-
Renesas H8S/2128 Series - page 1
H8S/2128 Series QFP-64A User System Interface Cable (HS2128ECH61H) for E6000 Emulator User’s Manual HS2128ECH61HE(C) ...
-
Renesas H8S/2128 Series - page 2
Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property ...
-
Renesas H8S/2128 Series - page 3
i Preface Thank you for purchasing this user system interface cable (HS2128ECH61H) for the Renesas’s original mi crocomputer H8S/2128 series. The HS2128ECH61H is a user system interface cable that connects an H8S/2148, H8S/2138, H8S/2128 series E6000 emul ator (HS2148EPI61H; hereinafter referred to as the emulator) t o the IC socket for a QFP-64A ...
-
Renesas H8S/2128 Series - page 4
ii Contents Section 1 Configuration .................................................................................................... 1 Section 2 Connection Procedures ................................................................................... 4 2.1 Connecting User System Interf ace Cable to Em ulat or Station ........................... ...
-
Renesas H8S/2128 Series - page 5
1 Section 1 Configuration CAUTION Use an IC149-064-008-B5 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-64A package IC socket on the user system. Figure 1 shows the configuration of the HS2128E CH61H user system interface cable for the FP-64A package. ...
-
Renesas H8S/2128 Series - page 6
2 Screws (M2.0 x 12 mm) IC socket Cable head User system Socket cover Screws (M2.0 x 8 mm) and flat washers and flat washers (For fastening cable head) Figure 1 HS2128ECH61H User System Interface Cable ...
-
Renesas H8S/2128 Series - page 7
3 Table 1 lists t he HS2128ECH61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2128ECH61H Components No. Component Quantity Remarks 1 Cable body 1 Includes flat cable 2 Cable head 1 3 IC socket 1 For the FP-64A package 4 Socket cover 1 For installing an FP-64A packaged MCU 5 Screws (M2 x 12 mm) 4 For fas ...
-
Renesas H8S/2128 Series - page 8
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so w ill damage ...
-
Renesas H8S/2128 Series - page 9
2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so w ill damage the user system and the emulator pro ...
-
Renesas H8S/2128 Series - page 10
6 2.2.4 Fastening Cable Head CAUTION 1. Use a Phillips-type screwdriver whose head matches the screw head. 2. The tightening torque must be 0.0785 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a sc ...
-
Renesas H8S/2128 Series - page 11
Screws (M2.0 x 12 mm) and flat washers Cable head Pin 1 IC socket (IC149-064-008-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Figure 3 Connecting User System Interface Cable to User System 7 ...
-
Renesas H8S/2128 Series - page 12
2.2.5 Connecting Cable Body to Cabl e Head Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 4 Fastening Cable Body 8 ...
-
Renesas H8S/2128 Series - page 13
2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an FP-64A package (IC149-064-008-B5: m anufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that the dimensions in figure 5 are somewh at different from those of the actual chip&ap ...
-
Renesas H8S/2128 Series - page 14
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 6. Unit: mm Tolerance: –0.5 mm Figure 6 Dimensions for User System Interface Cable Head 10 ...
-
Renesas H8S/2128 Series - page 15
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 7. 9.4 Unit: mm Tolerance: ± 0.5 mm User system IC socket (IC149-064-008-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) Figure 7 Resulting Dimensions aft ...
-
Renesas H8S/2128 Series - page 16
12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Phillips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.0785 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw become ...
-
Renesas H8S/2128 Series - page 17
MCU Pin 1 mark User system Socket cover IC socket (IC149-064-008-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) Figure 8 Installing MCU to User System 13 ...
-
Renesas H8S/2128 Series - page 18
Section 4 Verifying Operation 1. When using the E6000 emulator (HS2148EPI61H) for t he H8S/2148, H8S/2138, H8S/2128 series, turn on the emulator according to the procedures described in the H8S Series E6000 Emulator User' s Manual (HS2000EPI61HE). 2. Verify the user system interface cable connec tions by accessing the exte rnal m emory and por ...
-
Renesas H8S/2128 Series - page 19
Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU. 3. This user system interface cable is specifi ...
Do you have a question concerning Renesas H8S/2128 Series?
Use the form below
If you did not solve your problem by using a manual Renesas H8S/2128 Series, ask a question using the form below. If a user had a similar problem with Renesas H8S/2128 Series it is likely that he will want to share the way to solve it.