English dropdown-ico

Manual Patton electronic 1080A

15 pages 0.13 mb
Download

Go to site of 15

Summary
  • Patton electronic 1080A - page 1

    USER MANUAL MODEL 1080A and MODEL 1080A-64 Universal Synchronous & Asynchronous Short Range Modems SALES OFFICE (301) 975-1000 TECHNICAL SUPPO R T (301) 975-1007 http://ww w .patton.com Part #07M1080A-D Doc. #072041UD Revised 6/19/98 CERTIFIED An ISO-9001 Certified Company ...

  • Patton electronic 1080A - page 2

    1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1080A Series components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unaut ...

  • Patton electronic 1080A - page 3

    2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected by Patton's qualified technicians. If any questions or problems arise during installation or use of this product, please do not hesitate to contact Patton Electronics T echnical Support at (301) 975-1007. 2.1 FEA ...

  • Patton electronic 1080A - page 4

    Each Model 1080A Series SRM has three sets of eight switches, yielding 24 total DIP switches. The three sets will be referred to as S1, S2 and S3. As Figure 2 shows, the orientation of all DIP switches is the same with respect to “ON” and “OFF” positions. 3.2 CONFIGURA TION SWITCH SET “S1” The DIP switches on S1 set data rate, clock sou ...

  • Patton electronic 1080A - page 5

    Switch S1-8: Carrier Control Method The setting for switch S1-8 determines whether the carrier is “constantly on” or “controlled by RTS”. This setting allows for operation in switched carrier , multipoint and/or hardware handshaking applications. S1-8 Setting Off Constantly on On Controlled by RTS 3.3 CONFIGURA TION SWITCH SET “S2” The ...

  • Patton electronic 1080A - page 6

    3.4 CONFIGURA TION SWITCH SET “S3” The DIP switches on S3 set the anti-stream control, local loopback enable, remote loopback enable and receive (input) impedance levels for the Model 1080A Series. Factory default positions of Switch S3 are shown in the table below . Switches S3-1 & S3-2: Input Impedance The setting for Switches S3-1 and S3 ...

  • Patton electronic 1080A - page 7

    Switch S3-6: RS-232 Initiation of Remote Loopback T est The setting for switch S3-6 determines whether or not the Model 1080A Series’ remote digital loopback test can be initiated by raising pin 21 on the RS-232 interface. S3-6 Setting On RS-232 initiation enabled Off RS-232 initiation disabled Switches S3-7 and S3-8: Anti-stream Control Switches ...

  • Patton electronic 1080A - page 8

    4.1.1 T wo-Wire Cable Connection Via RJ-45 A. The RJ-45 jack on a Model 1080A Series Short Range Modem is prewired for a standard TELCO wiring environment. T o be sure you have the right wiring, use the table below as a guide. RJ-45 SIGNAL 1 -------------NC 2 -------------GND † 3 -------------RCV 4 -------------XMT 5 -------------XMT 6 ---------- ...

  • Patton electronic 1080A - page 9

    4.2.1 Four-Wire Cable Connection Via RJ-45 A. The RJ-45 jack on a Model 1080A/1080A-64 Short Range Modem is prewired for a standard TELCO wiring environment. T o be sure you have the right wiring, use the table below as a guide. RJ-45 SIGNAL 1 -------------NC 2 -------------GND † 3 -------------RCV 4 -------------XMT 5 -------------XMT 6 -------- ...

  • Patton electronic 1080A - page 10

    4.3 FOUR-WIRE, MUL TIPOINT INST ALLA TION Multipoint operation involves the connection of several terminals to one host port. In such an application, one local Model 1080A/1080A-64 is used as a master unit, and it is connected to several remote Model 1080A/1080A-64s that are acting as slaves. Up to 25 Model 1080A Series slaves may be connected to o ...

  • Patton electronic 1080A - page 11

    5.1.4 The “Error” Indicators The “Error” indicator LED has three functions: A. When the 1080A Series unit is in test mode (green “T est” LED is lit), the error LED glows red when bit errors occur . B. When not in test mode (green “T est” LED is off), the error LED is used to indicate an RTS streaming condition. (See Section 5.2) for ...

  • Patton electronic 1080A - page 12

    5.1.4.2 Reading The T est A. If line quality is good, “Error” LED on local modem will not light and “CD” LED will be red. On remote modem “Error” LED will not light and “CD” LED will light green. B. If flat cable is used or parts of the line are flat cable, “Error” LED on local modem will light red and “CD” LED will light gr ...

  • Patton electronic 1080A - page 13

    A. Activate RDL. This may be done in two ways: First, by moving the front panel toggle switch UP to "Remote". Second, by raising pin 21 on the RS-232 interface (Note: Make sure DIP switch S3-6 is ON; and DIP switch S2-6 is OFF). B. Perform a BER (bit error rate) test on the system. C. If the BER test equipment indicates a fault, and the L ...

  • Patton electronic 1080A - page 14

    APPENDIX B P A TT ON MODEL 1080A SERIES F ACT OR Y REPLACEMENT P ARTS AND ACCESSORIES Patton Model # Description 080510ACB .....................120V W all Mount AC Adapter 08059ACI ........................230V AC Adapter (No Power Cord) 07M1080A .......................Model 1080A Series User Manual 25 APPENDIX C P A TT ON MODEL 1080A SERIES CABLE R ...

  • Patton electronic 1080A - page 15

    APPENDIX C P A TT ON MODEL 1080A SERIES INTERF ACE PIN ASSIGNMENT RS-232 FEMALE, D-SUB 25 CONNECTOR (DCE ORIENT A TION) 1- (FG) Frame Ground 2- (TD) T ransmit Data T o 1080A 3- (RD) Receive Data From 1080A 4- (RTS) Request to Send T o 1080A 5- (CTS) Clear to Send From 1080A 6- (DSR) Data Set Ready From 1080A 7- (SG) Signal Ground 8- (DCD) Data Carr ...

Manufacturer Patton electronic Category Network Card

Documents that we receive from a manufacturer of a Patton electronic 1080A can be divided into several groups. They are, among others:
- Patton electronic technical drawings
- 1080A manuals
- Patton electronic product data sheets
- information booklets
- or energy labels Patton electronic 1080A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Patton electronic 1080A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Patton electronic 1080A, service manual, brief instructions and user manuals Patton electronic 1080A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Patton electronic 1080A.

Similar manuals

A complete manual for the device Patton electronic 1080A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Patton electronic 1080A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Patton electronic 1080A.

A complete Patton electronic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Patton electronic 1080A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Patton electronic 1080A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Patton electronic 1080A, that we can find in the current document
3. Tips how to use the basic functions of the device Patton electronic 1080A - which should help us in our first steps of using Patton electronic 1080A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Patton electronic 1080A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Patton electronic 1080A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Patton electronic 1080A?

Use the form below

If you did not solve your problem by using a manual Patton electronic 1080A, ask a question using the form below. If a user had a similar problem with Patton electronic 1080A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)