer-supplied antenna. The modem is fi tted with a 50 Ω, FME male coaxial jack a s shown below . The table below shows the antenna elec trical characteri stics: Par ...

  • Standard Horizon GM29 - page 32

    GM29 INTE GRATOR’S MANUAL 32 LZT 123 7 361 R1A 2.4 SIM Car d Reader The GM29 is f itted with a SIM card reader desi gned for 3 V and 5 V SI M cards. It is the flip-up type which is lockable in the horizontal position and is accessed through a re movable panel as shown below. The SIM card reader i ncludes a SIM presence switch. This ensures t hat ...

  • Standard Horizon GM29 - page 33

    2. ELECTRICAL DESC RIPTION 33 LZT 123 7361 R1A 2.5 RS232 Ser ial Port The modem supports a standard RS232 seria l interface (EIA/TIA 574) via its 9 pin Sub-D connector, shown below. In line with serial communication terminology the GM29 serial modem should be consi dered as the dat a circuit-terminating equipment (DCE) and the external application ...

  • Standard Horizon GM29 - page 34

    GM29 INTE GRATOR’S MANUAL 34 LZT 123 7 361 R1A 2.5.1 Seria l Data The modem supports the standard data character format of 1 start bit, 8 bit data, no parity plus 1 stop bit, in t otal 10 bits per character . 2.5.2 Seria l Data Sig nals - RD, TD The default baud rate is 9.6 kbps, however higher bit rates up to 460 kbps are supported. At start-up ...

  • Standard Horizon GM29 - page 35

    2. ELECTRICAL DESC RIPTION 35 LZT 123 7361 R1A Data Terminal Ready (DTR) DTR indicates that the DTE is ready to transmit and rece ive data. It also acts as a hardware ‘ha ng-up’, terminating calls when switched high. The signal is active low. You can define the exact behaviour of DTR with an AT command. The DTR line can also be used to switch o ...

  • Standard Horizon GM29 - page 36

    GM29 INTE GRATOR’S MANUAL 36 LZT 123 7 361 R1A 3. Operation 3.1 Switch ing On the Modem There are two ways to switch on the modem, once power is applied. • either assert T O_IN high for > 0.2 s; • or activate the RS232 control line DTR, high for > 0.2 s. The modem is fully operational afte r 4 seconds. Logging onto a network may take lo ...

  • Standard Horizon GM29 - page 37

    3. OPERATI ON 37 LZT 123 7361 R1A 3.4 Oper ating Stat es/LED The modem has a green LED, as depicted below , which is used to indicate various operating states. These states a re described in following table. Note s! Switch off (Power Down) : DC power is applied but the modem is switched OFF. Standby: The GM29 is switched ON a nd camped on to the ne ...

  • Standard Horizon GM29 - page 38

    GM29 INTE GRATOR’S MANUAL 38 LZT 123 7 361 R1A 4. Hints fo r Integrating the Modem This chapter gives you advice and helpful hints on how to integrate the GM29 into your application from a hardware pe rspective. Please read and consider the information under the following headings before starting your integration work: • Safety advice and preca ...

  • Standard Horizon GM29 - page 39

    4. H INTS FOR INTE GRATING THE MOD EM 39 LZT 123 7361 R1A • When the SIM card hatch is opened, the SIM card connectors lie exposed under the SIM card holder . CAUTION: Do not touch these connectors! If you do, you may release an e lectrical dischar ge that could damage the modem or the SIM card. • When designing your application, the SIM card? ...

  • Standard Horizon GM29 - page 40

    GM29 INTE GRATOR’S MANUAL 40 LZT 123 7 361 R1A Signa l Str engt h The modem has to be placed in a way that ensures sufficient signal strength. To improve signal strengt h, the antenna can be moved to another position. Signal strength may depend on how close the modem is to a radio base station. You must ensure that the location at which you inten ...

  • Standard Horizon GM29 - page 41

    4. H INTS FOR INTE GRATING THE MOD EM 41 LZT 123 7361 R1A Securi ng the modem • Before securing the modem take into account the amount of additional space required for the ma ting connectors and cables that will be used in the application. • Where access is restricted, it may be easier to connect all the cables to the modem pr ior to secur ing ...

  • Standard Horizon GM29 - page 42

    GM29 INTE GRATOR’S MANUAL 42 LZT 123 7 361 R1A determine whether the antenna needs to be gr ounded or not. Your local antenna manufacturer might be able to design a special antenna suitable for your the application. 4.3.2 Ante nna Type Make sure that you choose the right type of antenna for the modem. Consider the following requireme nts: • the ...

  • Standard Horizon GM29 - page 43

    4. H INTS FOR INTE GRATING THE MOD EM 43 LZT 123 7361 R1A • Noise can be caused by electronic devices and ra dio transmitters. • Path-loss occurs as the strength of the received signal steadily decreases in proportion to the distance from the transmitter . • Shadowing is a form of environmental attenuation of radio signals caused by hills, bu ...

  • Standard Horizon GM29 - page 44

    GM29 INTE GRATOR’S MANUAL 44 LZT 123 7 361 R1A 5. Technical Data Data Features Shor t Mess age Se rvic e Featu res Voice Fea tures Fax Feat ures Data Storage CSD Up to 9.6 kbps HSCSD (2+ 1) Up to 19.2 kbps GPRS Class B (4+1) - P channe ls - Coding schemes CS 1 - CS4 85.6 kbps (subjec t to network support and terminal location) GSM 07.10 multiplex ...

  • Standard Horizon GM29 - page 45

    5. TECHNICAL DATA 45 LZT 123 7361 R1A Power Supply Power Consumption Power Do wn Mode Standby Mode (typical) Talk Mode (typical) Note s! Power Down Mode: DC power is applied but the modem is switched OFF. Standby Mode: The GM29 is switched ON and camped on to the network. No call in progress. Talk Mode: The GM29 is switched ON and a voice/data call ...

  • Standard Horizon GM29 - page 46

    GM29 INTE GRATOR’S MANUAL 46 LZT 123 7 361 R1A Radio Specif icati ons Audio S p ecif ications SIM Ca rd Read er Elect rical Connect ors and LE D Freque ncy rang e GM29 : EGSM 90 0 MHz and 18 00 MHz (dual ban d) Maximum RF outpu t power 2 W (900 MHz) and 1 W (1800 MHz) Ante nna impeda nce 50 Ω Static sensitivity Better t han –1 02 dBm Param et ...

  • Standard Horizon GM29 - page 47

    5. TECHNICAL DATA 47 LZT 123 7361 R1A Mech anical Spec ification Envir onmen tal spec ificatio ns Length 77 .4 mm Width 66.4 mm Hei ght 26 .2 mm Weight <1 3 0g Oper atin g temp eratu re range –25 °C t o +55 °C Storage tem peratu re range –40 °C t o +85 °C Relati ve humidi ty 5 - 9 5 %, non- cond ens ing Stationary vibrat ion, sinusoidal ...

  • Standard Horizon GM29 - page 48

    GM29 INTE GRATOR’S MANUAL 48 LZT 123 7 361 R1A Cert ifica t ion Dire ctive 19 99/ 5/EC EMC : EN 301 489-1 EMC : EN 301 489-7 Safety: EN 60 950 GSM 3GPP T S 51.010- 1 Tested according to GCF-CC ...

  • Standard Horizon GM29 - page 49

    6. DECLAR ATION OF CONFORMITY 49 LZT 123 7361 R1A 6. De claration of Con formity ...

  • Standard Horizon GM29 - page 50

    GM29 INTE GRATOR’S MANUAL 50 LZT 123 7 361 R1A ...

  • Standard Horizon GM29 - page 51

    Product Photo/Illustration Part 3: Usi ng AT Commands ...

  • Standard Horizon GM29 - page 52

    ...

  • Standard Horizon GM29 - page 53

    53 LZT 123 7361 R1A 1. Introduction to AT Com mands 1.1 Over view AT commands, issued from a computer in your application are used to control and implement the functions of the modem. Using AT commands, the following actions are possible: • Control of DCE •G P R S • Call control • Supplementary Service • SIM application tool kit The GM29 ...

  • Standard Horizon GM29 - page 54

    GM29 INTE GRATOR’S MANUAL 54 LZT 123 7 361 R1A [ ] Square brac kets are used to i ndicate that a certai n item is optional. For example, sub-parameters of a command or an optional part of a response. The brackets do not appear in the command line. Value The default values of the supported para meters are indicated by using bold text when presenti ...

  • Standard Horizon GM29 - page 55

    1. INTRODUCTION TO AT COMMANDS 55 LZT 123 7361 R1A • AT*<command>=[<parameter>] Exampl e! AT+ CFUN=0< CR> (powers down the modem) If several values are include d in the command, they are separated by commas. It is also possible to enter commands with no values. Additional commands may follow an extended syntax command on the sam ...

  • Standard Horizon GM29 - page 56

    GM29 INTE GRATOR’S MANUAL 56 LZT 123 7 361 R1A Possible for mats for the re sult codes are: • Basic format re sult code, such as OK. The Basic resul t code also has a numerical equivalent. • Extended format result code, prefixed with a plus sign (+) or an asterisk (*): – AT+<command>: <parameter > – AT*<command>: <par ...

  • Standard Horizon GM29 - page 57

    1. INTRODUCTION TO AT COMMANDS 57 LZT 123 7361 R1A 1.3 Error Codes 1.3. 1 +CM E ERRO R (Mo bile Equi pment Error Co de) This final result code is similar to the regular ERROR re sult code. If +CME ERROR: <err> is the result code for any of the commands in a command line, none of the commands in the same command line will be executed (neither ...

  • Standard Horizon GM29 - page 58

    GM29 INTE GRATOR’S MANUAL 58 LZT 123 7 361 R1A 1.3.2 +CMS ERROR (Message Serv ice Failure Result Code) This final result code indicates an er ror related to mobile equipment or to the network. The operation is si milar to the ERROR result c ode. None of the following comma nds in the s ame command line will be executed. Neither ERRO R nor OK resu ...

  • Standard Horizon GM29 - page 59

    1. INTRODUCTION TO AT COMMANDS 59 LZT 123 7361 R1A 1.4 Exampl es on Ho w to Use th e AT Comman ds After every group of AT commands there is a section where some of the more complicated commands are exemplified. For a deta iled description of the command in ques tion (valid parameter values, AT command syntax and Response syntax) you are re commende ...

  • Standard Horizon GM29 - page 60

    GM29 INTE GRATOR’S MANUAL 60 LZT 123 7 361 R1A ...

  • Standard Horizon GM29 - page 61

    61 LZT 123 7361 R1A 2. Call Control 2.1 AT+CPI N PIN Control See 3.23, AT+CPIN PIN Control 2.2 ATA Answer I ncoming Ca ll Answer and in itiate conn ection to an incomi ng call. Description Command Possible Responses Ans wer an inco ming call ATA •C O N N E C T •C O N N E C T < t e x t > •N O C A R R I E R •E R R O R •O K <text> ...

  • Standard Horizon GM29 - page 62

    GM29 INTE GRATOR’S MANUAL 62 LZT 123 7 361 R1A 2.3 ATD Dial Used to initiate a phone connection, which may be data or voice (phone number terminated by semicolon). Th e phone number used to establish the connection will consist of digits and modifiers, or a stored number specification. If the dial string is followed by a semicolon this informs th ...

  • Standard Horizon GM29 - page 63

    2. CALL CONTROL 63 LZT 123 7361 R1A transmitted during the first 125 milliseconds after transmission of the termination character are ignored. This is to allow the DTE to append additional control characters such as line feed afte r the command line termi nation charac ter. <dial_string> Description “0 1 2 3 4 5 6 7 8 9 * # +” Valid chara ...

  • Standard Horizon GM29 - page 64

    GM29 INTE GRATOR’S MANUAL 64 LZT 123 7 361 R1A 2.4 ATH Hang up Signals the MS to termina te an active call. 2.5 ATO Return to Online Dat a Mode Switch to the on-line data mode from the on-line command mode during an active call. Returns ERROR when not in on-line command mode. 2.6 ATP Select Pulse Di alling Command is ignored, and is implemented f ...

  • Standard Horizon GM29 - page 65

    2. CALL CONTROL 65 LZT 123 7361 R1A 2.8 ATX Call Progress Monitoring Contr ol Defines if the dial-tone detection and busy-tone detection are to be used during a call set-up. Note! If there is no net w ork avai lable the <n> para meter will dec ide if “NO DIALTONE ” or “NO CA RRIER” wil l be re turned. If t he call re cipient is busy, ...

  • Standard Horizon GM29 - page 66

    GM29 INTE GRATOR’S MANUAL 66 LZT 123 7 361 R1A 2.10 AT+ CMOD Call Mo de Selects the call mode of further dialing commands (D) or for ne xt answering command (A). Mode ca n be either single or alternating. In this ETS, terms “alternating mode” and “alternating call” r efer to all GSM bearer and teleser vices that incorporate more than one ...

  • Standard Horizon GM29 - page 67

    2. CALL CONTROL 67 LZT 123 7361 R1A 2.11 AT+CVHU Voice Hang-Up Selects whether ATH or “dr op DTR” causes a voice connection to be disconnected or not. Voice connect i on also includes alternating mode calls that are currently in voice mode. Note! When <mode>=2, this command mus t be viewed in conjunction with the V.25ter command &D, o ...

  • Standard Horizon GM29 - page 68

    GM29 INTE GRATOR’S MANUAL 68 LZT 123 7 361 R1A Note ! The AT+VTS command is used only during a voice call. <DTM F> Descr iption ASCII charac ter string An ASCII characte r string with entrie s in the set 0-9, #, *, A- D separated by commas. Each entry is interp reted as a single ASCII charact er. Example: The string “8,9” sends two DTM ...

  • Standard Horizon GM29 - page 69

    69 LZT 123 7361 R1A 3. Control and Status 3.1 ATQ Res ult Code Supp ressi on Determines whethe r or not t he DCE transmits r esult codes to the DTE. When result codes are being suppre ssed, no portion of any intermediate, final, or unsolicited result code - he ader, re sult text, line te rminator, or trailer - is transmitted. 3.2 AT S0 Au toma tic ...

  • Standard Horizon GM29 - page 70

    GM29 INTE GRATOR’S MANUAL 70 LZT 123 7 361 R1A 3.3 ATS2 Es cape Sequence Char acter Defines the character to be used as the esc ape sequence characte r when switching from on-line data mode to on-line command mode. The response to the command is modified to reflect the change. Note ! If the <esc> parameter is set to a value in the range of ...

  • Standard Horizon GM29 - page 71

    3. CONTR OL AND STAT US 71 LZT 123 7361 R1A the command line is terminated with a <CR> char acter (IA5 0/13), but the result code issued uses the char acter with the ordinal value 30 (IA5 2/14) in place of the <CR>. 3.5 A TS4 Response Forma tting Ch aracte r This S-parame ter re presents t he de ci mal IA5 value of the characte r genera ...

  • Standard Horizon GM29 - page 72

    GM29 INTE GRATOR’S MANUAL 72 LZT 123 7 361 R1A 3.6 ATS5 Co mmand Line Editi ng Character (BAC KSPACE) This S-paramete r repres ents the dec imal IA5 value of the characte r recognised by the DCE as a request to delete from the command line the immediate ly preceding char acter. 3.7 ATS6 Bl ind Dial Del ay Control Included for compatibility . N o ...

  • Standard Horizon GM29 - page 73

    3. CONTR OL AND STAT US 73 LZT 123 7361 R1A 3.8 ATS7 Connection Completion Timeout Defines the maxim um time allowe d between completion of dialling and the connection being established. If this time is exceeded then the connection is aborted. 3.9 ATS8 Comma Dial Modi fier Delay Control Included for co mpatibility. No functiona lity Description Com ...

  • Standard Horizon GM29 - page 74

    GM29 INTE GRATOR’S MANUAL 74 LZT 123 7 361 R1A 3.10 ATS1 0 Auto matic Di sconnect Delay Control Included for compatibility . N o functionalit y 3.11 AT* ECAM Ericss o n Call Monitoring This command activates or deactivates the call monitoring function in the ME. When this log function is activate d in the ME, the ME infor ms about call events, su ...

  • Standard Horizon GM29 - page 75

    3. CONTR OL AND STAT US 75 LZT 123 7361 R1A • to make it possible for the TE to di splay call state infor mation for an ongoing call. Examples AT*E CA M? *ECAM: 0 AT*ECAM=1 OK 3.12 AT*EDST Ericss on Da ylight Saving Time This command sets the daylight saving time hours. Note! This c ommand affe cts the MS clock s et with the A T+CCL K command . T ...

  • Standard Horizon GM29 - page 76

    GM29 INTE GRATOR’S MANUAL 76 LZT 123 7 361 R1A 3.13 AT*E MAR Ericsson Master Rese t This command requests the MS to reset user data. The user data in the MS will be reset to the default values. This command also unlocks the MS. 3.14 AT*EPE E Ericsson Pi n Event The command requests the MS to report when the PIN code has been inserted and ac cepte ...

  • Standard Horizon GM29 - page 77

    3. CONTR OL AND STAT US 77 LZT 123 7361 R1A 3.15 TAT+CCLK Set Cl ock and Date Sets the real t ime clock of the ME. I f setting fa ils in an ME, er ror +CME ERROR: <err> is returned. R ead command retur ns the curre nt setting of the clock. 3.16 AT+CE ER Extended Error Report Causes the TA to return one or more lines of information text <re ...

  • Standard Horizon GM29 - page 78

    GM29 INTE GRATOR’S MANUAL 78 LZT 123 7 361 R1A 3.17 AT+ CFUN Set Phone Funct ionality Select s the level of funct ionality <fun> in the MS. "Full functionality" results in the highest level of power usage. It is possible to activate all parts of the modem. Default ON state. "Minimum functionality" results in minimum powe ...

  • Standard Horizon GM29 - page 79

    3. CONTR OL AND STAT US 79 LZT 123 7361 R1A 3.18 AT+CIND Indicator Control Used to set the values of ME indicators. <ind> value 0 means that the indicator is off (or in state which can be identified as “off” state), 1 means that i ndicator is on (or in a state which i s more substant ial than “off” state), 2 is more substantial than 1 ...

  • Standard Horizon GM29 - page 80

    GM29 INTE GRATOR’S MANUAL 80 LZT 123 7 361 R1A 3.19 AT+CLAC List all avai lable AT Commands Causes the ME to return one or more lines of AT commands. This command has the same functionality as AT*. Note ! This command only returns the AT commands that ar e available to the user. 3.20 AT+CMEE Mobile Equi pment Error Disables or enables the use of ...

  • Standard Horizon GM29 - page 81

    3. CONTR OL AND STAT US 81 LZT 123 7361 R1A 3.21 AT+CMER Mobile Eq uipment Event Rep ortin g Enables or disables the sending of unsolicite d result codes from ME to TE in the case of key pressings, display changes, and indicator state changes. <mode> controls the proc essing of unsolicited result codes specified within this command. <bfr&g ...

  • Standard Horizon GM29 - page 82

    GM29 INTE GRATOR’S MANUAL 82 LZT 123 7 361 R1A 3.22 AT+ CPAS Phone Act ivity Status Returns the activity status <pas> of the ME. I t can be use d to interrogate the ME before requesting action fr om the phone. When the command is executed without the <mode> a rgument, the command returns <pas>-values from 0 to 128 (for supported ...

  • Standard Horizon GM29 - page 83

    3. CONTR OL AND STAT US 83 LZT 123 7361 R1A 3.23 AT+CPIN PIN Contr ol Sends the password to the ME, which is necessary to make the ME operational (SIM PIN, SIM PUK or PH-SIM). If the PI N is to be entered twice, the TA autonomously repeats the PIN. If no PIN r equest is pending, no action is taken towards the ME and an error message (+CME ERROR < ...

  • Standard Horizon GM29 - page 84

    GM29 INTE GRATOR’S MANUAL 84 LZT 123 7 361 R1A PH-SI M PIN ME is waiting PHone-to-SIM card password to be given SIM PIN 2 ME is waiting SIM PIN2 to be given. This <code> is recomm ended to be returned only w hen the last exec uted comma nd r esult ed i n PI N2 aut hen ticati on failure (i. e. +CME ERROR: 1 7 ); if PIN2 is not e ntered corre ...

  • Standard Horizon GM29 - page 85

    3. CONTR OL AND STAT US 85 LZT 123 7361 R1A 3.24 AT+CPWD Change Passwor d Sets a new pa ssword for th e facility lock function defined by com m and Facility Loc k +CLCK. Test command returns a list of pairs which prese nt the available facilities a nd the maximum length of thei r password. Description Command Possible Responses Request facility loc ...

  • Standard Horizon GM29 - page 86

    GM29 INTE GRATOR’S MANUAL 86 LZT 123 7 361 R1A <pwd len gth> Descr iption Integer type Maximum length of the password for the facility <err > Description 0 Phone failure 3 Operation not allowed 5 PH-SIM PIN required 10 SIM not inserte d 11 SIM PIN req uired 12 SIM PUK required 13 SIM failure 14 SIM busy 15 SIM wrong 16 Incorrect passw ...

  • Standard Horizon GM29 - page 87

    3. CONTR OL AND STAT US 87 LZT 123 7361 R1A 3.25 AT+CR Service Repor ting Contr ol Enables or disables displ a y of intermediat e bearer capa bility reports during the handshake phase. Intermedia te Result Codes: +CR: <serv> 3.26 AT+CRC Cellu lar Resul t Code Command controls whether or not; • the extended format of incoming call indication ...

  • Standard Horizon GM29 - page 88

    GM29 INTE GRATOR’S MANUAL 88 LZT 123 7 361 R1A Test command returns values supported by the TA as a compound value. Unsolicited Result Codes: +CRING: <type> 3.27 AT+ CSAS Save Setting s Saves active message service settings t o a non-volatile memory. A TA can contain several setti ngs profiles. Settings specified in commands Service Centre ...

  • Standard Horizon GM29 - page 89

    3. CONTR OL AND STAT US 89 LZT 123 7361 R1A 3.28 AT+CSQ Signal Strength Returns the re ceived signal stre ngt h indication <rssi> and channel bit error rate <ber> from the ME. Test c ommand returns values supported by the TA as compound values. Description Command Possible Responses Exec ute Sign al Stre ngth AT+CS Q • +CSQ: <rssi ...

  • Standard Horizon GM29 - page 90

    GM29 INTE GRATOR’S MANUAL 90 LZT 123 7 361 R1A 3.29 AT+CTZU Automati c Time Zone Update Enables and disables the automa tic time zone update via NITZ. If setting fails in an ME error, +CME ERR OR <err> is re turned. Description Command Possible Responses Enable and disable automati c time zone update via NITZ AT+CT ZU=<onoff> •+ C M ...

  • Standard Horizon GM29 - page 91

    91 LZT 123 7361 R1A 4. Audio AT*E2EAMS and AT*E2APR are new commands that repla ce the funtionality offere d by the *EALR, *EAMS, *EARS and *ELAM commands. Use the new commands in new applications. The old commands are included f or compat ibility. 4.1 AT*E 2EAMS Ericss on M2M Audio Prof ile Modificat ion This command allows the modification and co ...

  • Standard Horizon GM29 - page 92

    GM29 INTE GRATOR’S MANUAL 92 LZT 123 7 361 R1A • configure the whole profile, spec ifying each audio parameter in a comma se parated list ; • set a single parameter , gi ven by its parameter number ; • save the current profile to non-volatile memory under the c urrent profile number (see A T*E2APR). The current audio settings can also be di ...

  • Standard Horizon GM29 - page 93

    4. AUDI O 93 LZT 123 7361 R1A <op> Descript ion 0 Configure current profile (<pr1> to < pr21>) 1 Set <TxPGA> 2 Set <RxPGA> 3 Set <S ideT oneGa in> 4 Set <A uxIn Gain> 5 Set <MicInGain> 6 Set <TxAGC> 7 Set <V olume > 8 Set <Ma xVo lume> 9 Set <Mi cPat h> 10 Set <S pkPa th> ...

  • Standard Horizon GM29 - page 94

    GM29 INTE GRATOR’S MANUAL 94 LZT 123 7 361 R1A 4 5d B P G A g a i n 5 7.5 dB PGA g ain 6 –7.5 dB PGA gain 7 –10 dB PGA g ain <SideToneG ain> Description 0 10 dB 1 13 dB 2 16 dB 3 19 dB 4 22 dB 5 25 dB <Au xInp utGai n> Description 0 MUTE 1 13 dB 2 34 dB 3 46 dB <MicIn putGain> Description 0 MUTE 1 13 dB 2 25 dB 3 34 dB 4 46 ...

  • Standard Horizon GM29 - page 95

    4. AUDI O 95 LZT 123 7361 R1A <Volum e>, <MaxV olume> Description 0 MUTE 1-9 Volume levels 1-9 <Mic Path> , <SpkP ath> Description 0 OFF 1 MUTE 2 Internal (using micr op hone/ speaker) 3 External (usin g ATMS/AFMS) <TxPCM>, <RxPCM> Description 0 13 bit P CM 1 16 bit P CM <HFAlgorithm> Description 0 No ha nd ...

  • Standard Horizon GM29 - page 96

    GM29 INTE GRATOR’S MANUAL 96 LZT 123 7 361 R1A Examples AT*E2EAMS=? *E2EAMS=(0-21,255) OK Current default profile is 0: AT*E2EAMS? *E2EAMS: 2,2,3,2,3,2,5,9,3,3,0,1,0,0,0,1,1,1,1,1,1 OK Sets current prof ile with these set tings: AT*E2EAMS=0,2,1,2,0,0,2,5,9,2,2,0,1,0,0,0,1,1,0,0,1,1 OK Sets TxPGA gain to 0dB: AT*E2EAMS=1,2 OK Turns analog ringing ...

  • Standard Horizon GM29 - page 97

    4. AUDI O 97 LZT 123 7361 R1A 4.2 AT *E2APR M2M Audio Profil e Manipula tion This command allows the maniuplation and storage of the audio “profiles” stored in the MS. The requireme nt for the 2nd and 3rd parameters depend on the operation being carrie d out. Using the command you can: • Set one of the three audio profile s 0, 1 or 2 as the c ...

  • Standard Horizon GM29 - page 98

    GM29 INTE GRATOR’S MANUAL 98 LZT 123 7 361 R1A Examples AT*E2APR=? *E2APR= (0-4),(0-2),( 0-2) OK Current default profile is profile 0: AT*E2APR? *E2APR: 0 OK Set audio profile now used to profile 1: AT*E2APR=0,1 OK Audio profile 1 settings: AT*E2APR=1,1 *E2APR: 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 OK Copy audio profile 1 to audio profile 2: AT*E ...

  • Standard Horizon GM29 - page 99

    4. AUDI O 99 LZT 123 7361 R1A 4.3 AT*E ALR Erics son Audio Li ne Request Included for compa tibility. No functiona lity. Description Command Possible Responses Reque st the audio line s (ATMS,AFMS ) AT*EA LR=<m ode> [,<activation> [,<a ud_s tatus >]] •* E A L R : < m o d e > , <activation>,<resp> •O K •E R ...

  • Standard Horizon GM29 - page 100

    GM29 INTE GRATOR’S MANUAL 100 LZT 123 7 361 R1A 4.4 AT*EAMS Ericsson Audio Mode Selection Included for compatibility . N o functionalit y. Description Command Possible Responses Sets th e audio mode for th e application AT*EAMS =<inter nal_voic e_al g>[,<noise_reduction> [,<side tone > [,<sho rt_echo _cancel ing> [,<ATM ...

  • Standard Horizon GM29 - page 101

    4. AUDI O 101 LZT 123 7361 R1A 4.5 AT*E ARS Ericsson Audi o Ring Signal Included for compa tibility. No functiona lity. <short_echo_cancelin g> Description 0 Off 1 On <ATMS _gain> Description 0 Norm al (0 dB) (in terna l voi ce proc essin g) <Class> Description 0 None 1 Low end, class refer ence Hect or 2 Mid End, class r eference ...

  • Standard Horizon GM29 - page 102

    GM29 INTE GRATOR’S MANUAL 102 LZT 123 7 361 R1A 4.6 AT*E LAM Ericsson Local Audi o Mode Included for compatibility . N o functionalit y. 4.7 AT*EMIC Ericsson Microphone M ode Included for compatibility . N o functionalit y. Description Command Possible Responses Set local audio mode AT*ELAM =<mic> [,<loudspeak er>] • *ELAM : <mic ...

  • Standard Horizon GM29 - page 103

    4. AUDI O 103 LZT 123 7361 R1A 4.8 A T*EMIR Ericsso n Music M ute In dicati on Req uest Included for compa tibility. No functiona lity. 4.9 A T*EXVC Eric sson SET External Volum e Control Used to set or query whether a n external accessory such as the vehicle handsfree controls the audio volume. By default, the <external volume> is turned off ...

  • Standard Horizon GM29 - page 104

    GM29 INTE GRATOR’S MANUAL 104 LZT 123 7 361 R1A The set command is effective only as long as the phone senses that it is connected to an external acc essory that has issued the command. Once the phone and the accessory a re disconnected the <external volume> setting return s to default. <ext erna l v olum e> Descript ion 0 The phone M ...

  • Standard Horizon GM29 - page 105

    105 LZT 123 7361 R1A 5. Data - CSD/HSCSD Note! Since the modem does not support V42bis compression the following commands have not been implemented: •A T + D S •A T + D R 5.1 AT+CBST Select Bearer Service Type Selects the bearer servi ce <name> wi th data rate <speed>, and the connection element <ce> to be used whe n data call ...

  • Standard Horizon GM29 - page 106

    GM29 INTE GRATOR’S MANUAL 106 LZT 123 7 361 R1A 71 9600 bps V.1 10 (IS DN) 75 14400 bps V.11 0 (ISD N) 79 19200 bps V.11 0 (ISD N) 80 28800 bps V.11 0 (ISD N) 81 38400 bps V.11 0 (ISD N) 82 48000 bps V.11 0 (ISD N) 83 56000 bps V.11 0 (ISD N) <na me> Descr iption 0 Asyn chronou s connectio n (UD I or 3.1 kHz mod em) <ce> Descr iption ...

  • Standard Horizon GM29 - page 107

    5. DATA - CS D/HSCSD 107 LZT 123 7361 R1A 5.2 AT+CR LP Radi o Link Proto col Radio link protocol (RLP) parameters used when non-transpa rent data calls are originated may be alte red with this command. Available command subparameters depend on the RLP versions implemented by the device (e.g. <ver> may not be a vailable if device supports only ...

  • Standard Horizon GM29 - page 108

    GM29 INTE GRATOR’S MANUAL 108 LZT 123 7 361 R1A <T1> De scription 48 38 - 10 0 Acknowle dgment time r T1 (*10 ms) <N2 > Description 6 0 - 255 Re-transmission attempts N2 <T4> De scription 5 3 - 255 Re-se quenci ng period T4 (*1 0 ms) <ver> De scription Integer RLP version. Whe n version indication is not present, <ver&g ...

  • Standard Horizon GM29 - page 109

    109 LZT 123 7361 R1A 6. Data - GPRS 6.1 A T+C GACT PDP C onte xt Ac tivate or D eacti vate Used to activate or deac tivate the specifie d PDP context( s). After the command has completed, the MS remains in V.250 command state. If the MS is alre ady in the re quested state, the command is ignored and OK is returne d. If the reque sted state cannot b ...

  • Standard Horizon GM29 - page 110

    GM29 INTE GRATOR’S MANUAL 110 LZT 123 7 361 R1A 6.2 AT+CGATT GPRS Attach or Detach Used to attach the MS to, or detach the MS from, the GPRS/packet domain service. After the co mmand has completed, the MS remains in V.250 command state. If the MS is already in the requested state, the command is ignored and the OK response is returned. If the req ...

  • Standard Horizon GM29 - page 111

    6. DATA - GPRS 111 LZT 123 7361 R1A 6.3 AT +CGDATA Enter D ata Stat e Causes the MS to perform whatever ac tions are necessary to establish communication between the TE and the network using one or more GPRS/packet domain PDP types. This may include performing a GPRS/packet domain attach and one or more PDP c ontext activa tions. Description Comman ...

  • Standard Horizon GM29 - page 112

    GM29 INTE GRATOR’S MANUAL 112 LZT 123 7 361 R1A 6.4 AT+CGDCONT Define PDP Context Specifies PDP context parameter values for a PDP context identified by the (loca l) context ide ntificati on paramet er, <cid>. Description Command Possible Responses Sele ct PD P cont ext param eters +CGD CONT=[<ci d> [,<PDP_ type> [,<A PN> ...

  • Standard Horizon GM29 - page 113

    6. DATA - GPRS 113 LZT 123 7361 R1A <APN > Description Strin g type (Access Point Name) a string parameter which is a logical name t hat is u sed to select the GGS N or th e external packet data network . If the value is nu ll or omitted, then the subscription value will be requested <PDP_addr ess> Description Strin g type A string p ar ...

  • Standard Horizon GM29 - page 114

    GM29 INTE GRATOR’S MANUAL 114 LZT 123 7 361 R1A 6.5 AT+CGER EP GPRS Event Repor ting Enables or disables the sending of unsolicited result codes, +CGEV: XXX from MS to TE in the case of certain ev ents occurring in the GPRS/packet domain MS or the network. Description Command Possible Responses Set c ommand +CGEREP =[<mode> [,<bfr >]] ...

  • Standard Horizon GM29 - page 115

    6. DATA - GPRS 115 LZT 123 7361 R1A 6.6 AT+CG PADDR Show PDP Add ress Returns a l ist of PDP addres ses for the spec ified context identifiers. The test command returns a list of defined <cid>s. Description Command Possible Responses Show PDP addresses for sp ecified CIDs +CGP ADDR=[ <cid> [,<cid> [, …]]] •+ C G P A D D R : &l ...

  • Standard Horizon GM29 - page 116

    GM29 INTE GRATOR’S MANUAL 116 LZT 123 7 361 R1A 6.7 AT +CGQM IN Qu ality o f Service Profile (Minimum Acce ptable) Allows the TE to specify a mi nimum acceptable prof ile which is checked by the MS against the negotiated profile returned in the Activate PDP Context Accept message. The set comm and specifies a profile for the context identif ied b ...

  • Standard Horizon GM29 - page 117

    6. DATA - GPRS 117 LZT 123 7361 R1A <prece dence> Description 0 Subs crib ed ( from ne two rk) v alue us ed 1 High priority 2 Norm al priorit y 3 Low priorit y <delay > Description 0 Subscribed (from network) value used 1-4 Delay class <reliability> Description 0 Subscribed (from network) value used 1-5 Reliability class <peak ...

  • Standard Horizon GM29 - page 118

    GM29 INTE GRATOR’S MANUAL 118 LZT 123 7 361 R1A 6.8 AT+CGQR E Q Qua lity of Service Prof ile (Reques ted) Allows the TE to specify a qua lity of service prof ile that is used when the MS sends an activate PDP context request message to the network. 8 10 000 (~ 22 bits/s) 9 20 000 (~ 44 bits/s) 10 50 000 (~ 111 bits/ s) 11 100 000 (~0.2 2 kbi ts/s ...

  • Standard Horizon GM29 - page 119

    6. DATA - GPRS 119 LZT 123 7361 R1A The set command spe cifies a profi le for the context ident ified by the (loca l) cont ext ident ificatio n par amete r, <cid>. Since this is the same parameter that is used in the +CGDCONT command, the +CGQREQ command is effectivel y an extension to the +CGDCONT command. The QoS profile consists of a numbe ...

  • Standard Horizon GM29 - page 120

    GM29 INTE GRATOR’S MANUAL 120 LZT 123 7 361 R1A <mea n> Description 0 Subscribed (from net work) value u sed 1 Best effort 2 100 (~0 .22 b its/s) 3 200 (~0 .44 b its/s) 4 500 (~1 .11 b its/s) 5 10 0 0 ( ~ 2 . 2b i t s / s ) 6 20 0 0 ( ~ 4 . 4b i t s / s ) 7 5 000 (~1 1.1 bits/s) 8 10 000 (~ 22 bits/s) 9 20 000 (~ 44 bits/s) 10 50 000 (~ 111 ...

  • Standard Horizon GM29 - page 121

    6. DATA - GPRS 121 LZT 123 7361 R1A 6.9 AT+CG REG GPRS Ne twork Regist ration Status Controls the presentation of an unsol icited r esult code + CGREG: <stat> when <n>=1 and there is a change in the GPR S/packet domain network registration status of the MS, or code +CGREG: <stat>[,<lac>,<c i>] when <n>=2 and ther ...

  • Standard Horizon GM29 - page 122

    GM29 INTE GRATOR’S MANUAL 122 LZT 123 7 361 R1A 6.10 AT+ CGSMS Select Serv ice for MO SMS Messages Used to spec ify the ser vice or service preference that the MS will use to send MO SMS messages. The read command returns the cur rently selected ser vice or servi ce preferenc e. <ci> De scription String type Two byte cell ID in hexadecimal ...

  • Standard Horizon GM29 - page 123

    123 LZT 123 7361 R1A 7. Data - HSCSD 7.1 A T+CHSC HSCSD Current Call Pa rameters Returns information about the current HSCSD call parameter s, i.e. the current number of r eceive and transmit timeslot s, air interface user rat e and channel coding. Description Comm and Possible Responses Show cu rrent HSCS D call paramete rs AT+CHSC • +CHSC:<r ...

  • Standard Horizon GM29 - page 124

    GM29 INTE GRATOR’S MANUAL 124 LZT 123 7 361 R1A 7.2 AT+C HSD HSCSD Devi ce Para meters Shows information about HSCSD features supported by the ME/TA. Description Command Possible Responses Show HSCSD featu res supported by the ME/ TA AT+CHSD •+ C H S D : <mclass>,<maxRx>, <maxTx>, <sum>,<codi ngs> • +CME ERR OR: ...

  • Standard Horizon GM29 - page 125

    7. DATA - HSCSD 125 LZT 123 7361 R1A 7.3 AT+CH SN HSCSD Non Transparent Ca ll Configurat ion Controls parameters for non-transparent HSCSD ca lls. Changing <topRx> or <codings> during a call does not affect the curr ent call. Changing <wAiur> or <wRx> affects the current call only if <topRx> was non-zero when the call ...

  • Standard Horizon GM29 - page 126

    GM29 INTE GRATOR’S MANUAL 126 LZT 123 7 361 R1A 7.4 AT+CHSR HSCSD Parameter s Report With this comm and enabled, the i ntermediate result code + CHSR: <rx>,<tx>,<aiur>,<c oding> is returned (from TA to TE) when an HSCSD call is being set up. The result code represents the current (negotiated or renegotiated) H SCSD paramet ...

  • Standard Horizon GM29 - page 127

    7. DATA - HSCSD 127 LZT 123 7361 R1A but before possible TE-TA rate ( +ILRR) reporting and before the intermedi ate result code CONNECT i s transmitted. The f ormat of the intermedi ate result code is : +CHSR: <rx>,<tx>,<aiur>,< coding> For the val ue definitions , refer to “AT+C HSC HSCSD C urrent Call Parameters”, page ...

  • Standard Horizon GM29 - page 128

    GM29 INTE GRATOR’S MANUAL 128 LZT 123 7 361 R1A ...

  • Standard Horizon GM29 - page 129

    129 LZT 123 7361 R1A 8. Fax 8.1 AT*E 2FAX Ericsson M2M Fax Comm. Baud Ra te Modificat ion This command allows the modification of the factory default RS232 comm. setting between standard 9600 baud and 19200 baud. This is needed as the addition of fax capabilities, within the module, require communication between fax applications and the module to r ...

  • Standard Horizon GM29 - page 130

    GM29 INTE GRATOR’S MANUAL 130 LZT 123 7 361 R1A AT*E2FAX? *E2FAX: 0 (Current defa ult setting is 19200 baud) OK AT*E2FAX=0 OK (Sets default RS232 setting to 9600 baud) 8.2 Low Level Fa x Commands The following table of low level fax commands are supported and used by the GM29 for fax operation. AT+F AA AT+ FBADL IN AT+FBAD MUL AT+F BOR AT+FBUG AT ...

  • Standard Horizon GM29 - page 131

    131 LZT 123 7361 R1A 9. Identification 9.1 AT Attent ion Command This command is used to determine the presence of an MS. If the MS supports AT commands, it returns an OK final result code. 9.2 AT&F Set to Fact ory Defi ned Config uratio n This command instruc ts the DCE to set all para meters to defa ult values specified by the manufacturer, w ...

  • Standard Horizon GM29 - page 132

    GM29 INTE GRATOR’S MANUAL 132 LZT 123 7 361 R1A 9.4 AT* List al l Supported AT Commands Lists all the commands supported by the MS. 9.5 AT+CGMI Read MS Manufacturer Ide ntifica tion Causes the MS to return one or more lines of information text. 9.6 AT+CGMM Read MS Model Identific ation Causes the MS to return one or more lines of information text ...

  • Standard Horizon GM29 - page 133

    9. IDENTIFICATION 133 LZT 123 7361 R1A 9.7 AT+CG M R Read MS Revis ion Id entifica tion This command causes the MS to return a string containing information about the software version. 9.8 AT+CG SN Read MS Product Serial Number Identif i catio n This command causes the MS to return the IMEI ( International Mobile station Equipment Ide ntity), which ...

  • Standard Horizon GM29 - page 134

    GM29 INTE GRATOR’S MANUAL 134 LZT 123 7 361 R1A This command provides compatibility with Microsoft Windows 95. 9.10 AT+GCAP Request Modem Capa bilities Li st Returns a list of valid modem comm and prefixes. <val ue> Descr iption 0 Same informat ion as +GMM command (model identification) 1 Same information as +GMR command (revision identific ...

  • Standard Horizon GM29 - page 135

    135 LZT 123 7361 R1A 10. Interface 10.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 10.2 AT&C Circuit 109 (DCD) Contr ol Determines the behaviour of the carr ier detect. 10.3 AT&D Circui t 108 (DTR) Resp onse Controls all actions ini tiated by data terminal ready from DTE. Description Command Possible Responses Set behavior of carrier ...

  • Standard Horizon GM29 - page 136

    GM29 INTE GRATOR’S MANUAL 136 LZT 123 7 361 R1A 10.4 AT&S Ci rcuit 107 (DSR) Respons e Determines the behaviour of the data set rea dy signal. 10.5 AT+WS46 Mo de Selection Allows an accessory to que ry and control the cellular protocol mode of the phone. Description Command Possible Responses Set behaviou r of data set ready AT&S[ <val ...

  • Standard Horizon GM29 - page 137

    10. IN TERFA CE 137 LZT 123 7361 R1A 10.6 ATE Command Echo The setting of this parame ter determines whether or not the DCE echoes characters rece ived from the DTE during command state and online comm and s tate. 10.7 ATV DCE Re sponse F ormat Select either descriptive or numeric response c odes. The ATV command sets the verbose numeric response c ...

  • Standard Horizon GM29 - page 138

    GM29 INTE GRATOR’S MANUAL 138 LZT 123 7 361 R1A List of result codes 10.8 A TZ Reset t o Defau lt Configur ation This command inst ructs the DCE to set all para meters to their default values as specified by the user. Consider hardware configura tion switches or non-volatile pa rameter storage (if implemented) when using this command. ATV1/ ATV=1 ...

  • Standard Horizon GM29 - page 139

    10. IN TERFA CE 139 LZT 123 7361 R1A Commands included on the same command line as the Z command will be ignored. 10.9 AT+CMUX Switch to 07 .10 Multiplex Pro tocol SI C25-68003 The command is used to turn on the multiplexe r. Only “no transparency is supported”. The parameter <k> is not used. The default values for the pa rameters below a ...

  • Standard Horizon GM29 - page 140

    GM29 INTE GRATOR’S MANUAL 140 LZT 123 7 361 R1A <port_speed> Description 1 96 0 0b i t s / s 2 19 200 bits/s 3 38 400 bits/s 4 57 600 bits/s 5 115 200 bits/s 6 230 400 bits/s 7 460 800 bits/s <N1 > Description 31 Default maximu m frame size <T1> De scription 10 100ms default time r <N2 > Description 3 Default maximu m numb ...

  • Standard Horizon GM29 - page 141

    10. IN TERFA CE 141 LZT 123 7361 R1A 10.10 AT +CRES Restore SMS Settings Restores message service settings from non-volatile memory to active memory. A TA can contain sever al profiles of settings. S ettings specified in c ommands Servic e Cent re Address +CSCA, Set Message Parame ters +C SMP and Select Ce ll Broadcast Message Types +CSCB (if imple ...

  • Standard Horizon GM29 - page 142

    GM29 INTE GRATOR’S MANUAL 142 LZT 123 7 361 R1A 10.12 AT +IFC DTE-DCE Loca l Flow Cont rol Defines the flow control be tween the modem and the computer when in on-line data mode. No flow control is enabled in any of the command modes. <par ity> De scription 3 Space. Default value Description Command Possible Responses Defines DTE- DCE local ...

  • Standard Horizon GM29 - page 143

    10. IN TERFA CE 143 LZT 123 7361 R1A 10.13 AT +ILRR Cable Interf ace Local Rate Repor ting Specifies whether or not the extende d-format “+ILRR:<rate>” informati on text is transmitt ed from the DCE to the DTE. The <r ate> reported shal l represent the curre nt (negotiated or re negotiated) DTE- DCE rate. If en abled, the inte rmedi ...

  • Standard Horizon GM29 - page 144

    GM29 INTE GRATOR’S MANUAL 144 LZT 123 7 361 R1A The specified rate takes effect following the issuance of any result code(s) assoc iated with the cur rent command lin e. 10.15 AT *E2ESC M2M Escape Sequ ence Guard Time Defines a guard time for the es cape sequence in GPRS to return to on- line comma nd mode i.e. if ++ + AT<CR> is r eceived e ...

  • Standard Horizon GM29 - page 145

    145 LZT 123 7361 R1A 11. Netwo rk 11.1 AT*E2 CD Ericsson M2M Cel l Descri ption Controls the presentation of an unsolicited result code E2CD: when <n>=1, or whe n there is a change in one of the network cell parame ters, E2CD: <la c>,<ci>,<ta >. Read command returns the status of result code presen tation and seve ral values ...

  • Standard Horizon GM29 - page 146

    GM29 INTE GRATOR’S MANUAL 146 LZT 123 7 361 R1A <ta> De scription 0-63 A ccording t o GSM 04 .18 V8.6.0, t he coding of the t iming advanc e value is t he binary repres entation of t he timin g advance in bit periods; 1 bit period = 48/13 ìs. <ta> is the intege r represen tation o f the timin g advance in bin ary forma t 64-255 Reser ...

  • Standard Horizon GM29 - page 147

    11. N ETWORK 147 LZT 123 7361 R1A 11.2 AT*E2EMM Ericsson M2M Engineering Monitoring Mode Description Command Possible Responses Set the response presen tation mode AT*E2EMM= <n>[,< m>] •E R R O R •O K Display mode neighbour cells are ta ken from the toplist *E2EMM: Serving Cell MCC,MNC,LAC,Ce llID,BSIC,Ch[,RxL,C1, C2][,RxLFull,RxLSu ...

  • Standard Horizon GM29 - page 148

    GM29 INTE GRATOR’S MANUAL 148 LZT 123 7 361 R1A There are four presentation format modes ( Display, Compact, Verbose, and Reduced Display) and two res ponse types (one shot response or continuous unsolicited responses). The purpose of the presentation format mode Display is to display the data in a readable f orm, including headers and line break ...

  • Standard Horizon GM29 - page 149

    11. N ETWORK 149 LZT 123 7361 R1A <neighborcell1 mcc>,<neighborce ll1 mnc>,<neighborcell1 lac>, <neighborcell1 ci>,<ne ighborcell1 bsic>,<neighborcell1 ch>, <neighborcell1 rxl>[,<ne ighborcell1 C1>,<neighborcell1 C2>], <neighborcell2 mcc>,<neighborce ll2 mnc>,<neighborcell2 lac> ...

  • Standard Horizon GM29 - page 150

    GM29 INTE GRATOR’S MANUAL 150 LZT 123 7 361 R1A 4 Enable compact network location in formation unsolicited result code. The re will be continuous u nsolicited information responses <m> seconds apart 5 One s hot pre sent ation o f the netwo rk locat ion inform ation (verbo se format), including 1 6 BTSs, com ing from t he Serving Cell signal ...

  • Standard Horizon GM29 - page 151

    11. N ETWORK 151 LZT 123 7361 R1A <rxqsub> is the pa rameter t hat indicat es the quality in the received signal on dedicated mode. The measur ement ave rage is applie d to a subset of a SACCH mult iframe. <rxl> Description Integer type Received Signal Strength level in dBm measured on idle mode <rxlfull> Description Integer type ...

  • Standard Horizon GM29 - page 152

    GM29 INTE GRATOR’S MANUAL 152 LZT 123 7 361 R1A 4 1.9 % < BER < 2. 7 % 5 3.8 % < BER < 5. 4 % 6 7.6 % < BE R < 11 .0 % 7 BER > 15.0 % <c1 > Description Integer Path Loss criterion parameter for ne ighbour cells. The MS calculates this parame ter, in idle mode, to decide if t he cell is suitable to camp on. After the cal ...

  • Standard Horizon GM29 - page 153

    11. N ETWORK 153 LZT 123 7361 R1A 11.3 AT*E2S PN M2M Servic e Provide r Indic ation Causes the MS to return the service provider name stored in the SIM card (<spi> parameter). The text will consist of a maximum of 16 bytes containing the service provider na me stored in the EF SPN file in the SIM card (see GSM 11.11). ERROR is returned if th ...

  • Standard Horizon GM29 - page 154

    GM29 INTE GRATOR’S MANUAL 154 LZT 123 7 361 R1A 11.5 AT*E CSP Ericsson C ustomer Serv ice Profile This command is used to read the customer se rvice profi le (CSP) from the SIM. CSP is a list on the SIM, which indicat es the services th at are user accessible. Eac h of the services has a relate d bit within the CSP . The services are grouped into ...

  • Standard Horizon GM29 - page 155

    11. N ETWORK 155 LZT 123 7361 R1A 11.6 AT*EPNR Ericsson Rea d SIM Preferred Networ k This command is used to read the SIM preferr ed list of networks (EF PLMNSEL ). Description Command Possible Responses Read entries in SIM preferred list AT*EPNR =<format> [,<in dex 1> [,<in dex 2]] •* E P N R : <index1 >,<oper1>[ ...] ...

  • Standard Horizon GM29 - page 156

    GM29 INTE GRATOR’S MANUAL 156 LZT 123 7 361 R1A 11.7 AT*EPNW Ericsson Writ e SIM Preferred Network This command is used to edit the SIM preferred list of networks (EF PLMN SEL ). The entry field <oper> contains mobile country code (MCC) and mobile network code (MNC). 11.8 AT*E2 SSN Eric sson M2M SIM Serial Number This command requests the S ...

  • Standard Horizon GM29 - page 157

    11. N ETWORK 157 LZT 123 7361 R1A EXAMPLES AT*E2SSN? 8944110063503224707 OK where the raw data containe d in the ICCid field on the SIM is 984411003605234207F7. Test command: AT*E2SSN=? OK 11.9 AT*ESLN Ericsson Set Line Name Sets the name tag for a selected line. Description Command Possible Responses Set s the lin e name tag in the MS AT*ES LN=< ...

  • Standard Horizon GM29 - page 158

    GM29 INTE GRATOR’S MANUAL 158 LZT 123 7 361 R1A 11.1 0 AT+CIM I Subscrib er Identifi cation Causes the TA to return <IMSI>, identifying the individual SIM attache d to the ME. 11.11 AT +CLCK Facilit y Lock The command is used to lock, unlock or interrogate an ME or a network facility <fa c>. A password is normally needed to carry out ...

  • Standard Horizon GM29 - page 159

    11. N ETWORK 159 LZT 123 7361 R1A “AO” BAOC (bar all outgoing calls) “OI” BOIC (bar outgoing international calls) “AI” BAIC (bar all inc oming calls) “IR” BIC-Roam (bar in coming calls when roaming outs ide the home co untry) “OX” BOIC-exHC (bar outgoing int ernational calls except to home co untry) “AB” All barring services ...

  • Standard Horizon GM29 - page 160

    GM29 INTE GRATOR’S MANUAL 160 LZT 123 7 361 R1A 11.12 AT +CNUM Subsc riber Numbe r This command returns t he MSISDNs related to the subscriber (this information can be stored in the SIM or in the ME). If subscriber has different MSISDN for di fferent services, ea ch MSISDN is returned i n a separate line. 16 Data circ uit sync 32 Data circ uit as ...

  • Standard Horizon GM29 - page 161

    11. N ETWORK 161 LZT 123 7361 R1A 11.13 AT +COLP Connected Line Identifi cation Pres entation This command refers to the GSM/UM TS supplementary service COLP (Connected Line Identification Presentation) that e nables a calling subscriber to ge t the connecte d line identity (COL) of the called party after set ting up a mobile originate d call. The ...

  • Standard Horizon GM29 - page 162

    GM29 INTE GRATOR’S MANUAL 162 LZT 123 7 361 R1A Test command returns values supported by the TA as a compound value. Intermedia te Result codes: +COLP: <number>,<type>[,<subaddr>,<sa type> [,<alpha>]] <n> De scription 0 Disable 1 Enable <m> Descr iption 0 COLP not provisioned 1 COLP provisioned 2 unk nown ...

  • Standard Horizon GM29 - page 163

    11. N ETWORK 163 LZT 123 7361 R1A 11.14 AT +COPS Operat or Selecti on Forces an at tempt to select and register the G SM network operator. Description Command Possible Responses Request oper ator selection AT+COPS =[<mode> [,<f orma t> [,<o per> ]]] • +C ME ERRO R <err > •O K • ERRO R Shows the current setting AT+C OPS ...

  • Standard Horizon GM29 - page 164

    GM29 INTE GRATOR’S MANUAL 164 LZT 123 7 361 R1A 11.1 5 AT+CREG Network Reg istr ation Set command c ontrols the presenta ti on of an unsolicited result code +CREG: <stat> when <n>=1 and ther e is a change in the ME network registration status. Read command returns the status of result code presentation and an integer <sta t>, wh ...

  • Standard Horizon GM29 - page 165

    11. N ETWORK 165 LZT 123 7361 R1A 11.16 AT *ECPI Cipheri ng Indicator This command allows the external applic ation to activa te/deactivate the ciphering indication. The ciphering indication allows the external application to detect when the mobile connection becomes deciphered and thus unsecured. Test command gives the current value of the <swi ...

  • Standard Horizon GM29 - page 166

    GM29 INTE GRATOR’S MANUAL 166 LZT 123 7 361 R1A Unsolicited Result Codes *ECPV - Ciphering Indicator SYNTAX - Unsolicited Re sult code Description Response When Set com mand inform s the TE when a comm unicat ion is unsecu red du e to th e fact that the ne twork is not encipher ing the comm unica tion *ECPV: <cip hering> When AT*ECPI enable ...

  • Standard Horizon GM29 - page 167

    11. N ETWORK 167 LZT 123 7361 R1A 11.17 AT *E2NBTS Ericss on M2M Neighbour BTS The set command shall provide wi th the ARFCNs (<ch>) and the BSIC (the BSIC is a cell colour code) to the MS in order to monitor those channels, belonging to the ne ighbour cells, instead of the one s that come through the air interface, in the se rving cell infor ...

  • Standard Horizon GM29 - page 168

    GM29 INTE GRATOR’S MANUAL 168 LZT 123 7 361 R1A <mcc> De scription String Type Three digits in decimal format. The Mobile Country Code identifies the PLMN serving cell country accord ing to ITU <mn c> Description String Type Two digits in decimal format. The Mobile Network Code identifi es the PLMN operat or in the se rving cell <c ...

  • Standard Horizon GM29 - page 169

    169 LZT 123 7361 R1A 12. Phonebook 12.1 AT*E2 PBCS Ericsson M2M Phonebook Check Sum Command causes the ME to return the phone book checksum <cks> stored internally . Phone book checksum is recalculated whenever there is a change in the phone book. By reque sting the checksum, the external application can detect if the phone book in the ME has ...

  • Standard Horizon GM29 - page 170

    GM29 INTE GRATOR’S MANUAL 170 LZT 123 7 361 R1A 12.3 AT* E SCG Ericsson Cr eate G roup This command creates a new group in the hierarchical phone book. The group is stored at the first available position. There are 10 group positions in the hierarchical phone book. <gind ex> Description 1-10 The grou p index withi n the h ierar chical phon ...

  • Standard Horizon GM29 - page 171

    12. PHONEBOOK 171 LZT 123 7361 R1A 12.4 AT*ESCN Erics son Set Credit Card Number Command is used to: • set up a credit card number in the ME. • disable c redit card calls. • enable one of the credit card ca ll services. • query the settings for one of the services. • query the act ive credit call acce ss server . Description Command Possi ...

  • Standard Horizon GM29 - page 172

    GM29 INTE GRATOR’S MANUAL 172 LZT 123 7 361 R1A <ind exn> Description 1 Index number to th e firs t credi t card cal l access s erver 2 Index number to the secon d credi t card call access s erver <selindexn> Descri ption 0 Credit card calling disabled 1 Index number to th e firs t credi t card cal l access s erver 2 Index number to t ...

  • Standard Horizon GM29 - page 173

    12. PHONEBOOK 173 LZT 123 7361 R1A 12.5 AT*ESDG E rics son Delete Gr oup This command deletes the group at position <gindex> from the hierarchical phone book. 12.6 AT*ESDI Erics son Delete Gr oup Item The command deletes the item with <index> in the group with <gindex>. Description Command Possible Responses Deletes a group define ...

  • Standard Horizon GM29 - page 174

    GM29 INTE GRATOR’S MANUAL 174 LZT 123 7 361 R1A 12.7 AT*ESG R Eri csson Gro up R ead This command lists the groups in the hierarchical phone book. 12.8 AT *EGIR Ericsson Gr oup Item Read This command lists the items stored in the group identified by <gindex>. Description Command Possible Responses Lists the groups defined in th e hier archi ...

  • Standard Horizon GM29 - page 175

    12. PHONEBOOK 175 LZT 123 7361 R1A 12.9 AT*ESNU Ericsson Settin gs Number This command sets a <type> number, in the format <number type>, in the MS. <itemi ndex> Description Integer The item' s index within th e phonebook/ contacts/group Description Command Possible Responses Sets a number in the MS AT*ES NU=< type >, & ...

  • Standard Horizon GM29 - page 176

    GM29 INTE GRATOR’S MANUAL 176 LZT 123 7 361 R1A 12.10 AT +CPBF Phonebook Find Returns phone book entries whose alphanumeric field starts with <findtext >. Only currently sele cted source will be searched f or, 12.1 1 AT+CPBR Phonebook Read Returns phone book entries in location number range <index1>... <index2> from the current ...

  • Standard Horizon GM29 - page 177

    12. PHONEBOOK 177 LZT 123 7361 R1A <numb er> Description string type Phone number of format <typ e> <type> Desc ription 129 ISDN/ telephony num bering plan, nation al/intern ational unknow n 145 ISDN/ telephony num bering plan, inte rnational number 161 ISDN/ telephony num bering plan, nation al number 128 - 255 Other value s refe ...

  • Standard Horizon GM29 - page 178

    GM29 INTE GRATOR’S MANUAL 178 LZT 123 7 361 R1A 12.12 AT +CPBS Phone Stor age Selects phone book memory storage <sto rage>, which is used by other phone book commands. Read command returns curre ntly selected memory, and when supported by ma nufacturer, number of used locations and total number of locations in the memory. Description Comman ...

  • Standard Horizon GM29 - page 179

    12. PHONEBOOK 179 LZT 123 7361 R1A 12.13 AT +CPBW Phoneboo k Write Writes phone book entry in location number <index> in the c urrent phone book memory storage area , selected with AT+CPBS. If the <number> and <text> pa rameters ar e omitted, the entry is deleted. If <index> is omitted but <number> is inc luded, the en ...

  • Standard Horizon GM29 - page 180

    GM29 INTE GRATOR’S MANUAL 180 LZT 123 7 361 R1A <tlen gth> Description integer type Value indicating the maximum len gth of field <text> ...

  • Standard Horizon GM29 - page 181

    181 LZT 123 7361 R1A 13. Short Message Serv ic es - Point to Point 13.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 13.2 AT+CGSMS Select Service for MO SMS Messages See 6.10, AT+CGSMS Select Service for MO SMS Messages 13.3 AT+CPMS Preferred Mes sage Stora ge Common for both PDU (Proto col Data Unit) and Text Mode s Selects memory storage < ...

  • Standard Horizon GM29 - page 182

    GM29 INTE GRATOR’S MANUAL 182 LZT 123 7 361 R1A Test command returns lists of memory storage supported by the TA. <me m1> Descr iption string type Mem ory from which messages are read and deleted (commands List Messages +CMGL, Read Message +CMGR and Delete Message +CMGD) “ME” ME message storage “SM” SIM message storage. Defa ult val ...

  • Standard Horizon GM29 - page 183

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 183 LZT 123 7361 R1A 13.4 AT+CSCA Service Centr e Addres s Comm on fo r both PDU a nd Te xt Mo des Updates the SMSC address, through which mobile originated SMs are transmitted. I n text mode, the set ting is used by send (+CMGS) and write (+CMGW) commands. In PDU mode, the setting is used by the same co ...

  • Standard Horizon GM29 - page 184

    GM29 INTE GRATOR’S MANUAL 184 LZT 123 7 361 R1A 13.5 AT+CMGF Message F o rmat Common for both PDU and Text Modes This command tells the TA, which input and output format to use for messages. The <mode> parameter indica tes the format of messages used with send, list, read and wr ite commands, and unsolicited result codes resulting from rece ...

  • Standard Horizon GM29 - page 185

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 185 LZT 123 7361 R1A same as specified by the send message command, +CMGS. If writing fails, final result code +CMS ERROR: <err> is returned. See “AT+CPMS Preferred Message Storage”, page 181. Text Mode Stores m essage (e ither SMS- DELIVER or SMS-SU BMIT) to memory storage <mem2>. Memory ...

  • Standard Horizon GM29 - page 186

    GM29 INTE GRATOR’S MANUAL 186 LZT 123 7 361 R1A Note ! SMS-COMMANDs and SMS-STATUS-REPORTs cannot be stored in text mode. <sta t> Description 2 Stored unsent message (only applicable to SMs) <oa> De scription String type GS M 03.40 TP-Orig ina ting-Ad dress V alue i n strin g format ; BCD numbers (or GSM defa ult alphabet charac ters) ...

  • Standard Horizon GM29 - page 187

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 187 LZT 123 7361 R1A 13.7 AT+CMGS Send Message PDU Mode Sends a message from a TE to th e network (SMS-SUBMIT). Message reference value <mr> is returned to the TE on successful message delivery. Optionally, when AT+CSMS <service> value is 1 and there is network support, <ackpdu> is retu ...

  • Standard Horizon GM29 - page 188

    GM29 INTE GRATOR’S MANUAL 188 LZT 123 7 361 R1A Text Mode Sends a message from a TE to th e network (SMS-SUBMIT). Message referenc e value <m r> is returned to the TE on successful mes sage delivery. Optionally, when AT+CSMS <service> value is 1 and there is network support, <scts> is returned. Values can be used to identify mes ...

  • Standard Horizon GM29 - page 189

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 189 LZT 123 7361 R1A carriage returns can be used ( previously mentioned four characte r sequence shall be sent t o the TE after every carriage return ente red by the user); if TE character set is “HEX”: the entered text should consist of two IRA character long hexadecimal numbers whic h ME/TA conver ...

  • Standard Horizon GM29 - page 190

    GM29 INTE GRATOR’S MANUAL 190 LZT 123 7 361 R1A AT+CMGS=“+447747008670” > Test SMS  +CMGS: 15 OK 13.8 AT+CMSS Send From Storage PDU mode Sends message with location valu e <index> from message storage <mem2> to the network (SMS-SUBMIT or SMS-COMMAND). Referenc e value <mr> i s returned to the TE on successful message d ...

  • Standard Horizon GM29 - page 191

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 191 LZT 123 7361 R1A supports, <scts> is returned. If sending fails in a network or an ME error, final result code +CMS ERROR: <err> is returned. This command is abortable. 13.9 AT+CMGC Send Command PDU Mode Sends a command message from a TE to the network (SMS- COMMAND). The entering of PDU ...

  • Standard Horizon GM29 - page 192

    GM29 INTE GRATOR’S MANUAL 192 LZT 123 7 361 R1A TE on successful message deliv ery. Optionally (when +CSMS <service> value is 1 and network supports) <a ckpdu> is returned. Values can be used to identify message upon unsolicited delivery status report result code. If sending fails in a ne twork or an ME error, final result code +CMS E ...

  • Standard Horizon GM29 - page 193

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 193 LZT 123 7361 R1A 8-bit octets (refer to +CMGS). Message reference value <mr> is returned to the TE on successful message delivery. Optionally, when +CSMS <service> value is 1 and there is networ k support, <scts> is returned. Values can be used to identify messa ge upon unsolicited ...

  • Standard Horizon GM29 - page 194

    GM29 INTE GRATOR’S MANUAL 194 LZT 123 7 361 R1A 13.10 AT +CNMI New Mess age Indic ation s to TE PDU Mode Selects the procedure for the way in which ne w messages re ceived from the network, are indicated to the TE when it is active, e.g. DTR signal is ON. If the TE is i nactive (DTR si gnal is OFF), me ssage receiving is carried out as specified ...

  • Standard Horizon GM29 - page 195

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 195 LZT 123 7361 R1A Unsolicited Result c odes: +CMT : <le ngth><CR><LF ><pdu> +CMTI: <mem>,<index> +CBM: <length><CR><LF><pdu> +CDS: <length><CR><LF><pdu> +CDS I: <m em>< index > <mt> Desc ription 0 No ...

  • Standard Horizon GM29 - page 196

    GM29 INTE GRATOR’S MANUAL 196 LZT 123 7 361 R1A Text Mode Selects the procedure for the way in which ne w messages re ceived from the network, are indicated to the TE when it is active, e.g. DTR signal is ON. If TE is inactiv e (DTR signal is OFF), message re ceiving is carried out as specified in GSM 03.38 (3G TS 23.038). If the command fails an ...

  • Standard Horizon GM29 - page 197

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 197 LZT 123 7361 R1A Unsolicited Result c odes: +CMT:<oa>, [<alpha> , <scts> [,<tooa>,<fo>,<pid>,<dcs>,< sca>,<tosca>,<length>] <CR><LF> <data> (Text Mode e nabled). Refer to the show text mode command, +CSDH for infor mation o ...

  • Standard Horizon GM29 - page 198

    GM29 INTE GRATOR’S MANUAL 198 LZT 123 7 361 R1A 13.11 AT +CMGR Read Message PDU Mode Returns messa ge with locati on valu e <index> from prefer red message storage <mem1> to the TE. Status of the message and entire message data unit <pdu> is returned. If status of the message is ‘received unread’, status in the storage chang ...

  • Standard Horizon GM29 - page 199

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 199 LZT 123 7361 R1A Text Mode Returns message s with location i nde x <index> from message storage <mem1> to the TE. About text mode parameters in Italics, refer command Show Text Mode Parameters (+CSDH), If the status of the message is ‘received unread’, status in the storag e changes t ...

  • Standard Horizon GM29 - page 200

    GM29 INTE GRATOR’S MANUAL 200 LZT 123 7 361 R1A <oa> De scription String type GS M 03.40 TP-Orig ina ting-Ad dress V alue i n strin g format ; BCD numbers (or GSM defa ult alphabet charac ters) are conver ted to cha racters of th e curre ntly selec ted TE charact er (refer comman d +CSCS). Type of add ress given by <tooa> <da> D ...

  • Standard Horizon GM29 - page 201

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 201 LZT 123 7361 R1A <data> The entered text should be f ormatted as follows: if <dcs> (set with +CSMP ) indica tes that G SM 03.38 defa ult alphabet is used and <fo> indic ates that GS M 03.40 TP-User- Data-Head er-Indicat ion is not se t: if TE ch aracter se t other t han "HEX&qu ...

  • Standard Horizon GM29 - page 202

    GM29 INTE GRATOR’S MANUAL 202 LZT 123 7 361 R1A <ct> De scription Integer GSM 03.40 TP--c ommand-type. Defa ult value is 0 <sn> De scription Integer GSM 03.41 CBM seri al numb er <mid > Description String type All different possible combinations of CBM message identifiers (refer <mid>) (de fault is empty string); e.g . “ ...

  • Standard Horizon GM29 - page 203

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 203 LZT 123 7361 R1A 13.12 AT +CMGL Lis t Messag e PDU Mode Note! Returns messages with status valu e <stat> from preferre d message storage <mem1> to the TE. Entire data units <pdu> are returned. If status of th e message is ‘ received unrea d’, status in the storage changes to ‘ ...

  • Standard Horizon GM29 - page 204

    GM29 INTE GRATOR’S MANUAL 204 LZT 123 7 361 R1A <alph a> Description String type Manufacturing specific. Should be left e mpty but not omitted <len gth> Description Integer type Value indicating in PDU mode (+CMGF=0), th e length of the actual TP data uni t in octets (i. e. the RP laye r SMSC addr ess oc tets a re not coun ted i n the ...

  • Standard Horizon GM29 - page 205

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 205 LZT 123 7361 R1A Text Mode Returns messages with status valu e <sta t> from mes sage storage <mem1> to the TE. About text mode parameters in Italics, refer command Show Text Mode Parameters (+CSDH). If the status, of the message is ‘received unread’, status in the storag e changes to ...

  • Standard Horizon GM29 - page 206

    GM29 INTE GRATOR’S MANUAL 206 LZT 123 7 361 R1A <sta t> Description Integer Indicates the status of messages in memory 0 Received unread message (new message) 1 Received read message 2 Stored unsent message (only applicable to SMs) 3 Stored sent message (only applicable to SMs) 4 All messages (only applicable to + CMGL command) <oa> D ...

  • Standard Horizon GM29 - page 207

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 207 LZT 123 7361 R1A <scts > Description Strin g type GSM 03.40 TP-ser vice-centre -time-stamp in time-string format (r efer <d t>) <lengt h> Description Integer type Value indicating in PDU mode (+CMG F=0), the len gth of the ac tual TP d ata unit in oc tets (i.e. the RP layer SMSC add ...

  • Standard Horizon GM29 - page 208

    GM29 INTE GRATOR’S MANUAL 208 LZT 123 7 361 R1A Example AT+CMGF=1 OK AT+CMGL=? +CMGL: “REC UNREAD” ,“REC READ”,“S TO UNSENT”,“STO SENT”,“ALL” OK <dt> De scription String GSM 03.40 TP-Discharge-Time in string format "yy/MM/ dd,hh:mm:ss+-zz w here char acters in dicate year , month, day, hour,minu tes, seconds a nd ti ...

  • Standard Horizon GM29 - page 209

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 209 LZT 123 7361 R1A 13.13 AT +CMGD Delete Message Common for both PDU and Text modes Deletes messa ge from prefe rred me ssage storage <mem1> location <index>. If deleting fails, final re sult code +CMS ERROR: <err> is returned. Test command shows the valid memory locations. 13.14 AT + ...

  • Standard Horizon GM29 - page 210

    GM29 INTE GRATOR’S MANUAL 210 LZT 123 7 361 R1A 13.15 AT +CSMP Set Te xt Mode Parameters Only Ap plic able to Te xt Mode Used to select values for additional parameters needed when SM is sent to the network or placed in a storag e when text format message mode is selected. It is possible to set the validity period starting from when the SM is rec ...

  • Standard Horizon GM29 - page 211

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 211 LZT 123 7361 R1A 13.16 AT +CSCS Select Char acter Set This command informs the TA which character set <c hset> is used by the TE. The TA is then able to convert cha racter strings correctly between TE and ME characte r sets. When TA-TE inter face is set to 8-bit operation and the used TE alphab ...

  • Standard Horizon GM29 - page 212

    GM29 INTE GRATOR’S MANUAL 212 LZT 123 7 361 R1A 13.17 AT +CSMS Select Message Ser vice Common for both PDU and Text Modes Selects messaging service <service >. It returns the types of messages supported by the ME: <mt> for mobile terminated messages, <mo> for mobile originated messages and <bm> for broadcast type messages. ...

  • Standard Horizon GM29 - page 213

    13. SHORT MESSAGE SERVICES - POINT TO POIN T 213 LZT 123 7361 R1A <err> Descript ion 0...12 7 GSM 04 .11 Anne x E-2 va lues 128.. .255 GSM 03. 40 sub claus e 9.2. 3.22 val ues 300 ME failure 302 Operation not allowed 304 Invalid PDU m ode pa ramet er 310 SI M not inse rted 311 SI M PIN required 312 PH- SIM PIN requir ed 313 SIM failure 314 SI ...

  • Standard Horizon GM29 - page 214

    GM29 INTE GRATOR’S MANUAL 214 LZT 123 7 361 R1A ...

  • Standard Horizon GM29 - page 215

    215 LZT 123 7361 R1A 14. Short Message Services - Cell Broadcast 14.1 AT+CNMI New Message Indi cations to TE See 13.10, AT+CNMI New Message Indications to TE 14.2 AT+CSCB Select Cell Broadcas t Message Type Common for both PDU and text modes Selects which types of CBMs are to be rece ived by the ME. Description Command Possible Responses Select cel ...

  • Standard Horizon GM29 - page 216

    GM29 INTE GRATOR’S MANUAL 216 LZT 123 7 361 R1A ...

  • Standard Horizon GM29 - page 217

    217 LZT 123 7361 R1A 15. SIM Application Too lkit 15.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 15.2 AT*E2 STKS SIM Applica tion Toolk it Settings Allows the external application to disable or enable the presentation of the unsolicited result codes corresponding to the STK commands. Parameter <on_off> is used to disabl e or enable th ...

  • Standard Horizon GM29 - page 218

    GM29 INTE GRATOR’S MANUAL 218 LZT 123 7 361 R1A 15.3 AT*E2 STKD M2M STK Displ ay Text The ME passes the parameters w ithin DISPLAY TEXT com mand to the external application by means of the unsolicited result code *E2STKD. Command AT*E2STKD allows the external application to send the appropria te answer af ter receivi ng the unsolicited re sult co ...

  • Standard Horizon GM29 - page 219

    15. SIM APPLICATION TOOLKIT 219 LZT 123 7361 R1A Values follow GSM 11.14 standard. 15.4 AT* E2STKG M2M STK Get Inkey The ME passes the para meters within GET INKEY com mand to the external application by means of the unsolicited result code E2STKG. The external application then sends AT*E2STKG with the user response. <pri orit y> Description ...

  • Standard Horizon GM29 - page 220

    GM29 INTE GRATOR’S MANUAL 220 LZT 123 7 361 R1A Answer command al lows the external app lication to send the appropriate answer, a fter receivi ng the unsolicited result code, and before the timeout expires. If Answer command is sent once the timeout expires, an ERROR response is generated. If <answer> pa rameter is not 0, a failure has occ ...

  • Standard Horizon GM29 - page 221

    15. SIM APPLICATION TOOLKIT 221 LZT 123 7361 R1A Values follow GSM 11.14 standard. 15.5 AT* E2STKI M2M STK G et Input The ME passes the para meters within GET INP U T command to t he external application by means of the unsolicited result code E2STKI. The external application sends AT *E2STKI with the user response. AT*E2STKI allows the external ap ...

  • Standard Horizon GM29 - page 222

    GM29 INTE GRATOR’S MANUAL 222 LZT 123 7 361 R1A Test command returns the list of suported values, and <prompt_text_length>. Values follow GSM 11.14 standard. Note ! If <response_type>=3 (Yes/No), the length of <user_response> is 1 byte. Otherwise, the ME gives an ERROR message. Unsolicited Result Codes: *E2STKI: <min_length_r ...

  • Standard Horizon GM29 - page 223

    15. SIM APPLICATION TOOLKIT 223 LZT 123 7361 R1A Values follow GSM 11.14 standard. <min_length_response > Desc rip tion Integer type (0-160) Value indicating the min imum length of response field <user_re sponse> <max _len gth_ respon se> De scr ipti on Integer type (0-160) Value indicatin g the maximum length of response field &l ...

  • Standard Horizon GM29 - page 224

    GM29 INTE GRATOR’S MANUAL 224 LZT 123 7 361 R1A 15.6 AT*E2 STKL M2M STK Select Item The ME passes the parameters within SELECT ITEM command to the external application by means of the unsolicited resu lt code *E2STKL. Command AT*E2STKL allows the external application to send the appropria te answer af ter receivi ng the unsolicited re sult code, ...

  • Standard Horizon GM29 - page 225

    15. SIM APPLICATION TOOLKIT 225 LZT 123 7361 R1A Unsolicited Re sult Codes: E2STKL: <NbrOfItems>,<codi ng> ,<text_lengt h>,<alpha_id> [,<default>]< CR><LF>E2STKL: <item_id1>,<coding>, <text_length>,<ite m1><CR><LF>[…] E2STKL: <item_idn>, <coding>,<text_le ...

  • Standard Horizon GM29 - page 226

    GM29 INTE GRATOR’S MANUAL 226 LZT 123 7 361 R1A 15.7 AT*E2S TKM M2M STK Set Up Menu The ME passes the pa rameters wi thin SET UP MENU command to th e external application, so that the STK menu can be built externally, by means of the unsolicited result code *E2STKM. The current menu can be removed by se nding only the parameter <on_off> = 0 ...

  • Standard Horizon GM29 - page 227

    15. SIM APPLICATION TOOLKIT 227 LZT 123 7361 R1A Unsolicited Re sult Codes: *E2STKM: <NbrOfItems>,<coding>,<text_length>, <alpha_id><CR><LF>E2STKM : <item_id1>,<coding>, <text_length>,<item1>[<CR><L F>[…]E2STKM: <item_idn>, <coding>,<text_length>,<itemn&g ...

  • Standard Horizon GM29 - page 228

    GM29 INTE GRATOR’S MANUAL 228 LZT 123 7 361 R1A The parameters have no default values. 15.8 AT*E2 STKN M2M STK Envelope (Menu Selecti on) The application informs the ME about the selecte d menu item by means of the AT*E2SKTN command. The ME answers with OK, or ERROR. The Do command allows the external applic ation to select the menu item in the i ...

  • Standard Horizon GM29 - page 229

    15. SIM APPLICATION TOOLKIT 229 LZT 123 7361 R1A Values follow GSM 11.14 standard. Unsolicited Re sult Codes: *E2STKC: <ton>,<dial_string> ,<SetUpRequirement>,<coding>, <text_length>,<alpha_id> Values follow GSM 11.14 standard. <answer > Description 0 OK. Performed as requir ed. It corr esponds to ‘0 0’ ...

  • Standard Horizon GM29 - page 230

    GM29 INTE GRATOR’S MANUAL 230 LZT 123 7 361 R1A The maximum length is fixed 15.10 *E 2STKE STK Send Short Message Unsolicited Result Code: *E2STKE: <coding>, < text_length >, <alpha_id> The ME passes the <alpha_id> within SEND SHORT MESSAGE command to the external application, by means of the uns olicited result code *E2ST ...

  • Standard Horizon GM29 - page 231

    15. SIM APPLICATION TOOLKIT 231 LZT 123 7361 R1A 15.11 *E2 STKP STK Send SS Unsolicited Re sult Code: *E2STKP: <ton>, <SS_string>, <coding>, < text_length>, <alpha_id>, <SS_r eturn > The ME passes the parameter s wi thin SEND SS command to the external application, by mea ns of the unsolicited result code *E2STKP ...

  • Standard Horizon GM29 - page 232

    GM29 INTE GRATOR’S MANUAL 232 LZT 123 7 361 R1A 15.12 *E 2STKU STK Send USSD Unsolicited Result Code: *E2STKU: <coding>, <text_length>, <alpha_id> Description: The ME shall passes the <alpha_id> parameter within SEND USSD command to the external application, by means of the uns olicited result code *E2STKU. This informs th ...

  • Standard Horizon GM29 - page 233

    15. SIM APPLICATION TOOLKIT 233 LZT 123 7361 R1A 15.13 *E2 STKR STK Refre sh Unsolicited Re sult Code: *E2STKR: <indicator> The ME informs the external application about the coming REFRES H command, by means of the unsolicited result code *E2STKR (eg Reset is coming). 15.14 AT *E2STKTO SIM Ap plicat ion Toolk i t Setti ngs Paramete r Command ...

  • Standard Horizon GM29 - page 234

    GM29 INTE GRATOR’S MANUAL 234 LZT 123 7 361 R1A Unsolicited resu lt code: *E2STKTO: <command> 2 Set Up Call co mmand tim eout is se t to the val ue of <timer > 3 Display Te xt command timeout i s set to th e value of <timer > 4 Get Inpu t command time out is set to th e value of <timer > 5 Selec t Item c ommand timeou t is ...

  • Standard Horizon GM29 - page 235

    235 LZT 123 7361 R1A 16. Su pplementary Services 16.1 AT+CPIN PIN Control See 3.23, AT+CPIN PIN Control 16.2 AT+CAC M Accumulated Cal l Meter Resets the Advi ce of Charge rel ated accumulated call meter value in SIM file EF ACM . ACM contains the tot a l number of home units for both the current and prec eding calls. SIM PIN2 is usually required to ...

  • Standard Horizon GM29 - page 236

    GM29 INTE GRATOR’S MANUAL 236 LZT 123 7 361 R1A 16.3 AT+CAMM Ac cumulated Call Meter Maximum Sets the Advic e of Char ge relate d accumulated call meter maximum value in SIM file EF AC Mmax . ACMmax contains the maximum number of home units allowed to be consumed by the subscriber. When ACM (refer +CACM) reache s ACMmax calls are prohibited. SIM ...

  • Standard Horizon GM29 - page 237

    16. SUPPL EMENTARY SE RVICES 237 LZT 123 7361 R1A 16.4 AT+CAOC Advi ce of Charge Use of Advice of Charge supplementary service command enable s the subscriber to get information about the cost of calls. With <mode>=0, the execute c ommand retur ns the curre nt call meter va lue from the ME. The command also include s the possibility to ena bl ...

  • Standard Horizon GM29 - page 238

    GM29 INTE GRATOR’S MANUAL 238 LZT 123 7 361 R1A 16.5 AT+CPUC Pri ce Per Unit and C urrency Table Sets the parameters of Advice of Charge related price per unit and currency table in SIM file EF PUCT . PUCT information can be used to convert the home units (as used in +CAOC, +CACM and +CAMM) into currency units. SIM PIN1 or SIM PIN2 (depending on ...

  • Standard Horizon GM29 - page 239

    16. SUPPL EMENTARY SE RVICES 239 LZT 123 7361 R1A 16.6 AT*EDI F Eri csson Divert Func tion This command enables and disables notif ication of divert status changes with the unsolicited r esult code *EDIF. Unsolicited Re sult Codes: *EDIF: <reason>,<status>,< classx>[,<number>,<type>] Description Command Possible Respon ...

  • Standard Horizon GM29 - page 240

    GM29 INTE GRATOR’S MANUAL 240 LZT 123 7 361 R1A 16.7 AT*EIPS Identity Pr esen tation Se t This command enables or disables th e presentation of the alpha tag of the Caller ID and Called ID to the TE if the ID is re cognized. The alpha tag is the first name and the last name. The presentation is done by an unsolicited result code, *ELIP for Caller ...

  • Standard Horizon GM29 - page 241

    16. SUPPL EMENTARY SE RVICES 241 LZT 123 7361 R1A 16.8 AT*ELI N Ericss on Line Set This command reque sts the ME to set th e current li ne to <line> . Note! The f ollowing command r eads its valu e from the curr ent line and is thus affected by the use of *ELIN: AT+CACM - Acc umulated Cal l Meter 16.9 AT*E2SSD M2M Suppleme ntary Service Dispa ...

  • Standard Horizon GM29 - page 242

    GM29 INTE GRATOR’S MANUAL 242 LZT 123 7 361 R1A Refer to GSM 02.30 for Public MMI services and codes. 16.10 AT *E2SSI M2M Suppleme nt ary Service Indic ations This command allows the user to display the unsolicited response code *E2SSI on network responses (either command confirmation or error responses) for Supplementar y Services . This can be ...

  • Standard Horizon GM29 - page 243

    16. SUPPL EMENTARY SE RVICES 243 LZT 123 7361 R1A 4 SSI_ SIM_E RROR 5 SSI_ NUM BER_E RR 6 SSI_CA LL_BARRED 7 SSI_N OT_AVAI LABLE 8 SSI_UNSUCCESS FUL 9 SSI_NOT_ ALLOWED 10 SSI_NETWORK_ PROBLEM <Opc ode> Desc ription 10 REGIS TER_SS 11 ERASE_SS 12 ACTI VATE_S S 13 DEACTIVATE_SS 14 INTERROGATE_SS <SScode > Description 0 ALL_ SS 16 ALL_LINE ...

  • Standard Horizon GM29 - page 244

    GM29 INTE GRATOR’S MANUAL 244 LZT 123 7 361 R1A 81 MULTI_PARTY 112 ALL_ CHARGING _SS 113 ADVICE_OF _CHARGE_I NFORMATION 114 ADVICE_OF_CHARGE _CHARGING 144 ALL_BA RRING_SERVICES 145 BARRING_ OF_OUTGOING_CALLS 146 BARRING_O F_ALL _OUTGOI NG_CAL LS 147 BARRING_ OF_ALL_OUTGOING_INTERNATI ONAL_CALLS 148 BARRING_O F_ALL _OG_IN TERNATI ONAL_ NON_HPLM N_ ...

  • Standard Horizon GM29 - page 245

    16. SUPPL EMENTARY SE RVICES 245 LZT 123 7361 R1A 33 TS_SHO RT_MES SAGE_MT_P P BS_P AD_A CCES S_CA _300B PS 34 TS_SHO RT_MESSAG E_MO_PP BS_PAD_A CCESS_CA _1200BPS 35 BS_PAD _ACCE SS_CA_ 1200_7 5BPS 36 BS_P AD_AC CESS_ CA_2400B PS 37 BS_P AD_AC CESS_ CA_4800B PS 38 BS_P AD_AC CESS_ CA_960 0BPS 40 BS_A LL_DATA _PDS_S ERVICE S 44 BS_D ATA_PDS _2400 BP ...

  • Standard Horizon GM29 - page 246

    GM29 INTE GRATOR’S MANUAL 246 LZT 123 7 361 R1A 4 SS_STATUS_PROVISIONED 7 SS_STATUS_PRA <For wardedTo Nr> Description String Phone number string in d ouble quote s <NoReplyConditionTime> Description 0-65 532 Integer v alue for ti me <CLI_Re striction Option > Description 0 PERM ANEN T 1 TEMPORARY_DEFAULT_RESTRICTED 2 TEMPORARY_D ...

  • Standard Horizon GM29 - page 247

    16. SUPPL EMENTARY SE RVICES 247 LZT 123 7361 R1A 16.11 AT +CCFC Call Forwa rdi ng number and Conditions This command allows control of the call forwarding supplementary service. Registration, erasure, a ctiva tion , deactivation, and status query are supported. When querying the status of a network se rvice (<mode>=2) the re sponse line for ...

  • Standard Horizon GM29 - page 248

    GM29 INTE GRATOR’S MANUAL 248 LZT 123 7 361 R1A <type> De scription integer format Type of address octet 129 ISDN /telephony nu mbering plan, national/internation al unkn own. Default va lue if ‘+’ is not in <sca> 145 ISDN/telephon y numbering plan, international number. Default value if ‘+’ is in <sca> 161 ISDN /telepho ...

  • Standard Horizon GM29 - page 249

    16. SUPPL EMENTARY SE RVICES 249 LZT 123 7361 R1A 16.12 AT +CCWA Call Waiting This command allows control of the c all waiting supplementary service according to 3GPP TS 22.083. Activation, deactivation and status query are supported. When querying the status of a network se rvice (<mode>=2) the re sponse line for ‘not active’ case (<s ...

  • Standard Horizon GM29 - page 250

    GM29 INTE GRATOR’S MANUAL 250 LZT 123 7 361 R1A Unsolicited Result Codes: +CCWA: <number>, <type>, <class> <classx> Description integer Sum of int egers ea ch re present ing a cla ss of inform ation. Default value is 7 1 Voice L1 2 Data 4 Fax 8 Short message service 16 Data circ uit sync 32 Data circ uit async 64 Dedi cate ...

  • Standard Horizon GM29 - page 251

    16. SUPPL EMENTARY SE RVICES 251 LZT 123 7361 R1A 16.13 AT +CHLD Cal l Hold and Mult ipart y This command al lows control of t he following ca ll related ser vices: • a call can be temporarily disconnected from the ME but the connection is retained by the network; • multiparty conversation (confer ence calls); • the served subscriber who has ...

  • Standard Horizon GM29 - page 252

    GM29 INTE GRATOR’S MANUAL 252 LZT 123 7 361 R1A “X” is the numbering (star ting with 1) of the call given by the se quence of setting up or r eceiving the call s (active, held or wa iting) as se en by the served subscriber . Calls hold their number until they are released. New calls take the low est available number . Where both a held and a ...

  • Standard Horizon GM29 - page 253

    16. SUPPL EMENTARY SE RVICES 253 LZT 123 7361 R1A Unsolicited Result c odes: +CLIP: <number>, <type>,,,<a lpha> Defined values: 16.15 AT +CLIR Calling Line I dentific ation Rest rictio n This command refers to CLIR-service according to GSM 02.81 that allows a calling subscriber to enable or disable the presentation of the CLI to t ...

  • Standard Horizon GM29 - page 254

    GM29 INTE GRATOR’S MANUAL 254 LZT 123 7 361 R1A revoke this adjustment. If this command is used by a subscriber without provision of CLIR in permanent mode the network will act a ccording GSM 02.81. The setting shall be per logical channel. When the MS is turned off and then turned on again the pa rameter setting <n> shall turn back to defa ...

  • Standard Horizon GM29 - page 255

    16. SUPPL EMENTARY SE RVICES 255 LZT 123 7361 R1A 16.16 AT +CSSN Supplement ary Servic e Notificat ion This command refers to supplementary service related network initiated notifications. The set command enables or disables the presentation of notification r esult codes from TA to TE. When <n>=1 and a supplementary ser vice notification is r ...

  • Standard Horizon GM29 - page 256

    GM29 INTE GRATOR’S MANUAL 256 LZT 123 7 361 R1A <m> Descr iption 0 Disable the +CSSU result c ode presentation status in t he TA 1 Enable the +CSSU result code pr esentation st atus in the TA <cod e1> Description 0 Unconditional call forwarding is active 1 Some of the conditional call forwarding are active 2 Call has been forwarded 3 ...

  • Standard Horizon GM29 - page 257

    16. SUPPL EMENTARY SE RVICES 257 LZT 123 7361 R1A 16.17 AT +CUSD Unstructure d Supplementar y Service Dat a This command allows control of the Unstructured Supplementary Service Data (USSD) according to GSM 02.90. Both network and mobile initiated operations are s upported. Parameter <n > is used to disable/enable the presentation of an unsol ...

  • Standard Horizon GM29 - page 258

    GM29 INTE GRATOR’S MANUAL 258 LZT 123 7 361 R1A The different alternatives are shown below. Example 1 Network Mobile Equipment External application 1 Sign al Sends unsolicited result code +CUSD Resul t code prese ntati on enabled , presented 2 Signal ask ing for reply Sends unsolicited result code +CUSD Resul t code prese ntati on enabled , prese ...

  • Standard Horizon GM29 - page 259

    16. SUPPL EMENTARY SE RVICES 259 LZT 123 7361 R1A Example 2 Example 3 AT Comm and Resu lt Code Description +CUSD:0,“Expensive incoming call” Incoming USSD-notify telling the user t hat th e incoming c all is expensive AT Comm and Result Code Description AT+CUS D=1,“*55 *0700#” Enable t he Result Code presen tation in the T AE and send a USS ...

  • Standard Horizon GM29 - page 260

    GM29 INTE GRATOR’S MANUAL 260 LZT 123 7 361 R1A ...

  • Standard Horizon GM29 - page 261

    261 LZT 123 7361 R1A 17. Alphabetical Listing of AT Commands AT Co mmand Descrip tio n Page No. AT Attent ion C ommand 131 AT&C Circu it 109 (DCD ) Control 135 AT&D Cir c uit 108 (DTR ) Respons e 135 AT&F Set to Factory Def ined Confi guration 131 AT&S Cir cuit 107 (DSR) R esponse 136 AT&W Store User Profile 131 AT* List all Sup ...

  • Standard Horizon GM29 - page 262

    GM29 INTE GRATOR’S MANUAL 262 LZT 123 7 361 R1A AT*EA LR Ericsson Audio Line Request 99 AT*EA LS Ericsson Request ALS St atus 153 AT*EA MS Ericsson Audio Mode Selection 100 AT*EA RS Ericsson Audio Ring Signal 101 AT*ECA M Ericsson Call Monitoring 74 AT*ECPI Ciphering Indicator 165 AT*ECSP E ricsson Customer Service P rofile 154 AT*ED IF Ericsson ...

  • Standard Horizon GM29 - page 263

    17. AL PHABETIC AL LISTING OF AT COMMAND S 263 LZT 123 7361 R1A AT+CCLK Set Clock and Date 77 AT+CCWA Call Waiting 249 AT+CEER Exten ded Error Report 77 AT+CF UN Set Ph one Function ality 78 AT+CG ACT PDP Cont ext Acti vate or Deac tivate 109 AT+CG ATT GPRS A t tach or Detach 110 AT+CG DATA Enter Data St ate 111 AT+CG DCONT Define PD P Conte xt 112 ...

  • Standard Horizon GM29 - page 264

    GM29 INTE GRATOR’S MANUAL 264 LZT 123 7 361 R1A AT+C MGC Send Command 191 AT+C MGD Delete Message 209 AT+C MGF Message Format 184 AT+C MGL List Message 203 AT+C MGR Read Message 198 AT+C MGS Send Message 187 AT+C MGW Write Message to Memory 184 AT+C MOD Call Mode 66 AT+C MSS Send From S torag e 190 AT+C MUX Switch to 07.10 Multiplex Protocol 139 ...

  • Standard Horizon GM29 - page 265

    17. AL PHABETIC AL LISTING OF AT COMMAND S 265 LZT 123 7361 R1A AT+CS MP Set T ext Mode Param eters 210 AT+CS MS Selec t Message Se rvice 212 AT+CS Q Sign al Strength 89 AT+CSSN Su pplem enta ry Servi ce Not ificati on 255 AT+CT ZU Automatic T ime Zone Update 90 AT+CU SD Unstructur ed Supplem entary Serv ice Data 257 AT+CV HU Voi ce Ha ng-U p 67 &q ...

  • Standard Horizon GM29 - page 266

    GM29 INTE GRATOR’S MANUAL 266 LZT 123 7 361 R1A ATT Select Tone Dialling 64 ATV DCE Response Format 137 ATX Call Progress Monitoring Control 65 ATZ Reset to Defa ult C onfigur ation 138 AT Comma nd Descr iption Page No. Unsolicited Resul t Code Description Pag e No. *E2STKE STK Send Short Message 230 *E2STKP STK S end SS 231 *E2STKR STK R efresh ...

Manufacturer Standard Horizon Category Modem

Documents that we receive from a manufacturer of a Standard Horizon GM29 can be divided into several groups. They are, among others:
- Standard Horizon technical drawings
- GM29 manuals
- Standard Horizon product data sheets
- information booklets
- or energy labels Standard Horizon GM29
All of them are important, but the most important information from the point of view of use of the device are in the user manual Standard Horizon GM29.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Standard Horizon GM29, service manual, brief instructions and user manuals Standard Horizon GM29. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Standard Horizon GM29.

Similar manuals

A complete manual for the device Standard Horizon GM29, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Standard Horizon GM29 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Standard Horizon GM29.

A complete Standard Horizon manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Standard Horizon GM29 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Standard Horizon GM29, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Standard Horizon GM29, that we can find in the current document
3. Tips how to use the basic functions of the device Standard Horizon GM29 - which should help us in our first steps of using Standard Horizon GM29
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Standard Horizon GM29
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Standard Horizon GM29 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Standard Horizon GM29?

Use the form below

If you did not solve your problem by using a manual Standard Horizon GM29, ask a question using the form below. If a user had a similar problem with Standard Horizon GM29 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)