English dropdown-ico

Manual Tanaka TBC-2251

20 pages 1.12 mb
Download

Go to site of 20

Summary
  • Tanaka TBC-2251 - page 1

    Owner’ Owner’ Owner’ Owner’ Owner’ s Man s Man s Man s Man s Man ual ual ual ual ual Model Numbers: TBC-2211, TBC-2251,TBC-230/B TBC-2211, TBC-2251,TBC-230/B TBC-2211, TBC-2251,TBC-230/B TBC-2211, TBC-2251,TBC-230/B TBC-2211, TBC-2251,TBC-230/B TRIMMERS/BR TRIMMERS/BR TRIMMERS/BR TRIMMERS/BR TRIMMERS/BR USHCUTTERS USHCUTTERS USHCUTTERS US ...

  • Tanaka TBC-2251 - page 2

    www.tanaka-usa.com 1 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Before using this unit: • Read the operator’s manual carefully. • Check that the cutt ing equipment is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment. See “Maintenance”. WARNING Read, understand and follow all ...

  • Tanaka TBC-2251 - page 3

    www.tanaka-usa.com 2 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Blade thrust may occur when the spinning blade contacts a solid object in the critical area. A dangerous reacti on may occur causing the entire unit and operator to be thrust violently. This reac tion is called BLADE THRUST. As a result, the operator may lose c ...

  • Tanaka TBC-2251 - page 4

    www.tanaka-usa.com 3 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 1. What is What? Since this manual covers several models, there m a y be some difference between pictures and your unit. Use the instructions that apply to your unit. 1. Fuel Cap 2. Throttle trigger 3. Starter handle 4. Blade Guard 5. Cutting attachment 6. Dri ...

  • Tanaka TBC-2251 - page 5

    www.tanaka-usa.com 4 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 2. Warnings and safety instructions. Operator Safety • Always wear a safet y face shield or goggles . • Always wear heavy, long pant s, boo ts and gloves. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair so it is above s ...

  • Tanaka TBC-2251 - page 6

    www.tanaka-usa.com 5 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 3. Assembly procedures Drive shaft to engine (Fig. 1 -1) Loosen tube locking bolt (1) about ten turns so that the bo lt tip will not obstruct drive sh aft tube to be inserted. When inserting drive sh aft tube, hold the tube locking bolt outward preventing insi ...

  • Tanaka TBC-2251 - page 7

    www.tanaka-usa.com 6 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Throttle wire/stop cord Remove the air cleaner cover. (Fig. 1-4) Connect stop cords. (Fig. 1 -5) Set outer receiver (1) (if so provided) into wire guide and put throttle wire through the outer receiver. (Fig. 1 -4) Connect throttle wire end to carburetor. (Fig ...

  • Tanaka TBC-2251 - page 8

    www.tanaka-usa.com 7 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B When using a trimmer head (2) with a two piece type blade guard, attach the guard extension to the blade guard. (Fig. 1-9) Then loca te the guard above the gear case. (Fig . 1-8B) NOTE! If your unit has guard location label on the drive shaft tube, follow the ...

  • Tanaka TBC-2251 - page 9

    www.tanaka-usa.com 8 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 4. Operating procedures Fuel (Fig. 2-1) WARNING! The trimmer is equipped with a two-stroke engine. Always run t he engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel. Fuel • Always use branded 89 oc tane unleaded ...

  • Tanaka TBC-2251 - page 10

    www.tanaka-usa.com 9 custsvc@tanaka-i sm.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B CAUTION! Before starting, make sure the cutting attachment is not touching anything. Starting (Fig. 2-2, 2B) 1. Set ignition switch (1) to the ON position. (Fig. 2-2) *Push priming bulb (4) several times so that fu el flows through return pipe (5) (if so equi ...

  • Tanaka TBC-2251 - page 11

    www.tanaka-usa.com 10 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Cutting (Fig. 2-4, 4B, 4C, 4D) • When cutting, operate engine at ov er 6500 rpm. Extended use at a slow speeds may wear the clutch prematurely. • Cut grass from right to left. • Blade thrust may occur when the spinning blade contacts a solid object in th ...

  • Tanaka TBC-2251 - page 12

    www.tanaka-usa.com 11 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 5. Maintenance MAINTENANCE, REPLA CEMENT, OR REPAIR OF THE EMISSION CONT ROL DEVICES AND SYSTEMS MAY BE PERF ORMED BY ANY NONROAD ENGINE REPAIR ESTABLISHMEN T OR INDIVIDUAL. Carburetor adjustment (Fig. 3-1) WARNING! The cutting attachem ent my be spinning duri ...

  • Tanaka TBC-2251 - page 13

    www.tanaka-usa.com 12 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B NOTE! If element is hard due to excessive dirt buildu p , re p lace it. Drain all fuel from fuel tank and pull fuel filter line from tank. Pull filter element out of holder assembly and rinse element in warm water with detergent. Rinse thoroughly until all tr ...

  • Tanaka TBC-2251 - page 14

    www.tanaka-usa.com 13 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Flexible drive shaft (Fig. 3-5) Flexible drive shaft should be rem oved and lubricated with a good quality lithium grease every 20 hours. To remove the flexible shaft, first remove screw (1), loosen bolt (2 ) and remo ve the gear case t hen pull the shaft out ...

  • Tanaka TBC-2251 - page 15

    www.tanaka-usa.com 14 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Maintenance schedule Below you will find some genera l maintenance instructions. For further information please contact your Tanaka service dealer. Daily maintenance • Clean the exterior of th e unit. • Check that the harness i s undamaged. • Check the b ...

  • Tanaka TBC-2251 - page 16

    www.tanaka-usa.com 15 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 6. Optional Installation of free disk set (optional) (Fig. 4-1, 1 B) 1) Disassemble free disk (7) from the free disk set by loosening three bolts (8). 2) Place blade (3) as shown in drawing. Disk fixing bolt (4) is left-hand threaded ' Use speci a l care ...

  • Tanaka TBC-2251 - page 17

    www.tanaka-usa.com 16 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B 7. Specifications NOTE: Sound levels are calculated as the time-weighte d energy total under v arious working conditions with the following time distribution: ½ idling, ½ racing. All dat a subjec t to change without notice. ...

  • Tanaka TBC-2251 - page 18

    www.tanaka-usa.com 17 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Declaration of conformity D6claration de conformit6 Dichiarazione di conformita Konformitiitserkliirung Declaraci6n de conformidad Konformitetsdeklaration Tanaka Kogyo Co., Ltd., 3-4- 29 Tsudanum a, Narashino, Chiba, Ja pan TBC-2211/221ID /2251 Declare under o ...

  • Tanaka TBC-2251 - page 19

    www.tanaka-usa.com 18 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B IMPORTANT NOTICE THIS INFORMATION IS FOR TH E US AND CANADIAN MARKETS ONLY. • To reduce the risk of injury from loss of control, never use a metal blade on a curved shaft gr ass trimmer. • Never use a metal blade on any brush cutter without barrier bar or ...

  • Tanaka TBC-2251 - page 20

    www.tanaka-usa.com 19 custsvc@tanaka-ism.com Owner’s Manual TBC-2211,TBC-2251,TBC-230/B Cutting Attachments for Tanaka Trimmers and Brushcutters 1) Fixed line commercial cutting heads offer excellent dur ability and light weight. Great for commercial use. 2) Tanaka Brain fully automatic heads. T he Brain se nses when more line is needed and utili ...

Manufacturer Tanaka Category Trimmer

Documents that we receive from a manufacturer of a Tanaka TBC-2251 can be divided into several groups. They are, among others:
- Tanaka technical drawings
- TBC-2251 manuals
- Tanaka product data sheets
- information booklets
- or energy labels Tanaka TBC-2251
All of them are important, but the most important information from the point of view of use of the device are in the user manual Tanaka TBC-2251.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Tanaka TBC-2251, service manual, brief instructions and user manuals Tanaka TBC-2251. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Tanaka TBC-2251.

Similar manuals

A complete manual for the device Tanaka TBC-2251, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Tanaka TBC-2251 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Tanaka TBC-2251.

A complete Tanaka manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Tanaka TBC-2251 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Tanaka TBC-2251, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Tanaka TBC-2251, that we can find in the current document
3. Tips how to use the basic functions of the device Tanaka TBC-2251 - which should help us in our first steps of using Tanaka TBC-2251
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Tanaka TBC-2251
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Tanaka TBC-2251 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Tanaka TBC-2251?

Use the form below

If you did not solve your problem by using a manual Tanaka TBC-2251, ask a question using the form below. If a user had a similar problem with Tanaka TBC-2251 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)