English dropdown-ico

Manual Quatech SSP-100

51 pages 1.6 mb
Download

Go to site of 51

Summary
  • Quatech SSP-100 - page 1

    SSP-100 Single Channel RS-232 PCMCIA Asynchronous Adapter for PCMCIA Card Standard compatible machines User's Manual QUATECH, INC. TEL: (330) 434-3154 662 Wolf Ledges Parkway FAX: (330) 434-1409 Akron, Ohio 44311 BBS: (330) 434-2481 INTERFACE CARDS FOR IBM PC/AT AND PS/2 ...

  • Quatech SSP-100 - page 2

    ...

  • Quatech SSP-100 - page 3

    SSP-100 User's Manual i ...

  • Quatech SSP-100 - page 4

    Warranty Information Quatech Inc. warrants the S SP-100 to be free of defects for five ( 5 ) year s from the date of purchase. Quatech Inc. will repair or replace any adapter that fails to perform under normal operating conditions and in accordance with the procedures outlined in this document during the warranty period. Any damage that results fro ...

  • Quatech SSP-100 - page 5

    Declaration of Conformity Manufacturer's Name: Quatech, Inc. M anufacturer's Address: 662 Wolf Ledges Parkway Akron, OH 44311 (USA) Application of Council Directive: 89/336/EEC Standards to which Conformity is Declared: * EN50081-1 (EN55022) * EN50082-1 (IEC 801-2, IEC 801-3, & IEC 801-4) Type of Equipment: Information Technology Equi ...

  • Quatech SSP-100 - page 6

    Table of Contents 6-1 7 . Specifications ...................................................... 5-1 6 . External Connections ............................................. 4-8 5.2 Monitoring The Status Of PCMCIA Cards ............................... 4-7 5.1.3 Advanced Configuration Topics .................................. 4-5 5.1.2 Configuring With ...

  • Quatech SSP-100 - page 7

    SSP-200/300 User's Manual 5 ...

  • Quatech SSP-100 - page 8

    1 . Introduction The SSP-100 is a single channel RS- 232 asynchronous serial adapter for systems equipped with PCMCIA Type II and/or Type III expansion sockets. The SSP-100 is a PCMCIA Type II (5 mm) card and is PCMCIA PC Card Standard Specification 2.1 compliant. PCMCIA Card Cable Assembly Standard D-9 Male Figure 1. SSP-100 Card and Cable Assembl ...

  • Quatech SSP-100 - page 9

    (This page intentionally left blank.) SSP-100 User's Manual 1-2 ...

  • Quatech SSP-100 - page 10

    2 . DOS / Windows 3.x Installation Two configuration software programs are provided with the SSP-100 : a Client Driver, and a card Enabler. Both of these programs are executed from DOS (before entering Windows) and allow operation of the SSP-100 in both the DOS and Windows 3.x environments. For optimal operation, however, the Client Driver is the p ...

  • Quatech SSP-100 - page 11

    2 . 1 SSP-100 Client Driver for DOS In order to use the SSP-100 Client Driver, the system must be configured with Card and Socket Services software. Card and Socket Services software is not provided with the SSP-100 but is available from Quatech . IMPORTANT: Some versions of Card and Socket Services dated before 1993 do not support general purpose ...

  • Quatech SSP-100 - page 12

    version of Card and Socket Services must be installed on the system or the SSP-100 Enabler program must be used to configure the adapter. If the Client Driver reports the desired adapter configuration, the installation process is complete and the SSP-100 may be removed and/ or inserted from the system as desired. On each insertion into the PCMCIA s ...

  • Quatech SSP-100 - page 13

    option. If no number is specified, the SSP-100 will be configured as the next available COM Port using the standard base address and IRQ settings for that COM port. If this option is omitted, the user must either specify a base address or IRQ setting for the SSP-100 or allow Card and Socket Services to select a base address and IRQ to configure the ...

  • Quatech SSP-100 - page 14

    DEVICE = C: SSP-100 SSP100CL.SYS (b300,i5) (i10) ( ) In example 5, three command line arguments are provided. The Client Driver will first attempt to configure a SSP-100 inserted into any socket with a base address of 300H and IRQ 5. The BIOS equipment list will not be updated. If address 300H or IRQ 5 is unavailable, the Client Driver will proc ...

  • Quatech SSP-100 - page 15

    2.1.2.7 Example 7 DEVICE = C: SSP-100 SSP100CL.SYS (s0,b300,i5) (s1,b340,i10) The type of configuration shown in example 7 may be desirable in systems where more than one SSP-100 is to be installed. In this example, the Client Driver will attempt to configure a SSP-100 inserted into socket 0 with a base address of 300H and IRQ 5. If the SSP-100 ...

  • Quatech SSP-100 - page 16

    2 . 1 . 3 Common Problems Generic Client Drivers: Many Card and Socket Services packages include a generic client driver (or SuperClient) which configures standard I/O devices. If one of these generic client drivers is installed, it may configure the SSP-100 causing the SSP-100 client driver to fail installation. In these cases, the user should do ...

  • Quatech SSP-100 - page 17

    2 . 2 SSP-100 Enabler for DOS For systems that are not operating PCMCIA Card and Socket Services software, the SSP-100 DOS Enabler may be used to enable and configure the adapter. This Enabler, SSP100EN , will operate on any DOS system using an Intel 82365SL or PCIC compatible PCMCIA host adapter including the Cirrus Logic CL-PD6710 / 6720, the VLS ...

  • Quatech SSP-100 - page 18

    2 . 2 . 1 Command Line Options To configure a SSP-100 in the system, the Enabler requires one command line argument from the user to determine the configuration of the card. This argument must be enclosed in parenthes e s and within the argument, any or all of the following parameters may be specified using a comma (no spaces) to separate each para ...

  • Quatech SSP-100 - page 19

    Before removing a SSP-100 from its PCMCIA socket, the Enabler should be executed to free the system resources allocated when the card was installed. For this operation the Enabler provides on additional command line option: R instructs the enabler to release the resources previously allocated to the SSP-100 . When the 'R' option is used, ...

  • Quatech SSP-100 - page 20

    2.2.1.4 Example 4 SSP100EN (s0,b300,i3,wd8) In example 4, the Enabler will configure the SSP-100 in socket 0 with a base address of 300H and IRQ 3 using a configuration memory window at segment D800. 2.2.1.5 Example 5 SSP100EN (i 5 ,b340 , s1) In example 2, the Enabler will configure the SSP-100 in socket 1 with a base address of 340H and IRQ 5 usi ...

  • Quatech SSP-100 - page 21

    SSP100EN (s0,a3) In Example 9, the Client Driver will attempt to configure an SSP-100 into socket 0 with the COM 3 standard address of 3E8H and IRQ 4. The COM 3 spot of the BIOS equipment list will be updated automatically. If the requested socket is unavailable, or the COM 3 resource settings are unavailable, the SSP-100 will not be configured and ...

  • Quatech SSP-100 - page 22

    2 . 2 . 2 Common Problems Memory Range Exclusion: The Enabler requires a region of high DOS memory when configuring a SSP-100 . This region is 1000H bytes (4KB) long and by default begins at address D0000H (the default address may be changed using the "W" option). If a memory manager such as EMM386, QEMM, or 386Max is installed on the sys ...

  • Quatech SSP-100 - page 23

    (This Page Left Intentionally Blank) SSP-100 User’s Manual 2-14 ...

  • Quatech SSP-100 - page 24

    3 . Windows 95 , 98, 2000, ME, NT Installation To allow easy configuration of the SSP-100 , a Windows "INF" configuration file has been written for the hardware. 3 . 1 Installing a SSP-100 Under Windows 95, 98, ME, 2000 . 1. Insert the SSP-100 into any available PC Card socket. 2. The first time a new PC Card type is installed the New Har ...

  • Quatech SSP-100 - page 25

    4. The New Hardware Found window provides several options to configure the SSP-100 card. Insert the CD with the Windows Configuration file, select “CD-ROM drive” and path, and click " Next ". Windows will browse the path for the necessary files. SSP-100 User’s Manual 3-2 ...

  • Quatech SSP-100 - page 26

    Figure 5 . Windows 95, 98, ME Add New Hardware Wizard 5. During the installation process, it may be required to supply the computer Figure 6 . Windows 2000 New Hardware Wizar d SSP-100 User’s Manual 3-3 ...

  • Quatech SSP-100 - page 27

    with the Windows CD or installation diskettes. The SSP-100 's serial devices will require the file "SERIALUI.DLL". Insert the CD or diskette and click "OK". IMPORTANT NOTE: If the user already has these files installed on the computer, or if the installation disks are unavailable, it may not be necessary to supply the compu ...

  • Quatech SSP-100 - page 28

    4. Open the Properties dialog for the SSP-100 device, then click the Resources tab to view the Input/Output Range and Interrupt Request resource allocations. 5. Use the COM Port device names (COM2, COM4, etc.) to access any of the particular serial ports on the SSP-100 . This name is required by a Windows application when accessing a particular por ...

  • Quatech SSP-100 - page 29

    Figure 8 . Windows 2000 Device Manager 3 . 2 . 2 Changing Resource Settings with Windows 95, 98, ME Device Manager 1. Start the Windows Device Manager . 2. Double click on the hardware class Ports (Com and LPT) to list hardware devices in the class. 3. The SSP-100 belongs to this hardware class. The device name for the SSP-100 is : Quatech SSP-100 ...

  • Quatech SSP-100 - page 30

    3 . 2 . 3 Changing Resource Setting with Window 2000 Device Manager 1. Start the Windows Device Manager . 2. Double click on the hardware class Ports (Com and LPT) to list hardware devices in the class. 3. The SSP-100 belongs to this hardware class. The device name for the SSP-100 is : Quatech PCMCIA Serial Port. 4. Open the Properties dialog for t ...

  • Quatech SSP-100 - page 31

    Figure 9 . Windows 95,98,ME Resource Allocation SSP-100 User’s Manual 3-8 ...

  • Quatech SSP-100 - page 32

    Figure 10 . Windows 2000 Resource Allocation 5. Several predefined Basic Configurations have been included for the SSP-100 . The SSP-100 can either be forced to use a “standard” base address for COM1 - COM4, or it may be configured to allow Windows to assign the base address. Standard base I/O addresses are defined only for the first four logic ...

  • Quatech SSP-100 - page 33

    6. Select a Basic Configuration that displays "No conflicts" in the bottom display region titled Conflicting Device List from the drop down list. Some applications may not be able to access ports higher than COM4. To use the SSP-100 PCMCIA serial ports with these applications you might be forced to remove other serial communications devic ...

  • Quatech SSP-100 - page 34

    3 . 3 Common Problems Basic Configuration List Not Available: A problem noted on some systems is after a basic configuration has been manually selected is the basic configurations list for the SSP-100 is no longer available. The solution to this problem is to check the “Use Automatic Settings” box and allow Windows to reconfigure the SSP-100 ca ...

  • Quatech SSP-100 - page 35

    3 . 4 Installing SSP-100 under Windows NT To allow easy configuration of the DSP-100 the Quatech Device Manager for Windows NT has been written for the hardware. This configuration util i ty supports the DSP-100 only in block addressing mode. To begin the installation, open Windows Explorer and search for the ‘ Setup.exe ’ command to install th ...

  • Quatech SSP-100 - page 36

    1. Locate and double click the Quatech Device Manager icon on the desktop Device Manager Icon on Desktop SSP-100 User’s Manual 3-13 ...

  • Quatech SSP-100 - page 37

    2. Click the ‘ Add ’ button at the bottom of the Quatech Device Manager Window. 3. Follow the steps for the ‘ Add Quatech Hardware Wizard ’ . SSP-100 User’s Manual 3-14 ...

  • Quatech SSP-100 - page 38

    4. Complete the fin al steps of the installation, insert the PCMCIA Card and reboot the computer. v Additional help is available online The PCMCIA PC Card should now be configured. In the future, Windows NT will automatically recognize and configure the DSP-100. Note: Windows NT does not support ‘ Plug and Play ’ for PCMCIA cards. The PCMCIA Ca ...

  • Quatech SSP-100 - page 39

    4. Windows CE The Quatech PCMCIA Windows CD installat ion copies a multiple device-specifi c .cab files and the ini file to your desktop computer and launches the Application Manger (which resides on the user's desktop computer as a result of installing Active Syn c) with the Application Manager .ini file as a parameter. This in turn will inst ...

  • Quatech SSP-100 - page 40

    3. The setup program will copy the files to predetermined location, which can be changed by the user. Click next to proceed.. Installation is now complete. In the event that installation process took place with out having the Windows CE device connected to the computer and the install program will prompt the user that on the next on the next connec ...

  • Quatech SSP-100 - page 41

    SSP-100 User's Manual 4-3 ...

  • Quatech SSP-100 - page 42

    5 OS/2 Installation In order to use the SSP-100 Client Driver for OS/2, the system must be configured as follows: 1. The system must be running OS/2 version 2.1 or later. 2. OS/2 PCMCIA Card and Socket Services support must be installed. If PCMCIA support was not selected when OS/2 was installed, it can be added using the Selective Install facility ...

  • Quatech SSP-100 - page 43

    5 . 1 Command Line Options The SSP-100 Client Driver for OS/2 supports two methods of configuration: using "system assigned" resources and using "user assigned" resources. Both options provide full PCMCIA compliance and functionality (including "Hot-swapping") but each has some advantages and disadvantages as discussed ...

  • Quatech SSP-100 - page 44

    problem if DOS and/or Windows applications will be accessing the serial ports. This is because most DOS applications write directly to the communications hardware and the Windows Control Panel also wants to know the hardware configuration of the serial ports. For this reason, the SSP-100 Client Driver allows the user to request specific hardware se ...

  • Quatech SSP-100 - page 45

    5.1.2.2 Example 2 DEVICE=C: SSP-100 SSP 1 00.SYS (7,120,15) (3,300,4) In example 2, the Client Driver will attempt to configure the SSP-100 as COM3 using I/O address 300-3 07 hex and IRQ 4. If COM3 already exists, or if the I/O address or IRQ resources are already in use, the Client Driver will attempt to configure the SSP-100 as COM7 using I/O a ...

  • Quatech SSP-100 - page 46

    5 . 2 Monitoring The Status Of PCMCIA Cards OS/2 Warp provides a utility called "Plug and Play for PCMCIA" that can be used to monitor the status of each PCMCIA socket. In OS/2 version 2.1, this utility is called "Configuration Manager". When a SSP-100 is inserted, the Card Type for the appropriate socket will display " Ser ...

  • Quatech SSP-100 - page 47

    (This Page Left Intentionally Blank) SSP-100 User's Manual 4-9 ...

  • Quatech SSP-100 - page 48

    6. External Connections An adapter cable is included with the SSP-100 to convert the 9-pin PCMCIA output connector into a standard D-9 female connector, data terminal equipment (DTE) , as shown in the figures below. Standard D-9 (Female) Figure 12. SSP-100 Adapter Cable. D-9 Female Connector 1 2 3 4 5 9 8 7 6 RI CTS RTS DSR GND DTR DATA OUT CD DATA ...

  • Quatech SSP-100 - page 49

    (This page intentionally left blank.) SSP-100 User’s Manual 5-2 ...

  • Quatech SSP-100 - page 50

    7 . Specifications Bus Interface PCMCIA PC Card Standard 2.1 compliant Physical Dimensions Type II PCMCIA card (5mm) Maximum Baud Rate 120K Power Requirements +5 volts 1 8.85 mA (typical) 25.95 mA (maximum) Connector Adapter to standard female D-9 SSP-100 User's Manual 6-1 ...

  • Quatech SSP-100 - page 51

    SSP-100 User's Manual Revision 2.30 September, 2001 P/N 940-007 4 - 230 ...

Manufacturer Quatech Category Network Card

Documents that we receive from a manufacturer of a Quatech SSP-100 can be divided into several groups. They are, among others:
- Quatech technical drawings
- SSP-100 manuals
- Quatech product data sheets
- information booklets
- or energy labels Quatech SSP-100
All of them are important, but the most important information from the point of view of use of the device are in the user manual Quatech SSP-100.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Quatech SSP-100, service manual, brief instructions and user manuals Quatech SSP-100. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Quatech SSP-100.

Similar manuals

A complete manual for the device Quatech SSP-100, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Quatech SSP-100 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Quatech SSP-100.

A complete Quatech manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Quatech SSP-100 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Quatech SSP-100, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Quatech SSP-100, that we can find in the current document
3. Tips how to use the basic functions of the device Quatech SSP-100 - which should help us in our first steps of using Quatech SSP-100
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Quatech SSP-100
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Quatech SSP-100 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Quatech SSP-100?

Use the form below

If you did not solve your problem by using a manual Quatech SSP-100, ask a question using the form below. If a user had a similar problem with Quatech SSP-100 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)