English dropdown-ico

Manual Woods Equipment M8200

46 pages 2.74 mb
Download

Go to site of 46

Summary
  • Woods Equipment M8200 - page 1

    PN-46018 (R ev. 3/15 /02) 1 1 1868 LOADER MO UNTING KIT Loaders 1020 1027 mounting to Kubot a T ractor Models M8200 M9000 Includes Va l v e K i t s 56037 56038 56042 Hose Kit s 40542 40547 46047 46018 ...

  • Woods Equipment M8200 - page 2

    ii Introduc tion (2/9/0 1) T O THE DEALER: Assemb ly and proper i nstallation of this p roduct is the re sponsibil ity of the WOODS dealer . Read manual instr uctions and safet y rules. Make su re all items on the Dealer ’s Pr e-Delivery and Deliver y Check L ists in the Operator ’s Manual are com pleted before r eleasing equip ment to the owne ...

  • Woods Equipment M8200 - page 3

    SAFETY 1 Loader M ounting Kit (9/1 1/0 0) INST ALLA TION  During inst allation, the tra ctor engine should be off, the ke y re moved and th e bra kes l ocked . D o not disconnect hy drauli c lines until attachments are removed or lowered to the ground and system pressure is rel eased by operating valve levers. Never operate any hydraul i c cylin ...

  • Woods Equipment M8200 - page 4

    2 SAFETY Loader M ounting Ki t (9/1 1/00) (Safety R ules co ntinued fr om prev ious p age)  Do not connect a low-pres sure hydraulic hose into a high-pres sure system—it will burst th e hose. Do not use a high-pressure hose in pla ce of a low- pressure hose—i t is possi ble to ruptu re the valv e.  Always wear relatively tight and belted ...

  • Woods Equipment M8200 - page 5

    SAFETY 3 Loader M ounting Kit (9/1 1/00)  Keep all persons away from operator cont rol area while p erforming adju stments, service, or maintenance.  Ti ghten all bolt s, nuts and screws to torque chart specification s. Check that all cotter pin s are inst alled secure ly to ensure equi pment i s in a sa fe condition before putting unit into ...

  • Woods Equipment M8200 - page 6

    4 SAFETY PN-46018 (Rev . 1 1/10/00) 11 9 1 2 3 6 5 7 4 Loader Mount (Left Side) Optional Loader Control V alv e 10 8 M O D E LN O . S E R I A LN O . MASS (KG) ID NO. OREGON, IL U.S.A. YR OF MFG. 4 - SERIAL NUMBER P LATE 2 - PN 56053 W ARNING Read and understand Operator ’s Manual before operating. (Replacement manuals are available from dealer or ...

  • Woods Equipment M8200 - page 7

    SAFETY 5 PN-460 18 (Rev . 1 1/10/00) W ARNING 56050-A CRUSHING HAZARD T o avoid injury or death: Do not walk or work un - derneath a raised loader . Lower loader to ground before leaving tractor seat. F ALLING HAZARD T o avoid injury or death: Do not work from or allow riders on loader or its attachments. W ARNING (Safety D ecals cont inued from pr ...

  • Woods Equipment M8200 - page 8

    6 Mount Installation PN-46018 (Rev . 3/15/02) LOADER MOUNT INST ALLA TION ■ Only use 1 1 1868 Loader Mounting Kit for mount- ing Woods 1 020/1027 loaders to Kubot a M8200 and M9000 tracto rs. Any other use or modification of this kit may r esult in seri ous injury or dea th.  Safety in structio ns are importan t! Read a ll attachment and power ...

  • Woods Equipment M8200 - page 9

    Mount Installation 7 PN-460 18 (3/15/02 ) LOADER MOUNT INST ALLA TION C ont’d Figure 3 1 1 1868 L oader Mou nting Kit Remove T ractor Connector T ube or Adapter Block Follow this proce dure only i f using #40547 or #46047 Ho se Kits. NOTE: It is easier to rem ove th e connec tor t ube or adapter b lock be fore installin g the rig ht moun t. 1. Re ...

  • Woods Equipment M8200 - page 10

    8 Mount Installation PN-46018 (Rev . 3/15/02) LOADER MOU NT INST ALLA TION Cont’d Install Crossme mber NOTE: Le ave a ll cap screws loos e until l oader mounts are c ompletel y installe d. 1. Install #460 00 cr ossmem ber t o the u ndersid e of the trac tor clu tch hous ing, u sing ca p sc rews an d hardened flat wa shers a s sho wn in Fi gure 4. ...

  • Woods Equipment M8200 - page 11

    Mount Installation 9 PN-460 18 (3/15/02 ) LOADER MOUNT INST ALLA TION C ont’d Install Front Mount Bracket 1. Install front mount br acket (3) to tractor steering housing, usin g cap screw s (17) and h ardened flat washers ( 1 1) as show n in Fig ure 6. 3. 1002896 Front moun t brack et 1 1. 57817 5/8 Harde ned fla t washer 17. 307425 M16 x 1.5 x 3 ...

  • Woods Equipment M8200 - page 12

    10 Mount Installation PN-46018 (Rev . 3/15/02) LOADER MOU NT INST ALLA TION Cont’d Install Grill Guard 1. Install grill g uard ou tside the left and right sid e rails as shown in Figu re 8. 5. 59628 Right sid e rail (no t show n) 6. 59631 Left side rail 1 1. 57817 5/8 Harde ned fla t washer 12. 230 5/8 Hex nut 13. 4548 5/8 NC x 1-3/4 Cap sc rew F ...

  • Woods Equipment M8200 - page 13

    Hydraulic Installation 1 1 PN-4601 8 (Rev . 3/15/02) CONTROL V AL VE & H OSE KIT INST ALLA TION ■ Keep hands and body away from pres surized lines. Use p aper or cardboard, not han ds or other body p art s to check for leaks. Wear safety goggles. Hydraulic fluid under pressure can ea sily penetrate skin and will c ause serious injury or deat ...

  • Woods Equipment M8200 - page 14

    12 Hydraulic Installation PN-46018 (Rev . 3/15/02) 1 #40542 Hos e Kit (For use with tractor remotes) NOTE: T o use th is hy drau lic c onnec tio n, th e trac tor must be equip ped with two hydr aulic lev ers and four tractor hy drau lic cou plers . Install Hose Clamp Bra cket & Ch anne l 1. Install #40 539 hose c lamp bracket to right load er m ...

  • Woods Equipment M8200 - page 15

    Hydraulic Installation 13 PN-4601 8 (Rev . 3/15/02) #40542 Hose Kit Cont’d Route Hoses & Install Hose Support 1. Route hydr au li c h os es al ong loa der m ount , und er right si de of fuel tank, and over th e rear axl e. Be su re to avoid conta ct with 3- point linkag e, brake p edals , and other movea ble trac tor com ponents. IMPORT ANT ? ...

  • Woods Equipment M8200 - page 16

    14 Hydraulic Installation PN-46018 (Rev . 3/15/02) #40542 Hose Kit Cont’d Connect Hoses to T ractor 1. Connect h ydraul ic hoses to trac tor hydrau lic co u- plers a s show n in Fi gure 14. 2. Refer to tracto r operato r ’s manual for operatin g the trac tor hydrau lic l evers. Figure 14 Hose Co nnect ions to Tractor Hydr auli c Coup ler s 1 1 ...

  • Woods Equipment M8200 - page 17

    Hydraulic Installation 15 PN-4601 8 (Rev . 3/15/02) 2 #56037 Control V alve & #40547 Hose K it (For use with loader joystick) General Des cription This h ydrauli c co nnecti on uses a si ngle lev er contr ol valve mou nted on the r ight loa der mount wit h a bracke t as show n in Fig ure 16. Figure 16 #56037 Cont rol V alve Installed (T ypical ...

  • Woods Equipment M8200 - page 18

    16 Hydraulic Installation PN-46018 (Rev . 3/15/02) #56037 V alve Kit & #40547 Hose Kit Cont’d Assemble Control V alve Kit 1. Inst all the cont r ol le ver: a) Threa d end of handle (9) in to valve . b) Align han dle so that end wi th longe r bend is pointing to ward the adapte r fittings . Make sur e bends are i n line wi th front an d rea r ...

  • Woods Equipment M8200 - page 19

    Hydraulic Installation 17 PN-4601 8 (Rev . 3/15/02) #56037 V alve Kit & #40547 Hose Kit Cont’d 2 4 15 2 2 3 4 4 7 7 IN OUT 8 10 11 12 5 TRAC TOR PART POW ER BEYOND CD5558C Assem ble #4054 7 Hose K it IMPORT ANT ■ If hydraulic lines are not connected as shown in the mount inst allation manual or tractor manual, the loader control valve may b ...

  • Woods Equipment M8200 - page 20

    18 Hydraulic Installation PN-46018 (Rev . 3/15/02) #56037 V alve Kit & #40547 Hose Kit Cont’d Inst all Fi ttings to T ractor Hydraulic Line Refer to Fi gure 17 an d Figur e 18. 1. If not don e dur ing install ation of right rear load er mount, rem ove the tr actor hydr aulic li ne conn ector tube or adapter block (if e quipped) as sho wn in F ...

  • Woods Equipment M8200 - page 21

    Hydraulic Installation 19 PN-4601 8 (Rev . 3/15/02) #56037 V alve Kit & #40547 Hose Kit Cont’d Inst all Hose Ret ainer & Line Support Bracke t 1. Remove the cap scre ws that hol d the trac tor fender to th e operator platf orm and in stall the h ose retainer . 2. Positio n the ho se retainer to k eep the hos es from touching the tracto r ...

  • Woods Equipment M8200 - page 22

    20 Hydraulic Installation PN-46018 (Rev . 3/15/02) #56037 V alve Kit & #40547 Hose Kit Cont’d T orque Hardware & Tighten Fittings 1. T o rque all har dwar e to specifi catio ns given bel ow . 2. Check to be sure all hy drauli c fitting s are tight. 2 TORQUE SPECIFICA TIONS Wrench Bolt Qty Size Required T orque 1/4 x 3/4 1 7/16” 10 lbs.- ...

  • Woods Equipment M8200 - page 23

    Hydraulic Installation 21 PN-4601 8 (Rev . 3/15/02) 3 #56038 Cable Control Kit & #46047 Hos e Kit (For cab tractors only) Inst all Control V alve (2-Spool #56038 or 3-Spool #56042) 1. Install valv e assemb ly to v alve g uard, usi ng three 3/8 x 1- 1/2 c arria ge bolts ( 1), 3 /8 lo ck wa shers (2), and hex n uts (3). 2. Install valve/g uard as ...

  • Woods Equipment M8200 - page 24

    22 Hydraulic Installation PN-46018 (Rev . 3/15/02) #56038 V alve Kit & #46047 Hose Kit Cont’d Connect Controller to Cables 1. Slide the r ubber co ntrol boot up out of the way . Orient the contr oller a s shown i n Figure 2 4. 2. Usi n g a vi ce, c lamp t he con tro ller loos ely . 3. Remove bo th cab le retainer bol ts. 4. Push the c ontro l ...

  • Woods Equipment M8200 - page 25

    Hydraulic Installation 23 PN-4601 8 (Rev . 3/15/02) #56038 V alve Kit & #46047 Hose Kit Cont’d Inst all Controller S tand Brac ket NOTE: Use #46 049 adap ter plate a nd har dware from #46047 Hos e Kit. 1. Locate the c ontrol c able acc ess hole u nder th e rubber floor ma t in the right front corne r of the tractor cab. 2. Insert thr ee carri ...

  • Woods Equipment M8200 - page 26

    24 Hydraulic Installation PN-46018 (Rev . 3/15/02) #56038 V alve Kit & #46047 Hose Kit Cont’d Inst all Controller S tand 1. Attach contr oll er stand to contr oller m ount bracke t, using four 3/ 8 x 1-1 /4 carria ge bol ts, 3/8 fla t washers, l ock was hers, and nuts. 2. Attach co ntroller to contro ller stand, us ing thre e 5/16 x 4-1/2 cap ...

  • Woods Equipment M8200 - page 27

    Hydraulic Installation 25 PN-4601 8 (Rev . 3/15/02) #56038 V alve Kit & #46047 Hose Kit Cont’d Att ach Control Cables to V alve 1. Thread ja m nut ( g) over threade d end of cabl e. 2. Slide re tain er (f) ove r cable. 3. Thread adjuster ( e) comp letel y over cable. 4. Thread ja m nut ( d) onto c able. 5. Thread cable adapter ( a) onto en d ...

  • Woods Equipment M8200 - page 28

    26 Hydraulic Installation PN-46018 (Rev . 3/15/02) #56038 V alve Kit & #46047 Hose Kit Cont’d 3 1 PYB 5 8 6 OUT 7 6 5 2 1 IN CD5618C-Var Figure 30 #46047 Hos e Kit PBY Connect Hydraulic Lines IMPORT ANT ■ If hyd raulic lines are n ot connected as sh own in he mount ing kit manual or t he tractor manual, the c ontrol valve my be dama ged. A ...

  • Woods Equipment M8200 - page 29

    Hydraulic Installation 27 PN-4601 8 (Rev . 3/15/02) #56038 V alve Kit & #46047 Hose Kit Cont’d Install IN & PBY Lines 1. If not don e dur ing install ation of right rear load er mount, rem ove the trac tor hydraul ic line c onnec tor tube or adapter block (if e quipped) as sho wn in Figur e 2, Page 7. NOTE: If 90-d egree e lbow inc ludes ...

  • Woods Equipment M8200 - page 30

    28 Hydraulic Installation PN-46018 (Rev . 3/15/02) #56038 V alve Kit & #46047 Hose Kit Cont’d Connect Loader Feedline Hoses 1. The Contr ol V alve Ki t contains hoses ass emble d with q uick coup lers. A ttach the hoses t o load er feed- lines. 2. Connect l oader fee dline hose s to c ontro l valv e hydraulic coup lers fol lowing the color sc ...

  • Woods Equipment M8200 - page 31

    Hydraulic Installation 29 PN-4601 8 (Rev . 3/15/02) #56038 V alve Kit & #46047 Hose Kit Cont’d V erification of Control Movement s 1. Refer to the Woods Loa der Operator ’s Manual to complete the loade r instal lation . At leas t 6” spac ing should be mai ntain ed between v alve, bracket, or hoses an d any tractor control (brake pe dals, ...

  • Woods Equipment M8200 - page 32

    30 Hydraulic Installation PN-46018 (Rev . 3/15/02) NOTES ...

  • Woods Equipment M8200 - page 33

    PA R T S 3 1 PN-46018 (R ev . 1 1/10/00) Loaders 255 260 Loaders 255 260 Loaders 1020 1027 P ARTS INDEX 1 1 1868 LOADER MOUNTING KIT #1 1 1868 LOA DER MOUNT KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 #40542 H OSE K IT (For use with tractor remotes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 #56037 C O ...

  • Woods Equipment M8200 - page 34

    32 P AR TS PN-46018 (Rev . 1 1/10/00) 1 1 1868 LOADER M OUNTING KIT 1 3 1 2 1 1 8 1 2 3 4 5 6 1 1 1 1 9 11 1 2 1 2 1 3 1 3 1 4 12 1 16 2 2 2 2 1 1 1 7 1 8 2 0 7 7 2 3 CD5612C R E F P ART QTY DESCRIPTI ON 1 44490 1 Right rear mo unt 2 44491 1 Left rear mount 3 1002896 1 Front mount bra cket 4 46000 1 Crossme mber 5 59628 1 Right side rail 6 59631 1 ...

  • Woods Equipment M8200 - page 35

    PA R T S 3 3 PN-46018 (R ev . 1 1/10/00) #4054 2 HO SE KI T (FOR USE WITH TRACTOR REMOTE CONTROL LEVER) $ % & ' 5+ /2$'(5 %220 $   %8&.(7 &</ %$6( (1' '803 %   %8&.(7 &</ 52' (1' 52//%$&. &   %220 &</ 52' (1' '2:1 &apos ...

  • Woods Equipment M8200 - page 36

    34 P AR TS PN-46018 (Rev . 1 1/10/00) 56037 CO NTROL V AL VE 39 40 41 42 43 36 37 35 8 31 17 21-26 16 19 15 12 12 18(1) 18(2) 34 33 1 3 28 4 9 38 10 11 38 2 16 24 32 33 34 30 CD5736v ar-1 (Rev . 3/15/02) ...

  • Woods Equipment M8200 - page 37

    PA R T S 3 5 PN-46018 (R ev . 1 1/10/00) 56037 C ONTROL V AL VE P ARTS LIST REF P ART QTY DESCRIPTION 1 562 51 1 2-Spool val ve with co ntro lle r 2 450 56 1 2-Spool val ve mount 3 463 05 1 Boot bracke t 4 405 27 1 Rubber contro l boot (2-s pool) 8 463 40 1 V alve mounti ng plat e 9 562 54 1 Bent handle, 0.5 O D x 1 1.31 10 45003 1 Knob, 1.88 di am ...

  • Woods Equipment M8200 - page 38

    36 P AR TS PN-46018 (Rev . 1 1/10/00) 11 h 3 43 31 4 1 32 33 34 37 35 41 40 39 39 40 41 9 14 15 23 16 20(2) 22 24 16 13 22 23 21 24 12 21 19 18 20(1) 17 41 40 7 42 36 38 8 6 10 2 a b c d e f g CD5737 CABLE CONTROL V AL VE P ARTS #56038 - 2 Spool V alve #56042 - 3 Spool V alve ...

  • Woods Equipment M8200 - page 39

    PA R T S 3 7 PN-46018 (R ev . 1 1/10/00) CABLE CONTROL V AL VE P A RTS LIST #56038 - 2 SPOOL V ALVE #56042 - 3 SPOOL V ALVE R E F P ART QTY REF 1 562 14 1 Controller st and 2 562 15 1 Controller mo unt brack et 3 488 010 1 Dual axis cont r oll er 4 48801 1 1 Single axis c ontroller ( 56042) 6 460 45 1 V alve guard 7 562 50 1 Husco 2-spo ol va lve ( ...

  • Woods Equipment M8200 - page 40

    38 P AR TS PN-46018 (Rev . 1 1/10/00) #460 47 HO SE KI T (TO BE USED WITH CABLE-OPERATED CONTROLS) NOTE : Ki t contains fitti ngs that a re not needed for the M8200 or M9 000 trac tor . 10 11 12 13 1 4 15 16 17 18 19 1 PYB 5 8 6 IN OUT 7 6 5 9 2 1 CD5618C R E F P ART Q TY DESCRIPTION 1 4604 6 2 1/2 X 38” Hose without sleeve, 3/4 JIC F x 3/4 J ICF ...

  • Woods Equipment M8200 - page 41

    PA R T S 3 9 PN-46018 (R ev . 1 1/10/00) #4054 7 HO SE KI T (FOR USE WITH LOADER -MOUNTED CONTROL LEVER) 14 15 2 2 3 4 4 7 7 IN OUT 8 9 10 11 12 13 5 TRACTOR PART POWER BEYOND CD5558C R E F P ART QTY DESCRIPTION 2 315038 2 Adapter , 1/2 NPT F x 3/4 JICM 3 315058 1 Adapter , 1/2 NPT M x 3/ 4 JICF 4 40549 2 90° Elbow , 1/2 NP TM x M 26 x 1.5M (disca ...

  • Woods Equipment M8200 - page 42

    40 APPENDIX Bolt T orque & Size Chart s (Rev . 2/5/02) BOLT T ORQUE C HART Always tighten hardwar e to the se value s unl ess a di fferent tor que va lue or ti ghteni ng proc edure is listed f or a s pecific applica tio n. Fastene rs must al ways be r eplaced with th e same gr ade as s pecified in the manual parts l ist. Always us e the prop er ...

  • Woods Equipment M8200 - page 43

    APPENDIX 41 Bolt T orque & Size Chart s (Rev . 9/5/00) BOLT SIZE CHART NOTE: Chart show s bolt thread s izes an d corre sponding head ( wren ch) sizes for sta ndard SA E and metri c bolts . ABBREVIATIONS AG ..... .................... ............ ............. .......... A griculture A TF ........... ............. ......Auto matic Transmission ...

  • Woods Equipment M8200 - page 44

    F-8494 3/1/2000 (Rev . 1/1/2002) Woods Equipme nt Company 2606 I llinois Route 2 S outh Post Offi ce B ox 10 0 0 Oregon, I llinoi s 610 61 815-732-21 41 tel 815-732-75 80 fax W ARRANTY (Replacement Parts For All Models Except Mow’n Machines) WEC Company , d/b/a W oods Equipment Company (“WOODS”), warrants this product to b e free from defect ...

  • Woods Equipment M8200 - page 45

    F-3079 Effective 3/2/2000 (Rev ised 3/1/01) Woods Equipme nt Company 2606 Ill inois Route 2 South Post Office Box 10 00 Oregon, Ill ino is 61061 815-732-2 141 tel 815-732-7 580 fax W ARRANTY (All Mo dels E xc ept M ow’n Mach i nes) Please Enter Information Below an d Save For Futu re Reference. Date Pu rchase d: ___ _______ ____ _____ ____ ___ F ...

  • Woods Equipment M8200 - page 46

    Woods Eq uipment Comp any 2606 I lli noi s Ro ute 2 S out h Post Offic e Box 1000 Oregon, Illino is 61061 815-732- 2141 te l 815-732- 7580 fa x MANUAL P ART NUMBER 46018 © 1999 W oods Equipmen t Compa ny . All right s reserve d. ...

Manufacturer Woods Equipment Category Lawn Mower

Documents that we receive from a manufacturer of a Woods Equipment M8200 can be divided into several groups. They are, among others:
- Woods Equipment technical drawings
- M8200 manuals
- Woods Equipment product data sheets
- information booklets
- or energy labels Woods Equipment M8200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Woods Equipment M8200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Woods Equipment M8200, service manual, brief instructions and user manuals Woods Equipment M8200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Woods Equipment M8200.

Similar manuals

A complete manual for the device Woods Equipment M8200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Woods Equipment M8200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Woods Equipment M8200.

A complete Woods Equipment manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Woods Equipment M8200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Woods Equipment M8200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Woods Equipment M8200, that we can find in the current document
3. Tips how to use the basic functions of the device Woods Equipment M8200 - which should help us in our first steps of using Woods Equipment M8200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Woods Equipment M8200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Woods Equipment M8200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Woods Equipment M8200?

Use the form below

If you did not solve your problem by using a manual Woods Equipment M8200, ask a question using the form below. If a user had a similar problem with Woods Equipment M8200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)