English dropdown-ico

Manual Cub Cadet 521E

20 pages 1.68 mb
Download

Go to site of 20

Summary
  • Cub Cadet 521E - page 1

    Single Stage Snow Thrower Model 521E Oper ator’ s Man ual PRINTED IN U .S.A. FORM NO . 770-10050 B.fm (5/2000 ) IMPOR T ANT : Read saf ety rules and in structions carefully CUB CADET CORP . P .O . BO X 368023 CLEVELAND , OHIO 44136-9722 Warning: This uni t is equipped with an internal combustion engine and should not be used on or near any unimpr ...

  • Cub Cadet 521E - page 2

    2 TABLE OF CONTENTS Content Page Important Safe Ope ration Practi ces ................. ............. ............ .................... .... 3 Assemb ling Your Snow Thro wer ............... ............. ................... ............. ........... 5 Know Yo ur Sno w Thrower ............ .................... ............. ................... ..... ...

  • Cub Cadet 521E - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: Th is sym bol point s out im portant sa fety inst ructions which, if n ot fol lowed, cou ld endang er the personal safety an d/or prop erty of yo urself and others. Rea d and foll ow all i nstructio ns in this manual before attemptin g to operat e this machi ne. Failure to comply wi th these ...

  • Cub Cadet 521E - page 4

    4 6. Do not operate m achine wh ile under the influ ence of alcohol or dru gs. 7. Muffler and engine beco me hot and can cause a burn. Do not touc h. 8. Exercise extreme ca ution when operat ing on or crossin g grav el su rfac es. St ay al ert f or hi dden ha zar ds or t raffi c. 9. Exercise caution when chan ging direction and while operating on s ...

  • Cub Cadet 521E - page 5

    5 SECTION 2: ASSEMBLING YOUR SNOW THROWER Unpacking Fr om Carton • Cut along c orners of the c arton and lay it do wn flat. See Figu re 1. Remove packing ma terial. • Remove an y loose par ts included with unit (i.e ., operator ’ s manual, etc.) . • Roll unit out of carton. Ch eck car ton thorough ly for any remaini ng loose part. Figure 1 ...

  • Cub Cadet 521E - page 6

    6 • Lift the con trol handl e up, and hook th e “ Z ” end of the c ontr ol ca ble i nto t he bottom hole in the co ntrol handle, fro m the outside to the inside . If neces sary, pull up on th e end of the cable with a pair of pli ers to obta in slac k in orde r to hoo k it into the cont rol handle. Hol d the “ Z ” fitting with the pl iers ...

  • Cub Cadet 521E - page 7

    7 SECTION 3: KNOW YOUR SNOW THROWER Be famil iar with all the c ontrols and the ir prope r operation. K now how to stop the m achin e and diseng age them qu ickly. Figure 9 • Compare Figure 9 with the co ntrols on you r snow thrower befor e startin g the machin e or trying to operate it . Choke Lever Place ch oke lever in “ ON ” position to s ...

  • Cub Cadet 521E - page 8

    8 SECTION 4: OPERATING YOUR SNOW THROWER Before Starting WARN ING: Read, understan d, and follow all inst ructions and warni ngs on the ma chine and in this m anual befor e operatin g. • The s park pl ug wire was discon nected f or safe ty purpose s during as sembly . Attach sp ark plug wi re to spar k plug b efore s tarting. Fuel & Oil Mixtu ...

  • Cub Cadet 521E - page 9

    9 • Wipe al l snow and mo isture from the unit . Move the choke lev er back and fo rth sever al times and leave it in the ON pos ition . Operat ing Tips • Discha rge snow dow nwind whenev er possibl e. Slightl y overla p each previo usly cl eared path. • Lifting up on the handle wi ll allow the rubb er on the augers to propel the snow thrower ...

  • Cub Cadet 521E - page 10

    10 If addit ional adj ustmen t is requir ed, foll ow steps be low. • Remove the bel t cover by removi ng five hex scre ws that hold it in place. For loca tion of the be lt cover , see Figu re 16. • There are three ad justment ho les prov ided in the idler br acket as sembly. F or loca tion of thes e holes, see Figu re 15. Fig ure 15 • To adju ...

  • Cub Cadet 521E - page 11

    11 WARNING: B efore s ervicing , repairi ng, or inspec ting, diseng age al l clutch levers and stop engi ne. Wait unt il all moving par ts have come to a co mplete s top. Disconn ect spar k plug wir e and ground it against the engine to preve nt unintende d starting . Repl acing Sh ave P late The shave pl ate is subjec t to wear. It should be check ...

  • Cub Cadet 521E - page 12

    12 SECTION 8: TROUBLESHOOTING GUIDE NOTE: For rep airs beyon d the minor adjustmen ts listed above, call the Custom er Dealer Line at 1-80 0-528-1009 for the dealer nearest you. Ref er to separ ate engine ma nual, pack ed with your sno w throwe r, for engine info rmation. Problem Cause Remedy Engine fai ls to sta rt 1. Fuel tan k empty , or st ale ...

  • Cub Cadet 521E - page 13

    13 SECTION 9: PARTS LIST FOR MODEL 521E Ref. No. P art No. Descriptio n 1. 710-0487 Carria ge Screw 2. 710-1270 Oval C-Sunk Machine Scre w 3. 712-0324 Hex Loc k Nut 4. 720-0284 Wing Nut 5. 720-0295 Foam G rip: Ha ndle 6. 725-0157 Cable Tie 7. 736-0451 Saddle Was her 8. 746-0883 Cable Housing w/o Throt tle 9. 747-0956 Auger Bail: Gull Wing 10. 749-0 ...

  • Cub Cadet 521E - page 14

    14 Model 521E 7 22 10 46 37 31 34 13 21 38 3 30 35 6 27 39 40 1 20 14 6 35 30 6 5 28 25 45 42 13 44 7 22 33 9 17 18 15 4 2 11 26 19 26 16 32 23 12 36 41 8 ...

  • Cub Cadet 521E - page 15

    15 Model 521E Ref. No. P art No. P art De scription 1. 710-0167 Carriage Bo lt 2. 710-0276 Carriage Bo lt 3. 710-0323 Pan Head Sc rew 4. 710-0451 Carriage Bo lt 5. 710-0642 Hex Wash er Screw 6. 710-1005 Hex Wash er Screw 7. 710-0773 Hex Wash er Screw 8. 710-0896 Hex Wash er Screw 9. 710-3015 Hex Cap Sc rew 10. 711-0 848A Ax le 11. 712-0 429 Hex Cen ...

  • Cub Cadet 521E - page 16

    16 Model 521E 5 3 5 20 29 22 16 7 4 6 23 8 9 27 2 10 28 26 21 7 25 7 13 15 14 19 18 24 11 17 ...

  • Cub Cadet 521E - page 17

    17 Model 521E Ref. No. P art N o. Pa rt Description 1. 684-0054A Dash Assemb ly 2. 684-0126 Chute Crank Assembl y 3. 710-1003 Special Screw: 310-16 x 0.375 ” 4. 710-1090 Hex Flange Screw 5/16-18 x 1.25 ” 5. 710-1268 Special sc rew 6. 710-1652 Self-Tapping Screw 1/4 -20 x .625 ” 7. 712-3010 Hex Nut 5/16-18 8. 714-0104 Hairpin Clip 9. 714-0507 ...

  • Cub Cadet 521E - page 18

    18 Model 521E NOTE: For painted pa rts , please ref er to the list of c olor codes b elow. Plea se add th e applica ble color c ode, wherever needed , to the part number to order a replace ment part. For in stance, if a part, numbered 70 0- xxxx, is p ainted C ub Yellow, the part number to order would be 700-xx xx-0716. Cub Yell ow: 0716 Cub Bei ge ...

  • Cub Cadet 521E - page 19

    19 Model 521E ...

  • Cub Cadet 521E - page 20

    MANUF A C TURER ’ S LIMITED W ARRAN TY FOR: TWO-YEAR RESIDENTIAL ONE-YEAR COMMERCIAL Prope r maintenance of your Cub Cadet equi pment is the own er ’ s res ponsibi lity. Fol low t he instr uctions in yo ur operator ’ s manual for cor rect lub ricants a nd mainte nance schedul e. Your Cub Cadet deale r carri es a comple te line of qual ity lu ...

Manufacturer Cub Cadet Category Snow Blower

Documents that we receive from a manufacturer of a Cub Cadet 521E can be divided into several groups. They are, among others:
- Cub Cadet technical drawings
- 521E manuals
- Cub Cadet product data sheets
- information booklets
- or energy labels Cub Cadet 521E
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cub Cadet 521E.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cub Cadet 521E, service manual, brief instructions and user manuals Cub Cadet 521E. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cub Cadet 521E.

Similar manuals

A complete manual for the device Cub Cadet 521E, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cub Cadet 521E by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cub Cadet 521E.

A complete Cub Cadet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cub Cadet 521E - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cub Cadet 521E, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cub Cadet 521E, that we can find in the current document
3. Tips how to use the basic functions of the device Cub Cadet 521E - which should help us in our first steps of using Cub Cadet 521E
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cub Cadet 521E
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cub Cadet 521E in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cub Cadet 521E?

Use the form below

If you did not solve your problem by using a manual Cub Cadet 521E, ask a question using the form below. If a user had a similar problem with Cub Cadet 521E it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)