English dropdown-ico

Manual Grindmaster RAPS400E

36 pages 1.8 mb
Download

Go to site of 36

Summary
  • Grindmaster RAPS400E - page 1

    Shuttle Bre wer & Airpot/Shuttle Bre wer s Operation and Instruction Manual F or Models P300E, P400E, RAP300E, RAP400E, RAPS300E, RAPS400E Installation: See rough-in dra wings in this manual f or dimensions and locations of electric and water input. Set-Up/P osition 1) Remov e the brew er from the packing material and attach its legs. 2) P osit ...

  • Grindmaster RAPS400E - page 2

    Pag e 2 Shuttle Brewer s & Airpot/Shuttle Brewer s Installation (con't) Electric Hook-up 1) The electric ratings f or your bre wer are printed on its nameplate. T ypical electric ratings are: P300, P400, RAP300, RAP400 Optional 120/208V , 3.8kW , 18A or 120/240V 5.0kW , 21A, 1 phase Standard 120/208V , 5.0kW , 24A or 120/240V 6.6kW , 28A, ...

  • Grindmaster RAPS400E - page 3

    Pag e 3 Operation 1) RAPS Brew ers require the accessor y warmer base placed ov er the pegs on the brew shelf bef ore brewing into a shuttle . Plug the base into the receptacle on the side of the brew er . The receptacle is only energized when a shuttle is in place . 2) Place an empty , warm shuttle or air pot on the shelf , counter , or accessor y ...

  • Grindmaster RAPS400E - page 4

    Pag e 4 Adjustments All adjustable components are located under the top co v er . T o access these par ts: 1) Shut off the electric line to the brewer or unplug the bre wer . 2) Remov e the single screw f astening the top cov er . Remov e the top cov er . 3) Pull f orward and lift off the top co ver . Brew V olume , Brew Timer The brew v olume of t ...

  • Grindmaster RAPS400E - page 5

    Pag e 5 Two Batch Timer with Knob Adjustment, See Figure 2: This timer is adjustable from 15 seconds to 5 min utes. Locate the adjustment knobs under the top cov er . Set this timer by adjusting the knob . The batch selector s witch picks the adjustment potentiometer which the timer will see. Figure 2 T wo Batch Timer Two Batch Timer with Counter A ...

  • Grindmaster RAPS400E - page 6

    Pag e 6 T o Adjust the Bypass: 1) Shut off and open brew er as described at the beginning of the adjustments section. 2) Locate the bypass v alve f or the brew head you wish to adjust. V alve is on the right and front of the BREW v alve . 3) Open the v alve (counter cloc kwise) to the desired setting. Use the table belo w as a guide: BYP ASS SETTIN ...

  • Grindmaster RAPS400E - page 7

    Pag e 7 4) If the maximum temperature adjustment needs to be increased, insert a small flat screwdriver into the shaft. T ur n the calibration screw counter cloc kwise to increase the maximum temperature . Optional Solid State Thermostat: This control maintains temperature within 3°F . The adjustable range is from 155°F to 205°F . See Figure 6. ...

  • Grindmaster RAPS400E - page 8

    Pag e 8 Cleaning After Each Bre w: 1) Dispose of grounds and rinse brew bask et. 2) Rinse shuttle or air pot containers bef ore reuse. Every Day: 1) W ash brew basket with w ar m soap y water . The wire basket is remov able to aid cleaning. 2) Remov e spray head(s), located abo v e brew bask et(s), using glov es or a heavy to wel. W ash off coffee ...

  • Grindmaster RAPS400E - page 9

    Pag e 9 W eekly or Bi-W eekly , Depending on Use 1) Fill shuttles with one gallon, 2/3 full, of hot water . 2) P our into the shuttle liners the recommended concentration of ur n cleaner (e xcessiv e amounts of cleaner will attack the stainless steel). Ur n cleaners that ha ve been used successfully: DIP-IT , manuf actured by Economics Labor atorie ...

  • Grindmaster RAPS400E - page 10

    Pag e 1 0 Service (con't) Drain W ater T ank Alwa ys empty the tank before shipping. Note: Brew er ma y contain ov er 5 gallons of hot water . 1) Prepare a heat resistant container to drain tank w ater into . 2) Shut off pow er to the brewer . 3) Remov e the front access panel. 4) Pinch or clamp the silicone hose connected to fill v alve . 5) ...

  • Grindmaster RAPS400E - page 11

    Pag e 1 1 T r oubleshooting: Filling, Heating, and Bre wing Overfilling water tank even when power is off. Fill valv e not sealing properly . Fill valv e installed backw ards. W ater entering tank continuously , usually slowly . Look f or direction of arrow on v alv e body . Disassemble v alve and clean out dir t. V alve ma y need new plunger if se ...

  • Grindmaster RAPS400E - page 12

    Pag e 1 2 Shuttle Brewer s & Airpot/Shuttle Brewer s If you still need help, call our Technical Service Department at (502) 425-4776 or (800) 695-4500 (USA & Canada only) Monday thru Friday 8 am - 8 pm EST or an authorized service center in your area. Please have the model and serial numbers ready so that accurate information can be given. ...

  • Grindmaster RAPS400E - page 13

    Pag e 1 3 T r oubleshooting: Filling, Heating, and Bre wing Brewing Pr oblems The brewing system consists of the f ollowing components: • Star t and Stop , switches located in the top control panel. • Brew Timer , located in the top control section under the top cover . • Brew V alv e, located in the top control section under the top cov er . ...

  • Grindmaster RAPS400E - page 14

    Pag e 1 4 P ar ts Illustration for Models P300E & P400E Shuttle Brewer s & Airpot/Shuttle Brewer s Item Pa r t # Description Item Pa r t # Description 1 A545-034 LEG, 4” PLASTIC W/ SS FOOT 13 A725-081 BRASS SPRA Y TEE W/ BYP ASS TUBING 1 A545-015 LEG, 4” SS (OPTIONAL) 14 A530-009 BREW TIMER 0-8 MINUTES 2 A537-043 HO T W A TER F A UCET W ...

  • Grindmaster RAPS400E - page 15

    Pag e 1 5 P ar ts Illustration for Model RAP400E Shuttle Brewer s & Airpot/Shuttle Brewer s Item Pa r t # Description Item Pa r t # Description 1 A548-072 LEG, R UBBER (RAP400) 11 A515016 PILO T LIGHT 1 A545-004 LEG, PLASTIC 4” (OPTIONAL RAP 400) 12 A725-082 SPRA Y TEE KIT W/ BYP ASS PLUG 1 A548-090 LEG, PLASTIC PLUG (RAP300) 13 A530-009 BREW ...

  • Grindmaster RAPS400E - page 16

    Pag e 1 6 P ar ts Illustration for Model RAPS400E Shuttle Brewer s & Airpot/Shuttle Brewer s FR ONT Item Pa r t # Description Item Pa r t # Description 1 A545-034 LEG, 4” PLASTIC W/ SS FOOT 16 A725-081 BRASS SPRA Y TEE W/ BYP ASS TUBING 1 A545-015 LEG, 4” SS (OPTIONAL) 17 A585-021 SPRA Y TUBING 3/8” ID X 5/8”OD X 6”LG 2 A537-043 HO T ...

  • Grindmaster RAPS400E - page 17

    Pag e 1 7 Shuttle Brewer s & Airpot/Shuttle Brewer s TOP (COVER REMOVED) FRONT FRONT (COVER REMOVED) 5 4 3 2 1 11 10 16 20 22 9 17 19 18 23 15 14 13 12 8 7 6 21 P ar ts Illustration for Model VSB-400 Item Pa r t # Description Item Pa r t # Description 1 A545-034 LEG, 4” PLASTIC W/ SS FOO T 12 A725-081 SPRA Y TEE KIT W/ BYP ASS TUBING 1 A545-0 ...

  • Grindmaster RAPS400E - page 18

    P ar ts Illustration for Shuttle CS-LL Item Pa r t # Description 1 A537-053 F A UCET MODEL ES 2 A522078 SHANK W/ CHROME BONNET 3 A718-018 GA UGE ASSEMBL Y 4 A725-092 KIT , SHUTTLE LID A713-027 SS SHUTTLE CO VER (not shown)* 5 A548-142 LID RET AINING CLIP 6 A548-140 A61365 LID ST OPPER W/ O-RING * S.S . Cover used until A ugust 2001 1 2 3 4 5 6 A537 ...

  • Grindmaster RAPS400E - page 19

    Pag e 1 9 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model P-300 ...

  • Grindmaster RAPS400E - page 20

    Rough-In Drawing f or Model P-400 Pag e 2 0 Shuttle Brewer s & Airpot/Shuttle Brewer s ...

  • Grindmaster RAPS400E - page 21

    Pag e 2 1 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model RAP-300 ...

  • Grindmaster RAPS400E - page 22

    Rough-In Drawing f or Model RAP-400 Pag e 2 2 Shuttle Brewer s & Airpot/Shuttle Brewer s ...

  • Grindmaster RAPS400E - page 23

    Pag e 2 3 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model RAPS-300 ...

  • Grindmaster RAPS400E - page 24

    Pag e 2 4 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model RAPS-400 ...

  • Grindmaster RAPS400E - page 25

    Pag e 2 5 Shuttle Brewer s & Airpot/Shuttle Brewer s Rough-In Drawing f or Model VSB-300 W W W W W A TER IM S ...

  • Grindmaster RAPS400E - page 26

    Rough-In Drawing f or Model VSB-400 Pag e 2 6 Shuttle Brewer s & Airpot/Shuttle Brewer s ...

  • Grindmaster RAPS400E - page 27

    Pag e 2 7 Shuttle Brewer s & Airpot/Shuttle Brewer s Wiring Diagram f or P300E/P400E, with 1 Batch Timer NO TE: THIS DRAWING SHO WS COMPONENTS ON ST ANDARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS ...

  • Grindmaster RAPS400E - page 28

    Wiring Diagram f or P300E/P400E, with 2 Batch Timer NO TE: THIS DRAWING SHO WS COMPONENTS ON ST ANDARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS Pag e 2 8 Shuttle Brewer s & Airpot/Shuttle Brewer s ...

  • Grindmaster RAPS400E - page 29

    Pag e 2 9 Shuttle Brewer s & Airpot/Shuttle Brewer s Wiring Diagram f or RAP300E/400E NO TE: THIS DRAWING SHO WS COMPONENTS ON ST ANDARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS Drawing #091-545 ...

  • Grindmaster RAPS400E - page 30

    Wiring Diagram f or RAPS 300/400E NO TE: 1) TWO SETS OF RECEPT ACLE COMPONENTS ONL Y PRO VIDED ON TWIN RAPS400E MODEL. DELETE GR OUP IN D ASHED BO X FOR RAPS300E. 2) THIS DIAGRAM SHO WS COMPONENTS ON ST AN- D ARD MODEL ONL Y . SEE 091-548 FOR WIRING OF BREWER OPTIONS. Drawing #091-523 Shuttle Brewer s & Airpot/Shuttle Brewer s Pag e 3 0 ...

  • Grindmaster RAPS400E - page 31

    Pag e 3 1 Shuttle Brewer s & Airpot/Shuttle Brewer s Wiring Diagram #091-548 NO TE: 1) ONE GROUP OF WARMER COMPONENTS PER BREW HEAD ON P AND RAPS MODELS. 2) TRANSFORMER MUST BE USED WHEN NEUTRAL LINE IS NO T PRO VIDED . 3) IF MODEL RAP , DELETE W ARMER COMPONENTS. 4) IF MODEL IS RAPS, DELETE WARMER LIGHT AND REPLACE W ARMER ELEMENT WITH NEMA 6- ...

  • Grindmaster RAPS400E - page 32

    Wiring Diagram #091-182 T3 T3 T3 1 1 T4 A T2 T3 T3 T4 T4 T4 B T2 T3 T3 1 1 T1 C T3 T3 T3 T1 T1 T4 D T2 T3 T3 T1 T1 T4 E T2 T3 T3 T1 T1 T2 F NO TE: USE WIRE NUT FOR 1 - 1 CONNECTION 5000 W A TT / 240V HEA TERS * SEP ARA TE 120V REQUIRED FOR CONTR OLS (3 AMP LOAD) 2.0 KW - 120/208V - 1 PH - 3 WIRE - 9 AMPS 2.5 KW - 120/240V - 1 PH - 3 WIRE - 11 AMPS ...

  • Grindmaster RAPS400E - page 33

    Pag e 3 3 Shuttle Brewer s & Airpot/Shuttle Brewer s Notes ...

  • Grindmaster RAPS400E - page 34

    Pag e 3 4 Shuttle Brewer s & Airpot/Shuttle Brewer s Notes ...

  • Grindmaster RAPS400E - page 35

    Pag e 3 5 Shuttle Brewer s & Airpot/Shuttle Brewer s Notes ...

  • Grindmaster RAPS400E - page 36

    Grindmaster Corporation 4003 Collins Lane Louisville, KY 40245 USA (502) 425-4776 (800) 695-4500 F AX (502) 425-4664 www .grindmaster .com © Grindmaster Cor poration, 1995 PRINTED IN USA Shuttle Bre wer & Airpot/Shuttle Bre wer s W ARRANTY GENERAL W ARRANTY INFORMA TION Grindmaster Cor poration maintains the highest standard of quality control ...

Manufacturer Grindmaster Category Coffeemaker

Documents that we receive from a manufacturer of a Grindmaster RAPS400E can be divided into several groups. They are, among others:
- Grindmaster technical drawings
- RAPS400E manuals
- Grindmaster product data sheets
- information booklets
- or energy labels Grindmaster RAPS400E
All of them are important, but the most important information from the point of view of use of the device are in the user manual Grindmaster RAPS400E.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Grindmaster RAPS400E, service manual, brief instructions and user manuals Grindmaster RAPS400E. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Grindmaster RAPS400E.

Similar manuals

A complete manual for the device Grindmaster RAPS400E, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Grindmaster RAPS400E by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Grindmaster RAPS400E.

A complete Grindmaster manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Grindmaster RAPS400E - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Grindmaster RAPS400E, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Grindmaster RAPS400E, that we can find in the current document
3. Tips how to use the basic functions of the device Grindmaster RAPS400E - which should help us in our first steps of using Grindmaster RAPS400E
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Grindmaster RAPS400E
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Grindmaster RAPS400E in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Grindmaster RAPS400E?

Use the form below

If you did not solve your problem by using a manual Grindmaster RAPS400E, ask a question using the form below. If a user had a similar problem with Grindmaster RAPS400E it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)