English dropdown-ico

Manual Delta 36-545

22 pages 1.03 mb
Download

Go to site of 22

Summary
  • Delta 36-545 - page 1

    INSTRUCTION MANUAL 10" Motorized Bench Saw (Model 36-540 & Model 36-545 W/Stand) P ART NO. 899974-0010 Copyright © 2000 Delta Machinery ESP AÑOL: PÁGINA 23 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-888-848-5175 ( In Canada call ...

  • Delta 36-545 - page 2

    2 SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will con- siderably lessen the possibility of personal injury . However , if normal safety precautions a ...

  • Delta 36-545 - page 3

    SA VE THESE INSTRUCTIONS ADDITIONAL SAFETY RULES FOR CIRCULAR SA WS 3 14. DIRECTION OF FEED. Feed work into blade or cutter against the direction or r otation of the blade or cutter only . 15. DO NOT feed the material too fast while cutting. Feed the material only fast enough so that the blade will cut. 16. NEVER attempt to free a stalled saw blade ...

  • Delta 36-545 - page 4

    4 UNP ACKING Y our new saw is shipped complete in one container . Carefully unpack the saw and all loose items fr om the shipping container . Fig. 2, illustrates the saw removed from the container and Fig. 2A, illustrates all the loose items packed with the saw . Fig. 2 Fig. 2A 1 - Rip Fence 2 - M8 Hex Nut for Rip Fence 3 - Locking Handle for Rip F ...

  • Delta 36-545 - page 5

    5 30 37 38 36 39 32 35 31 33 34 Fig. 4 30 - Leg (4) 31 - 3/8” Flat W asher for Mounting Saw to Stand & for Assembling Stand (24) 32 - Foot (4) 33 - M8 Hex Nut for Mounting Saw to Stand & for Assembling Stand (20) 34 - M8 x 40mm Hex Screw for Mounting Saw to Stand (4) 35 - M8 x 20mm Carriage Bolts for Assembling Stand (16) 36 - 18-1/2” T ...

  • Delta 36-545 - page 6

    6 ASSEMBL Y INSTRUCTIONS Fig. 3A Fig. 3B Fig. 4 Fig. 5 4. Fasten handwheel (A) Fig. 5, to shaft using a M6 x 12mm screw (7) Fig. 2A. ASSEMBLING BLADE RAISING AND LOWERING HANDWHEEL 1. Insert M6 x 55 screw (9) Fig. 2A, thr ough handle (E) Fig. 3A, and assemble handle (E) to handwheel (A) by threading scr ew (D) clockwise into handwheel. 2. Fig. 3B, ...

  • Delta 36-545 - page 7

    Fig. 7 Fig. 10 Fig. 9 Fig. 8 Fig. 6 ASSEMBLING BLADE GUARD AND SPLIT- TER ASSEMBL Y 1. DISCONNECT THE SAW FROM THE POWER SOURCE. 2. IMPORT ANT : THE BLADE GUARD AND SPLITTER ASSEMBL Y MUST BE PROPERL Y ALIGNED TO THE SAW BLADE IN ORDER TO PREVENT KICKBACK. 3. Position the blade 90 degrees to the table and lock in place. 4. Fasten the splitter suppo ...

  • Delta 36-545 - page 8

    8 Fig. 13 Fig. 11 Fig. 12 Fig. 12B Fig. 12A 8. Assemble splitter (H) Fig. 11, to splitter support bracket (B) as shown using 3/4 inch-long hex head screw , external tooth washer , and flat washer (L). 9. Fasten splitter (H) Fig. 12, to splitter support bracket using flat washer , exter nal tooth lockwasher and wing nut (M). NOTE: Before tightening ...

  • Delta 36-545 - page 9

    Fig. 13A Fig. 13B Fig. 14 Fig. 15 Fig. 16 ASSEMBLING MITER GAGE HOLDER 1. DISCONNECT THE SAW FROM THE POWER SOURCE. 2. Assemble spring clip (E) Fig. 13A, to the miter gage holder (A) as shown using 10mm pan head screw (F), lockwasher and hex nut. NOTE: Hex nut (G) Fig. 13B, will fit into the recess at the back of the miter gage holder (A) to keep s ...

  • Delta 36-545 - page 10

    10 Fig. 17 Fig. 18A Fig. 18 Fig.19 Fig. 20 The saw MUST be properly secur ed to a supporting sur- face using the four mounting holes, two of which are shown at (A) Fig. 19. IMPORT ANT : A HOLE MUST BE PROVIDED IN THE SUPPORTING SURF ACE TO F ACILIT A TE SAWDUST F ALL-THRU AND REMOV AL. Squar e the saw on the supporting surface and mark the location ...

  • Delta 36-545 - page 11

    ASSEMBLING ST AND 1. Assemble the stand as shown in Fig. 20A, using 32 carriage bolts, flat washers and hex nuts. Do not com- pletely tighten the hardwar e at this time. Letters ar e stamped on the stand brackets for ease in assembly . A - T op front and rear brackets B - T op side brackets C - Bottom side brackets D - Bottom front and r ear bracke ...

  • Delta 36-545 - page 12

    12 CONNECTING SA W TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This cir cuit should not be less than #12 wir e and should be protected with a 20 amp fuse. Have a certified electrician r eplace or r epair a worn cord immediately . Befor e connecting the motor to a power line, make sure the switch is ...

  • Delta 36-545 - page 13

    Fig. 25 Fig. 24 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING SA W The on/off switch (A) Fig. 24, is located on the fr ont of the saw cabinet. T o tur n the saw “ON” move the switch (A) to the up position. T o tur n the saw “OFF” , move the switch (A) to the down position. LOCKING SWITCH IN THE “OFF” POSITION When the tool ...

  • Delta 36-545 - page 14

    14 Fig. 27 BLADE TIL TING CONTROL T o tilt the saw blade, loosen blade tilting lock handle (A) Fig. 27, move handwheel (B) until the blade is at the desired angle and tighten lock handle (A). NOTE: The lock handle (A) is spring-loaded and can be repositioned by pulling out on the handle (A) and repositioning it on the serrated stud located undernea ...

  • Delta 36-545 - page 15

    RIP FENCE OPERA TION AND ADJUSTMENTS 1. T o move the rip fence (A) Fig. 30, along the table, lift up fence locking lever (B), slide the fence to the desired location on the table and push down fence locking lever (B) to lock the fence in position. 2. A pointer is supplied to indicate the distance the fence is positioned away from the saw blade. If ...

  • Delta 36-545 - page 16

    16 Fig. 32 Fig. 33 Fig. 34 Fig. 35 ADJUSTING BLADE P ARALLEL TO MITER GAGE SLOTS The blade was adjusted parallel to the miter gage slots at the factory . In or der to insure accurate cuts and help pr e- vent kickback when cutting, this adjustment should be rechecked and if necessary , readjusted as follows: 1. DISCONNECT THE TOOL FROM THE POWER SOU ...

  • Delta 36-545 - page 17

    OPERA TION Common sawing operations include ripping and cross-cutting plus a few other standar d opera- tions of a fundamental nature. As with all power tools, ther e is a certain amount of hazar d involved with the operation and use of the tool. Using the tool with the respect and caution demanded as far as safety precautions ar e concerned, will ...

  • Delta 36-545 - page 18

    18 Fig. 37 RIPPING Ripping is the operation of making a length-wise cut through a boar d, as shown in Fig. 37, and the rip fence (A) is used to position and guide the work. One edge of the work rides against the rip fence while the flat side of the board r ests on the table. Since the work is pushed along the fence, it must have a straight edge and ...

  • Delta 36-545 - page 19

    Fig. 40 USING AUXILIAR Y WOOD F ACING ON RIP FENCE It is necessary when performing some special operations to add wood facing (A) Fig. 40, to one or both sides of the rip fence, as shown. The wood facing is attached to the fence with wood screws thr ough the holes in the fence. 3/4 inch stock is suitable for most work although an occasional job may ...

  • Delta 36-545 - page 20

    20 CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in Fig. 42. PUSH STICK MAKE FROM 1/2” OR 3/4” WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4” WOOD CUT OFF HERE ...

  • Delta 36-545 - page 21

    21 NOTES ...

  • Delta 36-545 - page 22

    22 P AR TS, SERVICE OR W ARRANTY ASSIST ANCE Delta Building T rades and Home Shop Machinery T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer r eturns ...

Manufacturer Delta Category Saw

Documents that we receive from a manufacturer of a Delta 36-545 can be divided into several groups. They are, among others:
- Delta technical drawings
- 36-545 manuals
- Delta product data sheets
- information booklets
- or energy labels Delta 36-545
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta 36-545.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta 36-545, service manual, brief instructions and user manuals Delta 36-545. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta 36-545.

Similar manuals

A complete manual for the device Delta 36-545, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta 36-545 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta 36-545.

A complete Delta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta 36-545 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta 36-545, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta 36-545, that we can find in the current document
3. Tips how to use the basic functions of the device Delta 36-545 - which should help us in our first steps of using Delta 36-545
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta 36-545
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta 36-545 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta 36-545?

Use the form below

If you did not solve your problem by using a manual Delta 36-545, ask a question using the form below. If a user had a similar problem with Delta 36-545 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)