English dropdown-ico

Manual Grizzly G0574

32 pages 1.49 mb
Download

Go to site of 32

Summary
  • Grizzly G0574 - page 1

    IN TR OD UC TI ON The Model G0574 Radiusing Sander is based on the Model G1140 Edge Sander with the addition of the radiusing attachment. Refer to the G1140 Edge Sander manual for the sanding unit assembly instructions and refer to the included G0577 Radiusing Attachment manual for radiusing attachment installation instructions. The Model G0574 DOE ...

  • Grizzly G0574 - page 2

    EDGE SANDER MODEL G1140 INSTRUCTION MANUAL COPYRIGHT © 1996 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED APRIL, 1999. PRINTED IN U.S.A. ...

  • Grizzly G0574 - page 3

    ...

  • Grizzly G0574 - page 4

    G1140 Edge Sander -C- Table Of Contents PAGE 1. SAFETY RULES SAFETY RULES FOR POWER TOOLS ................................................................................1-2 SAFETY RULES FOR SANDERS ............................................................................................3 2. CIRCUIT REQUIREMENTS 220V/110V OPERATION.............. ...

  • Grizzly G0574 - page 5

    G1140 Edge Sander -1- Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORS AWAY . All children and visitors should be kept a safe distance from work area. 6. MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. DON’T FORCE TOOL . It will do the job better and safer at the rate f ...

  • Grizzly G0574 - page 6

    -2- G1140 Edge Sander 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension ...

  • Grizzly G0574 - page 7

    G1140 Edge Sander -3- 6. TURN OFF THE SANDER WHEN NOT IN USE. Never leave a machine running unattended. 7. DO NOT stand directly in line with sanding accessories when turning the machine on. 8. DO NOT force the workpiece against the belt during operation. Firmly grasp the workpiece in both hands and ease it against the belt using light pressure. 9. ...

  • Grizzly G0574 - page 8

    -4- G1140 Edge Sander The Model G1140 will draw approximately 8 amps at 220V and 16 amps at 110V. Circuit pro- tection when operating at 220V should be on a breaker rated at 15 amps or a fuse rated at 20 amps. At 110V a 20 amp slow-blow fuse or breaker should be used. Fusing at amperage rat- ings higher than these will not adequately protect the mo ...

  • Grizzly G0574 - page 9

    G1140 Edge Sander -5- We do not recommend the use of extension cords on 220V equipment. It is much better to arrange the placement of your equipment and the installed wiring to eliminate the need for exten- sion cords. Should it be necessary to use an extension make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in Sect ...

  • Grizzly G0574 - page 10

    -6- G1140 Edge Sander Commentary SECTION 3: GENERAL INFORMATION We are proud to offer the Grizzly Model G1140 Edge Sander. The Model G1140 is part of a grow- ing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble- free, enjoyable operation and proof of Grizzl ...

  • Grizzly G0574 - page 11

    G1140 Edge Sander -7- Unpacking This G1140 Edge Sander is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, and the truck and driver are gone, you will need to file a freight claim with the carrier. Save the containers and all packing mate- rials for possible inspe ...

  • Grizzly G0574 - page 12

    -8- G1140 Edge Sander Site Considerations 1. Floor Load: Your G1140 Sander represents a large weight load in a small footprint. Most commercial floors are suitable for the Model G1140. Some residential floors may require additional build up to support both machine and operator. 2. Working Clearances: Consider existing and anticipated needs, size of ...

  • Grizzly G0574 - page 13

    G1140 Edge Sander -9- Beginning Assembly Assembly of the G1140 is straightforward. We have organized the assembly process into steps. Please follow them in sequence. Tools Required: Only a few common tools are needed to assemble this machine. Specifically, a 6" adjustable wrench, 12mm open end wrench, regular and Phillips ® screwdriver and an ...

  • Grizzly G0574 - page 14

    -10- G1140 Edge Sander Figure 4. Lead screw bracket Installed. Figure 5. Installing the horizontal brace. Figure 7. Horizontal / vertical brace installed. Working Table 1. Bolt the lead screw bracket to the front of the stand using the four Hex Bolts already threaded in place. See Figure 4. 2. Thread the horizontal brace into position, but do not t ...

  • Grizzly G0574 - page 15

    G1140 Edge Sander -11- Figure 8. Checking table bracket for parallelism. Figure 9. Table trunnions installed. 6. Measure the table bracket to the stand to assure it is parallel to the stand. See Figure 8. If the bracket is not parallel, remove the vertical brace, thread the horizontal brace in or out an appropriate amount and reinstall the vertical ...

  • Grizzly G0574 - page 16

    -12- G1140 Edge Sander Figure 13. Installing the quick release lever. Quick Release Lever 1. Loosen the belt tracking lock knob located at the top left of the machine. 2. Slide the quick release lever through the slot on the top of the platen cover. Thread it into place until it bottoms out. See Figure 13. It may be necessary to have an assistant p ...

  • Grizzly G0574 - page 17

    G1140 Edge Sander -13- Figure 14. Installing the auxiliary table. Auxiliary Table Figure 15. Dust hood mounted in place. Dust Hood Bolt the dust hood on using the hex bolts already threaded in place. See Figure 15. Slide the auxiliary table into place as pictured in Figure 14. Tighten the two thumb screws when table is at desired working height. It ...

  • Grizzly G0574 - page 18

    -14- G1140 Edge Sander Figure 16. Back stop properly installed. Back Stop Attach the back stop as shown in Figure 16. Set the back stop no more than 1 ⁄ 8 '' from the sandpa- per. This will prevent objects from being jammed between the back stop and the platen causing a potentially dangerous situation. Figure 17. Sander ready for belt i ...

  • Grizzly G0574 - page 19

    G1140 Edge Sander -15- Belt Tracking SECTION 5: ADJUSTMENTS Figure 19. Location of tracking knob. 1. Carefully move the belt left to right by hand and adjust the tracking knob as necessary to achieve proper tracking. See Figure 19. 2. Before beginning this step, read the entitled Test Run on page 18. Connect to power and turn the machine on and off ...

  • Grizzly G0574 - page 20

    -16- G1140 Edge Sander Table Tilt Figure 21. Table tilt adjustment. 1. Loosen the lock handles, tilt the working table to the desired angle and retighten the lock handles. See Figure 21. 2. It may be necessary to re-adjust the working table closer to the platen. Not more than a 1 ⁄ 4 '' gap should exist between the platen and the workin ...

  • Grizzly G0574 - page 21

    G1140 Edge Sander -17- Platen Tilt Figure 23. Platen lock bolt. Figure 24. Platen tilted over 90 ˚. 1. Loosen the lock bolt shown in Figure 23. 2. Carefully tilt the platen assembly over. Figure 24. 3. After returning the platen assembly back to its upright position, retighten the lock bolt depicted in Figure 23. Belt Tension Figure 25. Belt tensi ...

  • Grizzly G0574 - page 22

    -18- G1140 Edge Sander SECTION 6: OPERATIONS Edge & End Sanding Figure 26. Typical edge sanding method. Figure 26 depicts a typical edge sanding process. The back stop can be used for shorter workpieces if so desired. Once the assembly is complete and the adjust- ments are done to your satisfaction, you are ready to test the machine. Turn on th ...

  • Grizzly G0574 - page 23

    G1140 Edge Sander -19- Figure 28. Typical face sanding method. Figure 29. Typical contour sanding method. Horizontal Sanding When face sanding, tilt the platen so it is hori- zontal and use the back stop to hold your work- piece. Apply even hand pressure while moving the workpiece back and forth for even belt wear. When contour sanding, adjust the ...

  • Grizzly G0574 - page 24

    -20- G1140 Edge Sander SECTION 7: MAINTENANCE Lubrication Table Shielded and pre-lubricated ball bearings require no lubrication for the life of the bearings. In a con- tinuous-use environment, expect the bearings to last for several years. With intermittent use, bear- ings can be expected to last much longer. All bearings are standard sizes and ca ...

  • Grizzly G0574 - page 25

    G1140 Edge Sander -21- The following pages contain general machine data, parts diagrams/lists, troubleshooting guide and Warranty/Return information for your Model G1140 Edge Sander. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained service tech ...

  • Grizzly G0574 - page 26

    -22- G1140 Edge Sander Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 GRIZZLY MODEL G1140 HEAVY DUTY EDGE SANDER MACHINE DATA SHEET Design Type .......................................................... Tilting Head Edge Sander, Floor Model Overall Dimensions and Specifications: Table Size ........... ...

  • Grizzly G0574 - page 27

    G1140 Edge Sander -23- WHITE RED BLACK YELLOW MOTOR WIRES 110 VOLT GREEN (GROUND) TO 110 VOLT POWER SUPPLY RED WHITE BLACK YELLOW MOTOR WIRES 220VOLT GREEN (GROUND) TO 220 VOLT POWER SUPPLY NOTE: THE WIRES FROM THE POWER SUPPLY, EXCEPT THE GREEN GROUND WIRE, ARE INTERCHANGABLE, THEREFORE COLORS ARE NOT SPECIFIED. ...

  • Grizzly G0574 - page 28

    -24- G1140 Edge Sander 1 16 64 102 101 19 18 22 25 35A 4 27 32 72 98 74 81 91 97 97 69 71 73 66 65 74 41 42 17 23 26 38 39 29 30 35A 24 76 6 7 75 95 8 5 104 78 100 47 48 79 92 51 68 67 51 55 103 63 60 76 56 52 57 58 78 50 78 80 50 63 103 49A 49 46A 44A 45 99 36 83 81 5 28 40 43 33 3 4 2 52 62 91 63 59 61 9 10 11 13 12 84 76 24 14 15 20A 21 20B 20C ...

  • Grizzly G0574 - page 29

    G1140 Edge Sander -25- 1 P1531001 PLATEN 2 P1140002 PLATEN COVER 3 PB24 HEX BOLT 3 / 8 ''-16 x 1 1 / 4 '' 4 PLW04 LOCK WASHER 3 / 8 '' 5 PSB14 CAP SCREW 3 / 8 ''-16 x 1'' 6 P1531006 DRIVER ROLLER 7 PN09 HEX NUT 5 / 8 ''-18 8 PLW06 LOCK WASHER 5 / 8 '' 9 PR02 EXT RETAINING RING 20 ...

  • Grizzly G0574 - page 30

    -26- G1140 Edge Sander Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warran ...

  • Grizzly G0574 - page 31

    G1140 Edge Sander CUT ALONG DOTTED LINE 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt ...

  • Grizzly G0574 - page 32

    -28- G1140 Edge Sander FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend: ...

Manufacturer Grizzly Category Sander

Documents that we receive from a manufacturer of a Grizzly G0574 can be divided into several groups. They are, among others:
- Grizzly technical drawings
- G0574 manuals
- Grizzly product data sheets
- information booklets
- or energy labels Grizzly G0574
All of them are important, but the most important information from the point of view of use of the device are in the user manual Grizzly G0574.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Grizzly G0574, service manual, brief instructions and user manuals Grizzly G0574. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Grizzly G0574.

Similar manuals

A complete manual for the device Grizzly G0574, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Grizzly G0574 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Grizzly G0574.

A complete Grizzly manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Grizzly G0574 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Grizzly G0574, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Grizzly G0574, that we can find in the current document
3. Tips how to use the basic functions of the device Grizzly G0574 - which should help us in our first steps of using Grizzly G0574
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Grizzly G0574
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Grizzly G0574 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Grizzly G0574?

Use the form below

If you did not solve your problem by using a manual Grizzly G0574, ask a question using the form below. If a user had a similar problem with Grizzly G0574 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)