English dropdown-ico

Manual Extron electronic IPL T SFI244

29 pages 3.4 mb
Download

Go to site of 29

Summary
  • Extron electronic IPL T SFI244 - page 1

    Setup Guide 68-1377-01 Rev . E 09 10 IPL T Series IP Link Ethernet Control Interfaces IP Link ® (IPL T S Series, IPL T SFI244, IPL T CR48) IMPORT ANT : Refer to www .extron.com for the complete user guide and installation instructions ...

  • Extron electronic IPL T SFI244 - page 2

    Safety Pr ecautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the pr esence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock. Caution ...

  • Extron electronic IPL T SFI244 - page 3

    FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause ...

  • Extron electronic IPL T SFI244 - page 4

    ...

  • Extron electronic IPL T SFI244 - page 5

    IPL T Series • Contents v Contents Introduction ....................................... 1 About this Guide ................................ 1 IPL T Series Products .......................... 1 IPL T S Series ................................... 1 IPL T SFI244 ..................................... 4 IPL T CR48 ...................................... ...

  • Extron electronic IPL T SFI244 - page 6

    IPL T Series • Contents vi ...

  • Extron electronic IPL T SFI244 - page 7

    IPL T Series • Introduction 1 Intr oduction This section gives an overview of the setup guide and describes the IPL T Series IP Link ® Ethernet Control Interfaces and the features of these products. T opics that are covered include:   About this Guide   IPL T Series Products   Global Configurator About this Guide This setup gu ...

  • Extron electronic IPL T SFI244 - page 8

    2 IPL T Series • Introduction IPL T S2 Features of the IPL T S2 include:   12 VDC, 1 A desktop power supply   RJ-45 Ethernet receptacle   T wo (2) 9-pin D RS-232, RS-422, or RS-485 serial ports - or - T wo (2) 3.5 millimeter captive screw RS-232 serial ports (common to the two 9-pin D serial ports)   Six (6) Ethernet contr ...

  • Extron electronic IPL T SFI244 - page 9

    3 IPL T Series • Introduction COM 3 LAN UID# 093012052 POWER 12V .5A MAX COM 2 COM 1 COM 2 Lighting Control Ethernet RS-232 RS-232 D VD Laptop VCR Remote User Control & Administrator Monitoring Projector TCP/IP Network Extron IPL T S4 Ethernet Control Interface with GlobalViewer software Extron MLC 206 MediaLink Controller Extron DISPLAY POWE ...

  • Extron electronic IPL T SFI244 - page 10

    4 IPL T Series • Introduction IPL T SFI244 Features of the IPL T SFI244 include:   12 VDC, 1 A desktop power supply   RJ-45 Ethernet receptacle   T wo (2) RS-232 serial ports   Four (4) flex I/O ports   Four (4) I/R ports   Six (6) Ethernet control ports Extron IPL T RL Y4 Relay box Lighting System COM1 TX RX ...

  • Extron electronic IPL T SFI244 - page 11

    5 IPL T Series • Introduction Blinds LAN POWER 12V 0.5A INPUT 2 1 3 4 5 6 7 8 1 2 3 4 Extron IPL T CR48 Ethernet Control Interface Projector Lighting System Screen Control Projector Lift Control TCP/IP Network GlobalView er ® A /V Resource Management and Re mote Con tro l Application Figure 3. T ypical IPL T CR48 Controller Application Global Co ...

  • Extron electronic IPL T SFI244 - page 12

    6 IPL T Series • Introduction Figure 4. Global Configurator Application Scr een Using GC you can configure a single room controller or create a Web-based remote monitoring system for hundreds of A/V devices in multiple locations. Y ou can configure an IPL T controller using GC without having the device physically connected to the A/V network. ...

  • Extron electronic IPL T SFI244 - page 13

    7 IPL T Series • Introduction System Requirements The miminum system requirements for the PC on which you install Global Configurator include:   Intel ® Pentium ® III, 1 GHz processor   Microsoft ® Windows ® XP SP2, Windows Vista ® , or Windows 7   Microsoft Internet Explorer ® 6.0 with ActiveX ® enabled NOTE: If ActiveX ...

  • Extron electronic IPL T SFI244 - page 14

    8 IPL T Series • Introduction T o install Global Configurator from an Extron Software Products Disk if Autorun is not enabled on your PC: 1. Insert the Extron Software Products Disk into the disk drive of your PC. 2. From the Windows desktop, open My Computer and select the appropriate disk drive. 3. Double-click launch.exe . 4. Wait for the Ext ...

  • Extron electronic IPL T SFI244 - page 15

    IPL T Series • Setup 9 Setup This section describes the hardware setup and configuration of the IPL T Series controllers. T opics that are covered include:   Front Panel Featur es   Rear Panel Features   Resetting the Controller   Connections and Wiring   Configuring for Network Communication   Configuring t ...

  • Extron electronic IPL T SFI244 - page 16

    10 IPL T Series • Setup e LINK LED — A green LED lights to indicate that the unit is connected to an active network. f ACT LED — A yellow LED lights to indicate that data is being sent or received. IPL T SFI244 IPL T SFI244 1 R 100 COM TX LINK ACT 2 RX 1 3 2 4 1 3 2 4 I/O IR 7 8 9 1 3 2 4 5 6 a Power LED — A green LED lights to indicate tha ...

  • Extron electronic IPL T SFI244 - page 17

    11 IPL T Series • Setup IPL T CR48 4 2 3 1 RELA Y 8 6 7 5 IPL T CR48 R 4 2 3 1 INPUT 100 LINK ACT 7 6 1 3 2 4 5 a Power LED — A green LED lights to indicate that the unit is receiving power . b Reset button — Recessed multiple function Reset button. See Resetting the Controller for more information. c Input LEDs — A green LED lights to indi ...

  • Extron electronic IPL T SFI244 - page 18

    12 IPL T Series • Setup IPL T SFI244 COM1 COM2 LAN POWER 12V .5A MAX FLEX I/O 2 1 3 4 1 IR 2 3 4 TX RX TX RX G S G S G S G S MAC: 00-05-A6-XX-XX-XX S/N: IPL T SFI244 6 2 1 5 3 4 a Power connection — Connect the supplied 12 VDC power supply b LAN port — RJ-45 receptacle for network connection c COM ports — 3.5 millimeter captive screw recept ...

  • Extron electronic IPL T SFI244 - page 19

    13 IPL T Series • Setup Resetting the Controller There are five reset modes (numbered 1, 2, 3, 4, 5 for the sake of comparison with other Extron IPL products) available by using the Reset button ( b ) on the front panel. The Reset button is recessed, so use of a pointed stylus, ballpoint pen, or Extron T weeker is suggested. CAUTION: Review the ...

  • Extron electronic IPL T SFI244 - page 20

    14 IPL T Series • Setup Connections and Wiring Power Connection T o connect the power supply: 1. Insert the 2-pole captive screw connector into the power supply receptacle on the rear panel of the controller . SECTION A–A Ridges Smooth Po wer Supply Output Cord A A 3/16” (5 mm) Max. Po wer Supply Receptacle DC Po wer Cord Captive Screw Connec ...

  • Extron electronic IPL T SFI244 - page 21

    15 IPL T Series • Setup A cable that is wired as T568A at one end and T568B at the other (Tx and Rx pairs reversed) is a "crosso ver" cable. A cable wired the same at both ends is called a "straight-through" cable, because no pin/pair assignments are swapped. 12345678 RJ-45 Connector Insert T wisted Pair Wires Pins: Crossover ...

  • Extron electronic IPL T SFI244 - page 22

    16 IPL T Series • Setup Captive screw connector The IPL T S2, IPL T S6, and IPL T SFI244 have COM ports with captive screw connectors. The two COM ports with captive screw connectors on the IPL T S2 are common to the two 9-pin D connectors. Only one connector can be used for each COM port. If you use a COM port captive screw connector , its 9-pin ...

  • Extron electronic IPL T SFI244 - page 23

    17 IPL T Series • Setup IR Ports The IPL T SFI244 has four IR ports for infrared device connection. Y ou can connect IR emitters or a wired IR control port of another device to send IR signals (with or without carrier frequencies) to display or source devices. See the diagram below for IR port wiring. IR 1 SGSG 2 IPL T SFI244 Rear Panel T o Proje ...

  • Extron electronic IPL T SFI244 - page 24

    18 IPL T Series • Setup Flex I/O Ports The IPL T SFI244 has four Flex I/O ports that can be configured as digital inputs, digital outputs, or analog inputs. When configured as digital inputs, the Flex I/O ports can connect to switches and sensors. When configured as digital outputs, the Flex I/O ports can drive devices that accept a TTL input ...

  • Extron electronic IPL T SFI244 - page 25

    19 IPL T Series • Setup Then, you must change the default settings of the controller (IP address, subnet mask, and [optional] administrator name and password) in order to use the controller on an intranet (LAN) or on the Internet. After you have set up the IPL T controller for network communication, you can reset the PC to its original network co ...

  • Extron electronic IPL T SFI244 - page 26

    20 IPL T Series • Setup 5. Execute a ping command by typing ping followed by a space and the new IP address at the command prompt. For example: ping 10.13.170.15 After issuing this command, the controller changes to the new address and starts responding to the ping requests, as described. Y ou must ping the IPL T controller in order for the IP ad ...

  • Extron electronic IPL T SFI244 - page 27

    21 IPL T Series • Setup ...

  • Extron electronic IPL T SFI244 - page 28

    USA, Canada, South America, and Central America: Extron USA 1001 East Ball Road Anaheim, CA 92805 U.S.A. Europe, Africa, and the Middle East: Extron Europe Hanzeboulevard 10 3825 PH Amersfoort The Netherlands Asia: Extron Asia 135 Joo Seng Road #04-01 PM Industrial Bldg. Singapore 368363 Singapore Japan: Extron Japan Kyodo Building, 16 Ichibancho C ...

  • Extron electronic IPL T SFI244 - page 29

    Extron USA - West Headquarters + 800.633.9876 Inside USA/Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East +800.633.9876 Inside USA/Canada Only +1.919.863.1794 +1.919.863.1797 FAX Extron Europe +800.3987.6673 Inside Europe Only +31.33.453.4040 +31.33.453.4050 FAX Extron Asia +800.7339.8766 Inside Asia Only +65.6383.4400 +65.6383.466 ...

Manufacturer Extron electronic Category Switch

Documents that we receive from a manufacturer of a Extron electronic IPL T SFI244 can be divided into several groups. They are, among others:
- Extron electronic technical drawings
- IPL T SFI244 manuals
- Extron electronic product data sheets
- information booklets
- or energy labels Extron electronic IPL T SFI244
All of them are important, but the most important information from the point of view of use of the device are in the user manual Extron electronic IPL T SFI244.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Extron electronic IPL T SFI244, service manual, brief instructions and user manuals Extron electronic IPL T SFI244. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Extron electronic IPL T SFI244.

Similar manuals

A complete manual for the device Extron electronic IPL T SFI244, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Extron electronic IPL T SFI244 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Extron electronic IPL T SFI244.

A complete Extron electronic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Extron electronic IPL T SFI244 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Extron electronic IPL T SFI244, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Extron electronic IPL T SFI244, that we can find in the current document
3. Tips how to use the basic functions of the device Extron electronic IPL T SFI244 - which should help us in our first steps of using Extron electronic IPL T SFI244
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Extron electronic IPL T SFI244
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Extron electronic IPL T SFI244 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Extron electronic IPL T SFI244?

Use the form below

If you did not solve your problem by using a manual Extron electronic IPL T SFI244, ask a question using the form below. If a user had a similar problem with Extron electronic IPL T SFI244 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)