English dropdown-ico

Manual Husqvarna Rider 15V2

55 pages 2.03 mb
Download

Go to site of 55

Summary
  • Husqvarna Rider 15V2 - page 1

    Oper a tor´s manual Rider 15V2 Please read these instructions car efully and make sur e you understand them bef ore using the machine. English ...

  • Husqvarna Rider 15V2 - page 2

    Svenska – 31 Sve-5 225/232/235 Bruk 97-11-25, 08.46 31 ...

  • Husqvarna Rider 15V2 - page 3

    English – 1 Operator ’ s Manual for Rider 15V2 CONTENTS Safety rules for USA ........................................... 2 Introduction ......................................................... 4 T ravel and transport on public roads ................ 4 T owing .............................................................. 4 Intended use ....... ...

  • Husqvarna Rider 15V2 - page 4

    2 – English These instructions are for your safety . Read them carefully . Safe operation practices for ride-on mowers IMPORT ANT! This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. 1. Safety rules f or USA I. General oper ...

  • Husqvarna Rider 15V2 - page 5

    English – 3 IV . Service 1. Use extra care in handling gasoline and other fuels. They are flammable and vapours are explosive. a) Use only an approved container . b) Never remove gas cap or add fuel with the engine running. Allow engine to cool before refuelling. Do not smoke. c) Never refuel the machine indoors. d) Never store the machine or fue ...

  • Husqvarna Rider 15V2 - page 6

    4 – English INTRODUCTION Dear customer Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a frontmounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency even in small or confined areas. Collected controls and a hydrostatic transmission controlled by pedal ...

  • Husqvarna Rider 15V2 - page 7

    English – 5 INTRODUCTION Good service Husqvarna products are sold all over the world and only through servicing dealers. This is to ensure that you, the customer, get the best support and service. When you need spare parts or advice on service issues, warranty terms, etc., contact: This Operator ’ s Manual belongs to machine with serial number: ...

  • Husqvarna Rider 15V2 - page 8

    6 – English EXPLANA TION OF SYMBOLS These symbols are on the machine and in the operator ’ s manual. Study them carefully so that you know what they mean. Read the operator ’ s manual Reverse Neutral Fast Slow Engine off Battery Choke Fuel Oil level Cutting height Backwards Forwards Ignition Hydrostatic free wheel Use hearing protection Parki ...

  • Husqvarna Rider 15V2 - page 9

    English – 7 8010-047 6003-002 8010-052 Safety instructions These instructions are for your safety . Read them carefully . General use • Read all the instructions in this operator ’ s manual and on the machine before you start it. Ensure you understand them and then observe them. • Learn how to use the machine and its controls safely and lea ...

  • Husqvarna Rider 15V2 - page 10

    8 – English 6003-006 8011-292 • T ake care when rounding a fixed object, so that the blades do not hit it. Never run the machine over foreign objects. • Only use the machine in daylight or in other well-lit conditions. Keep the machine at a safe distance from holes or other irregularities in the ground. Pay attention to other possible risks. ...

  • Husqvarna Rider 15V2 - page 11

    English – 9 8010-054 6003-004 Be especially car eful when driving on slopes. Mow upwar ds and downwards on slopes, not sideways. Driving on slopes Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is the greatest; this can result in serious injury or death. All slopes demand ...

  • Husqvarna Rider 15V2 - page 12

    10 – English 8010-057 8010-058 Children Serious accidents may occur if you fail to be on your guard for children in the vicinity of the machine. Children are often attracted to the machine and mowing. • Never assume that children will remain where you last saw them. • Keep children away from the area to be mowed and under close supervision by ...

  • Husqvarna Rider 15V2 - page 13

    English – 11 WARNING! The engine and the exhaust system become very hot during operation. Risk of burn injuries if touched. WARNING! The battery contains lead and lead pollutants, chemicals that are considered to cause cancer, birth defects or other reproductive impairment. Wash your hands after touching the battery. 6003-009 • If leaks arise i ...

  • Husqvarna Rider 15V2 - page 14

    12 – English 8009-467 8010-061 SAFETY INSTRUCTIONS • Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon monoxide, an odourless, poisonous and highly dangerous gas. • Stop and inspect the equipment if you run over or into anything. If necessary , make repairs before starting. • Never make adju ...

  • Husqvarna Rider 15V2 - page 15

    English – 13 Presentation Congratulations on your choice of a top quality product which you will enjoy for many years. These instructions describe the Rider 15V2. This rider mower is equipped with a 15 horsepower Kawasaki engine. PRESENT A TION Location of the controls 1. Ignition lock 2. Choke lever 3. Throttle lever 4. Adjustment of cutting hei ...

  • Husqvarna Rider 15V2 - page 16

    14 – English PRESENT A TION 1 2 2 1 WARNING! Make sure that branches do not obstruct the pedals when mowing under bushes, otherwise you may lose control. Parking brake The parking brake is applied as follows: 1. Press down the brake pedal. 2. Press in the lock button on the steering column. 3. Release up the brake pedal while holding the button p ...

  • Husqvarna Rider 15V2 - page 17

    English – 15 PRESENT A TION Cutting unit The Rider 15V2 can be fitted with three different cutting units. Side ejector - 970 mm/38" Combi - 1030 mm/41" Combi - 1 120 mm/44" See “ Maintenance Checking the Blades ” for identification of the cutting unit. The combi deck functions as a mulching deck when a bio-clip plug is mounte ...

  • Husqvarna Rider 15V2 - page 18

    16 – English PRESENT A TION Fuelling The engine should be run on 87 octane (or higher) unleaded petrol/gasoline (no oil added). For more information about methanol and ethanol fuels, see “ Technical Data ” . Do not fill the tank completely, leave an expansion area of at least 2.5 cm (1"). Seat The seat has a jointed attachment on the fro ...

  • Husqvarna Rider 15V2 - page 19

    English – 17 DRIVING Before starting • Read the safety instructions and information on the location and function of the controls before starting. • Conduct daily maintenance before starting (see “ Maintenance schedule ” . Starting the engine 1. Lift up the cutting unit by pulling the lever backwards to locked position (transport posi- tio ...

  • Husqvarna Rider 15V2 - page 20

    18 – English DRIVING 5. When the engine starts release the ignition key immediately back to neutral position. WARNING! Never run the engine indoors, in enclosed or poorly ventilated areas. The exhaust fumes contain toxic carbon monoxide. 6017-244 6017-245 6. Push the choke lever gradually forward when the engine has started. 7. Set the required e ...

  • Husqvarna Rider 15V2 - page 21

    English – 19 DRIVING Driving the machine 1. Release the parking brake by pressing down the brake pedal. 3 . Select the required cutting height (1-9) with the cutting height lever . T o obtain a uniform cutting height it is important that the tyre pressures are equal on both front wheels 60 kPa/8.5 PSI. 2 1 2. Carefully press down one of the pedal ...

  • Husqvarna Rider 15V2 - page 22

    20 – English Mowing pattern DRIVING 4. Push in the lock button on the lift lever and lower down the cutting unit. WARNING! Clear the lawn from stones and other object which can be thrown out by the blades. Cutting tips • Localise and mark stones and other fixed objects to avoid collision. • Start with a high cutting height and reduce down unt ...

  • Husqvarna Rider 15V2 - page 23

    English – 21 DRIVING MAX 15 WARNING! Never drive the machine on ground with a slope of more than 15 ° . Mow slopes upwards and downwards, never across. Avoid sudden changes in direction. Release lever The release control must be pulled out in order for the Rider to be moved when the engine is shutoff. 6007-002 6007-217H Stopping the engine Prefe ...

  • Husqvarna Rider 15V2 - page 24

    22 – English 50 100 MAINTENANCE W ARNING! No service procedures must be conducted on the engine or cutting unit unless: • The engine is switched off. • The ignition key is removed. • The ignition cable is removed from the plug. • The parking brake is applied. • The cutting unit is disengaged. Maintenance schedule The following maintenea ...

  • Husqvarna Rider 15V2 - page 25

    English – 23 Removing the machine hoods Engine hood The engine is accessible for servicing when the engine hood is lifted up. T ilt the seat forward, release the rubber strap under the seat, and tilt the hood backwards. MAINTENANCE Left-hand fender Release the screws in the fender (2) and lift off the fender . Right-hand fender Remove the knob (1 ...

  • Husqvarna Rider 15V2 - page 26

    24 – English Checking and adjustment of the steering wires The steering is controlled by means of wires. These can in time become slack, which implies that the adjustment of the steering becomes altered. Check and adjust the steering as follows: 1. Dismantle the frame-plate by releasing the screws (two on each side). MAINTENANCE Adjusting the bra ...

  • Husqvarna Rider 15V2 - page 27

    English – 25 MAINTENANCE Replacing the fuel filter Replace the pipe fitted fuel filter every 100 running hours (once per season) or more frequently if it is clogged. Replace the filter as follows: 1 . Fold open the engine cover . 2 . Move the hose clips away from the filter . Use a pair of flat pliers. 3 . Pull of f the filter from the hose ends. ...

  • Husqvarna Rider 15V2 - page 28

    26 – English Replacing the air filter MAINTENANCE 8009-446 8009-447 8009-448 8009-450 8009-452 VARNING! Exhaust system is hot. Allow to cool down. Risk of finger injuries. 2. Lift out the paper element and the foam element from the air cleaner case. 3. Clean the foam element by washing it in detergent and water. 4. Dry the foam element thorougly. ...

  • Husqvarna Rider 15V2 - page 29

    English – 27 W ARNING! Procedures on contact with acid External: Rinse well with plenty of water . Internal: Drink large quantities of water or milk. Contact a doctor as soon as possible. Eyes: Rinse well with plenty of water . Contact a doctor as soon as possible. Batteries emit explosive gas. Sparks, flames and cigarettes must absolutely not be ...

  • Husqvarna Rider 15V2 - page 30

    28 – English MAINTENANCE Inspecting the safety system The Rider is equipped with a safety system that prevents starting or driving under the following conditions: The engine should only be possible to start when the cutting unit is in its raised position and the hydrostat pedals are in the neutral position. The driver does not need to be seated i ...

  • Husqvarna Rider 15V2 - page 31

    English – 29 MAINTENANCE Checking the engine ’ s cooling air intake Clean the air intake grille in the engine cover behind the driver ’ s seat. Fold open the engine cover . Check that the cooling intake is free from leaves, grass and dirt. Check the air duct, located on the inside of the engine cover , ensure it is clean and does not rub agai ...

  • Husqvarna Rider 15V2 - page 32

    30 – English MAINTENANCE 1 2 3 Fitting the cutting unit 3. Insert the bolt and secure it with a locking pin. 6017-159 6017-120 WARNING! Observe caution to avoid trapping your hand. 8009-438 4. Press down the frame and insert the pin. Fit the drive belt around the drive wheels of the cutting unit. 5. Hook up the height adjustment strut. 6017-160 M ...

  • Husqvarna Rider 15V2 - page 33

    English – 31 6017-142 6. Move the support wheels to their parking position. 7. Fit the front cover . 8009-439 8009-440 8. Secure the collet spring. WARNING! Wear protective glasses when removing the cutting unit. The collet spring which tensions up the belt can go off and cause personal injury. Removing the cutting unit 2 3 1 6017-021 MAINTENANCE ...

  • Husqvarna Rider 15V2 - page 34

    32 – English MAINTENANCE Checking and adjusting the cutting unit ’ s ground pressure T o achieve the best cutting results the cutting unit should follow the underlying surface without pressing too hard against it. The pressure is adjusted with a screw on each side of the machine. 1. Check the air pressure in the tyres 60 kPa (0.6 kp/cm 2 /8.5 P ...

  • Husqvarna Rider 15V2 - page 35

    English – 33 MAINTENANCE Adjusting the parallelism of the cutting unit 1. Remove the front hood and right-hand fender. 2. Undo the nuts on the lift strut. 3. Screw out (extend) the stay to raise the rear edge of the cover. Screw in (shorten) the stay to lower the rear edge of the cover. 4. Tighten the nuts after adjustment. 5. On completion of th ...

  • Husqvarna Rider 15V2 - page 36

    34 – English MAINTENANCE Replacing the cutting unit belts Belt change on Combi 103 1. Remove the cutting unit. 2. Remove the front bolt from the parallel strut and tip the strut backwards. Push the height adjustment strut forwards. WARNING! Wear gloves to protect your hands when working with the blades. 6017-154 6017-161 8009-173 4. Useful hint: ...

  • Husqvarna Rider 15V2 - page 37

    English – 35 MAINTENANCE 5. Fit the protective cover over the belts and replace the parallelism arm. Belt change on cutting unit with side ejection and Combi 112 On these cutting units with “ collision-proof ” blades, the blades are driven by one V -belt. Do as follows to change the V -belt: 1. Remove the cutting unit. 2. Undo the bolt on the ...

  • Husqvarna Rider 15V2 - page 38

    36 – English MAINTENANCE Service position for the cutting unit The cutting head can be placed in the service position to provide easy access for cleaning, repairs and servicing. In the service position the cutting unit is raised and locked in the vertical position. Placing in service position 1. Position the machine on flat ground. Apply the park ...

  • Husqvarna Rider 15V2 - page 39

    English – 37 MAINTENANCE 4. Fit the support wheels on either side of the rear of the cutting unit. 5. Disengage the spring for the drive belt tensioning wheel. 6. Place a foot on the front edge of the cutting unit near the wheel and raise the front edge of the unit to make it easier to remove the lift strut. WARNING! Wear protective glasses when ...

  • Husqvarna Rider 15V2 - page 40

    38 – English MAINTENANCE Restoring from service position T o leave the service position, reverse the procedures set out in “ Placing in the service position ” . Make sure that the cutting unit ’ s “ lug ” (3) enters the loop correctly on the underside of the machine, see diagram. 2 1 8. Lift of f the drive belt (1). Then pull out the pi ...

  • Husqvarna Rider 15V2 - page 41

    English – 39 MAINTENANCE Checking the blades T o achieve the best mowing results it is important that the blades are undamaged and well-sharpened. Check that the blades ’ attachment screws are tight. IMPORTANT INFORMATION Replacing or sharpening the blades should be conducted by an authorised service workshop. IMPORTANT INFORMATION Combi unit 1 ...

  • Husqvarna Rider 15V2 - page 42

    40 – English MAINTENANCE Replacing the break-pin (Combi 103) The blades are fitted with a break-pin to protect the BioClip unit and its drive when colliding with obstacles. A domed, spring friction washer is fitted to each blade bolt. The washer must always be replaced with a new washer if the blade bolt is loosened. Otherwise the break-pin can b ...

  • Husqvarna Rider 15V2 - page 43

    English – 41 LUBRICA TION Checking the engine ’ s oil level Check the oil level in the engine when the Rider stands horizontal and the engine is switched off. Fold open the engine cover . Release the dip stick and pull out. Wipe off the oil and insert again without screwing it in. The dip stick must be fully screwed down. Pull out the dip stick ...

  • Husqvarna Rider 15V2 - page 44

    42 – English LUBRICA TION Changing the oil The oil should be changed for the first time after 8 hours of running time. Thereafter it should be changed every 100 hours of running time. With heavy loads or high temperatures replace the oil after every 50 hours. WARNING! Engine oil can be very hot if it is drained off directly after the engine is st ...

  • Husqvarna Rider 15V2 - page 45

    English – 43 LUBRICA TION Lubricating the belt adjuster The belt adjuster should be lubricated regularly using good quality molybdenum disulphide grease*. 1 nipple from the right-hand side under the engine ’ s lower belt pulley, until grease is forced out. With daily use lubrication should be conducted twice a week. General lubrication All join ...

  • Husqvarna Rider 15V2 - page 46

    44 – English Problem Procedure Engine will not start. • Fuel tank empty . • Spark plug defective. • Spark plug connection defective. • Dirt in carburettor or fuel pipe. • Starter does not pull round engine. Starter does not pull round engine. • Battery flat. • Bad contact between cable and battery terminal. • Lift lever for cuttin ...

  • Husqvarna Rider 15V2 - page 47

    English – 45 Winter storage At the end of the season the machine should immediately be put in order for storage, also if it is going to stand idle for more than 30 days. Fuel which is left to stand for long periods (30 days or more) can leave tacky deposits which can block the carburettor and interfere with the engine. Fuel stabiliser is an accep ...

  • Husqvarna Rider 15V2 - page 48

    46 – English Dimensions Rider 15V2 Length without cutting unit 2020 mm/6.61 ft Width without cutting unit 880 mm/2.89 ft Height 1060 mm/3.52 ft Weight 247-260 kg/543-572 lb including unit Wheel base 855 mm/2.8 ft T rack Front 715 mm/2.34 ft, rear 625 mm/2.05 ft T yre size 16 x 6.50 x 8 T yre pressure, front & rear 60 kPa (0.6 kp/cm 2 /8.5 PSI ...

  • Husqvarna Rider 15V2 - page 49

    English – 47 SER VICE JOURNAL Work done Pre-delivery service 1. Top up battery with acid and recharge for four hours. 2. Fit steering wheel, seat and any optional equipment. 3. Adjust cutting unit: Adjust the lifting springs (the “ weight ” of the cutting unit should be 12-15 kg/26,5-33 lbs). Only applies to Combi deck. Adjust cutting unit so ...

  • Husqvarna Rider 15V2 - page 50

    48 – English SER VICE JOURNAL Work done Date, mileage, stamp, sign ...

  • Husqvarna Rider 15V2 - page 51

    English – 49 SER VICE JOURNAL Work done Date, mileage, stamp, sign ...

  • Husqvarna Rider 15V2 - page 52

    50 – English SER VICE JOURNAL Work done Date, mileage, stamp, sign ...

  • Husqvarna Rider 15V2 - page 53

    SER VICE JOURNAL Work done Date, mileage, stamp, sign ´®z+H-•¶5O¨ ...

  • Husqvarna Rider 15V2 - page 54

    52 – English ...

  • Husqvarna Rider 15V2 - page 55

    114 01 39-95 2002W45 ´®z+H-•¶5O¨ ...

Manufacturer Husqvarna Category Lawn Mower

Documents that we receive from a manufacturer of a Husqvarna Rider 15V2 can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- Rider 15V2 manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna Rider 15V2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna Rider 15V2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna Rider 15V2, service manual, brief instructions and user manuals Husqvarna Rider 15V2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna Rider 15V2.

Similar manuals

A complete manual for the device Husqvarna Rider 15V2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna Rider 15V2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna Rider 15V2.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna Rider 15V2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna Rider 15V2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna Rider 15V2, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna Rider 15V2 - which should help us in our first steps of using Husqvarna Rider 15V2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna Rider 15V2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna Rider 15V2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna Rider 15V2?

Use the form below

If you did not solve your problem by using a manual Husqvarna Rider 15V2, ask a question using the form below. If a user had a similar problem with Husqvarna Rider 15V2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)