-
Viper 650.2 - page 1
models 550.2 650.2 ...
-
Viper 650.2 - page 2
2 © 2002 Directed Electronics, Inc ...
-
Viper 650.2 - page 3
3 © 2002 Directed Electronics, Inc T ABLE OF CONTENTS CONGRA TULA TIONS Congratulations for choosing Viper Audio neodymium two-way component speakers from Directed Electronics. Directed Electronics has been the industr y leader in high-quality automo- tive security and audio equipment since 1990, and with the introduction of the Viper Audio line o ...
-
Viper 650.2 - page 4
4 © 2002 Directed Electronics, Inc LIMITED TWO-YEAR CONSUMER W ARRANTY Directed Electronics, Inc. (DEI) promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase from the dealer as indicated by the date code marking o ...
-
Viper 650.2 - page 5
5 © 2002 Directed Electronics, Inc High-powered car audio systems may produce sound pressure levels that exceed the threshold at which hearing loss may result. They may also impair a driver’ s ability to hear traffic sounds or emergency vehi- cles. Use common sense and practice safe listening habits when listening to or adjusting your audio syst ...
-
Viper 650.2 - page 6
6 © 2002 Directed Electronics, Inc INST ALLA TION PRECAUTIONS The Viper 550.2/650.2 neodymium separates are designed for installation into factor y speaker locations, custom mounting enclosures or any flat mounting surface inside the vehicle with sufficient rear clearance. The following precautions and instructions cover the basic and most common ...
-
Viper 650.2 - page 7
7 © 2002 Directed Electronics, Inc WOOFER INST ALLA TION Review the Installation Precautions section of this guide before proceeding. 1. Place the cutout template against the mounting surface in the desired location for the woofer . 2. Draw the speaker hole and mounting screw locations on the panel with a marker . The 550.2 woofer requires a 4 ...
-
Viper 650.2 - page 8
8 © 2002 Directed Electronics, Inc TWEETER INST ALLA TION Review the Installation Precautions section of this guide before proceeding. Flush Mounting into Removed Panels 1. Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. 2. Mark the center point of the tweeter location. 3. If using a hole s ...
-
Viper 650.2 - page 9
9 © 2002 Directed Electronics, Inc Flush Mounting into Mounted Panels 1. Determine the tweeter mounting location, then route the wires from the crossover to the tweeter loca- tion. 2. Mark the center point of the tweeter location. 3. If using a hole saw , first drill a pilot hole, then cut out the hole using a standard 2-1/8" hole saw . 4. If ...
-
Viper 650.2 - page 10
10 © 2002 Directed Electronics, Inc T weeter Surface Mounting 1. Deter mine the tweeter mounting location, then route the wires from the crossover to the tweeter loca- tion. 2. Place the sur face mount housing against the panel and mark the two holes at the rear of the housing. 3. Drill the smaller center hole using a 1/8" drill bit. This is ...
-
Viper 650.2 - page 11
11 © 2002 Directed Electronics, Inc CROSSOVER INST ALLA TION Review the Installation Precautions section of this guide before proceeding. Crossover Adjustment and Wiring Connections This Viper crossover has the ability to work in car audio systems from basic single amplifier systems to the most sophisticated multiple amplifier systems with signal ...
-
Viper 650.2 - page 12
12 © 2002 Directed Electronics, Inc FIGURE 5—SINGLE AMPLIFIER Connection/Adjustment Single Amplifier 1. Connect the amplifier channel output to the crossover input connector as shown, carefully obser ving amplifier output polarity . 2. Connect the tweeter and woofer wires to the output connector as shown, carefully obser ving speaker polarity . ...
-
Viper 650.2 - page 13
13 © 2002 Directed Electronics, Inc FIGURE 6—DUAL AMPLIFIER Connection/Adjustment Dual Amplifier 1. Connect the amplifier tweeter and woofer channel outputs to the crossover input connector as shown, carefully obser ving amplifier output polarity . 2. Connect the tweeter and woofer wires to the output connector as shown, carefully obser ving spe ...
-
Viper 650.2 - page 14
14 © 2002 Directed Electronics, Inc SPECIFICA TIONS Viper model 550.2 650.2 T weeter Fs (Hz) 71.1 51.7 1534.54 V as (cu.ft.) 0.19 0.63 n/a V as (L) 5.5 17.9 n/a Qms 7.19 5.91 1.16 Qes 0.50 0.45 2.76 Qts 0.47 0.42 0.82 Re (ohms) 3.8 3.8 3.36 Z (ohms) 4 4 4 Le (mh) 0.49 0.483 0.01 SPL (dB 1w@1m) 87.86 89.29 91 XMAX (inches) 0.2 0.2 0.02 XMAX (mm) 4. ...
-
Viper 650.2 - page 15
...
-
Viper 650.2 - page 16
16 © 2002 Directed Electronics, Inc The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security , car stereo products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of advanced electroni ...
Do you have a question concerning Viper 650.2?
Use the form below
If you did not solve your problem by using a manual Viper 650.2, ask a question using the form below. If a user had a similar problem with Viper 650.2 it is likely that he will want to share the way to solve it.