English dropdown-ico

Manual Meyer Sound SB-1

11 pages 1.12 mb
Download

Go to site of 11

Summary
  • Meyer Sound SB-1 - page 1

    Copyright  1998 Meyer Sound Laboratories, Inc. All rights reserved Part Number 05.049.048.01 A Operati n g Instruc tions SB-1 Parabolic Sound Beam ...

  • Meyer Sound SB-1 - page 2

    2 Pour indiquer les risques résultant de tensions dangereuses Zu die gefahren von gefährliche spanning zeigen Important operating instructions Pour indequer important instructions Zu wichtige betriebs- anweisung und unter- haltsanweisung zeigen Frame or chassis Masse, châssis Rahmen oder chassis Protective earth ground Terre de protection Die sc ...

  • Meyer Sound SB-1 - page 3

    3 Product Summary The Meyer SB-1 Parabolic Sound Beam is the first device that propagates sound waves with SPLs that decrease as little as 3 d B per doubling of distance for more than 300 ft, across a five-octave frequency range, with a consistent and narrow beam width. The physical construction of the SB-1 consists of a fiberglass parabolic reflec ...

  • Meyer Sound SB-1 - page 4

    4 The minimum electrical service amperage required by a system of SB-1s is the sum of the maximum continuous RMS current for each speaker . We recommend allowing an additional 30% above the minimum amperage to pre- vent peak voltage drops at the service entry . Safety Issues Pay close attention to these important electrical and safety issues. Use a ...

  • Meyer Sound SB-1 - page 5

    5 AC T roubleshooting If the Active lamp does not light after connection to an AC source for three seconds, the problem is probably in the power supply . In the unlikely case that the circuit breakers trip (the white center buttons pop out), the amplifier or power supply may be malfunctioning. Do not reset the breakers! Contact Meyer Sound for repa ...

  • Meyer Sound SB-1 - page 6

    6 Fans and Cooling System The SB-1 uses a forced-air cooling system with two fans to prevent the amplifiers from overheating. A variable -speed primary fan runs continuously with an inaudible operating noise of 22 dBA at 1 m at its slowest speed. The speed of the primary fan begins increasing when the temperature of the heatsinks reaches 42°C. The ...

  • Meyer Sound SB-1 - page 7

    7 Lay the positioning yoke on the ground so that the hole closest to the front of the yoke is aligned with the 3 / 4 ” threaded rigging hole on both sides of the SB-1 . Place the split washer on the 3 / 4 ” grade rigging bolt and then place the flat washer on top of split washer so that the split washer is closest to the bolt head. Hand thread ...

  • Meyer Sound SB-1 - page 8

    8 Cover Removal and Installation The Dish cover is held in place by four sets of C-brackets and locking pins as shown below . It is easier to remove the dish cover if the pins and brackets are not supporting the entire weight of the cover . T o ease the stress on the pins, loosen the 3 / 4 ” grade rigging bolt on the positioning yoke and angle th ...

  • Meyer Sound SB-1 - page 9

    9 While keeping a firm grip on the pod insert one of the legs into a c-bracket so that the holes in the legs are aligned with the holes in the c-bracket. Then insert a pin through the holes while pressing down on its button head. When the first pin is in position attach the leg opposite to the first one. Repeat this process until all four legs are ...

  • Meyer Sound SB-1 - page 10

    10 • T o r educe the risk of electric shock, disconnect the loud- speaker from the AC mains before installing audio cable. Reconnect the power cord only after making all signal connections. • Connect the loudspeaker to a two-pole, three wire grounding mains receptacle. The r eceptacle must be connected to a fuse or circuit breaker . Connection ...

  • Meyer Sound SB-1 - page 11

    11 Controls and Connectors European Rear User Panel with IEC 309 connector Rear User Panel shown with the optional Remote Monitoring System (RMS) panel Packed for shipping (with yoke) Front Side Physical Dimensions 48.5 18.0 54.0 54.0 Weight : SB-1: 293 lb (133 kg); SB-1 with yoke: 392 lb (178 kg) Meyer Sound Laboratories, Inc. 2832 San Pablo Avenu ...

Manufacturer Meyer Sound Category Satellite TV System

Documents that we receive from a manufacturer of a Meyer Sound SB-1 can be divided into several groups. They are, among others:
- Meyer Sound technical drawings
- SB-1 manuals
- Meyer Sound product data sheets
- information booklets
- or energy labels Meyer Sound SB-1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Meyer Sound SB-1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Meyer Sound SB-1, service manual, brief instructions and user manuals Meyer Sound SB-1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Meyer Sound SB-1.

Similar manuals

A complete manual for the device Meyer Sound SB-1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Meyer Sound SB-1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Meyer Sound SB-1.

A complete Meyer Sound manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Meyer Sound SB-1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Meyer Sound SB-1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Meyer Sound SB-1, that we can find in the current document
3. Tips how to use the basic functions of the device Meyer Sound SB-1 - which should help us in our first steps of using Meyer Sound SB-1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Meyer Sound SB-1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Meyer Sound SB-1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Meyer Sound SB-1?

Use the form below

If you did not solve your problem by using a manual Meyer Sound SB-1, ask a question using the form below. If a user had a similar problem with Meyer Sound SB-1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)