English dropdown-ico

Manual Icom IC-F3061T/S

36 pages 0.67 mb
Download

Go to site of 36

Summary
  • Icom IC-F3061T/S - page 1

    INSTRUCTION MANUAL This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. iF3063T/S iF3061T/S VHF TRANSCEIVER iF4063T/S iF4061T/S UHF TRANSCEIVER ...

  • Icom IC-F3061T/S - page 2

    i WORD DEFINITION R W ARNING Personal injury , fire hazard or electric shock may occur . CAUTION Equipment damage may occur . NOTE If disregarded, inconvenience only . No risk of personal injury , fire or electric shock. READ ALL INSTRUCTIONS carefully and com- pletely before using the transceiver . SA VE THIS INSTRUCTION MANUAL — This instruct ...

  • Icom IC-F3061T/S - page 3

    ii IMPORT ANT ........................................................................ i EXPLICIT DEFINITIONS ..................................................... i T ABLE OF CONTENTS ...................................................... ii PRECAUTIONS ................................................................. iii 1 ACCESSORIES ........... ...

  • Icom IC-F3061T/S - page 4

    iii PRECAUTIONS R CAUTION! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body , especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 2 to 4 in. (5 to 10 cm) away from the lips and the transceiver is vertical. R CAUTION! NEVER operate the transceiv ...

  • Icom IC-F3061T/S - page 5

    1 1 ACCESSORIES ■ Supplied accessories The following accessories are supplied: Qty . q Flexible antenna …………………………………………… 1 w Battery pack ……………………………………………… 1 e Belt clip …………………………………………………… 1 r Connector cover (with screw) ………… ...

  • Icom IC-F3061T/S - page 6

    2 1 ACCESSORIES ï Battery pack To attach the battery pack: Slide the battery pack in the direction of the arrow ( q ), then lock it with the battery release button. • Slide the battery pack until the battery release button makes a ‘click’ sound. To release the battery pack: Slide the battery release button in the direction of the arrow ( w ) ...

  • Icom IC-F3061T/S - page 7

    3 1 ACCESSORIES 1 ï Connector cover Attach the connector cover when the optional speaker-micro- phone or head-set is not used. To attach the connector cover: q Insert the connector cover into the multi-connector . w T ighten the screw . CAUTION! Attach the connector cover when the optional speaker- microphone or head-set is not used. Otherwise the ...

  • Icom IC-F3061T/S - page 8

    4 2 P ANEL DESCRIPTION ■ Front panel q ROT ARY SELECT OR Rotate to select the pre-programmed memory channels or the operating zone. (Depending on the pre-setting) w ANTENNA CONNECTOR Connects the supplied antenna. e DEALER-PROGRAMMABLE KEY [Emer] Desired functions can be programmed by your dealer . (( ☞ p. 7) ) r DEALER-PROGRAMMABLE KEY [Side1] ...

  • Icom IC-F3061T/S - page 9

    5 2 PA NEL DESCRIPTION 2 !0 MUL TI-CONNECTOR Connect an optional speaker-microphone. !1 BUSY/TRANSMIT INDICA TOR ➥ Lights green while receiving a signal, or when the squelch is open. ➥ Lights red while transmitting. !2 VOLUME CONTROL [VOL] Rotate to turn the power ON/OFF and adjusts the audio level. Connector cover NOTE: Attach the connector co ...

  • Icom IC-F3061T/S - page 10

    6 2 P ANEL DESCRIPTION ■ Function display q SIGNAL STRENGTH INDICA TOR Indicates relative signal strength level. w LOW POWER INDICA TOR Appears when low output power is selected. e AUDIBLE INDICA TOR ➥ Appears when the channel is in the ‘audible’ (un-mute) condition. ➥ Appears when the specified 2-tone is received. r COMP ANDER INDICA TO ...

  • Icom IC-F3061T/S - page 11

    7 2 PA NEL DESCRIPTION 2 ■ Programmable function keys The following functions can be assigned to [Emer] , [Side1], [Side2] , [Side3] , [P0] , [P1] , [P2] and [P3] programmable function keys. Consult your Icom dealer or system operator for details con- cerning your transceivers programming. If the programmable function names are bracketed in the f ...

  • Icom IC-F3061T/S - page 12

    8 2 P ANEL DESCRIPTION SCAN ADD/DEL (T AG) KEY “ S S C C A A D D ” Push to add or delete the selected channel to/from the scan group. PRIO A/B KEYS “ P P R R A A ” “ P P R R A A R R ” “ P P R R B B ” “ P P R R B B R R ” ➥ Push to select Priority A or Priority B channel. ➥ Push and hold [Prio A (Rewrite)] to rewrite the Prio ...

  • Icom IC-F3061T/S - page 13

    9 2 PA NEL DESCRIPTION 2 CALL KEYS “ C C A A L L L L ” “ C C A A L L A A ” “ C C A A L L B B ” Push to transmit a 2-tone. • Call transmission is necessary before you call another station depending on your signaling system. • [Call A] and/or [Call B] may be available when your system employs selective ‘Individual/Group’ calls. As ...

  • Icom IC-F3061T/S - page 14

    ■ Tu rning power ON Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. (( ☞ p. 20) ) q Rotate [VOL] to turn the power ON. w If the transceiver is programmed for a start up password, input the digit codes as directed by your dealer . • 10-keypad can be used for password in ...

  • Icom IC-F3061T/S - page 15

    11 3 BASIC OPERA TION 3 ■ Channel selection Several types of channel selections are available. Methods may differ according to your system set up. NON-ZONE TYPE: Push [CH Up] or [CH Down], or rotate [ ROT ARY SELEC- TOR ]* to select the desired operating channel, in sequence; or , push one of [MR-CH 1] to [MR-CH 4] keys to select a channel direct ...

  • Icom IC-F3061T/S - page 16

    ■ Receiving a call D Group call q P ush [CH Up] or [CH Down], or rotate [ ROT ARY SELEC- TOR ]* to select the L TR system channel or talk group . w When a call is received; • ‘BUSY’ indicator lights green. e Push and hold [PTT], then speak into the microphone at a normal voice level. r Release [PTT] to return to receive. D Selective call (D ...

  • Icom IC-F3061T/S - page 17

    13 4 L TR OPERA TION 4 • Make a phone call q S elect the phone channel of L TR system channel . • “” appears. w Push [PHONE] (or push [PTT]). • “” blinks. e Push [DTMF Autodial] (or while pushing and holding [PTT] enter the desired telephone number using 10 key pad) to make a phone call. r After conversation is finished, push [PHONE] ...

  • Icom IC-F3061T/S - page 18

    14 5 CONVENTIONAL OPERA TION ■ Receiving and transmitting NOTE: T ransmitting without an antenna may damage the transceiver . See ( ( ☞ p. 1) ) for accessory attachments. Receiving: q Rotate [VOL] to turn the power ON. w Push [CH Up] or [CH Down], or rotate [ ROT ARY SELEC- TOR ]* to select the conventional system channel, in sequence. * Depend ...

  • Icom IC-F3061T/S - page 19

    15 5 CONVENTIONAL OPERA TION 5 D TX code channel selection If the transceiver has [TX Code CH Select] assigned to it, the indication can be toggled between the operating channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) is displayed, [CH Up] or [CH Down] selects the TX code channel. USING [TX C ...

  • Icom IC-F3061T/S - page 20

    16 5 CONVENTIONAL OPERA TION ■ User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can “cus- tomize” the transceiver operation to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [P1] and [P2], rotate [VOL] to turn the power ON. T ...

  • Icom IC-F3061T/S - page 21

    17 5 CONVENTIONAL OPERA TION 5 ■ Stun function When the specified ID, set as a killer ID, is received, the stun function is activated. When the killer ID is received, the transceiver switches to the password required condition. Entering of the password via the keypad is necessary to operate the transceiver again in this case. ■ Priority A chan ...

  • Icom IC-F3061T/S - page 22

    18 6 BA TTER Y CHARGING ■ Caution • R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom charger . Only Icom battery packs are tested and approved for use and charge with Icom radios or Icom charger . Using third-party or counterfeit bat- tery packs or charger may cause smoke, fire, or cause the battery to burst. ...

  • Icom IC-F3061T/S - page 23

    19 6 BA TTERY CHARGING 6 • W ARNING! Immediately stop using the battery if it emits an abnormal odor , heats up, or is discolored or deformed. If any of these conditions occur , contact your Icom dealer or dis- tributor . • W ARNING! Immediately wash, using clean water , any part of the body that comes into contact with fluid from inside the b ...

  • Icom IC-F3061T/S - page 24

    20 6 BA TTERY CHARGING ■ Optional battery chargers ï Rapid charging with the BC-160 The optional BC-160 provides rapid charging of optional Li- Ion battery packs. • An AC adapter (may be supplied with BC-160 depending on version) or the DC power cable (OPC-515L/CP-17L) is addi- tionally required. ï AD-106 installation q Install the AD-106 des ...

  • Icom IC-F3061T/S - page 25

    21 6 BA TTERY CHARGING 6 ï Rapid charging with the BC-1 19N+AD-106 The optional BC-1 19N provides rapid charging of battery packs. The following items are additionally required. • AD-106 charger adapter • An AC adapter (may be supplied with BC-1 19N depending on version) or the DC power cable (OPC-515L/CP-17L). ï Rapid charging with the BC-12 ...

  • Icom IC-F3061T/S - page 26

    22 6 BA TTERY CHARGING IMPORT ANT!: Battery charging caution Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter . (This illustration is described with the BC-160.) Guide rail Lobs ...

  • Icom IC-F3061T/S - page 27

    23 7 BA TTER Y CASE 7 6 ■ Optional battery case (BP-240) When using the optional battery case attached to the trans- ceiver , install 6 × AAA (LR03) size alkaline batteries as illus- trated at right. q Unhook the battery cover release hook ( q ), and open the cover in the direction of the arrow ( w ). (Fig.1) w Then, install 6 × AAA (LR03) size ...

  • Icom IC-F3061T/S - page 28

    24 8 SWIVEL BEL T CLIP ■ MB-93 contents Qty . q Belt clip ……………………………………………………… 1 w Base clip …………………………………………………… 1 ■ Attaching q Release the battery pack if it is attached. ( ( ☞ p. 2) ) w Slide the base clip in the direction of the arrow until the base clip i ...

  • Icom IC-F3061T/S - page 29

    25 8 SWIVEL BEL T CLIP 8 ■ Detaching q T urn the transceiver upside down in the direction of the arrow and pull out from the belt clip. w Release the battery pack if it is attached. ( ( ☞ p. 2) ) e Pinch the clip ( q ), and slide the base clip in the direction of the arrow ( w ). CAUTION! HOLD THE TRANSCEIVER TIGHTL Y , WHEN HANGING OR DET ACHI ...

  • Icom IC-F3061T/S - page 30

    26 9 OPTIONS D BA TTER Y P ACK D CHARGERS • BC-1 19N DESKTOP CHARGER + AD-106 CHARGER ADAPTER + BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is sup- plied with the charger depending on versions. Charging time: approx. 2 hours when BP-231 is attached. • BC-121N MUL TI - CHARGER + AD-106 CHARGER ADAPTER (6 pcs.) + BC-157 A ...

  • Icom IC-F3061T/S - page 31

    27 9 OPTIONS 9 D OTHER OPTIONS • SP-13 EARPHONE Provides clear receive audio in noisy environment. • HM-131SC/HM-159SC SPEAKER - MICROPHONE Combination speaker-microphone that provides convenient operation while hanging the transceiver from your belt. • HS-94/HS-95/HS-97 HEADSET + VS-1SC VOX / PTT CASE HS-94: Ear-hook type HS-95: Neck-arm typ ...

  • Icom IC-F3061T/S - page 32

    28 9 OPTIONS VOX gain and delay adjustment q Attach the connector of the VS-1SC into the multi-connec- tor on the transceiver and tighten the screw . • T oggle the VOX/PTT select switch to [VOX]. w Enter user set mode. ( ( ☞ p. 16) ) e Push [P0] several times to select the “VOX Gain” or “VOX Delay” items. Then, push [Side2] or [Side3] t ...

  • Icom IC-F3061T/S - page 33

    29 10 SAFETY TRAINING INFORMA TION 10 9 Y our Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT inten ...

  • Icom IC-F3061T/S - page 34

    30 10 SAFETY TRAINING INFORMA TION Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitiv ...

  • Icom IC-F3061T/S - page 35

    31 MEMO 10 ...

  • Icom IC-F3061T/S - page 36

    1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6488D-1EX- q Printed in Japan © 2006 Icom Inc. ...

Manufacturer Icom Category Marine Radio

Documents that we receive from a manufacturer of a Icom IC-F3061T/S can be divided into several groups. They are, among others:
- Icom technical drawings
- IC-F3061T/S manuals
- Icom product data sheets
- information booklets
- or energy labels Icom IC-F3061T/S
All of them are important, but the most important information from the point of view of use of the device are in the user manual Icom IC-F3061T/S.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Icom IC-F3061T/S, service manual, brief instructions and user manuals Icom IC-F3061T/S. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Icom IC-F3061T/S.

Similar manuals

A complete manual for the device Icom IC-F3061T/S, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Icom IC-F3061T/S by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Icom IC-F3061T/S.

A complete Icom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Icom IC-F3061T/S - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Icom IC-F3061T/S, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Icom IC-F3061T/S, that we can find in the current document
3. Tips how to use the basic functions of the device Icom IC-F3061T/S - which should help us in our first steps of using Icom IC-F3061T/S
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Icom IC-F3061T/S
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Icom IC-F3061T/S in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Icom IC-F3061T/S?

Use the form below

If you did not solve your problem by using a manual Icom IC-F3061T/S, ask a question using the form below. If a user had a similar problem with Icom IC-F3061T/S it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)