English dropdown-ico

Manual Garmin GNS 430

168 pages 3.86 mb
Download

Go to site of 168

Summary
  • Garmin GNS 430 - page 1

    GNS 430 Shown GARMIN International, Inc. 1200 E. 151 st Street Olathe, KS 66062 USA 190-00140-05, Revision C October 2002 400 SERIES MAINTENANCE MANUAL (GNS ¥ 430, GNC ¥ 420, GPS 400) ...

  • Garmin GNS 430 - page 2

    Page A 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 © Copyright 1999-2002 GARMIN Ltd. or its subsidiaries All Rights Reserved GARMIN International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. GARMIN (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ, U.K. GARMIN Corporation No. 68, Jangshu 2 ...

  • Garmin GNS 430 - page 3

    400 SERIES MAINTENANCE MANUAL Page i P/N 190-00140-05 Rev. C LIST OF EFFECTIVE PAGES Page Revision Page Revision Page Revision Page Revision A C 4-8 C 5-54 BLANK F7-24 BLANK i C 5-1 C 6-1 C A-1 C i i C5 - 2 C6 - 2 CA - 2 C i i i C5 - 3 C6 - 3 CB - 1 C i v C5 - 4 C6 - 4 CB - 2 C v C 5-5 C 6-5 C B-3 C v i C5 - 6 C6 - 6 CB - 4 C vii C 5-7 C 6-7 C B-5 ...

  • Garmin GNS 430 - page 4

    Page ii 400 SERIES MAINTENANCE MANUAL P/N 190-00140-05 Rev. C The following are General Safety Precautions that are not related to any specific procedure and therefore do not appear elsewhere in this maintenance manual. These are recommended precautions that personnel should understand and apply during the many phases of maintenance and repair. KEE ...

  • Garmin GNS 430 - page 5

    400 SERIES MAINTENANCE MANUAL Page iii P/N 190-00140-05 Rev. C TABLE OF CONTENTS SECTION 1 DESCRIPTION AND OPERATION Paragraph Page 1.1 INTRODUCTION .................................................................................................... 1-1 1.1.1 Versions Covered by this Manual .......................................................... ...

  • Garmin GNS 430 - page 6

    Page iv 400 SERIES MAINTENANCE MANUAL P/N 190-00140-05 Rev. C SECTION 3 TROUBLESHOOTING Paragraph Page 3.1 TROUBLESHOOTING EQUIPMENT ..................................................................... 3-1 3.2 TROUBLESHOOTING ORDER .............................................................................. 3-1 3.3 TROUBLESHOOTING PROCEDURES ... ...

  • Garmin GNS 430 - page 7

    400 SERIES MAINTENANCE MANUAL Page v P/N 190-00140-05 Rev. C SECTION 5 ALIGNMENT, CALIBRATION, AND TESTING Paragraph Page 5.1 INTRODUCTION ................................................................................................. 5-1 5.2 RECOMMENDED TEST EQUIPMENT ............................................................... 5-1 5.3 TEST S ...

  • Garmin GNS 430 - page 8

    Page vi 400 SERIES MAINTENANCE MANUAL P/N 190-00140-05 Rev. C SECTION 5 ALIGNMENT, CALIBRATION, AND TESTING (continued) 5.7.2.8 Sidetone ........................................................................................................ 5-18 5.7.2.9 MIC Intercom Test ............................................................................. ...

  • Garmin GNS 430 - page 9

    400 SERIES MAINTENANCE MANUAL Page vii P/N 190-00140-05 Rev. C SECTION 5 ALIGNMENT, CALIBRATION, AND TESTING (continued) 5.7.4 Navigation Assembly I/O Tests .................................................................... 5-32 5.7.4.1 Localizer Course Deviation Test ................................................................... 5-32 5.7.4. ...

  • Garmin GNS 430 - page 10

    Page viii 400 SERIES MAINTENANCE MANUAL P/N 190-00140-05 Rev. C SECTION 5 ALIGNMENT, CALIBRATION, AND TESTING (continued) 5.7.6.14 MAIN Vertical UP, DOWN Outputs................................................................ 5-47 5.7.6.15 MAIN To/From Output ................................................................................... 5-47 5 ...

  • Garmin GNS 430 - page 11

    400 SERIES MAINTENANCE MANUAL Page ix P/N 190-00140-05 Rev. C APPENDIX A GNC 420A AND GNS 430A A.1 DESCRIPTION ....................................................................................................A-1 A.2 ‘A’ VERSION PART NUMBERS ..........................................................................A-1 A.3 TROUBLESHOOTING .... ...

  • Garmin GNS 430 - page 12

    Page x 400 SERIES MAINTENANCE MANUAL P/N 190-00140-05 Rev. C LIST OF FIGURES Figure Page 2-1 Com Chassis Nut ................................................................................................. 2-1 2-2 Signal And Load Drawing-J1 (Sheet 1 of 2) ........................................................ 2-3 2-3 Signal And Load Drawing-J1 ( ...

  • Garmin GNS 430 - page 13

    400 SERIES MAINTENANCE MANUAL Page xi P/N 190-00140-05 Rev. C LIST OF TABLES Table Page 1-1 Unit Configuration ................................................................................................ 1-1 3-1 Unit Board Power Supply Max Current Allowed .................................................. 3-5 3-2 Com Board Power Supply Toleranc ...

  • Garmin GNS 430 - page 14

    Page xii 400 SERIES MAINTENANCE MANUAL P/N 190-00140-05 Rev. C LIST OF TABLES (con’t.) Table Page 6-25 Sub-Assy, CDU, GNC 420, Black (Unit P/N 011-00281-01, Figure 7-4) ........... 6-23 6-26 Sub-Assy, CDU, GNC 420, Gray (Unit P/N 011-00281-05, Figure 7-4) ............ 6-24 6-27 Sub-Assy, CDU GNC 420A, Black (Unit P/N 011-00281-01, Figure 7-4) ... ...

  • Garmin GNS 430 - page 15

    400 SERIES MAINTENANCE MANUAL Page 1-1 P/N 190-00140-05 Rev. C SECTION 1 DESCRIPTION AND OPERATION 1.1 INTRODUCTION References made to the GNS 430 and the GNC 420 throughout this manual equally apply to the GNS 430A and the GNC 420A except where specifically noted. This manual provides board-level maintenance inform ation for the GARMIN 400 Series ...

  • Garmin GNS 430 - page 16

    Page 1-2 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 GPS 400: UNIT P/N COLOR 011-00504-00 Black 011-00504-10 Gray GNC 420: UNIT P/N COLOR OPERATING VOLTAGE MINIMUM XMIT PWR 011-00506-00 BLACK 28 V 10 W 011-00506-10 BLACK 14 or 28 V 10 W 011-00506-30 GRAY 14 or 28 V 10 W GNS 430: UNIT P/N COLOR OPERATING VOLTAGE MINIMUM XMIT PWR 011-00280- ...

  • Garmin GNS 430 - page 17

    400 SERIES MAINTENANCE MANUAL Page 1-3 P/N 190-00140-05 Rev. C Each of the configurations includes a color display providing graphical moving map capability. Navigation, communication, and m apping functions are supported by a navigation database provided by a removable database card. The mapping function has additional support provided by a built- ...

  • Garmin GNS 430 - page 18

    Page 1-4 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 1.3 REPAIR PLAN This manual is designed to allow the user to perform board-level repair. If necessary, the unit can be returned to GARMIN for complete service work. Contact GARMIN at the address given on Page A (inside cover) for further service information. 1.4 SPECIFICATIONS Technical ...

  • Garmin GNS 430 - page 19

    400 SERIES MAINTENANCE MANUAL Page 1-5 P/N 190-00140-05 Rev. C 1.5.2 Com Board The Com Board contains the VHF COM Transceiver that provides voice comm unication in the 118.000 to 136.992 MHz general aviation band. The transceiver consists of a 10 or 16 watt (“A” versions) amplitude modulated transm itter (see the unit matrix tables on page 1-1) ...

  • Garmin GNS 430 - page 20

    Page 1-6 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 1.5.5 Glideslope Board The Glideslope Board contains a processor controlled Glideslope Receiver which operates from 329.15 MHz to 335.00 MHz in 150 kHz increments for 40 Glideslope channels. 1.5.6 Inverter Board The Inverter Board supplies high voltage for display operation. 1.5.7 CDU A ...

  • Garmin GNS 430 - page 21

    400 SERIES MAINTENANCE MANUAL Page 2-1 P/N 190-00140-05 Rev. C SECTION 2 SPECIAL TOOLS AND TEST EQUIPMENT 2.1 INTRODUCTION This section identifies the special tools and test equipment needed to maintain the 400 Series Units. Standard equipment is not listed. For any questions regarding special tools and test equipment contact GARMIN at the followin ...

  • Garmin GNS 430 - page 22

    Page 2-2 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 This page left intentionally blank. ...

  • Garmin GNS 430 - page 23

    400 SERIES MAINTENANCE MANUAL Page 2-3 (Page 2-4 blank) P/N 190-00140-05 Rev. C Figure 2-2. J1 Signal and Load Drawing (Sheet 1 of 2) ...

  • Garmin GNS 430 - page 24

    400 SERIES MAINTENANCE MANUAL Page 2-5 (Page 2-6 blank) P/N 190-00140 Rev. C Figure 2-3. J1 Signal and Load Drawing (Sheet 2 of 2) ...

  • Garmin GNS 430 - page 25

    400 SERIES MAINTENANCE MANUAL Page 2-7 (Page 2-8 blank) P/N 190-00140-05 Rev. C Figure 2-4. J2 Signal and Load Drawing ...

  • Garmin GNS 430 - page 26

    400 SERIES MAINTENANCE MANUAL Page 2-9 (Page 2-10 blank) P/N 190-00140-05 Rev. C Figure 2-5. J6 Signal and Load Drawing ...

  • Garmin GNS 430 - page 27

    400 SERIES MAINTENANCE MANUAL Page 3-1 P/N 190-00140-05 Rev. C SECTION 3 TROUBLESHOOTING Each unit in the 400 Series contains static sensitive components. Observe proper anti-static procedures when testing the unit. Hazardous voltages exist on the Inverter Board (all units). Under normal operating conditions the voltages range up to 2500 Vac peak t ...

  • Garmin GNS 430 - page 28

    Page 3-2 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 3.3 TROUBLESHOOTING PROCEDURES 3.3.1 Fuses Check for blown fuses on the Main Board, Com Board, and Nav Board as shown in Figures 3-1 through 3-4. If blown fuses are found, try to determine the cause of the fuse failure before installing a new fuse. F 8 5 0 5A F853 0.75A F851 3A F852 2A ...

  • Garmin GNS 430 - page 29

    400 SERIES MAINTENANCE MANUAL Page 3-3 P/N 190-00140-05 Rev. C LOCA TION OF F600 (7A FUSE ) ON -00/-02/-03 COM BOARDS Figure 3-2. Com Board Fuse Location/F600 LOCATION OF F600 ON -04 REV C COM BOARDS TO PRES ENT (F600 REPLACED WITH R611, EXCEPT ON -0 4 REV A AND B BOARD) Figure 3-3. Com Board Fuse Location/F600 (Replaced by R611) ...

  • Garmin GNS 430 - page 30

    Page 3-4 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 F501 1 AMP J6 F502 1 AMP Figure 3-4. Nav Board Fuse Locations 3.3.2 Power Supply Checks 3.3.2.1 Current Measurements Taking intra-board and external current measureme nts is one way of determining a faulty board. To measure the currents, use a spare ribbon cable and spread the cable wir ...

  • Garmin GNS 430 - page 31

    400 SERIES MAINTENANCE MANUAL Page 3-5 P/N 190-00140-05 Rev. C The values listed in Table 3-1 are with the display backlight at maximum brightness. Table 3-1. Unit Board Power Supply Max Current Allowed Unit (Main Board) Unit Status Max Current (A) @ 27.5 V Max Current (A) @ 13.8 V (Optional) GPS 400 ON 0.66 1.32 GNC 420 ON RX—0.99 TX—3.36 RX? ...

  • Garmin GNS 430 - page 32

    Page 3-6 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 3.3.2.3 Glideslope Board Replace the Main Board if any voltage on the G/S Board is not within tolerance. Replace the G/S Board if excessive current is measured. Table 3-3. Glideslope Board Power Supply Tolerances Connector/Pin Voltage (V) Tolerance (V) Max Current (mA) Comments J25 Pin ...

  • Garmin GNS 430 - page 33

    400 SERIES MAINTENANCE MANUAL Page 3-7 P/N 190-00140-05 Rev. C I - 111 0 I-1 00 Figure 3-5. Processor Location (Main Board) 3.4 STATIC MESSAGES The unit informs the user of operational status using the messages listed in Table 3-5. These messages can help in isolating a faulty assembly. Table 3-5 also shows the recommended action for each message. ...

  • Garmin GNS 430 - page 34

    Page 3-8 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 3-5. Static Messages MESSAGE RECOMMENDED ACTION Stored data was lost Replace Main Board (see paragraph 4.5.5) Main processor requires service Replace Main Board (see paragraph 4.5.5) Memory battery low Replace Memory Battery (see paragraph 4.7.1) No differential GPS position Repla ...

  • Garmin GNS 430 - page 35

    400 SERIES MAINTENANCE MANUAL Page 3-9 P/N 190-00140-05 Rev. C Table 3-5. Static Messages (continued) COM remote transfer key stuck Verify that Remote Transfer Key Line is not stuck before replacing COM Board Replace Com Board (see paragraph 4.5.4) Heading input failure Replace Main Board (see paragraph 4.5.5) CDI key stuck Replace Flex Cable (see ...

  • Garmin GNS 430 - page 36

    Page 3-10 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 3.5 TESTING FAILURES Another approach in troubleshooting is to perform testing on a unit according to the test procedures given in Section 5. To save time, only perform the minim um amount of testing in order to isolate the suspect board. Table 3-6 lists recommended actions based on fa ...

  • Garmin GNS 430 - page 37

    400 SERIES MAINTENANCE MANUAL Page 3-11 P/N 190-00140-05 Rev. C Table 3-6. Testing Failures  Main Board (continued) TEST FAILURE TEST PARAGRAPH RECOMMENDED ACTION GPS Antenna Bias 5.7.6.10 Replace GPS Module (see paragraph 4.5.5) GPS Noise 5.7.6.11 Replace GPS Module (see paragraph 4.5.5) Replace Main Board (see paragraph 4.5.5) Satellite Tracki ...

  • Garmin GNS 430 - page 38

    Page 3-12 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 3-7. Testing Failures  COM Board TEST FAILURE TEST PARAGRAPH RECOMMENDED ACTION Power Input Check 5.7.2.1 Replace Main Board (see paragraph 4.5.5) Replace Com Board (see paragraph 4.5.4) RF Power Out 5.7.2.2 Replace Com Board (see paragraph 4.5.4) Frequency Stability and Toler ...

  • Garmin GNS 430 - page 39

    400 SERIES MAINTENANCE MANUAL Page 3-13 P/N 190-00140-05 Rev. C Table 3-8. Testing Failures  NAV Board TEST FAILURE TEST PARAGRAPH RECOMMENDED ACTION Localizer Course Deviation Test 5.7.4.1 Replace Nav Receiver Board (see paragraph 4.5.6) To/From Deflection Output Characteristic Test 5.7.4.2 Replace Nav Receiver Board (see paragraph 4.5.6) To/Fr ...

  • Garmin GNS 430 - page 40

    Page 3-14 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 3-10. Testing Failures  NAV Receiver TEST FAILURE TEST PARAGRAPH RECOMMENDED ACTION Voice/Ident Audio Output Level 5.7.3.1 Replace Nav Receiver Board (see paragraph 4.5.6) Voice/Ident Audio Frequency Response 5.7.3.2 Replace Nav Receiver Board (see paragraph 4.5.6) Voice/Ident ...

  • Garmin GNS 430 - page 41

    400 SERIES MAINTENANCE MANUAL Page 3-15 P/N 190-00140-05 Rev. C 3.6 EXTERNAL CONNECTORS Figure 3-6 shows the external connectors and their corresponding pin numbers for each unit. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 1 2 34 5 67 89 10 11 12 14 15 16 17 18 19 20 21 ...

  • Garmin GNS 430 - page 42

    Page 3-16 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 This page left intentionally blank. ...

  • Garmin GNS 430 - page 43

    400 SERIES MAINTENANCE MANUAL Page 3-17 (Page 3-18 blank) P/N 190-00140-05 Rev. C Figure 3-7. 400 Series Block Diagarm ...

  • Garmin GNS 430 - page 44

    400 SERIES MAINTENANCE MANUAL Page 4-1 P/N 190-00140-05 Rev. C SECTION 4 DISASSEMBLY AND ASSEMBLY 4.1 INTRODUCTION Repairing the unit is accomplished by removing and replacing defective boards. To help disassemble and reassemble the unit in order to access the boards, look at the assembly drawings in Section 7 and the parts lists in Section 6. Each ...

  • Garmin GNS 430 - page 45

    Page 4-2 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 4.3 NAV DATA CARD REMOVAL AND INSERTION Before disassembly begins, remove the Jeppesen NavData® card supplied with the unit. The card can be installed or removed when the unit is on or off. Insert the card with the swing arm handle at the bottom and the label facing to the left (see Fi ...

  • Garmin GNS 430 - page 46

    400 SERIES MAINTENANCE MANUAL Page 4-3 P/N 190-00140-05 Rev. C 4.4 UNIT DESIGN Each unit consists of a Main and Nav Chassis, CDU Assembly, and a Top Cover. The Main Chassis has a Top and Underside Cavity which contains replaceable boards. The following is a typical order of disassembly: 1. Remove the Top Cover. 2. Remove the CDU Assembly. 3. Disass ...

  • Garmin GNS 430 - page 47

    Page 4-4 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 4.5.2.1 Disassemble the CDU Assembly x Remove the Flex Assemblies (Figure 7-4) 1. Remove the VOL w/’C’ and VOL w/’V’ Knobs (18 and 19). 2. Remove the Push ‘CRSR’ and Push ‘C/V’ knobs (21, 22, 20, and 28). 3. Remove the Hex Nuts holding the Push ‘CRSR’ and Push ‘C/V ...

  • Garmin GNS 430 - page 48

    400 SERIES MAINTENANCE MANUAL Page 4-5 P/N 190-00140-05 Rev. C 4.5.4 Remove Faulty Boards from the Main Chassis Top Cavity Remove the Top Cover (see paragraph 4.5.1) to access the Main Chassis Top Sub-assemblies. x COM Board (Figure 7-2) Steps 5 and 6 apply to 28V/10W units only. 14/28V and 28V/16W units have no posistor, no brass spacers, and use ...

  • Garmin GNS 430 - page 49

    Page 4-6 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 x GPS Module (Figure 7-2) 1. Disconnect the Ribbon Cable from the GPS Module (011-00474-XX). 2. Remove screw (211-60234-11) attaching the Map Board (012-00296-00) to the Main Chassis (125-00034-01). Remove 3 of 5 screws (211-63234-10) attaching GPS Module (011-00474-XX) to the Main Chas ...

  • Garmin GNS 430 - page 50

    400 SERIES MAINTENANCE MANUAL Page 4-7 P/N 190-00140-05 Rev. C x Glideslope Board (Figure 7-3) 1. Remove the Glideslope Board Cover (115-00221-00). 2. Disconnect the Ribbon Cable (325-00063-01) from the Glideslope Board (012- 00212-XX). 3. Unsolder the connector wire from the Coax Connector (330-00070-03). 4. Remove the three screws (211-60234-04) ...

  • Garmin GNS 430 - page 51

    Page 4-8 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 1. Remove the Main Board (paragraph 4.5.5). 2. Remove all electrical grounds from the unit, so if using a grounded tip soldering iron, the battery will not be shorted upon removal. 3. Unsolder the battery leads from the bottom side of the Main Board. 4. Carefully remove the battery by p ...

  • Garmin GNS 430 - page 52

    400 SERIES MAINTENANCE MANUAL Page 5-1 P/N 190-00140-05 Rev. C SECTION 5 ALIGNMENT, CALIBRATION, AND TESTING 5.1 INTRODUCTION This section provides unit-level alignment, calibration, and testing information for the 400 Series units. The procedures in this section can be performed before troubleshooting begins to help identify a faulty board, or as ...

  • Garmin GNS 430 - page 53

    Page 5-2 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05  Avionics Signal Generator  IFR or Marconi 2030 w/options one and six.  BF Goodrich Precision Track Selector  Digital Voltmeter—HP 34401A  GPS Antenna—GARMIN GA56 (P/N 010-10040-01)  Power Supply capable of 10-33 Volts @ 10 Amps—HP 6267B  Radio Test Set—HP 8 ...

  • Garmin GNS 430 - page 54

    400 SERIES MAINTENANCE MANUAL Page 5-3 P/N 190-00140-05 Rev. C UNIT UNDER TEST BIRD WA TT M E T E R 30 dB 50 W A TT A TTENUA TOR 50 OHM LOAD RF INPUT AT T E N U AT E D RF OUTPUT NOTE 5 0 O H M L O A D IS N O T R E Q U IR E D I F 30 dB A T TE N U A TO R I S U S ED . THE 30 dB A TTE NU A TOR W I LL L OWE R T H E V S WR T O < 1 . 1 : 1 EVEN I F L E ...

  • Garmin GNS 430 - page 55

    Page 5-4 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.4.1.2 Standard Signals  COM RF Level Units All specifications given for the com transceiver are in HARD units. To arrive at these units adjust the RF generator to the level specified and insert a 6 dB pad at the output of the RF generator.  Standard Mic Input Signal A 1000 Hz to ...

  • Garmin GNS 430 - page 56

    400 SERIES MAINTENANCE MANUAL Page 5-5 P/N 190-00140-05 Rev. C  Standard Glideslope Centering Test Signal Standard Glideslope centering test signal is a standard Glideslope test signal in which the difference in depth of modulation of the 90 and 150 Hz signals is less than 0.002 ddm.  Standard Glideslope Deviation Test Signal Standard Glidesl ...

  • Garmin GNS 430 - page 57

    Page 5-6 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05  G/S Super Flag Load (G/S SUPER FLAG OUT) One standard super flag load shall be 56 ohms connected between G/S SUPER FLAG OUT J6-38 and GND J6-41.  ARINC 429 Transmitter Load (VLOC 429 OUTA/OUTB) The standard ARINC 429 transmitter load shall be 2.4K ohms resistance and 250 pF capac ...

  • Garmin GNS 430 - page 58

    400 SERIES MAINTENANCE MANUAL Page 5-7 P/N 190-00140-05 Rev. C  Standard VOR Audio Test Signal Standard VOR audio test signal is a standard VOR test signal to which is added a 1000 Hz signal, amplitude modulating the carrier 30%.  Standard Audio Test Signal Standard audio test signal is a RF carrier amplitude modulated 30% at 1000 Hz. The RF ...

  • Garmin GNS 430 - page 59

    Page 5-8 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05  Standard Localizer Centering Test Signal Standard localizer centering test signal is a standard localizer test signal in which the difference in depth of modulation of the 90 and 150 Hz signals is less than 0.001.  Standard Localizer Deviation Test Signal Standard localizer devia ...

  • Garmin GNS 430 - page 60

    400 SERIES MAINTENANCE MANUAL Page 5-9 P/N 190-00140-05 Rev. C 5.5 ALIGNMENT Board alignment is not recommended on any of the 400 Series units. Alignment is performed on individual boards at the factory before being shipped as replacement items. 5.6 CALIBRATION Calibration can be performed for the following:  COM Frequency  Frequency Spacing ...

  • Garmin GNS 430 - page 61

    Page 5-10 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.6.1 Com Setup Page Fields 5.6.1.1 Com Frequency The Com Frequency field selects a VHF communication frequency. For purposes of setting the squelch, sidetone levels and mic gain, only the frequencies 118.000, 127.000, and 136.975 MHz can be used. If any adjustment is made at one of th ...

  • Garmin GNS 430 - page 62

    400 SERIES MAINTENANCE MANUAL Page 5-11 P/N 190-00140-05 Rev. C 5.6.1.5 Sidetone The sidetone audio output level is independent of the COM volume knob on the unit. The SIDETN field sets the sidetone audio output level. The sidetone can be set to any value between zero and 63. The higher the number, the greater the sidetone volume.  SIDETN ______ ...

  • Garmin GNS 430 - page 63

    Page 5-12 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7 TEST PROCEDURES 5.7.1 Test Mode In order to perform certain tests in the following section, the GNS 430 must be put into test m ode, which allows access to the Test Pages (Figure 5-4). To put the unit in the test mode, ground Test Pin (J1-76) and turn the unit on. When in test mode ...

  • Garmin GNS 430 - page 64

    400 SERIES MAINTENANCE MANUAL Page 5-13 P/N 190-00140-05 Rev. C Figure 5-4. Test Pages ...

  • Garmin GNS 430 - page 65

    Page 5-14 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.2 Com Testing Before starting com testing, note the following: 1. Disable the audio compressor unless otherwise specified. The compressor can be disabled for testing purposes by manually grounding the SQUELCH/COMPRESSOR TEST input at Pin 3 of J2 . 2. The 8.33 kHz channel mode uses ...

  • Garmin GNS 430 - page 66

    400 SERIES MAINTENANCE MANUAL Page 5-15 P/N 190-00140-05 Rev. C 3. Transmit Mode: +14/+28 Volt Radios (J2-11 and 12):  Voltage _________ (+ 13.75 V)  Tolerance _________ ( r 0.2 V)  Max Current Avg 1 _________ (6.0 A) 5.7.2.2 RF Power Out 1. Set input voltage to 27.5 VDC (10 W, 28V units only) in TX mode at Pins J2-11 and 12. 2. Connect a ...

  • Garmin GNS 430 - page 67

    Page 5-16 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Figure 5-5. Modulation Measurement Figure 5-5 shows the output of the Narda Crystal Detector display ed on an oscilloscope. The oscilloscope must be DC coupled in order for the modulation signal to be displayed correctly. 5.7.2.3 Frequency Stability and Tolerance Verify the RF carrier ...

  • Garmin GNS 430 - page 68

    400 SERIES MAINTENANCE MANUAL Page 5-17 P/N 190-00140-05 Rev. C 5.7.2.5 Carrier Noise Level 1. Apply a standard MIC input signal. 2. The demodulated noise on the transmitter output, without audio m odulation, shall be at least 45 dB below the demodulated audio level obtained when the transmitter is m odulated with a standard mic input signal.  1 ...

  • Garmin GNS 430 - page 69

    Page 5-18 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.2.8 Sidetone 1. Apply a standard mic input signal. Measure com audio out and while transmitting, verify sidetone level is 1.4 Vrms  0.2 Vrms.  118.50 MHz ______ Vrms  127.50 MHz ______ Vrms  136.50 MHz ______ Vrms 5.7.2.9 MIC Intercom Test 1. Remove RF input from the un ...

  • Garmin GNS 430 - page 70

    400 SERIES MAINTENANCE MANUAL Page 5-19 P/N 190-00140-05 Rev. C 5.7.2.11 TX Interlock 1. Apply an 10 P V, 30% modulated, 1000 Hz RF signal. 2. Measure SNR at rated audio ( a 7.07 Vrms).  Sensitivity Reading 1______ 3. Enable TX interlock line. 4. Measure SNR again.  Sensitivity Reading 2______  NLT 15dB difference between sensitivity readi ...

  • Garmin GNS 430 - page 71

    Page 5-20 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 7. Adjust the RF level to 20 µV. 8. Verify the DMM reading is greater than the AGC reference voltage.  DMM reading ________VDC (NLT AGC Reference Voltage) 9. Adjust the signal generator frequency to 127.008 MHz. 10. Verify the DMM reading is greater than the reference AGC voltage. ...

  • Garmin GNS 430 - page 72

    400 SERIES MAINTENANCE MANUAL Page 5-21 P/N 190-00140-05 Rev. C 11. Verify the DMM reading is greater than the reference AGC voltage.  127.002778 MHz ______VDC (NLT AGC reference voltage)  126.997222 MHz ______VDC (NLT AGC reference voltage) 12. Adjust signal level to 10 mV.  127.00737 MHz ______VDC (NGT AGC reference voltage)  126.9926 ...

  • Garmin GNS 430 - page 73

    Page 5-22 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.2.17 Audio Frequency Response 1. With compression disabled, apply a 30% modulated, 1 mV signal to the unit. 2. Verify the audio output does not change more than 6 dB from 350 Hz to 2.5 kHz. 3. Verify the audio-frequency response above 2500 Hz decreases, and at all frequencies above ...

  • Garmin GNS 430 - page 74

    400 SERIES MAINTENANCE MANUAL Page 5-23 P/N 190-00140-05 Rev. C 5.7.2.19 Squelch Test Note: Opened squelch—Audio Closed Squelch—No Audio 1. Enable compressor (see Section 5.7.2). 2. Set the unit and the RF signal generator to 127.000 MHz, 30% modulated with a 1 kHz tone. 3. Turn the RF level down below 1µV. 4. Turn the power/volume control on ...

  • Garmin GNS 430 - page 75

    Page 5-24 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.2.20 Frequency Modulation FM deviation is to be measured with an average responding detector, which is RMS sine wave calibrated. The result is to be divided by 0.707 to yield the mathematical peak deviation. 1. Modulate the transmitter with a standard modulator input signal. 2. Ver ...

  • Garmin GNS 430 - page 76

    400 SERIES MAINTENANCE MANUAL Page 5-25 P/N 190-00140-05 Rev. C 5.7.3 Navigation Receiver Final Tests 5.7.3.1 Voice/Ident Audio Output Level 1. Apply a standard audio test signal having a RF level of -93 dBm. 2. Select maximum audio (volume control turned fully clockwise), and turn off the ident filter. 3. Measure 500 : VOR/ILS AUDIO HI J6-16 with ...

  • Garmin GNS 430 - page 77

    Page 5-26 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.3.3 Voice/Ident Audio Distortion 1. Apply an input level from the RF generator of -79 dBm. 2. Modulate a standard VOR audio test signal at 350 Hz, 1000 Hz, and 2500 Hz (must be in IDENT mode to pass 1000 Hz tone). 3. Measure 500 : VOR/ILS AUDIO HI J6-16 with respect to 500 : VOR/IL ...

  • Garmin GNS 430 - page 78

    400 SERIES MAINTENANCE MANUAL Page 5-27 P/N 190-00140-05 Rev. C 5.7.3.6 Receiver Quieting 1. Apply a -86 dBm RF level to the RF input. 2. Apply a Standard VOR Audio Test signal at 108.00 MHz. 3. Measure at the 500 : VOR/ILS AUDIO HI J6-16 and 500 : VOR/ILS AUDIO LO J6-17 outputs. 4. Verify the Audio SINAD or SNR is greater than 25 dB.  Audio SIN ...

  • Garmin GNS 430 - page 79

    Page 5-28 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.3.9 VOR Flag Sensitivity A VOR/LOC +FLAG output voltage of greater than 260 mV fully conceals the indicator flag (‘HIDE’) and a VOR/LOC +FLAG output voltage of less than 125 m V fully reveals the indicator flag (IN VIEW). This test requires a Precision Track Selector or similar ...

  • Garmin GNS 430 - page 80

    400 SERIES MAINTENANCE MANUAL Page 5-29 P/N 190-00140-05 Rev. C 5.7.3.12 VOR Course Deviation Sensitivity 1. Apply a standard VOR deviation signal at 108.00 MHz, –103.5 dBm RF level to the RF input. at a radial of 160 degrees ‘FROM’. 2. Apply a Precision Test Selector or similar device at 150 degrees in course angle. 3. Measure at the VOR/LOC ...

  • Garmin GNS 430 - page 81

    Page 5-30 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.3.16 Course Deviation Accuracy Test Apply a standard localizer deviation test signal, 90 Hz greater than 150Hz. Verify the deviation measured at VOR/LOC +LEFT with respect to VOR/LOC +RIGHT (VOR/LOC COMMON) is 90 mV r 9 m V. _____OK 5.7.3.17 VOR OBS Bearing Accuracy 1. Apply a stan ...

  • Garmin GNS 430 - page 82

    400 SERIES MAINTENANCE MANUAL Page 5-31 P/N 190-00140-05 Rev. C 5.7.3.19 Spurious Response—VOR/LOC 1. Tune the VOR receiver to 117.95 MHz. 2. Verify the input signal level of an undesired image frequency of 77.15 MHz required to produce a detector-carrier (AGC) level obtained at the VOR/LOC IF AGC J6-7 output with a -93 dBm Standard VOR Audio Tes ...

  • Garmin GNS 430 - page 83

    Page 5-32 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.4 Navigation Assembly I/O Tests 5.7.4.1 Localizer Course Deviation Test 1. Display the VOR/LOC/GS CDI Test Page (Figure 5-6). Figure 5-6. VOR/LOC/GS CDI Test Page 2. Display the following on the VOR/LOC/GS CDI Test Page and verify the following voltages, measuring across VOR/LOC +L ...

  • Garmin GNS 430 - page 84

    400 SERIES MAINTENANCE MANUAL Page 5-33 P/N 190-00140-05 Rev. C 6. Verify the following output:  TO/FROM (VOR/LOC +TO) ______(-225 r 75 mV) 7. Display HIDE. 8. Measure VOR/LOC +TO (J6-1) with respect to VOR/LOC +FROM (J6-2). 9. Verify the following output:  TO/FROM (VOR/LOC +TO) ______ mV (0 mV r 5 mV) 5.7.4.4 Course Deviation Flag Output Cha ...

  • Garmin GNS 430 - page 85

    Page 5-34 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5. Verify the VOR/LOC SUPER FLAG OUT output voltage with respect to ground is 0 r 250 mV (50 ohm load).  VOR/LOC SUPER FLAG OUT ______ mV 5.7.4.7 NAV Input Lines Monitor the “VOR DISCRETE INPUTS” Test Page and verify that toggling the below listed inputs between their active and ...

  • Garmin GNS 430 - page 86

    400 SERIES MAINTENANCE MANUAL Page 5-35 P/N 190-00140-05 Rev. C 5.7.4.9 NAV Serial DME Outputs Monitor the “VOR DISCRETE OUTPUTS” Test Page and verify that toggling the below listed outputs between their active and inactive states causes the output voltage on the appropriate line to switch between low (<.01 V) and high (>8.0 V) states. ? ...

  • Garmin GNS 430 - page 87

    Page 5-36 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05  PAR DME 2 MHz Low____ High ____ (Input Switch must not be grounded for this test)  PAR DME 4 MHz Low____ High ____ (Input Switch must not be grounded for this test)  PAR DME 8 MHz Low____ High ____ ...

  • Garmin GNS 430 - page 88

    400 SERIES MAINTENANCE MANUAL Page 5-37 P/N 190-00140-05 Rev. C 5.7.5 Glideslope Final Tests 5.7.5.1 Glideslope Course Deviation Output Characteristic Test 1. Apply a standard course deviation input signal to the unit. 2. Measure GLIDESLOPE +UP (J6-32) with respect to GLIDESLOPE +DOWN (J6-31). 3. Verify the deviation output voltages (GLIDESLOPE +UP ...

  • Garmin GNS 430 - page 89

    Page 5-38 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.5.4 Glideslope Superflag Output Test 1. Select flag ‘HIDDEN’. 2. Verify GLIDESLOPE superflag output voltage is not less than PWR_IN minus 1.5 V.  GLIDESLOPE Superflag Output ______ (NLT Power_IN minus 1.5 V) 3. Select Flag ‘IN VIEW’. 4. Verify GLIDESLOPE superflag output ...

  • Garmin GNS 430 - page 90

    400 SERIES MAINTENANCE MANUAL Page 5-39 P/N 190-00140-05 Rev. C 5.7.5.6 Centering Accuracy 1. Apply a standard glideslope test signal to the unit. 2. Measure GLIDESLOPE +UP (J6-32) with respect to GLIDESLOPE +DOWN (GLIDESLOPE Common) (J6-31). 3. Verify the centering accuracy is 0 mV r 7.8 mV.  Centering Accuracy _________mV 5.7.5.7 AGC 1. Apply ...

  • Garmin GNS 430 - page 91

    Page 5-40 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.5.9 Nose Bandwidth 1. Apply standard glideslope test signal to the unit (-56dBm). 2. Find the AGC voltage and use it as a reference. 3. Vary the input signal frequency over the range of r 17 kHz from the assigned channel frequency. 4. Verify the input signal level needed to maintai ...

  • Garmin GNS 430 - page 92

    400 SERIES MAINTENANCE MANUAL Page 5-41 P/N 190-00140-05 Rev. C 5.7.5.12 Status Tests 1. The following status bits shall be good with or without a standard glideslope test signal:  GLIDESLOPE ROM_______OK  GLIDESLOPE EEPROM _____OK  GLIDESLOPE Synthesizer Lock__________OK 2. The following status bits shall be good when a standard glideslop ...

  • Garmin GNS 430 - page 93

    Page 5-42 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.6 Main Board Final Tests GNC 420 versions 011-00506-10 or 011-00506-30, and GNS 430 versions 011-00280-10 or 011-00280-30 m ust be verified operational with dual power switch in both positions (1 and 2). The “A” versions of the GNC 420 and the GNS 430 must be verified also. See ...

  • Garmin GNS 430 - page 94

    400 SERIES MAINTENANCE MANUAL Page 5-43 P/N 190-00140-05 Rev. C 5.7.6.4 Photocell 1. Turn the unit on in the test mode and verify brightness control is in photo mode, using the main lighting page. 2. With photocell uncovered, ensure display and keyboard backlight LED brightness is proper under normal conditions. _____OK 3. Cover the photocell and v ...

  • Garmin GNS 430 - page 95

    Page 5-44 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Figure 5-7. Main Lighting and Main Analog Test Pages B. Lighting Bus DC 1. Using the Main Lighting Test Page, change source to 14 VDC in both the DISPLAY and KEY fields. 2. Attach 12.0 VDC to unit pin J1-39. Ensure the power supply ground is connected to unit ground (J1-77, 78). 3. Mon ...

  • Garmin GNS 430 - page 96

    400 SERIES MAINTENANCE MANUAL Page 5-45 P/N 190-00140-05 Rev. C 5.7.6.7 Display Pattern Test Starting from the display pattern test page, use the “RNG” buttons to cycle through all of the display patterns to verify all pixels are driven and color contrast is acceptable. _____OK 5.7.6.8 Fan Test 1. Verify fan blade is not moving or air is not be ...

  • Garmin GNS 430 - page 97

    Page 5-46 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 1. Put the unit into Test Mode. 2. Turn the small right knob (CRSR) until you see the GPS Test Page (Figure 5-7). 3. Terminate GPS receiver into a 50 ohm load. 4. The “sgnl” number represents the receiver noise level. Verify this number is within the range of 1450 to 1750. _____OK ...

  • Garmin GNS 430 - page 98

    400 SERIES MAINTENANCE MANUAL Page 5-47 P/N 190-00140-05 Rev. C Figure 5-9. Main CDI/OBS Configuration Test Page 5.7.6.13 MAIN Lateral LEFT, RIGHT Outputs Measure J1-21 (output) relative to J1-22 (output) [Load—333 ohms (three 1000 ohm loads) across J1-21 and J1-22]. Note that full left/right ( r 150 m V) are also available selections but are not ...

  • Garmin GNS 430 - page 99

    Page 5-48 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.6.16 MAIN Lateral Flag Output Measure J1-23 relative to J1-24. Load—333 ohms (Three 1000 ohm loads) across J1-23 and J1-24.  ‘HIDE’______ (+375 r 80 mV)  IN VIEW ______ (0 r 25 mV ) 5.7.6.17 MAIN Vertical Flag Output Measure J1-29 relative to J1-30. Load—333 ohms (Thr ...

  • Garmin GNS 430 - page 100

    400 SERIES MAINTENANCE MANUAL Page 5-49 P/N 190-00140-05 Rev. C 5.7.6.20 Annunciate Outputs Both the OBS and the AUTO outputs are switched by toggling the OBS selection on the Test Page. For: ANNUCIATOR PIN NAV (VLOC) (J1-1) GPS (J1-2) WAYPOINT (J1-3) TERMINAL (A) (J1-4) APPROACH (B) (J1-5) MESSAGE (J1-6) OBS (J1-7) AUTO (J1-8) INTEGRITY (C) (J1-9) ...

  • Garmin GNS 430 - page 101

    Page 5-50 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 2. Measure at applicable pin. Load—Resistor to external voltage source such that it will source 275 mA when grounded. Note: applicable output will sink this current when active (18 ohms/2W when pulled up to 5V).  ACTIVE______ (0.3 VDC max)  INACTIVE ______ (NLT pull-up voltage ...

  • Garmin GNS 430 - page 102

    400 SERIES MAINTENANCE MANUAL Page 5-51 P/N 190-00140-05 Rev. C 5.7.6.22 Discrete Switch and Altitude Inputs For: INPUT NAME PIN ALTITUDE C4 (J1-61) ALTITUDE C2 (J1-62) ALTITUDE C1 (J1-63) ALTITUDE B4 (J1-64) ALTITUDE B2 (J1-65) ALTITUDE B1 (J1-66) ALTITUDE A4 (J1-67) ALTITUDE A2 (J1-68) ALTITUDE A1 (J1-69) ALTITUDE D4 (J1-70) OBS MODE SELECT (J1-7 ...

  • Garmin GNS 430 - page 103

    Page 5-52 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.6.23 ARINC 429 Transmitter and Receivers Unit outputs both HIGH and LOW speed signals at the same time in test mode while on the Main Status/Loopback Test Page, thus both speeds are tested simultaneously. For: GPS ARINC 429 OUT A (J1-46). GPS ARINC 429 OUT B (J1-47). GPS ARINC 429 ...

  • Garmin GNS 430 - page 104

    400 SERIES MAINTENANCE MANUAL Page 5-53 P/N 190-00140-05 Rev. C 5.7.6.24 RS232 Ports For: GPS RS232 OUT 1 (J1-56) GPS RS232 IN 1 (J1-57) GPS RS232 OUT 2 (J1-58) GPS RS232 IN 2 (J1-59) GPS RS232 OUT 3 (J1-41) GPS RS232 IN 3 (J1-42) GPS RS232 OUT 4 (J1-54) GPS RS232 IN 4 (J1-55) A. GPS RS232 1 1. Test both receiver and transmitter. 2. Connect the tra ...

  • Garmin GNS 430 - page 105

    Page 5-54 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 5.7.6.25 OBS The load used in the OBS test consists of a calibrated OBS resolver, Precision Track Selector or equivalent, and must be connected to the GPS OBS inputs. The OBS bearing must be consistent to within r 2 degrees of the bearing setting. If this output requires an alignment, ...

  • Garmin GNS 430 - page 106

    400 SERIES MAINTENANCE MANUAL Page 6-1 P/N 190-000140-05 Rev. C SECTION 6 PARTS AND ASSEMBLIES 6.1 INTRODUCTION This section lists major parts of the 400 Series. The part numbers listed in this section of the manual are given to aid in assembly and disassembly of the unit only, not for identifying orderable parts. For orderable part information, se ...

  • Garmin GNS 430 - page 107

    Page 6-2 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 GNC420/420A Table Part Description Unit P/N Figure 6-15 Sub-Assy, GNC420, 28V, Black 011-00506-00 7-5 6-16 Sub-Assy, GNC420, 14/28V, Black 011-00506-10 7-5 6-17 Sub-Assy, GNC420, 14/28V, Gray 011-00506-30 7-5 6-18 Sub-Assy, GNC420A, 28V, Black 011-00837-00 7-8 6-19 Sub-Assy, GNC420A, 28 ...

  • Garmin GNS 430 - page 108

    400 SERIES MAINTENANCE MANUAL Page 6-3 P/N 190-000140-05 Rev. C Miscellaneous Parts Part Part Description Unit P/N Figure F600 Fuse, Submini, Axial, 7 Amp 350-00003-15 3-2 F850 Fuse, SMT, Fast, 5 Amp 350-B0500-01 3-1 F853 Fuse, 1206, 0.75 Amp 350-B1075-00 3-1 F852 Fuse, 1206, 2 Amp 350-B1200-00 3-1 F851 Fuse, 1206, 3 Amp 350-B1300-00 3-1 R611 Resis ...

  • Garmin GNS 430 - page 109

    Page 6-4 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 6.2.1 GNS 430/430A Tables Table 6-1. Sub-Assy, GNS 430, 28V, Black (Unit P/N 011-00280-00, Figure 7-1) Part Number Part Name Qty 011-00281-00 Sub-Assy,CDU,GNS430 1 011-00282-00 Sub-Assy,Nav Chassis,GNC400 1 011-00283-00 Sub-Assy,Main Chas,GNS430,28V 1 011-00460-40 Sub-Assy,Memory Card,D ...

  • Garmin GNS 430 - page 110

    400 SERIES MAINTENANCE MANUAL Page 6-5 P/N 190-000140-05 Rev. C Table 6-3. Sub-Assy, GNS 430, 14/28V, Gray (Unit P/N 011-00280-30, Figure 7-1) Part Number Part Name Qty 011-00281-04 Sub-Assy,CDU,GNS430,Gray 1 011-00282-00 Sub-Assy,Nav Chassis,GNC400 1 011-00283-30 Sub,Mn Chassis,GNS430,14/28V,DO 1 011-00460-40 Sub-Assy,Memory Card,Dummy 1 115-00218 ...

  • Garmin GNS 430 - page 111

    Page 6-6 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-5. Sub-Assy GNS 430A, 28V, Gray (Unit P/N 011-00836-10, Figure 7-1) Part Number Part Name Qty 011-00281-04 Sub-Assy,CDU,GNS430,Gray 1 011-00282-00 Sub-Assy,Nav Chassis,GNC400 1 011-00283-20 Sub,Main Chassis,GNS430A 1 011-00460-40 Sub-Assy,Memory Card,Dummy 1 115-00218-00 SMP,Cov ...

  • Garmin GNS 430 - page 112

    400 SERIES MAINTENANCE MANUAL Page 6-7 P/N 190-000140-05 Rev. C Table 6-6. Main Chassis Assy, GNS 430, 14/28V (Unit P/N 011-00283-10, Figure 7-2) Part Number Part Name Qty 011-00474-01 Sub-Assy,GPS Module,GNC TSOII 1 012-00214-05 PCB Assy,Comm,10W 14/28V 1 012-00256-00 PCB Assy,GNC400 Inverter Bd 1 012-00296-00 PCB Assy,GNC400 Map Bd 1 012-00347-32 ...

  • Garmin GNS 430 - page 113

    Page 6-8 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-7. Main Chassis Assy, GNS 430, 14/28V, DO (Unit P/N 011-00283-30, Fig. 7-2) Part Number Part Name Qty 011-00474-01 Sub-Assy,GPS Module,GNC TSOII 1 012-00214-05 PCB Assy,Comm,10W 14/28V 1 012-00256-00 PCB Assy,GNC400 Inverter Bd 1 012-00296-00 PCB Assy,GNC400 Map Bd 1 012-00347-3 ...

  • Garmin GNS 430 - page 114

    400 SERIES MAINTENANCE MANUAL Page 6-9 P/N 190-000140-05 Rev. C Table 6-8. Main Chassis Assy, GNS 430, 28V (Unit P/N 011-00283-00, Fig. 7-2) Part Number Part Name Qty 011-00474-01 Sub-Assy,GPS Module,GNC TSOII 1 012-00214-03 PCB Assy,Comm,2.5ppm TCXO 1 012-00256-00 PCB Assy,GNC400 Inverter Bd 1 012-00296-00 PCB Assy,GNC400 Map Bd 1 012-00347-32 PCB ...

  • Garmin GNS 430 - page 115

    Page 6-10 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-9. Main Chassis Assy, GNS 430A, 28V (Unit P/N 011-00283-20, Figure 7-2) Part Number Part Name Qty 011-00474-01 Sub-Assy,GPS Module,GNC TSOII 1 012-00256-00 PCB Assy,GNC400 Inverter Bd 1 012-00296-00 PCB Assy,GNC400 Map Bd 1 012-00347-32 PCB Assy,GNS430 Main Bd,DO 1 012-00611-00 ...

  • Garmin GNS 430 - page 116

    400 SERIES MAINTENANCE MANUAL Page 6-11 P/N 190-000140-05 Rev. C Table 6-10. Nav Chassis Sub-Assy, GNS 430/430A (Unit P/N 011-00282-00, Figure 7-3) Part Number Part Name Qty 012-00195-20 PCB Assy,Nav Rcvr,GNC400/500 1 012-00212-10 PCB Assy,GNC400 Glide Slope 1 115-00209-00 SMP,Cover,Cont,GNC400 Nav Bd 1 115-00213-00 SMP,Cover,RF,GNC400 Nav Bd 1 115 ...

  • Garmin GNS 430 - page 117

    Page 6-12 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-11. Sub-Assy, CDU, GNS 430, Black (Unit P/N 011-00281-00, Figure 7-4) Bub Part Number Part Name Qty 1 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 6 210-00021-00 Nut,Hex,Reduced 1 7 211-00030-00 Pivot Pin,Power Switch 1 8 117-00028-00 Shaft,Pot,Machined,GNC4XX 1 20 430-00013-01 ...

  • Garmin GNS 430 - page 118

    400 SERIES MAINTENANCE MANUAL Page 6-13 P/N 190-000140-05 Rev. C Table 6-12. Sub-Assy, CDU, GNS 430, Gray (Unit P/N 011-00281-04, Figure 7-4) Bub Part Number Part Name Qty 1 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 6 210-00021-00 Nut,Hex,Reduced 1 7 211-00030-00 Pivot Pin,Power Switch 1 8 117-00028-00 Shaft,Pot,Machined,GNC4XX 1 20 430-00013-01 ...

  • Garmin GNS 430 - page 119

    Page 6-14 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-13. Sub-Assy, CDU, GNS 430A, Black (Unit P/N 011-00281-00, Figure 7-4) Bub Part Number Part Name Qty 1 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 6 210-00021-00 Nut,Hex,Reduced 1 7 211-00030-00 Pivot Pin,Power Switch 1 8 117-00028-00 Shaft,Pot,Machined,GNC4XX 1 20 430-00013-01 ...

  • Garmin GNS 430 - page 120

    400 SERIES MAINTENANCE MANUAL Page 6-15 P/N 190-000140-05 Rev. C Table 6-14. Sub-Assy, CDU, GNS 430A, Gray (Unit P/N 011-00281-04, Figure 7-4) Bub Part Number Part Name Qty 1 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 6 210-00021-00 Nut,Hex,Reduced 1 7 211-00030-00 Pivot Pin,Power Switch 1 8 117-00028-00 Shaft,Pot,Machined,GNC4XX 1 20 430-00013-01 ...

  • Garmin GNS 430 - page 121

    Page 6-16 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 6.2.3 GNC 420/420A Tables Table 6-15. Sub-Assy, GNC 420, 28V, Black (Unit P/N 011-00506-00, Figure 7-5) Part Number Part Name Qty 011-00281-01 Sub-Assy,CDU,GNC420 1 011-00282-01 Sub-Assy,Nav Chassis,w/o Nav 1 011-00283-01 Sub-Assy,Main Chas,GNC420,28V 1 011-00460-40 Sub-Assy,Memory Car ...

  • Garmin GNS 430 - page 122

    400 SERIES MAINTENANCE MANUAL Page 6-17 P/N 190-000140-05 Rev. C Table 6-17. Sub-Assy, GNC 420, 14/28V, Gray (Unit P/N 011-00506-30, Figure 7-5) Part Number Part Name Qty 011-00281-05 Sub-Assy,CDU,GNC420,Gray 1 011-00282-01 Sub-Assy,Nav Chassis,w/o Nav 1 011-00283-31 Sub,Mn Chassis,GNC420,Gray,DO 1 011-00460-40 Sub-Assy,Memory Card,Dummy 1 115-0021 ...

  • Garmin GNS 430 - page 123

    Page 6-18 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-19. Sub-Assy, GNC 420A, 28V Gray (Unit P/N 011-00837-10, Figure 7-8) Part Number Part Name Qty 011-00281-05 Sub-Assy,CDU,GNC420,Gray 1 011-00282-01 Sub-Assy,Nav Chassis,w/o Nav 1 011-00283-21 Sub,Main Chassis,GNC420A 1 011-00460-40 Sub-Assy,Memory Card,Dummy 1 115-00218-00 SMP, ...

  • Garmin GNS 430 - page 124

    400 SERIES MAINTENANCE MANUAL Page 6-19 P/N 190-000140-05 Rev. C Table 6-20. Main Chassis Assy, GNC 420, 28V (Unit P/N 011-00283-01, Figure 7-6) Part Number Part Name Qty 011-00474-01 Sub-Assy,GPS Module,GNC TSOII 1 012-00214-03 PCB Assy,Comm,2.5ppm TCXO 1 012-00256-00 PCB Assy,GNC400 Inverter Bd 1 012-00296-00 PCB Assy,GNC400 Map Bd 1 012-00347-22 ...

  • Garmin GNS 430 - page 125

    Page 6-20 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-21. Main Chassis Assy, GNC 420, 14/28V (Unit P/N 011-00283-11, Fig. 7-6) Part Number Part Name Qty 011-00474-01 Sub-Assy,GPS Module,GNC TSOII 1 012-00214-05 PCB Assy,Comm,10W 14/28V 1 012-00256-00 PCB Assy,GNC400 Inverter Bd 1 012-00296-00 PCB Assy,GNC400 Map Bd 1 012-00347-22 ...

  • Garmin GNS 430 - page 126

    400 SERIES MAINTENANCE MANUAL Page 6-21 P/N 190-000140-05 Rev. C Table 6-22. Main Chassis Assy, GNC 420, 14/28V, DO, (P/N 011-00283-31, Figure 7-6) Item Description Qty 011-00474-01 Sub-Assy,GPS Module,GNC TSOII 1 012-00214-05 PCB Assy,Comm,10W 14/28V 1 012-00256-00 PCB Assy,GNC400 Inverter Bd 1 012-00296-00 PCB Assy,GNC400 Map Bd 1 012-00347-22 PC ...

  • Garmin GNS 430 - page 127

    Page 6-22 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-23. Main Chassis Sub-Assy, GNC 420A, 28V (Unit P/N 011-00283-21, Figure 7-6) Part Number Part Name Qty 011-00474-01 Sub-Assy,GPS Module,GNC TSOII 1 012-00611-00 PCB Assy,Comm Xcvr,16 Watt 1 012-00256-00 PCB Assy,GNC400 Inverter Bd 1 012-00296-00 PCB Assy,GNC400 Map Bd 1 012-003 ...

  • Garmin GNS 430 - page 128

    400 SERIES MAINTENANCE MANUAL Page 6-23 P/N 190-000140-05 Rev. C Table 6-25. Sub-Assy, CDU, GNC 420, Black (Unit P/N 011-00281-01, Figure 7-4) Bub Number Item Description Qty 32 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 28 430-00013-01 Knob Assy,Outer,GNC400/500 1 20 430-00013-01 Knob Assy,Outer,GNC400/500 1 1 011-00340-00 Sub-Assy,Inc Dec Push S ...

  • Garmin GNS 430 - page 129

    Page 6-24 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-26. Sub-Assy, CDU, GNC 420, Gray (Unit 011-00281-05, Figure 7-4) Bub Number Part Number Part Name Qty 32 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 28 430-00013-01 Knob Assy,Outer,GNC400/500 1 20 430-00013-01 Knob Assy,Outer,GNC400/500 1 1 011-00340-00 Sub-Assy,Inc Dec Push Sw ...

  • Garmin GNS 430 - page 130

    400 SERIES MAINTENANCE MANUAL Page 6-25 P/N 190-000140-05 Rev. C Table 6-27. Sub-Assy, CDU, GNC 420A, Black (Unit P/N 011-00281-01, Figure 7-4) Bub Number Item Description Qty 32 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 28 430-00013-01 Knob Assy,Outer,GNC400/500 1 20 430-00013-01 Knob Assy,Outer,GNC400/500 1 1 011-00340-00 Sub-Assy,Inc Dec Push ...

  • Garmin GNS 430 - page 131

    Page 6-26 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-28. Sub-Assy, CDU, GNC 420A, Gray (Unit 011-00281-05, Figure 7-4) Bub Number Part Number Part Name Qty 32 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 28 430-00013-01 Knob Assy,Outer,GNC400/500 1 20 430-00013-01 Knob Assy,Outer,GNC400/500 1 1 011-00340-00 Sub-Assy,Inc Dec Push S ...

  • Garmin GNS 430 - page 132

    400 SERIES MAINTENANCE MANUAL Page 6-27 P/N 190-000140-05 Rev. C 6.2.4 GPS 400 Tables Table 6-29. Sub-Assy, GPS 400, 14/28V, Black (Unit P/N 011-00504-00, Figure 7-10) Part Number Part Name Qty 011-00281-03 Sub-Assy,CDU,GPS400 1 011-00282-01 Sub-Assy,Nav Chassis,w/o Nav 1 011-00283-33 Sub,Main Chassis,GPS400,DO 1 011-00460-40 Sub-Assy,Memory Card,D ...

  • Garmin GNS 430 - page 133

    Page 6-28 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-31. Main Chassis Assy, GPS 400 14/28V, (Unit P/N 011-00283-03, Figure 7-9) Part Number Part Name Qty 011-00474-01 Sub-Assy,GPS Module,GNC TSOII 1 012-00256-00 PCB Assy,GNC400 Inverter Bd 1 012-00296-00 PCB Assy,GNC400 Map Bd 1 012-00347-02 PCB Assy,GPS400 Main Bd,DO 1 115-00337 ...

  • Garmin GNS 430 - page 134

    400 SERIES MAINTENANCE MANUAL Page 6-29 P/N 190-000140-05 Rev. C Table 6-34. Sub-Assembly, CDU, GPS 400, Black (Unit P/N 011-00281-03), Fig 7-4) Bub Part Number Part Name Qty 1 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 2 211-60232-06 Screw,2-56x.187,PHP,SS/P,w/NYL 6 3 410-00012-01 Rtry Sw,Pot,w/Mom Push Sw, 1 5 012-00258-00 PCB Assy,GNC400 Interf ...

  • Garmin GNS 430 - page 135

    Page 6-30 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table 6-35. Sub-Assembly, CDU, GPS 400, Gray (Unit P/N 011-00281-06, Fig 7-4) Bub Part Number Part Name Qty 1 011-00340-00 Sub-Assy,Inc Dec Push Switch 1 2 211-60232-06 Screw,2-56x.187,PHP,SS/P,w/NYL 6 3 410-00012-01 Rtry Sw,Pot,w/Mom Push Sw, 1 5 012-00258-00 PCB Assy,GNC400 Interface ...

  • Garmin GNS 430 - page 136

    400 SERIES MAINTENANCE MANUAL Page 7-1 P/N 190-00140-05 Rev. C SECTION 7 ASSEMBLY DRAWINGS 7.1 INTRODUCTION This section contains assembly drawings to aid in assembly and disassembly of the 400 Series units. Part numbers and drawing notes can be used as reference information during disassem bly and assembly. Note: The revision levels of the drawing ...

  • Garmin GNS 430 - page 137

    Page 7-2 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 GPS 400: x GPS 400 Assy Drawing (Dwg. No. 015-00504-XX, Rev. G, Figure 7-10) x Figure 7-9—Main Chassis Assembly, GPS 400 (Dwg. No. 015-00283-03, Rev. J) x GPS 400 Sub-Assy, Nav Chassis, W/O Nav (Use Figure 7-7) x GPS 400 CDU Assembly Drawing (Use Figure 7-4) ...

  • Garmin GNS 430 - page 138

    400 SERIES MAINTENANCE MANUAL Page 7-3 (page 7-4 blank) P/N 190-00140-05 Rev. C Figure 7-1. Sub-Assy, GNS 430 (Dwg. No. 015-00280-XX, Rev. P) ...

  • Garmin GNS 430 - page 139

    400 SERIES MAINTENANCE MANUAL Page 7-5 (page 7-6 blank) P/N 190-00140-05 Rev. C Figure 7-2. Main Chassis Assy, GNS 430(A) (Dwg. No. 015-00283-00, Rev. R) ...

  • Garmin GNS 430 - page 140

    400 SERIES MAINTENANCE MANUAL Page 7-7 (page 7-8 blank) P/N 190-00140-05 Rev. C Figure 7-3. Nav Chassis Assy, GNC 400 (Dwg. No. 015-00282-00, Rev. K) ...

  • Garmin GNS 430 - page 141

    400 SERIES MAINTENANCE MANUAL Page 7-9 (Page 7-10 blank) P/N 190-00140-05 Rev. C Figure 7-4. GNC 4XX CDU Assy (Sheet 1 of 2) (Dwg. No. 015-00281-XX, Rev. F ) ...

  • Garmin GNS 430 - page 142

    400 SERIES MAINTENANCE MANUAL Page 7-11 (Page 7-12 blank) P/N 190-00140-05 Rev. C Figure 7-4. GNC 4XX CDU Assy (Sheet 2 of 2) (Dwg. No. 015-00281-XX, Rev. F ) ...

  • Garmin GNS 430 - page 143

    400 SERIES MAINTENANCE MANUAL Page 7-13 (page 7-14 blank) P/N 190-00140-05 Rev. C Figure 7-5. Sub-Assy, GNC 420 (Dwg. No. 015-00506-XX, Rev. N) ...

  • Garmin GNS 430 - page 144

    400 SERIES MAINTENANCE MANUAL Page 7-15 (page 7-16 blank) P/N 190-00140-05 Rev. C Figure 7-6. Main Chassis Assy, GNC 420(A) (Dwg. No. 015-00283-01, Rev. K) ...

  • Garmin GNS 430 - page 145

    400 SERIES MAINTENANCE MANUAL Page 7-17 (page 7-18 blank) P/N 190-00140-05 Rev. C Figure 7-7. Nav Chassis Assy, W/O Nav (Dwg. No. 015-00282-01, Rev. E) ...

  • Garmin GNS 430 - page 146

    400 SERIES MAINTENANCE MANUAL Page 7-19 (page 7-20 blank) P/N 190-00140-05 Rev. C Figure 7-8. Sub-Assy, GNC 420A (Dwg. No. 015-00837-XX, Rev. A) ...

  • Garmin GNS 430 - page 147

    400 SERIES MAINTENANCE MANUAL Page 7-21 (page 7-22 blank) P/N 190-00140-05 Rev. C Figure 7-9. Main Chassis Assy, GPS 400 (Dwg. No. 015-00283-03, Rev. J) ...

  • Garmin GNS 430 - page 148

    400 SERIES MAINTENANCE MANUAL Page 7-23 (Page 7-24 blank) P/N 190-00140-05 Rev. C Figure 7-10. Assy Dwg, GPS 400 (Dwg. No. 015-00504-XX, Rev. G) ...

  • Garmin GNS 430 - page 149

    400 SERIES MAINTENANCE MANUAL Page A-1 P/N 190-00140-05 Rev. C APPENDIX A GNC 420A AND GNS 430A A.1 DESCRIPTION This appendix describes version A of the GNC 420 and the GNS 430. The ‘A’ versions contain a 16 watt VHF Com Transmitter as opposed to a 10 watt transm itter. There is one Com Board part number for the GNC 420 and GNS 430 ‘A’ vers ...

  • Garmin GNS 430 - page 150

    Page A-2 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 The Com Voltage and Current requirements for the GNS 420A and GNS 430A are listed in Table A-2. Table A-2. Voltage and Current Supply Requirements Connector / Pin DC Voltage Tolerance(V) Max Current (DC) Conditions J2, Pins 11 & 12 +27.5 r .4 3.0 A Transmit Mode A.4 DISASSEMBLY AND ...

  • Garmin GNS 430 - page 151

    400 SERIES MAINTENANCE MANUAL Page B-1 P/N 190-00140-05 Rev. C APPENDIX B CONNECTOR I/O DESCRIPTIONS B.1 I/O DESCRIPTION This appendix contains tables describing various I/O information used in the 400 Series. Table B-1. I/O Descriptions IO Code Description I INPUT O OUTPUT B BI-DIRECTIONAL B.2 INTERNAL AND EXTERNAL CONNECTORS Table B-2. Internal a ...

  • Garmin GNS 430 - page 152

    Page B-2 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table B-2. Internal and External Connections (continued) INVERTER BOARD J13 Main Board J26 Display Module CCTF J27 Display Module Heater GPS MODULE ( ALL UNITS) J101 J3 Main Board Antenna In INTERFACE BOARD J19 Data Card Flex J20 Left Data Card J21 Right Data Card DISPLAY MODULE J22 LCD ...

  • Garmin GNS 430 - page 153

    400 SERIES MAINTENANCE MANUAL Page B-3 P/N 190-00140-05 Rev. C Table B-3. J1 Descriptions (continued) AIRCRAFT POWER 20 I MAIN +LEFT 21 O MAIN +RIGHT (2.5V Common) 22 O MAIN LATERAL +FLAG 23 O MAIN LATERAL -FLAG (2.5V Common) 24 O MAIN +TO 25 O MAIN +FROM (2.5V Common) 26 O MAIN +UP 27 O MAIN +DOWN (2.5V Common ) 28 O MAIN VERTICAL +FLAG 29 O MAIN ...

  • Garmin GNS 430 - page 154

    Page B-4 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table B-3. J1 Descriptions (continued) GPS RS232 IN4 55 I GPS RS232 OUT1 56 O GPS RS232 IN1 57 I GPS RS232 OUT2 58 O GPS RS232 IN2 59 I ALTITUDE COMMON (Ground) 60 O ALTITUDE C4 61 I ALTITUDE C2 62 I ALTITUDE C1 63 I ALTITUDE B4 64 I ALTITUDE B2 65 I ALTITUDE B1 66 I ALTITUDE A4 67 I AL ...

  • Garmin GNS 430 - page 155

    400 SERIES MAINTENANCE MANUAL Page B-5 P/N 190-00140-05 Rev. C B.3.3 J9 Table B-5. J9 Descriptions Pin Name Pin # I/O Description 12V 1 O 12 volt Supply to NAV board and G/S board from Main CPU board. 5V_NAV 2 O +5 volt Supply to NAV board and G/S board from Main CPU board. GND 3 O Ground. -12V 4 O -12 volt Supply to NAV board and G/S board from Ma ...

  • Garmin GNS 430 - page 156

    Page B-6 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 B.3.5 J12 Table B-7. J12 Descriptions Pin Name Pin # I/O Description LD1 through LD8 46-50 3-5 O LOWER half display DATA output. CLK_ROW 6 O Pulse high for typically 310 ns at a period of 33.236 us (30.088 kHz). This line loads the next row of data in the display drivers. There are 66 C ...

  • Garmin GNS 430 - page 157

    400 SERIES MAINTENANCE MANUAL Page B-7 P/N 190-00140-05 Rev. C Table B-7. J12 Descriptions (continued) NOT USED 25 ROT_R_LRGA ROT_R_LRGB ROT_R_LRGC 64 26 27 I I I Rotor Right Large A to C are the contacts of a single pole triple throw switch. The common of the switch is ground. Only one of the 3 is low at a time. ROT_R_SMLA ROT_R_SMLB ROT_R_SMLC 61 ...

  • Garmin GNS 430 - page 158

    Page B-8 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 Table B-8. J14 Descriptions (continued) 36 37 38 ROT_L_SMLC ROT_L_SMLB ROT_L_SMLA I I I Rotor Left Small A to C are the contacts of a single pole triple throw switch. The common of the switch is ground. Only one of the 3 is low at a time. 39 ROT_L_SW I Push switch on left rotary. Active ...

  • Garmin GNS 430 - page 159

    400 SERIES MAINTENANCE MANUAL Page B-9 P/N 190-00140-05 Rev. C B.3.7 J16 Table B-9. J16 Descriptions Pin Name Pin # I/O Description CS_MAPN 1 O Chip Select Map Not. Output pulses low ty pically for 240 ns when map is accessed. RDN 2 O Read Not. Output pulses low for typical times of 90, 150, and 210 ns, depending on wait states. WRN 3 O Write Not. ...

  • Garmin GNS 430 - page 160

    Page B-10 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 B.3.8 J17 Table B-10. J17 Descriptions Pin Name Pin # I/O Description FAN_HI 1 O Approx. 5 V. FAN_LO 2 O Used to switch fan off and on. B.3.9 P13 Table B-11. P13 Descriptions Pin Name Pin # I/O Description 12V 1 O 12 V dc output. CCFT_TA_NOT 2 O Cold Cathode Transmit A Not logic level ...

  • Garmin GNS 430 - page 161

    400 SERIES MAINTENANCE MANUAL Page B-11 P/N 190-00140-05 Rev. C B.4 COM BOARD CONNECTORS B.4.1 J2 Table B-12. J2 Descriptions Pin # Name I/O 1 RESERVED 2 COM IF AGC TEST O 3 SQUELCH / COMPRESSOR TEST I 4 COM MIC KEY I 5 INTERCOM MIC HI I 6 COM MIC AUDIO HI I 7 500 : COM AUDIO HI O 8 RESERVED I 9 RESERVED I 10 RESERVED I 11 AIRCRAFT POWER I 12 AIRCR ...

  • Garmin GNS 430 - page 162

    Page B-12 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 B.4.2 J26 Table B-13. J26 Descriptions Pin # Pin Name I/O Description 1 +12 VDC I 2 -12 VDC I 3 + 5 VDC I 4 SERIAL_IN I Asynchronous serial input. 5 SERIAL_OUT O Asy nchronous serial output. 6 DC_VOL_CONT I High impedance A/D input. In the unit it is fed by the center tap of a 20K pot ...

  • Garmin GNS 430 - page 163

    400 SERIES MAINTENANCE MANUAL Page B-13 P/N 190-00140-05 Rev. C Table B-14. J6 Descriptions (continued) 16 500 : VOR/ILS AUDIO HI O 17 500 : VOR/ILS AUDIO LO (GND) O 18 SERIAL DME CLOCK O 19 SERIAL DME DATA O 20 SER DME - CHAN REQ /PAR DME - 4MHZ I/O 21 SER DME - RNAV MODE /PAR DME - 2MHZ I/O 22 VOR/ILS DME COMMON I 23 VOR/ILS 429 OUTB O 24 VOR/ILS ...

  • Garmin GNS 430 - page 164

    Page B-14 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 B.5.2 J10 Table B-15. J10 Descriptions Pin # Pin Name I/O Description 1 +12VDC I 2 +5VDC I 3 GND I 4 -12VDC I 5 VLOC SERIAL IN I Serial input from the Main CPU board to the NAV Board. 6 KEY - This pin is not used. 7 G/S SERIAL IN I Serial input from the Main CPU board to the G/S board. ...

  • Garmin GNS 430 - page 165

    400 SERIES MAINTENANCE MANUAL Page B-15 P/N 190-00140-05 Rev. C B.6 GLIDESLOPE BOARD CONNECTORS B.6.1 J25 Table B-17. J25 Descriptions Pin # Pin Name I/O DESCRIPTION 1 +12VDC I 2 +5VDC I 3 GND I Ground. 4 -12VDC I 5 G/S IF AGC O The IF AGC output. 10K output impedance. 6 G/S Composite O Not Used. 7 G/S SERIAL_IN I Serial input from Main Board. 8 G/ ...

  • Garmin GNS 430 - page 166

    Page B-16 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 B.8 INVERTER BOARD CONNECTORS B.8.1 J13 Table B-18. J13 Description Pin # Pin Name I/O Description 1 12V I 11 to 14 V dc. 2 CCFT_TA_NOT I Cold Cathode Transmit A Not input. Occurs at 58.5 kHz and is active low. Inverter is capacitor coupled. 3 CCFT_TB_NOT I Cold Cathode Transmit B Not ...

  • Garmin GNS 430 - page 167

    400 SERIES MAINTENANCE MANUAL Page B-17 P/N 190-00140-05 Rev. C B.8.3 J27 Table B-20. J27 Description Pin # Pin Name I/O DESCRIPTION 1 HEATER VIN O Heater high. The heater typical resistance is 16 ohms. 2 HEATER GND I Heater low. B.9 GPS MODULE CONNECTORS B.9.1 J101 Table B-21. J101 Descriptions Pin # Pin Name I/O DESCRIPTION TRAP 1 I 0 to 12 V dc ...

  • Garmin GNS 430 - page 168

    Page B-18 400 SERIES MAINTENANCE MANUAL Rev. C P/N 190-00140-05 B.11 DISPLAY MODULE CONNECTORS B.11.1 J22 See LCD Flex description (J12). B.12 DATA BASE CARD CONNECTORS J20 and J21 are the Data Base Card Connectors. B.13 MAP BOARD CONNECTORS B.13.1 P16 Table B-22. P16 Descriptions Pin Name Pin # I/O DESCRIPTION CS_MAPN 1 O Chip Select Map Not. Outp ...

Manufacturer Garmin Category GPS Receiver

Documents that we receive from a manufacturer of a Garmin GNS 430 can be divided into several groups. They are, among others:
- Garmin technical drawings
- GNS 430 manuals
- Garmin product data sheets
- information booklets
- or energy labels Garmin GNS 430
All of them are important, but the most important information from the point of view of use of the device are in the user manual Garmin GNS 430.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Garmin GNS 430, service manual, brief instructions and user manuals Garmin GNS 430. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Garmin GNS 430.

Similar manuals

A complete manual for the device Garmin GNS 430, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Garmin GNS 430 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Garmin GNS 430.

A complete Garmin manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Garmin GNS 430 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Garmin GNS 430, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Garmin GNS 430, that we can find in the current document
3. Tips how to use the basic functions of the device Garmin GNS 430 - which should help us in our first steps of using Garmin GNS 430
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Garmin GNS 430
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Garmin GNS 430 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Garmin GNS 430?

Use the form below

If you did not solve your problem by using a manual Garmin GNS 430, ask a question using the form below. If a user had a similar problem with Garmin GNS 430 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (2)

gianfranco

Avrei bisogno, se fosse possibile, dei manuali in italiano del Garmin 430 e del Garmin G5. possibilmente di un video esplicativo, grazie Gianfranco

Francesco Dal Mas

Salve avrei bisogno del manuale per la programmazione per una navigazione del Garmin 430 e se fosse possibile anche un video italiano grazie saluti Franco