English dropdown-ico

Manual Wilton 7015

32 pages 2.88 mb
Download

Go to site of 32

Summary
  • Wilton 7015 - page 1

    Owner's Manual 8-in x 13-in Horizontal Cut-Off Bandsaw Model: 7015 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No. M-7015 Ph.: 800-274-6848 Revision B 02/07 www.wmhtoolgroup.com Copyright © WMH Tool Group This Manual is Boo kmarked This Manual is Bookmarked ...

  • Wilton 7015 - page 2

    2 Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughou t the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtainin ...

  • Wilton 7015 - page 3

    3 Table of Contents Warranty and Service........................................................................................................... ......................... 2 Table of Contents .............................................................................................................. ............................ 3 Warnings ..... ...

  • Wilton 7015 - page 4

    4 Warnings 1. Read and understand the entire o wner's manual before attempting assembly o r operation. 2. Rea d and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 3. Replace the warning labels if they become obscu red or removed. 4. The bandsa w is desig ...

  • Wilton 7015 - page 5

    5 21. Keep visitors a safe distance from the work area. Keep children away. 22. Make your workshop child proof with padlocks , mas ter switches or by removing starter keys. 23. Give your work undivided attention. Looking a round, carrying on a conversation and “horse-play” are careless acts that can result in seriou s injury. 24. Maintain a bal ...

  • Wilton 7015 - page 6

    6 Familiarize yourself with the follo w ing safety notices used in this manual: This means that if precautions are not heeded, it may result in minor injury and/or possible machine damage. This means that if precautions are not heeded, it may result in serious injury or possibly even death. Introduction The Wilton Model 7015 Horizontal Cut-off Band ...

  • Wilton 7015 - page 7

    7 Machine Features Figures 1 and 2 depict the main features of the Model 7015 Horizontal Cut-Off Bandsaw. The machine consists of a machin e base onto which is installed a saw hea d. Figure 1 Machine Base The machine base consists of a coolant collection pan mounted on two panels that form the legs of the machine. A shelf is provide d under the col ...

  • Wilton 7015 - page 8

    8 The mechanism also has adjustment screws that enable the saw blade to “track” evenly o n the blade wheels. The adjustment screws change the angle of the dri ven blade wheel shaft so the wheels are aligne d. Tracking adjustments are generally made after the saw blade is changed but may be required pe riodically due to wear over time. An electr ...

  • Wilton 7015 - page 9

    9 2. Place a warning placard or tag on the service panel to prevent acciden tal electrical shock. 3. When installing the motor power cord into a receptacle, make sure the plug is compatible with the receptacle. 4. When using hard-wired connections, connect the wires as shown in the Wiring Data section. 5. Install the fuses or reset the brea kers. C ...

  • Wilton 7015 - page 10

    10 Blade Selection The cut-off saw is delivered with a saw blade that is adequate for a variety of cut-off jobs on a variety of common materials. A 10-tooth, general-purpose blade is provided a s standard equipment with the machine. An optional 8-tooth blade and an optional 14-tooth blade are available from Wilton. (Refer to the Parts section for s ...

  • Wilton 7015 - page 11

    11 Evaluating Cutting Efficiency Is the blade cutting efficiently? The best way to determine this is to obse rve the chips formed by the cutting blade. If the chip formation is powdery, then the feed is much too light, or the blade is dull. If the chips formed are cu rled, but colored – blue or straw colored from heat generated during the cut – ...

  • Wilton 7015 - page 12

    12 Starting the Saw Important : The efficient operation of the cut-off saw is dependent upon the con dition of the saw blade. If the performance of the saw begins to deteriorate, the first item that you should check is the blade. If a new blade does not restore the machine’ s cutting accuracy and quality, refer to the troubleshooting guide (or th ...

  • Wilton 7015 - page 13

    13 Coolant Flow and Nozzle Position The coolant pump must be submerged before operating to prevent damage to the pump. Adjust the coolant flow shut-off valve at the top of the saw head weldment. The flow should be no more than the saw blade can dra w into the workpiece by the movement of the blade. The coolant flow can be stopped in two ways:  b ...

  • Wilton 7015 - page 14

    Adjustments Blade Tracking Adjustment Refer to Figures 13 and 14. Blade tracking has bee n set and tested at the factory. Adjustment is rarely required when the blade is used properly or if the blade is correctly welded. If adjustment is needed: 1. Using the blade tension handwheel (D), make sure the blade is properly tensione d. Note: Blade tensio ...

  • Wilton 7015 - page 15

    15 Repeat the insertion of t he paper between the wheel shoulder and the blade until the paper is cut in two pieces. Note: You may have to repeat the check with the paper several times before the blade and the shoulder cut the pape r into two pieces. Do not hurry the adjustment. Patience and ac curacy here will pay off with better, more accurate, q ...

  • Wilton 7015 - page 16

    16 Blade Guide Bearing Adjustment Referring to Figure 16: Guide bearings and guid e inserts are located on either side of the saw blade and provide stability for the blade when the saw is in operation. These bearings rotate on an eccentric shaft so the distance from the blade can be adjusted for optimal performance. Blade guides provide blade suppo ...

  • Wilton 7015 - page 17

    17 Verifying Adjustment Accuracy Refer also to Figure 18. Test cuts can be used to determine whether or not you have adjusted the blade a ccurately. Use 2 inch round bar stock to perf orm these test cuts, as follows: 1. With the bar stock securely clamped in the vise, make a cut through the bar stock. 2. Mark the top of the bar stock. 3. Move the b ...

  • Wilton 7015 - page 18

    18 Maintenance Figure 21 Changing Blades Use leather gloves when changing the saw blade to protect y our hands from cuts and scr atches. Use protective eye wear that meets ANSI Specification Z87.1 Disconnect the cut-off sa w from its electrical power source. Referring to Figure 21: 1. Raise the saw head (A). Set the feed rate control knob (B) to ze ...

  • Wilton 7015 - page 19

    Changing the Drive Belt Referring to Figures 22 and 23: Disconnect the cut-off saw from its electrical power source. 1. Set the arm at the full horizontal position. 2. Open the drive belt cover to expose t he V-belt and pulleys . 3. Loosen the belt tension adjust knob located in the rear under the motor (see Figure 23 for knob direction). Lift the ...

  • Wilton 7015 - page 20

    Cleaning 1. Clean off any preservative on machine surfac es. After cleaning: 2. Coat machined surfaces of the cutoff saw with a medium consistency ma chine oil. Reapply the oil coating at least every six months. 3. Clean up accumulated saw cuttings after use. Make sure the lead screw and rapid nut are kept free from saw cuttings and other material ...

  • Wilton 7015 - page 21

    21 Troubleshooting Fault Probable Cause Suggested remedy Excessive blade breakage 1. Material loose in vise. 2. Incorrect spe ed or feed. 3. Teeth too coarse for materi al. 4. Incorrect blade tensio n. 5. Saw blade is in conta ct with workpiece before the saw is started. 6. Blade rubs on the whe el flange. 7. Misaligned guides. 8. Cracking at weld. ...

  • Wilton 7015 - page 22

    22 Troubleshooting Fault Probable Cause Suggested remedy Bad cuts (rough) 1. Blade speed t oo high for feed pressure. 2. Blade is too coarse. 1. Reduce blade spe ed and feed pressure. 2. Replace with finer blad e. Blade is twisting 1. Blade is binding in the cut. 2. Blade tension too high 1. Decrease feed pressure. 2. Decrease ten sion on Blade Unu ...

  • Wilton 7015 - page 23

    23 Parts Saw Stand and Bed Index No. Part No. Description Size Qty 1-1 ............ TS-1499141 ............. Hex Cap Screw .................................................... M12x80 .................. ..... 4 1-2 ............ TS-1540081 ............. Hex Nut ................................................................ M12 ............... ..... ...

  • Wilton 7015 - page 24

    24 Saw Stand and Bed Index No. Part No. Description Size Qty 31 ............. TS-1490031 ............. Hex Cap Screw .................................................... M8x20 ................... ...... 2 32 ............. 7015-32 .................... Rear Pivot Bracket ............................................... .................... ........... ...

  • Wilton 7015 - page 25

    25 Saw Stand and Bed – Parts Breakdow n ...

  • Wilton 7015 - page 26

    26 Saw Head Index No. Part No. Description Size Qty 200 ........... 7015-200 .................. Blade Guard ......................................................... ................... ................. 2 201 ........... 7015-201 .................. Direction Label ..................................................... ................... .......... ...

  • Wilton 7015 - page 27

    27 Saw Head Index No. Part No. Description Size Qty 314-1 ........ 7015-314-1 ............... Connector............................................................. PT1/2" ......................... 1 314-2 ........ 7015-314-2 ............... Hose ..................................................................... 18x24-190mm ..... ........ 1 ...

  • Wilton 7015 - page 28

    28 Saw Head Index No. Part No. Description Size Qty 354-8 ........ TS-1503071 ............. Socket Head Cap Screw ...................................... M6x30 ......................... 2 354-9 ........ 7015-354-9 ............... Ho se ..................................................................... ID1/4"x2.2tx143c m ..... 1 354-10 ...... ...

  • Wilton 7015 - page 29

    29 Saw Head – Parts Breakdow n ...

  • Wilton 7015 - page 30

    30 Electric Assembly – Parts and Breakdown Index No. Part No. Description Size Qty 5-1 ........... 7015-5-1 ................... Fuse Base ............................................................ 5x30mm .......... ............ 2 5-3 ............ 7015-5-3 ................... Fuse ................................................................. ...

  • Wilton 7015 - page 31

    31 Wiring Diagram ...

  • Wilton 7015 - page 32

    32 Ordering Replacement Parts To order parts or rea ch our service department, call 1-80 0-274-6848 between 7:30am and 5:30pm (CST ), Monday through Friday. Having the Model Numbe r and Serial Number of your machine available when you call will allow us to serve you quickly and accuratel y. WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Ph ...

Manufacturer Wilton Category Saw

Documents that we receive from a manufacturer of a Wilton 7015 can be divided into several groups. They are, among others:
- Wilton technical drawings
- 7015 manuals
- Wilton product data sheets
- information booklets
- or energy labels Wilton 7015
All of them are important, but the most important information from the point of view of use of the device are in the user manual Wilton 7015.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Wilton 7015, service manual, brief instructions and user manuals Wilton 7015. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Wilton 7015.

Similar manuals

A complete manual for the device Wilton 7015, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Wilton 7015 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Wilton 7015.

A complete Wilton manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Wilton 7015 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Wilton 7015, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Wilton 7015, that we can find in the current document
3. Tips how to use the basic functions of the device Wilton 7015 - which should help us in our first steps of using Wilton 7015
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Wilton 7015
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Wilton 7015 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Wilton 7015?

Use the form below

If you did not solve your problem by using a manual Wilton 7015, ask a question using the form below. If a user had a similar problem with Wilton 7015 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)