English dropdown-ico

Manual Profile CA200

20 pages 3.53 mb
Download

Go to site of 20

Summary
  • Profile CA200 - page 1

    CA200 CA400 CA600 CA800 CA1200 CA440 CA640 CA600M CA400M MOSFET POWER AMPLIFIERS Installation Instructions / Owner's Man ual ...

  • Profile CA200 - page 2

    1 ...

  • Profile CA200 - page 3

    I NTRODUCTION Congratulations on your purchase of a California state-of-the-art power amplifier. Your selection of a California car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an exi sting system or including your California amplifier in a new system, you are certain to notice immediate performance be ...

  • Profile CA200 - page 4

    S AFETY PRECAUTIONS Fuse amplifier’s power wire at the battery . Be sure to fuse the power wire within 12” of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the power amplifier not the car&ap ...

  • Profile CA200 - page 5

    F EATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Short Circuit Protection The circuit protects the amplifier from damage due to a short found in the ...

  • Profile CA200 - page 6

    Bass Boost For added low frequency performance the amplifiers are equipped with a variable 0~12 dB bass boost @ 45Hz. Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output. The amplifier will turn on and off with the ...

  • Profile CA200 - page 7

    Speaker Output R L Bridged REM GND B+ Fuse Connect the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box. We recommended using an 4 to 10 gauge power wire for your connections depending on the amplifier and length of the wire. Stri ...

  • Profile CA200 - page 8

    M OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in whic ...

  • Profile CA200 - page 9

    CH3 CH1 CH4 Bass Boost 0 12 X-over 40 500 85 Level Max POWER PROTECTION CA 640 CA 640 Filter Min Low Off Hi CH2 Level Min Max Filter Low Off Hi Bass Boost 0 12 X-over 40 500 85 CH3 CH1 CH4 Bass Boost 0 12 X-over 40 500 85 Level Max POWER PROTECTION CA 640 CA 640 Filter Min Low Off Hi CH2 Level Min Max Filter Low Off Hi Bass Boost 0 12 X-over 40 500 ...

  • Profile CA200 - page 10

    CA 200 CA 200 Bass Boost 12 85 Level Max X-over 40 500 0 Filter Low Off Hi PROTECTION POWER Input Left Right Min Hi-Level L- G R+ L+ R- CA 200 CA 200 Bass Boost 12 85 Level Max X-over 40 500 0 Filter Low Off Hi PROTECTION POWER Input Left Right Min Hi-Level L- G R+ L+ R- High Level inputs have been included to connect the amplifier to a radio witho ...

  • Profile CA200 - page 11

    Fuse Bridged CH1 CH3 CH2 CH4 REM GND B+ CH1 CH2 CH3 CH4 Bridged Speaker Output Make the speaker connections using speaker wire that is at least 14 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is conne ...

  • Profile CA200 - page 12

    Speaker Output R L Bridged REM GND B+ Fuse Fuse Bridged CH1 CH3 CH2 CH4 REM GND B+ CH1 CH2 CH3 CH4 Bridged Speaker Output + + - - + + - - 4 Ohm Speaker (Minimum) 4 Ohm Speaker (Minimum) 4 Ohm Speaker (Minimum) 4 Ohm Speaker (Minimum) + + - - 4 Ohm Speaker (Minimum) 4 Ohm Speaker (Minimum) TWO CHANNEL BRIDGED SPEAKER CONNECTIONS FOUR CHANNEL BRIDGED ...

  • Profile CA200 - page 13

    Speaker Output R L Bridged REM GND B+ Fuse CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier. S PEAKER CONNECTION ...

  • Profile CA200 - page 14

    Bass Boost 12 85 X -over 40 500 0 Filter Low Off Hi MIN MAX LEVEL Select your crossover type and frequency. . (Please note: If you intend to u se the amplifier in the Tri-mode configuration, it is necessary to set the crossover control to the “Off” setting in order to receive full range output) The California amplifiers are equipped with a buil ...

  • Profile CA200 - page 15

    T ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal pro ...

  • Profile CA200 - page 16

    S PECIFICATIONS CA200 CA400 CA600 Output Power @ 4 Ohm 2 x 130W RMS 2 x 65W RMS 2 x 90W Bridged RMS @ 4 Ohm 1 x 195W THD @ RMS Power <0.07% Frequency Response 20Hz ~ 30Khz Signal To Noise >102dB High Level Input Impedance 100 Ohms 100 Crossover Frequency (Variable) 40Hz ~ 500Hz Bass Boost @ 45Hz 0dB ~ 12dB Size (H x D x W) 2 x 200W 2 x 300W P ...

  • Profile CA200 - page 17

    CA640 Output Power @ 4 Ohm 4 x 150W RMS 4 x 75W RMS 4 x 125W Bridged RMS @ 4 Ohm 2 x 225W THD @ RMS Power <0.07% Frequency Response 20Hz ~ 30Khz Signal To Noise >102dB Crossover Frequency (Variable) 40Hz ~ 500Hz Bass Boost @ 45Hz 0dB ~ 12dB Size (H x D x W) CA440 4 x 120W Power @ 4 Ohm 4 x 60W Power @ 2 Ohm 4 x 90W 2 x 180W <0.07% 20Hz ~ 3 ...

  • Profile CA200 - page 18

    LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser. If this product is proven to be defective within this one year period, Profile will repair it when said product is returned, with a copy ...

  • Profile CA200 - page 19

    WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit. 4) Include a brief description of the problem or failure with the unit. 5 ...

  • Profile CA200 - page 20

    PROFILE CONSUMER ELECTRONICS, INC. 1 5060 SHOEMAKER AVE SANTA FE SPRINGS , CA 90 670 TEL: ( 562 ) 404 - 9393 FAX: ( 562 ) 404 - 9433 WWW.PROFILEUSA.COM By ...

Manufacturer Profile Category Stereo Amplifier

Documents that we receive from a manufacturer of a Profile CA200 can be divided into several groups. They are, among others:
- Profile technical drawings
- CA200 manuals
- Profile product data sheets
- information booklets
- or energy labels Profile CA200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Profile CA200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Profile CA200, service manual, brief instructions and user manuals Profile CA200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Profile CA200.

Similar manuals

A complete manual for the device Profile CA200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Profile CA200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Profile CA200.

A complete Profile manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Profile CA200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Profile CA200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Profile CA200, that we can find in the current document
3. Tips how to use the basic functions of the device Profile CA200 - which should help us in our first steps of using Profile CA200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Profile CA200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Profile CA200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Profile CA200?

Use the form below

If you did not solve your problem by using a manual Profile CA200, ask a question using the form below. If a user had a similar problem with Profile CA200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)