English dropdown-ico

Manual LSI 22903

20 pages 1.29 mb
Download

Go to site of 20

Summary
  • LSI 22903 - page 1

    No vem ber 200 0 1 Cop yright © 2000 by LS I Logic Corporation. All rights reserved. ® LSI22902/229 03 Host Adapter to Intel ISP110 0 Internet Ser ver Quick Installation Guide The LSI Logic LSI229 02/2290 3 PCI to Dual Channe l Ultra2 SCSI Low Profil e Host Adapter is idea lly sui ted for install ation in to the I ntel ISP1 100 Inter net Ser v er ...

  • LSI 22903 - page 2

    2 LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r Figure 1 LSI22902 Host Adapter Kit 2 Install ation The instal latio n process contai ns the following four major se ctions: • Section 2.1, “ Setting u p the Installati on” • Section 2.2, “ Inst alling th e Host A dapter B oard” • Sect ion 2.3 , “Install ing N ew Driv ...

  • LSI 22903 - page 3

    LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 3 2.1 Setting up the I nstallation Impor tan t: Make sure the ISP1100 s er ver is tur ned off and is not plugged i nto an e lectri cal outl et. T ake all p recauti ons to minimize E SD . A groun d strap is re comme nded. Step 1 . Identify the par ts listed be low on the LSI22902/229 0 ...

  • LSI 22903 - page 4

    4 LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r Step 4. Lift the c ov er using the n otch in th e front of the cover and remo ve . Refe r to Figure 3 f or a phot ograph of the ISP 1100. Figure 3 In tel ISP1 100 Int ernet Ser ver Step 5 . Locate the component s of the ISP 1100. Refer to Fi gure 4 for a photograph of an opened unit ...

  • LSI 22903 - page 5

    LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 5 f . Slimli ne flop py and CD-ROM ass embly . g. T wo h ard dri ve ba ys. The ISP1 100 is provided with a fl opp y cable f or hard dr ives, but no drives are installe d or included . h. IDE ca ble with hard dr ive connector s. The cables are r outed under the d rive ba ys and the CD- ...

  • LSI 22903 - page 6

    6 LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r Refe r to Figure 5 . Step 2 . On the b ack of the ch assis, re mov e the two sc rews holding the ex pans ion bays retent ion bracket. Step 3. Remo ve t he ret en tion b ra ck et and t he e xpansion slot c o ve r . Figure 5 PCI Slot Location Y ou can use on e of two metho ds to ins t ...

  • LSI 22903 - page 7

    LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 7 Step 1 . Attach th e hard dr ive LED cable to th e SCSI hos t adapt er card . Use eithe r pin pai rs 1-2 or 3-4, a s shown in the inset in Figure 6 . Step 2 . With the h ost ad apter board brack et facing the rea r of the compu ter , inser t t he host ad apter car d in the expansio ...

  • LSI 22903 - page 8

    8 LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 2.2.2 L SI22902 I nstallation M ethod 2 Method 2 is different from the fir st met hod in that you remov e the ris er card fro m the ISP110 0 to inser t the LSI22902 /22903, rat her than doing it in pl ace as i n Metho d 1. Ref er to Figure 7 f or a pho tograph showing the host a dap ...

  • LSI 22903 - page 9

    LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 9 Figure 7 Method 2 Installation At this poi nt in the in stallati on pro cess, you should be a t the same p oint, regardles s of the insta llation me thod chose n. Procee d with the next step . Step 6. Remo v e the flo pp y driv e cab le as sho wn in Figure 8 by gentl y lifting the c ...

  • LSI 22903 - page 10

    10 LSI229 02/22903 Host Adap ter to Intel ISP1100 Internet Server Figure 8 Floppy Cab le Location ...

  • LSI 22903 - page 11

    LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 11 Figure 9 CD-ROM and Po wer Cables 2.3 Insta lling Ne w Drives This sec tion of the p roce dure descr ibes i nstalli ng the pro per SCSI h ard dri v es, as well as a CD -ROM dri v e and fl oppy drive , in th e ISP1100 . It also inc ludes rem oving the existing I DE hard dr ives ship ...

  • LSI 22903 - page 12

    12 LSI229 02/22903 Host Adap ter to Intel ISP1100 Internet Server Figure 10 CD-R OM/Floppy Assembl y Step 2. Remov e the two hard dri ve ba ys by lifting the b ack of the bay until the bay c lears the two snaptop stand offs and remove . Refe r to Figure 11 for a pho tograph of this step. Step 3. Mo unt the two L VD SCSI hard dri v es in the bays ac ...

  • LSI 22903 - page 13

    LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 13 Figure 11 Removing the Har d Drive Bays Note: Each device on the S CSI bus, in this c ase, the hos t adapter and hard dr ives, must ha ve a unique SCSI ID . SCSI ID 7 is the default host adapte r setting . See the d ocumentati on f or y our ha rd driv es fo r assi stanc e in det er ...

  • LSI 22903 - page 14

    14 LSI229 02/22903 Host Adap ter to Intel ISP1100 Internet Server Figure 12 Removing the IDE Cable Step 5 . Pull the Slim line flop p y cable up a nd lay it out of the way temporari ly . Step 6 . Attach th e preforme d 68-pin L VD SCSI cable to th e host adapter b oard. Step 7 . Route th e cable along th e sid e of the cha ssis u nder the fan assem ...

  • LSI 22903 - page 15

    LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 15 Figure 13 SCSI Cable Routing Step 9 . Install b oth dr ive ba ys by positioni ng the fro nt tabs in their respective positi ons with th e rear of the bay ov e r the cha ssis snapt op standoff s. Step 1 0. Fir mly pr ess down on the rear of th e bay until the ba y “snaps” secure ...

  • LSI 22903 - page 16

    16 LSI229 02/22903 Host Adap ter to Intel ISP1100 Internet Server Figure 14 Drive Bay Installation Step 12. Reinstal l the CD-ROM an d floppy drives. Use the three mou nting screws and atta ch the CD-ROM/floppy devices to the chas sis, taki ng care to no t ov er t ighten the mounting s crews. Over tignten ing cause war p in the ISP11 00 chas sis. S ...

  • LSI 22903 - page 17

    LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 17 Figure 15 CD-R OM and Floppy Installation 2.4 Completing the Inst allation Step 1. Attach t he loose e nd of the ha rd driv e LED cab le to the serve r board SC SI LED c onnector, J11. Refe r to Figure 16 on th e nex t page for a photograph showing the LED ca ble attachment. Step 2 ...

  • LSI 22903 - page 18

    18 LSI229 02/22903 Host Adap ter to Intel ISP1100 Internet Server Figure 16 Attaching the Har d Drive LED Activity C able ...

  • LSI 22903 - page 19

    LSI22902 /22903 Host Adap ter to Intel ISP1100 Internet Ser ve r 19 Notes ...

  • LSI 22903 - page 20

    To receive p roduct literatur e, visit us at h ttp://www.lsilogic.c om. LSI Logic Corporation reserves the right to make changes to any prod ucts and services herein a t any time w ithout notice. LSI Logic do es not assume an y responsibility or liability arising out of the app lication or use o f any product or service described herein, e xcept as ...

Manufacturer LSI Category Server

Documents that we receive from a manufacturer of a LSI 22903 can be divided into several groups. They are, among others:
- LSI technical drawings
- 22903 manuals
- LSI product data sheets
- information booklets
- or energy labels LSI 22903
All of them are important, but the most important information from the point of view of use of the device are in the user manual LSI 22903.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals LSI 22903, service manual, brief instructions and user manuals LSI 22903. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product LSI 22903.

Similar manuals

A complete manual for the device LSI 22903, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use LSI 22903 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of LSI 22903.

A complete LSI manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual LSI 22903 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the LSI 22903, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the LSI 22903, that we can find in the current document
3. Tips how to use the basic functions of the device LSI 22903 - which should help us in our first steps of using LSI 22903
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with LSI 22903
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of LSI 22903 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning LSI 22903?

Use the form below

If you did not solve your problem by using a manual LSI 22903, ask a question using the form below. If a user had a similar problem with LSI 22903 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)