English dropdown-ico

Manual Kenwood DPX-MP4070

40 pages 3.23 mb
Download

Go to site of 40

Summary
  • Kenwood DPX-MP4070 - page 1

    DOUBLE DIN SIZED CD/CASSETTE RECEIVER DPX-MP4070 INSTRUCTION MANUAL © B64-2861-00/00 (K) (TKR) 1.DPX-MP4070_K_US.indd 04.3.12, 5:05 PM 1 ...

  • Kenwood DPX-MP4070 - page 2

    2 | English Con tents W arning 3 Safety precautions 4 W ARNING CAUTION NOTE Notes 6 About Cassette tape 6 About CDs 7 Notes on playing MP3/WMA 8 General features 10 Pow er Selecting the Source Volume Attenuator Audio Control Subwoofer Output TEL Mute SRS WOW Selec t SRS WOW Control Equalizer Control Adjustment of Equalizer type at EASY Adjustment o ...

  • Kenwood DPX-MP4070 - page 3

    English | 3 2 W arning 2 CAUTION Use of controls or adjustments or per formance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with F ederal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. KENWOOD CORPORA TION 2967-3, ISHIKAW A- ...

  • Kenwood DPX-MP4070 - page 4

    4 | English Safety precautions 2 CA UTION T o prevent damage to the machine, take the following precautions: • Make sure to ground the unit to a negative 12V DC power supply . • Do not open the top or bottom covers of the unit. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with ...

  • Kenwood DPX-MP4070 - page 5

    English | 5 About CD play ers/disc changers connected to this unit KENWOOD disc changers/ CD players released in 1998 or later can be connected to this unit. Refer to the catalog or consult your Kenwood dealer for connec table models of disc changers/ CD players. Note that any KENWOOD disc changers/ CD players released in 1997 or ear lier and disc ...

  • Kenwood DPX-MP4070 - page 6

    6 | English Cleaning the tape head When there’ s noise or the sound qualit y is bad during tape play the tape head maybe dirt y , clean the tape head. About Cassette tape • If the tape is slack tighten it. • If the cassette tape label is peeling off glue it on again. • Don ’t use deformed cassette tape. • Don ’t place cassette tape on ...

  • Kenwood DPX-MP4070 - page 7

    English | 7 Handling CDs • Don ’t touch the recording sur face of the CD. • CD-R and CD-R W are easier to damage than a normal music CD. Use a CD-R or a CD -RW after reading the caution items on the pack age etc. • Don ’t stick tape etc. on the CD. Also, don ’t use a CD with tape stuck on it. When using a new CD If the CD center hole or ...

  • Kenwood DPX-MP4070 - page 8

    8 | English Notes on playing MP3/WMA Note, however , that the MP3/WMA recording media and formats acceptable are limited. When writing MP3/WMA, pay attention to the following restrictions. Acc eptable media The MP3/WMA recording media acceptable to this unit are CD-ROM, CD -R, and CD-R W . When using CD-R W , do full format not quick format to prev ...

  • Kenwood DPX-MP4070 - page 9

    English | 9 MP3/WMA playing order When selec ted for play , Folder Search, File Search, or for Folder Selec t, files and folders are accessed in the order in which they were wr itten by the CD writer . Because of this, the order in which they are expected to be played may not match the order in which they are actually played. You may be able to set ...

  • Kenwood DPX-MP4070 - page 10

    10 | English               Po wer T urning ON the P ower Press the [SRC ] button. T urning OFF the P ower Press the [SRC ] button for at least 1 second. Selec ting the Sourc e Press the [SRC ] button. Source r ...

  • Kenwood DPX-MP4070 - page 11

    English | 11 Subw oofer O utput T urning the Subwoof er output ON or OFF . Press the [AM–] button for at least 1 second. Each time the button is pressed Subwoofer output switches ON or OFF . When it ’ s ON, "SubW On" is displayed . • Y ou can control this function when 'Switching preout' (page 25) is set to "SWPRE SW& ...

  • Kenwood DPX-MP4070 - page 12

    12 | English General features Heavy Heavy "Heavy" "Heavy" Soft "Soft" Sharp Sharp "Sharp" "Sharp" Light Light "Light" "Light" Natural "Natural" • "User" display : The values set on the ' Adjustment of Equalizer type at PRO' (page 13). • A selecte ...

  • Kenwood DPX-MP4070 - page 13

    English | 13 Adjustment of Equalizer type at PRO Adjusting the effect of an Equalizer type selected in 'Equalizer Control' when 'Equalizer mode' is "PRO" . 1 Refer to 'Equalizer C ontrol' (page 12) to select the Equalizer type. 2 Select the item for adjustment Press the [FM+] or [AM–] button. Each time the ...

  • Kenwood DPX-MP4070 - page 14

    14 | English General features Switching Display Switching the information display ed. Press the [DISP] button. Each time the button is pressed the display switches as shown below . In T uner source Information Display Display Display Fr equency Fr equency Station name or Frequency Station name or Frequency "SNPS" Character Clock In CD &am ...

  • Kenwood DPX-MP4070 - page 15

    English | 15 Adjusting Clock 1 Select the clock display Press the [DISP] button. 2 Enter clock adjustment mode Press the [DISP] button for at least 1 second. The ‡ indicator blinks. 3 Adjust the hours Press the [FM+] or [AM–] button. Adjust the minutes Press the [ 4 ] or [ ¢ ] button. 4 Exit clock adjustment mode Press the [DISP] button. User ...

  • Kenwood DPX-MP4070 - page 16

    16 | English General features Station/Disc Naming (SNPS/DNPS) Attaching a title to a Station or CD. 1 Receive/pla y the station/disc you want to attach a title to • Refer to the 'Switching Display' (page 14) and selec t either "DNPS" or "SNPS" . No name can be attached to the source if "DNPS" or "SNPS& ...

  • Kenwood DPX-MP4070 - page 17

    English | 17 T uner f eatures T uning Selecting the station. 1 Select tuner source Press the [SRC ] button. Select the " TUNER" display . 2 Select the band Press the [FM+] or [AM–] button. Each time the [FM+] button is pressed it switches between the FM1, FM2, and FM3 bands. 3 T une up or down band Press the [ 4 ] or [ ¢ ] button. • ...

  • Kenwood DPX-MP4070 - page 18

    18 | English Station Preset Memor y Putting the station in the memory. 1 Select the band Press the [FM+] or [AM–] button. 2 Select the frequency to put in the memor y Press the [ 4 ] or [ ¢ ] button. 3 Put the frequenc y in the memory Press the desired [1] — [6] button for at least 2 seconds. The preset number display blinks 1 time. On each ba ...

  • Kenwood DPX-MP4070 - page 19

    English | 19 Cassette play er fea tures Selec ting the T ape type Press the [MTL] button. Each time the button is pressed the T ape type switches as shown below . T ape type T ape type T ape type Display Display Display CrO ₂ (T ype II), FeCr (T ype III), Metal (T ype IV ) (T ype II), FeCr (T ype III), Metal (T ype IV ) "MTL On" Normal ...

  • Kenwood DPX-MP4070 - page 20

    20 | English Cassette play er fea tures DPSS (Direc t Program Search Sy stem) Indicating the songs to skip, and Fast F orwarding or Rewinding. Skipping to a later song Press the [ ¢ ] button. Each time the button is pressed the number of songs sk ipped increases. Skipping to a previous song Press the [ 4 ] button. Each time the button is pressed t ...

  • Kenwood DPX-MP4070 - page 21

    English | 21 CD/ MP3/ WMA/ External disc control featur es              Playing CD & MP3/WMA When a CD is inser ted Press the [SRC ] button. Select the "CD" display . • When a CD is inser ted, the indicator is ON. • ...

  • Kenwood DPX-MP4070 - page 22

    22 | English CD/ MP3/ WMA/ External disc control featur es Playing External Disc Playing discs set in the optional accessory disc player connected to this unit. Press the [SRC ] button. Select the display for the disc player you want. Display examples: Display Display Display Display Disc player Disc player Disc player Disc player "CD CH" ...

  • Kenwood DPX-MP4070 - page 23

    English | 23 In MP3/WMA sourc e Repeat play Repeat play Repeat play Display Display Display File Repeat File Repeat "File REP" Folder Repeat Folder Repeat "Fold.REP" OFF F unction of MP3/WMA Folder Select Quickly selecting the folder you want to listen to. 1 Enter Folder Select mode Press the [F .SEL] button. During S elect mode ...

  • Kenwood DPX-MP4070 - page 24

    24 | English F unction Set Function Set Setting during operation beep sound etc. functions. The Function Set basic operation method is explained here. The refer ence for the F unction items and their setting content is after this operation explanation. 1 Enter Function Set mode Press the [FNC ] button for at least 1 second. "F unction" is ...

  • Kenwood DPX-MP4070 - page 25

    English | 25 In Standby mode Opening Demonstr ation Setting the Demonstration when P ower is turned ON. Display Display Display Setting Setting "Open On" Demonstration is carried out when Power is turned ON. "Open Off " Demonstration is not carried out when Power is turned ON. In Standby mode T ouch Sensor T one Setting the oper ...

  • Kenwood DPX-MP4070 - page 26

    26 | English F unction Set In Standby mode Security C ode Because authorization by the Security Code is required when it ’ s removed from the vehicle, personalizing this unit is by using the Security Code is a help in preventing theft. • When the Security Code function is activated, the code can ’t be changed and the function can’t be relea ...

  • Kenwood DPX-MP4070 - page 27

    English | 27 In Standby mode CD Read Setting When there is a problem on playing a CD with special format, this setting play the CD by for ce. Display Display Display Setting Setting "CD READ1" Play CD and MP3/WMA. Play CD and MP3/WMA. "CD READ2" Play CD by for ce. Play CD by for ce. • Setting "CD READ 2" cannot play ...

  • Kenwood DPX-MP4070 - page 28

    28 | English Basic O pera tions of remote Loading and Replacing the battery Use two " AA "-size batteries. Slide the cover while pressing downwards to remove it as illustrated . Inser t the batteries with the + and – poles aligned properly , following the illustration inside the case. 2 W ARNING • Store unused batteries out of the rea ...

  • Kenwood DPX-MP4070 - page 29

    English | 29 In T uner source [FM]/ [AM] buttons Select the band. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. [ 4 ]/ [ ¢ ] buttons T une up or down band. [0] — [9] buttons Pr ess buttons [1] — [6] to recall preset stations. [DIRECT ] button Enters and cancels the 'Direct Access T uning' (page ...

  • Kenwood DPX-MP4070 - page 30

    30 | English Ac cessories Ac cessories 1 ..........1 2 ..........1 3 (M5×7mm) ..........6 4 (M5×6mm) ..........6 5 ..........1 6 ..........1 7 ..........1 8 ..........1 9 ..........1 0 (M3×6mm) ..........2 ! (M5×10mm) ..........2 @ ..........1 1.DPX-MP4070_K_US.indd 04.3.12, 5:06 PM 30 ...

  • Kenwood DPX-MP4070 - page 31

    English | 31 Installation Procedur e Installation Proc edure 1. T o prevent a shor t circuit, remove the key from the ignition and disconnect the - batter y . 2. Make the proper input and output wire connections f or each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring har ness wires in the following order: ground, b ...

  • Kenwood DPX-MP4070 - page 32

    32 | English Connecting W ires to T erminals   AUX IN P.CONT MUTE ANT. CONT ILLUMI EXT.CONT. FRONT L FRONT R REAR L REAR R M 4 � 8 m m MAX FM/AM antenna input Wiring harness (Accessory 1 ) Ignition wire (Red) Battery wire ( Y ellow) Ground wire (Black) - ( T o car chassis) Ignition key switch Car fuse box (Main fuse) ACC Car fuse box Batter ...

  • Kenwood DPX-MP4070 - page 33

    English | 33 Installation (For T OY OT A, NISSAN Car etc.) When per forming a check of the CD operation prior to installation, place this unit in a horizontal position and per form a loading/eject of the CD. When a ground wire is included in the wir ing kit (which is sold separately), fasten the ground wire with the binding screw located on the rea ...

  • Kenwood DPX-MP4070 - page 34

    34 | English Installation (For HONDA ACURA Car) Installation type 1 1 Use Accessor y 4 to attach the unit which was assembled in Assembly . 2 Install the center panel with the unit in your car • The illustration shows an example of installation using a vehicle bracket. The shape of the bracket varies with the vehicle to be installed. Some bracket ...

  • Kenwood DPX-MP4070 - page 35

    English | 35 Installation type 2 1 Attach Accessor y 9 which was assembled in Assembly . 2 Remove the factory-installed car stereo and install the unit. Accessory 9 is to be fixed either to the center or bottom, depending on the car model. Accessory 3 3 (M5 × 7 mm) (M5 × 7 mm) Accessory 0 (M3 × 6 mm) Accessory 9 Accessory ! (M5 × 10 mm) F actor ...

  • Kenwood DPX-MP4070 - page 36

    36 | English T roubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON.  The fuse has blown.  After check ing for shor t circuits in the wires, replace th ...

  • Kenwood DPX-MP4070 - page 37

    English | 37 T uner source ? Radio reception is poor .  The car antenna is not extended.  Pull the antenna out all the way . Pull the antenna out all the way .  The antenna control wire is not connected.  Connect the wire correctly, referring to the section on 'Connecting Wires to T erminals' . ? The desired frequency can’ t ...

  • Kenwood DPX-MP4070 - page 38

    38 | English T roubleshooting Guide Disc source ? " A UX EXT " is displayed without achieving External disc control mode.  Unsupported disc changer is connected.  Use the disc changer mentioned in the ' About CD players/disc changers connected to this unit' (page 5) of the sec tion on 'Safety precautions' . ? The ...

  • Kenwood DPX-MP4070 - page 39

    English | 39 The messages shown below display your systems condition. EJEC T: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.  Load the disc magazine properly. No CD in the unit.  Inser t the CD. No Disc: No disc has been loaded in the disc magazine.  Load a disc into the disc magazine. Error 04 ...

  • Kenwood DPX-MP4070 - page 40

    40 | English FM tuner sec tion Fr equency range (200 kHz space) : 87.9 MHz – 107.9 MH z Usable sensitivit y (S/N = 30dB) : 9.3dBf (0.8 µV/75 Ω) Quieting Sensitivit y (S/N = 50dB) : 15.2dBf (1.6 µV/75 Ω) Fr equency response (±3.0 dB) : 30 H z – 15 k Hz Signal to Noise ratio (MONO) : 70 d B Selectivity (±400 kH z) : ≥ 80 d B Stereo sepa ...

Manufacturer Kenwood Category Car Stereo System

Documents that we receive from a manufacturer of a Kenwood DPX-MP4070 can be divided into several groups. They are, among others:
- Kenwood technical drawings
- DPX-MP4070 manuals
- Kenwood product data sheets
- information booklets
- or energy labels Kenwood DPX-MP4070
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenwood DPX-MP4070.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenwood DPX-MP4070, service manual, brief instructions and user manuals Kenwood DPX-MP4070. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenwood DPX-MP4070.

Similar manuals

A complete manual for the device Kenwood DPX-MP4070, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenwood DPX-MP4070 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenwood DPX-MP4070.

A complete Kenwood manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenwood DPX-MP4070 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenwood DPX-MP4070, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenwood DPX-MP4070, that we can find in the current document
3. Tips how to use the basic functions of the device Kenwood DPX-MP4070 - which should help us in our first steps of using Kenwood DPX-MP4070
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenwood DPX-MP4070
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenwood DPX-MP4070 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenwood DPX-MP4070?

Use the form below

If you did not solve your problem by using a manual Kenwood DPX-MP4070, ask a question using the form below. If a user had a similar problem with Kenwood DPX-MP4070 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)