English dropdown-ico

Manual Dell P14T

81 pages 11.68 mb
Download

Go to site of 81

Summary
  • Dell P14T - page 1

    Dell Latitude E6230 Owner's Manual Regulatory Model: P14T Regulatory Type: P14T001 ...

  • Dell P14T - page 2

    Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc ...

  • Dell P14T - page 3

    Contents 1 Working on Your Computer....................................................................................................... 7 Before Working Inside Your Computer ..................................................................................................................... 7 Turning Off Your Computer ........................... ...

  • Dell P14T - page 4

    Installing the Hall Sensor ........................................................................................................................................ 34 Removing the Coin-Cell Battery .............................................................................................................................. 35 Installing the Coin-Ce ...

  • Dell P14T - page 5

    7 Technical Specifications......................................................................................................... 75 8 Contacting Dell.......................................................................................................................... 81 ...

  • Dell P14T - page 6

    6 ...

  • Dell P14T - page 7

    1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that ...

  • Dell P14T - page 8

    NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9. Open the display. 10. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet befor ...

  • Dell P14T - page 9

    After Working Inside Your Computer After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers. 1. Connect any ...

  • Dell P14T - page 10

    10 ...

  • Dell P14T - page 11

    2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • Phillips screwdriver • Small plastic scribe Removing the Secure Digital (SD) Card 1. ...

  • Dell P14T - page 12

    3. Slide the ExpressCard out of the computer. Installing the ExpressCard 1. Slide the ExpressCard into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Removing The Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Slide the release latches to unlock the battery. 3. Remo ...

  • Dell P14T - page 13

    Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Removing the Subscriber Identity Module (SIM) Card 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the battery. 3. Remove the SIM card from the computer. Installing the Sub ...

  • Dell P14T - page 14

    4. Slide the base cover out of the computer. Installing the Base Cover 1. Place the base cover to align with the screw hole correctly on the computer. 2. Tighten the screw to secure the base cover to the computer. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer . Removing the Bluetooth Module 1. Follow the pro ...

  • Dell P14T - page 15

    4. Remove the screw that secures the bluetooth module to the computer. 5. Remove the bluetooth module. 15 ...

  • Dell P14T - page 16

    Installing the Bluetooth Module 1. Connect the bluetooth cable to its connector. 2. Tighten the screw to secure the bluetooth module to the computer. 3. Install the: a) base cover b) battery c) ExpressCard d) SD card 4. Follow the procedures in After Working Inside Your Computer . Removing the Hard Drive 1. Follow the procedures in Before Working I ...

  • Dell P14T - page 17

    6. Remove the hard drive. 7. Remove the hard-drive connector from the hard drive. 8. Remove the hard-drive caddy from the hard drive. 17 ...

  • Dell P14T - page 18

    Installing the Hard Drive 1. Attach the hard-drive caddy to the hard drive. 2. Connect the hard-drive connector. 3. Replace the hard drive in its slot. 4. Replace the hard-drive bracket to secure the hard drive. 5. Tighten the screws to secure the hard drive to the computer. 6. Install the: a) cover b) battery 7. Follow the procedures in After Work ...

  • Dell P14T - page 19

    5. Repeat steps 2 and 3 to remove the second memory module. Installing the Memory 1. Insert the memory module into the socket. 2. Press the retention clips to secure the memory module to the system board. 3. Install the: a) base cover b) battery 4. Follow the procedures in After Working Inside Your Computer . Removing The Palmrest 1. Follow the pro ...

  • Dell P14T - page 20

    5. Disconnect the touchpad cable. 6. Remove the screws that secures the palmrest to the computer. 7. Flip the base of the computer to a 45–degree angle. 20 ...

  • Dell P14T - page 21

    8. Press downward on the palmrest from the base of the computer. 9. Remove the palmrest. 21 ...

  • Dell P14T - page 22

    Installing the Palmrest 1. Align the palmrest to its slot. 2. Press along the sides of the palmrest until it snaps in place. 3. Flip the computer and tighten the screws that secures the palmrest in place. 4. Connect the following cables: a) touchpad b) Smart Card reader c) SD card reader 5. Install the: a) cover b) battery 6. Follow the procedures ...

  • Dell P14T - page 23

    5. Flip the keyboard over. 6. Disconnect the keyboard data cable. 7. Remove the keyboard. 8. Peel off the mylar tape. 23 ...

  • Dell P14T - page 24

    9. Disconnect the keyboard cable. Installing the Keyboard 1. Connect the keyboard cable. 2. Affix the mylar tape to the keyboard. 3. Connect the keyboard data cable. 4. Slide the keyboard into its compartment and ensure that it snaps into place. 5. Tighten the screws to secure the keyboard. 6. Flip the computer and tighten the screws at the bottom ...

  • Dell P14T - page 25

    b) ExpressCard c) battery d) base cover 3. Disconnect the antenna cables from the WLAN card by pulling it upwards. 4. Remove the screw that secures the WLAN card to the computer. 5. Slide and remove the WLAN card out from its slot on the system board. 25 ...

  • Dell P14T - page 26

    Installing the Wireless Local Access Network (WLAN) 1. Insert the WLAN card into its connector at a 45–degree angle into its slot. 2. Tighten the screw to secure the WLAN card to the computer 3. Connect the antenna cables to their respective connectors marked on the WLAN card. 4. Install the: a) base cover b) battery c) ExpressCard d) SD Card 5. ...

  • Dell P14T - page 27

    4. Remove the screws that secure the heat-sink fan to the computer. 5. Lift and remove the heat-sink fan. Installing the Heat-Sink Fan 1. Replace the heat-sink fan in its slot. 2. Tighten the screws that secure the heat-sink fan to the computer. 3. Connect the heat-sink fan cable. 27 ...

  • Dell P14T - page 28

    4. Install the: a) base cover b) battery c) ExpressCard d) SD card 5. Follow the procedures in After Working Inside Your Computer . Removing the Heat-Sink Module 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) SD Card b) ExpressCard c) battery d) base cover e) heat sink 3. Loosen the screws that secure the heat-s ...

  • Dell P14T - page 29

    Installing the Heat-Sink module 1. Replace the heat-sink module in its slot. 2. Tighten the screws to secure the heat-sink module. 3. Install the: a) heat-sink fan b) base cover c) battery d) ExpressCard e) SD Card 4. Follow the procedures in After Working Inside Your Computer . Removing the Speakers 1. Follow the procedures in Before Working Insid ...

  • Dell P14T - page 30

    5. Remove the screws that secure the speaker to the computer. 6. Remove the screws that secure the other speaker to the computer. 7. Remove the speakers. 30 ...

  • Dell P14T - page 31

    Installing the Speakers 1. Align the speakers in the original position and connect the speaker cables. 2. Tighten the screws to secure both the speakers 3. Install the: a) base cover b) battery c) ExpressCard d) SD card 4. Follow the procedures in After Working Inside Your Computer . Removing the Chassis Base 1. Follow the procedures in Before Work ...

  • Dell P14T - page 32

    4. Disconnect the hall sensor cable. 5. Remove the screws that secure the chassis base. 6. Pull up the chassis base. 32 ...

  • Dell P14T - page 33

    Installing the Chassis Base 1. Align the chassis base to the computer. 2. Tighten the screws to secure the chassis base to the computer. 3. Connect the following cables: a) hall sensor b) touchpad 4. Install the: a) speakers b) heat-sink fan c) bluetooth module d) keyboard e) palmrest f) base cover g) battery h) ExpressCard i) SD card 5. Follow the ...

  • Dell P14T - page 34

    j) base chassis 3. Unthread the hall sensor cable from the routing channel. 4. Remove the screw that secures the hall sensor. 5. Remove the hall sensor. Installing the Hall Sensor 1. Replace the hall sensor in its slot. 2. Tighten the screw to secure the hall sensor. 3. Route and connect the hall sensor cable. 4. Install the: a) base chassis 34 ...

  • Dell P14T - page 35

    b) speakers c) heat-sink fan d) bluetooth module e) keyboard f) palmrest g) base cover h) battery i) ExpressCard j) SD card 5. Follow the procedures in After Working Inside Your Computer . Removing the Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) SD Card b) ExpressCard c) battery d) cover e) ...

  • Dell P14T - page 36

    Installing the Coin-Cell Battery 1. Replace the coin-cell battery in its slot in the computer. 2. Connect the coin-cell battery cable. 3. Install the: a) base chassis b) speakers c) bluetooth module d) heat-sink fan e) keyboard f) palmrest g) base cover h) battery i) ExpressCard j) SD card 4. Follow the procedures in After Working Inside Your Compu ...

  • Dell P14T - page 37

    4. Disconnect the ExpressCard cage cable. 5. Disconnect the power-connector cable. 6. Remove the screws that secure the system board to the computer. 7. Lift the left edge of the system board and raise it to a 45-degree angle. 37 ...

  • Dell P14T - page 38

    8. Remove the system board. Installing the System Board 1. Place the system board in its compartment. 2. Tighten the screws to secure the system board to the computer. 3. Connect the following cables: a) power connector b) ExpressCard cage c) WiFi-switch board 4. Install the: a) chassis base b) display assembly c) speakers d) heat-sink fan e) heat ...

  • Dell P14T - page 39

    h) palmrest i) base cover j) battery k) ExpressCard l) SD card 5. Follow the procedures in After Working Inside Your Computer . Removing the Power-Connector Port 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) SD card b) ExpressCard c) battery d) base cover e) palmrest f) keyboard g) bluetooth module h) heat-sink ...

  • Dell P14T - page 40

    Installing the Power-Connector Port 1. Insert the power-connector port in its slot. 2. Connect the power connector to the system board. 3. Install the: a) base chassis b) speakers c) heat-sink module d) heat-sink fan e) bluetooth module f) keyboard g) palmrest h) base cover i) battery j) ExpressCard k) SD card 4. Follow the procedures in After Work ...

  • Dell P14T - page 41

    4. Remove the screws that secure the ExpressCard cage to the computer. 5. Remove the ExpressCard cage. 41 ...

  • Dell P14T - page 42

    Installing the ExpressCard Cage 1. Insert the ExpressCard cage into its compartment. 2. Tighten the screws to secure the ExpressCard cage to the computer 3. Connect the ExpressCard reader cable. 4. Install the: a) base chassis b) speakers c) heatsink d) bluetooth module e) keyboard f) palmrest g) base cover h) battery i) ExpressCard j) SD card 5. F ...

  • Dell P14T - page 43

    5. Remove the WiFi-switch board. Installing the WiFi-Switch Board 1. Place the WiFi-switch board in its compartment. 2. Tighten the screw to secures the WiFi-switch board to the computer. 3. Connect the WiFi-switch board cable. 4. Install the: a) base chassis b) speakers c) heat-sink fan d) bluetooth module e) keyboard f) palmrest g) base cover h) ...

  • Dell P14T - page 44

    Removing the Smart Card Cage 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) SD card b) ExpressCard c) battery d) base cover e) palmrest f) keyboard g) heat-sink fan h) bluetooth module i) speakers j) display assembly k) lower chassis l) system board 3. Remove the screw that secures the smart card cage to the com ...

  • Dell P14T - page 45

    Installing the Smart Card Cage 1. Place the smart card cage in its compartment. 2. Tighten the screw that secures the smart card cage to the computer. 3. Install the: a) system board b) base chassis c) display assembly d) speakers e) bluetooth module f) heat-sink fan g) keyboard h) palmrest i) base cover j) battery k) ExpressCard l) SD card 4. Foll ...

  • Dell P14T - page 46

    5. Remove the display bezel from the display assembly. Installing the Display Bezel 1. Place the display bezel onto the display assembly. 2. Starting from the top corner, press on the display bezel and work around the entire bezel until is snaps onto the display assembly. 3. Press on the left and right edges of the display bezel. 4. Install the bat ...

  • Dell P14T - page 47

    4. Flip the display panel over. 5. Peel off the LVDS cable connector tape and disconnect the LVDS cable from the display panel. 6. Remove the display panel from the display assembly. 47 ...

  • Dell P14T - page 48

    Installing the Display Panel 1. Affix the LVDS cable connector tape and connect the LVDS cable to the display panel. 2. Place the display panel onto the display assembly. 3. Tighten the screws that secure the display panel to the display assembly. 4. Install the: a) display bezel b) battery 5. Follow the procedures in After Working Inside Your Comp ...

  • Dell P14T - page 49

    4. Disconnect any antenna cables that may be connected to the wireless solutions and remove them from the routing channels. 5. Remove the screws that secure the low-voltage differential signaling (LVDS) bracket to the computer. 6. Remove the LVDS bracket. 7. Disconnect the LVDS cable. 49 ...

  • Dell P14T - page 50

    8. Pull the antenna cables through the opening on top of the computer. 9. Remove the screws that secure the display assembly to the computer. 10. Pull up the display assembly from the chassis. 50 ...

  • Dell P14T - page 51

    Installing the Display Assembly 1. Place the display assembly on the computer. 2. Tighten the screws to secure the display assembly to the computer. 3. Route the antenna cables through the routing channel. 4. Connect the antenna cables to the computer. 5. Route and connect the LVDS cable. 6. Place the LVDS bracket in its slot. 7. Tighten the screws ...

  • Dell P14T - page 52

    4. Remove the screw that secures the camera to the display assembly. 5. Lift up the right edge of the camera. 6. Flip the camera outwards. 52 ...

  • Dell P14T - page 53

    7. Disconnect the camera cable and remove the camera. Installing the Camera 1. Install the camera in its slot on the display panel. 2. Tighten the screw to secure the camera to the display assembly. 3. Connect the camera cable to the camera. 4. Affix the conductive tape. 5. Install the: a) display bezel b) battery 6. Follow the procedures in After ...

  • Dell P14T - page 54

    f) keyboard g) display bezel h) display panel i) display assembly 3. Disconnect the LVDS and camera cable from the camera. 4. Peel back the adhesives that secures the LVDS and camera cable to the display assembly. 5. Remove the LVDS and camera cable from the display assembly. 54 ...

  • Dell P14T - page 55

    Installing the LVDS and Camera Cable 1. Affix the LVDS and camera cable to the display assembly. 2. Connect the LVDS and camera cable. 3. Install the: a) display assembly b) display panel c) display bezel d) keyboard e) palmrest f) base cover g) battery h) ExpressCard i) SD card 4. Follow the procedures in After Working Inside Your Computer . 55 ...

  • Dell P14T - page 56

    56 ...

  • Dell P14T - page 57

    3 Additional Information This section provides information for the additional features that are part of your computer. Docking Port Information The docking port is used for connecting the laptop to a docking station (optional). 1. Docking Port 57 ...

  • Dell P14T - page 58

    58 ...

  • Dell P14T - page 59

    4 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardware • View the system hardware configuration • Enable or disable integrated devices • Set performance and power management thresholds • Manage ...

  • Dell P14T - page 60

    Keys Navigation <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable. <Tab> Moves to the next focus area. NOTE: For the standard graphics browser only. <Esc> Moves to the previous page till you view the main scr ...

  • Dell P14T - page 61

    Option Description • Disabled • Enabled • Enabled w/PXE (Default Setting) Parallel Port Allows you to define and set how the parallel port on the docking station operates. You can set the parallel port to: • Disabled • AT • PS2 • ECP Serial Port Identifies and defines the serial port settings. You can set the serial port to: • Disab ...

  • Dell P14T - page 62

    Option Description • Enable SMART Reporting - This option is disabled by default. USB Configuration Allows you to define the USB configuration. The options are: • Enable Boot Support • Enable External USB Port Default Setting: both the options are enabled. USB PowerShare Allows you to configure the behavior of the USB PowerShare feature. The ...

  • Dell P14T - page 63

    Table 4. Video Option Description LCD Brightness Allows you to set the panel brightness when the ambient sensor is Off. Optimus Allows you to enable or disable the NVIDIA Optimus technology. • Enable Optimus - Default Setting. Table 5. Security Option Description Intel TXT (LT-SX) Configuration This option is disabled by default. Admin Password A ...

  • Dell P14T - page 64

    Option Description Default Setting: Enable CPU XD Support Computrace Allows you to activate or disable the optional Computrace software The options are: • Deactivate (Default Setting) • Disable • Activate NOTE: The Activate and Disable options will permanently activate or disable the feature and no further changes will be allowed CPU XD Suppo ...

  • Dell P14T - page 65

    Option Description Hyper-Thread Control Allows you to enable or disable the HyperThreading in the processor. Default Setting: Enabled Table 7. Power Management Option Description AC Behavior Allows the computer to power-uon automatically, when AC adapter is plugged. The option is disabled. • Wake on AC Auto On Time Allows you to set the time at w ...

  • Dell P14T - page 66

    Option Description • Custom Charge — you can set the percentage to which the battery must charge . NOTE: All charging modes may not be available for all the batteries. Battery Slice Configuration Allows you to define the how to charge the battery. The options are: • Standard Charge • Express Charge (Default Setting) Table 8. POST Behavior O ...

  • Dell P14T - page 67

    Table 9. Virtualization Support Option Description Virtualization This option specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel Virtualization technology. • Enable Intel Virtualization Technology - Default Setting. VT for Direct I/O Enables or disables the Virtual Machine Monitor ...

  • Dell P14T - page 68

    Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For laptops, ensure that your computer battery is fully charged and connected to a power outlet 1. Re-start the computer. 2. Go to dell.com/support . 3. Enter the Service Tag or Express Service Code and click Submit . ...

  • Dell P14T - page 69

    To enter a system setup, press <F2> immediately after a power-on or re-boot. 1. In the System BIOS or System Setup screen, select System Security and press <Enter>. The System Security screen appears. 2. In the System Security screen, verify that Password Status is Unlocked . 3. Select System Password , enter your system password, and p ...

  • Dell P14T - page 70

    70 ...

  • Dell P14T - page 71

    5 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel ...

  • Dell P14T - page 72

    72 ...

  • Dell P14T - page 73

    6 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Device Status Lights Table 13. Device Status Lights Turns on when you turn on the computer and blinks when the computer is in a power management mode. Turns on when the comp ...

  • Dell P14T - page 74

    Battery Status Lights If the computer is connected to an electrical outlet, the battery light operates as follows: Alternately blinking amber light and white light An unauthenticated or unsupported non-Dell AC adapter is attached to your laptop. Alternately blinking amber light with steady white light Temporary battery failure with AC adapter prese ...

  • Dell P14T - page 75

    7 Technical Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For comprehensive specification of your computer go to Specifications’ section in your Owner’s Manual available on the support site at dell.com/support . For more information about the configurat ...

  • Dell P14T - page 76

    Audio Internal high-definition audio External microphone-in/stereo headphones/external speakers connector Speakers two Internal speaker amplifier 1 W (RMS) per channel Volume controls keyboard function keys, program menus Video Type integrated on system board Controller Intel HD Graphics Communications Network adapter 10/100/1000 Mb/s Ethernet (RJ- ...

  • Dell P14T - page 77

    Display Latitude E6330 13.3" Dimensions: Latitude E6230 Height 300.90 mm (11.84 inches) Width 180.00 mm (7.08 inches) Diagonal 317.30 mm (12.49 inches) Active area (X/Y) 276.61mm x 155.52 mm Latitude E6330 Height 314.10 mm (12.36 inches) Width 188.70 mm (7.42 inches) Diagonal 336.60 mm (13.25 inches) Active area (X/Y) 293.42 mm x 164.97 mm Max ...

  • Dell P14T - page 78

    Battery • 6-cell (58 WHr) Lithium-ion battery Dimensions: 3-cell Depth 29.97 mm (1.18 inches) Height 19.80 mm (0.78 inch) Width 208.00 mm (8.19 inches) 6-cell Depth 54.10 mm (2.13 inches) Height 20.85 mm (0.82 inch) Width 214.00 mm (8.43 inches) Weight: 3-cell 172.37 g (0.38 lb) 6-cell 335.66 g (0.74 lb) Voltage 11.10 VDC Temperature range: Opera ...

  • Dell P14T - page 79

    Physical Latitude E6230 Latitude E6330 Height 22.40 mm to 24.70 mm (0.88 inch to 0.97 inch) 25.40 mm to 30.10 mm (1 inch to 1.19 inches) Width 309.00 mm (12.16 inches) 335.00 mm (13.19 inches) Depth 226.00 mm (8.89 inches) 223.30 mm (8.79 inches) Weight 1.43 kg (3.14 lb) 1.65 kg (3.64 lb) Environmental Temperature: Operating Latitude E6230 10 °C t ...

  • Dell P14T - page 80

    80 ...

  • Dell P14T - page 81

    8 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your are ...

Manufacturer Dell Category Laptop

Documents that we receive from a manufacturer of a Dell P14T can be divided into several groups. They are, among others:
- Dell technical drawings
- P14T manuals
- Dell product data sheets
- information booklets
- or energy labels Dell P14T
All of them are important, but the most important information from the point of view of use of the device are in the user manual Dell P14T.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Dell P14T, service manual, brief instructions and user manuals Dell P14T. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Dell P14T.

Similar manuals

A complete manual for the device Dell P14T, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Dell P14T by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Dell P14T.

A complete Dell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Dell P14T - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Dell P14T, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Dell P14T, that we can find in the current document
3. Tips how to use the basic functions of the device Dell P14T - which should help us in our first steps of using Dell P14T
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Dell P14T
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Dell P14T in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Dell P14T?

Use the form below

If you did not solve your problem by using a manual Dell P14T, ask a question using the form below. If a user had a similar problem with Dell P14T it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)