English dropdown-ico

Manual Brinkmann 2500

32 pages 0.85 mb
Download

Go to site of 32

Summary
  • Brinkmann 2500 - page 1

    MAXIMUM SIDE BURNER LOAD = 15 lbs. 1. Read and follow all warnings and instructions in owner’s manual before lighting. 2. Open lid before lighting burner. 3. Make sure all control knobs are in the OFF position. 4. Select the burner to be lit. Push and turn the control knob of that burner to HIGH. 5. Press the electronic igniter and hold for 3-5 s ...

  • Brinkmann 2500 - page 2

    WE W ANT YOU T O ASSEMBLE AND USE YOUR GRILL AS SAFEL Y AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO A TTRACT YOUR A TTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL. WHEN YOU SEE THE SAFETY ALERT SYMBOL P A Y CLOSE A TTENTION TO THE INFORMA TION WHICH FOLLOWS! READ ALL SAFETY W ARNINGS AND INSTRUCTIONS CAREFULL Y BEFOR ...

  • Brinkmann 2500 - page 3

    2 W ARNING • Never use natural gas in a unit designed for liquid propane gas. • Never use charcoal briquets or lighter fluid in a gas grill. • Leak test all connections before first use, even if grill was purchased fully assembled and after each tank refill. • Never check for leaks using a match or open flame. CAUTION! Strong odors, colds, ...

  • Brinkmann 2500 - page 4

    CYLINDER SPECIFICA TIONS: When purchasing or exchanging a cylinder for your gas grill, it must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339 as applicable with a listed over-filling prevention device (OPD). 3 W ARNI ...

  • Brinkmann 2500 - page 5

    4 The cylinder must also be equipped with: • A shut-off valve terminating in a T ype 1 gas cylinder valve outlet. • A T ype 1 valve that prevents gas flow until a positive seal is obtained. • An arrangement for vapor withdrawal. • A collar to protect the cylinder shut-off valve. • A safety relief device having direct communication with th ...

  • Brinkmann 2500 - page 6

    FILLING THE LP GAS CYLINDER: • Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder . • New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank. • DO NOT allow the cylinder to be filled beyond 80% capacity . Over-filled tanks can create a dangerous condition. Over-filled tan ...

  • Brinkmann 2500 - page 7

    6 W ARNING • Never use your grill without leak testing all gas connections and hoses. See the section on "Leak T esting" in this manual for proper procedures. The pressure regulator and hose assembly supplied with your gas grill is designed to work with an LP gas supply cylinder . • DO NOT attempt to connect it to any other fuel suppl ...

  • Brinkmann 2500 - page 8

    LEAK TESTING: T o prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame. • Never perform a leak test while the grill is in use or while grill is still hot. WHEN TO PER ...

  • Brinkmann 2500 - page 9

    W ARNING 8 6. Check each place listed (A -K) for growing bubbles which indicates a leak. 7. T urn OFF gas supply at cylinder valve. 8. T urn on control knobs to release gas pressure in hose. 9. T urn control knobs to OFF position. 10. T ighten any leaking connections. 1 1. Repeat soapy water test until no leaks are detected. DO NOT use the grill if ...

  • Brinkmann 2500 - page 10

    LIGHTING INSTRUCTIONS: Follow the instructions exactly . 1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down. 2. Check that all burner control knobs and the cylinder valve are turned to the OFF position. 3. T urn on the fuel supply by rotating the ...

  • Brinkmann 2500 - page 11

    LIGHTING THE SIDE BURNER: 1. Open lid to the side burner before lighting. 2. T urn on the side burner by pressing in and rotating the control knob to the HIGH position. 3. Press and hold the igniter button on the main control panel for 3-5 seconds until the burner ignites. 4. If burner does not ignite immediately , turn the burner control knob to O ...

  • Brinkmann 2500 - page 12

    11 OPERA TING THE GRILL: Never use Charcoal or Lighter Fluid inside your Gas Grill. Read and follow all warnings and instructions contained in the preceding sections of this manual. BREAKING IN YOUR GRILL: • In manufacturing and preserving the components of your grill, oil residue may be present on the burner and cooking surfaces of your grill. ? ...

  • Brinkmann 2500 - page 13

    ROTISSERIE COOKING: • Y our grill was pre-drilled from factory to include mounting holes for a Brinkmann rotisserie (sold separately). Do not use a rotisserie not specifically manufactured for this grill. • Read and follow all instructions provided with the rotisserie. Save instructions for future reference. • Do not use the side burner when ...

  • Brinkmann 2500 - page 14

    TRANSPORTING AND STORAGE: • Never move a grill when it is hot or when objects are on the cooking surfaces. • Make sure that cylinder valve is shut off. After moving the grill check that all gas connections are free of leaks. Refer to instructions for leak test on page 7 of this manual. • DO NOT store a spare LP gas cylinder (filled or empty) ...

  • Brinkmann 2500 - page 15

    CASTINGS • Remove the cooking grills, heat shields, and burners from inside your grill. Use a brush with hot water and detergent to remove excess residue. NEVER use a commercial oven cleaner . Rinse completely with water . T owel dry and replace all components as described in the assembly instructions. BURNER ASSEMBL Y/MAINTENANCE • Although yo ...

  • Brinkmann 2500 - page 16

    TROUBLE SHOOTING: Problem: Possible Causes: • Burner will not light 1. Check LP cylinder fuel level. 2. Bad electrode spark. Check to see if the grill will “ match light. ” (See Page 9) Electrode or collector may need adjustment. 3. Burner may not be properly seated. 4. Burner may be obstructed. 5. The cylinder valve may be closed. 6. Regulat ...

  • Brinkmann 2500 - page 17

    16 • T o protect your grill from excessive rust, the unit must be kept clean and covered at all times when not in use. A grill cover may be ordered directly from Brinkmann by calling 1-800-468-5252 or 1-800-527-0717. • W ash cooking grills and heat shields with hot, soapy water , rinse well and dry . Lightly coat cooking grill with vegetable oi ...

  • Brinkmann 2500 - page 18

    ASSEMBL Y INSTRUCTIONS READ ALL SAFETY W ARNINGS & ASSEMBL Y INSTRUCTIONS CAREFULL Y BEFORE ASSEMBLING OR OPERA TING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT . The following provided tools are required to assemble this Brinkmann Pro Series 2500 Grill: • Flathead Screwdriver • Hex Nut Wrench 17 1 Back Cart ...

  • Brinkmann 2500 - page 19

    50 100 200 300 400 500 ° F OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW OFF HIGH LOW M A X IM U M S ID E B U R N E R L O A D = 1 5 l b s . 1 . R e a d a n d f o l l o w a l l w a r n i n g s a n d i n s t r u c t io n s i n o w n e r ’ s m a n u a l b e f o r e li g h t i n g . 2 . O p e n l i d b e f o r e l i g h ti n g s i ...

  • Brinkmann 2500 - page 20

    19 8 M6 X 12mm bolts 8 M6 X 20mm bolts 12 M6 X 50mm bolts P AR TS CARD CONTENTS Make sure you have all items listed under P ARTS LIST and P ARTS BAG CONTENTS before you begin the installation process. Y our Parts Bag will include: M6 X 12mm bolts M6 X 20mm bolts M6 X 50mm bolts AA /1.5V Alkaline battery Screwdriver Hex nut wrench 1 Screwdriver 1 He ...

  • Brinkmann 2500 - page 21

    Choose a good, cleared assembly area and get a friend to help you put your grill together . Lay cardboard down to protect grill finish and assembly area. Step 1 Assemble bottom cart panel and right side cart panel assembly by using four M6 X 50mm bolts (hand tighten only at this point). Step 2 Assemble bottom cart panel and left side cart panel ass ...

  • Brinkmann 2500 - page 22

    With the help of a friend, turn the cart over , try to minimize the stress to the side panels. Step 3 Attach locking casters to the bottom of the cart. T ighten caster bolts securely using hex nut wrench provided in parts pack. Note: With the help of a friend, turn the cart to its upright position. Step 4 Attach back cart panel by using four M6 X 5 ...

  • Brinkmann 2500 - page 23

    22 Step 5 Attach the grease tray bracket onto the back cart panel by inserting the three tabs into the slots on the back cart panel. Note: When performing Step 6, lift grill body from front and rear panels to avoid injury to hands and fingers. Step 6 With the help of a friend, place grill body assembly on grill cart. Grill body will rest on upper s ...

  • Brinkmann 2500 - page 24

    23 Step 7 Install door bracket using four M6 X 12mm bolts. Make sure door stop is set toward back of cart. Step 8 Insert right side door over lower pivot (on bottom cart panel) then align door with cart frame. Depress spring pin located on top edge of door and slide door toward side cart panel until spring pin locks into hole in door bracket. Repea ...

  • Brinkmann 2500 - page 25

    Step 9 Attach side burner assembly to grill body assembly by inserting four M6 X 20mm bolts halfway into the screw holes of the grill body assembly . Then slide side burner assembly onto bolts and secure all four bolts. Install side burner grate and control knob. Step 10 Remove the plastic cap on gas supply manifold and attach rubber gas hose to ga ...

  • Brinkmann 2500 - page 26

    25 Step 1 1 Attach side burner igniter lead to the electrode as illustrated. Step 12 Attach side table assembly to grill body assembly by inserting four M6 X 20mm bolts halfway into the screw holes of the grill body assembly . Then slide side table assembly onto bolts and secure all four bolts. Side T able Screw Holes Gas Hose Side Burner Igniter L ...

  • Brinkmann 2500 - page 27

    Step 13 Insert grill bottom into opening on backside of grill. Make sure to slide tray onto tracks as illustrated. Step 14 Slide grease tray into grease tray bracket located under grill bottom on backside of grill. 26 Grill Bottom Grease T ray ...

  • Brinkmann 2500 - page 28

    Step 15 Place the porcelain coated heat shields on lower level of grill body assembly directly above burners. Step 16 Place porcelain cast iron cooking grills on support ribs directly above porcelain heat shields. Step 17 Place warming rack in slots above cast iron cooking grills. 27 1. Read and follow all warnings and instructions in owner ’ s m ...

  • Brinkmann 2500 - page 29

    28 MAXIMUM SIDE BURNER LOAD = 15 lbs. 1. Read and follow all warnings and instructions in owner ’ s manual before lighting. 2. Open lid before lighting burner. 3. Make sure all control knobs are in the OFF position. 4. Select the burner to be lit. Push and turn the control knob of that burner to HIGH. 5. Press the electronic igniter and hold for ...

  • Brinkmann 2500 - page 30

    PROFESSIONAL SHISH-KABOB SKEWERS These heavy-duty , 18" shish-kabob skewers are extra-long for fabulous restaurant style kabobs. Made of rust resistant stainless steel to last for years. SET OF 12 812-2904-0 ACCESSORIES 29 RIB RACK Chrome-plated rack can greatly increase the cooking capacity of your grill. Holds ribs, chicken halves, potatoes ...

  • Brinkmann 2500 - page 31

    ACCESSORIES LOOK FOR THESE AND OTHER BRINKMANN ACCESSORIES A T YOUR LOCAL RET AILER WHERE SMOKERS ARE SOLD, OR ORDER DIRECT BY CALLING 1-800-468-5252. THE UL TIMA TE 5-PIECE BBQ TOOL SET Yo u ’ ll be the envy of your fellow outdoor chefs with this ultimate BBQ tool set. It ’ s sleek ergonomic design combined with durable, heavy- gauge stainless ...

  • Brinkmann 2500 - page 32

    140-2501-1 8/02, 10/03 Owner ’ s Manual for Model 810-2500-1 The Brinkmann Corporation warrants to the original purchaser that the Brinkmann Stainless Steel Pro Series 2500 TM is free from defects due to workmanship or materials for: Stainless steel and die cast parts - Lifetime Electronic ignition and burners - 10 Y ears Remaining parts - 1 Y ea ...

Manufacturer Brinkmann Category Gas Grill

Documents that we receive from a manufacturer of a Brinkmann 2500 can be divided into several groups. They are, among others:
- Brinkmann technical drawings
- 2500 manuals
- Brinkmann product data sheets
- information booklets
- or energy labels Brinkmann 2500
All of them are important, but the most important information from the point of view of use of the device are in the user manual Brinkmann 2500.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Brinkmann 2500, service manual, brief instructions and user manuals Brinkmann 2500. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Brinkmann 2500.

Similar manuals

A complete manual for the device Brinkmann 2500, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Brinkmann 2500 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Brinkmann 2500.

A complete Brinkmann manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Brinkmann 2500 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Brinkmann 2500, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Brinkmann 2500, that we can find in the current document
3. Tips how to use the basic functions of the device Brinkmann 2500 - which should help us in our first steps of using Brinkmann 2500
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Brinkmann 2500
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Brinkmann 2500 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Brinkmann 2500?

Use the form below

If you did not solve your problem by using a manual Brinkmann 2500, ask a question using the form below. If a user had a similar problem with Brinkmann 2500 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)